Dichromatic LED Lamp GL3ED8 ø3mm(T-1), Cylinder Type, Milky Diffusion, Dichromatic LED Lamp for Backlight/Indicator GL3ED8 ■ Outline Dimensions ø3.8 Protruded resin 1.0MAX ■ Radiation Diagram (Unit : mm) (Ta=25˚C) Milky diffusion ø3.0 -20˚ -10˚ +10˚ 0˚ +20˚ +30˚ 100 5.0 4.4 -30˚ -40˚ Yellow-green +40˚ Red Relative luminous intensity(%) 1.0±0.5 23.0MIN 80 -50˚ -60˚ 0.5±0.1 -70˚ (4.0) (2.0) -80˚ +50˚ 60 +60˚ 40 +70˚ 20 +80˚ +90˚ -90˚ 0 0.5±0.1 2.0 2.0 NOM NOM 1 2 3 Pin connections 1 Anode(Yellow-green) 2 Cathode(Common) 3 Anode(Red) Unspecified tolerance:±0.2 ■ Absolute Maximum Ratings (Ta=25˚C) Power dissipation Forward current Peak forward current P*1 IF IFM*2 Model No. Radiation color Radiation material (mW) (mA) (mA) GL3ED8 Yellow-green GaP Red GaAsP on GaP 84 84 30 30 Derating factor Reverse voltage Operating temperature Storage temperature Soldering temperature (mA/˚C) VR Topr Tstg Tsol*3 (V) (˚C) (˚C) (˚C) DC Pulse 0.40 0.40 50 50 0.67 0.67 5 5 -25 to +85 -25 to +100 260 *1 The value is specified under the condition that either color is lightened separately. When the both diodes are lightened simultaneously, the power dissipation of each diode should be less than the half of the value specified in this table. *2 Duty ratio=1/10, Pulse width=0.1ms *3 5s or less(At the position of 1.6mm or more from the bottom face of resin package) ■ Electro-optical Characteristics Radiation Lens Model No. color type Milky Yellow-green GL3ED8 diffusion Red (Notice) Forward voltage VF(V) TYP 2.1 2.0 Peak emission wavelength IF λp(nm) (mA) TYP MAX 2.8 565 20 2.8 635 20 (Ta=25˚C) Luminous intensity IF IV(mcd) (mA) TYP 20 15 20 20 Spectrum radiation bandwidth IF ∆λ(nm) (mA) TYP 30 35 20 20 Reverse current VR IR(µA) (V) MAX 10 10 4 4 Page for characteristics (MHZ) diagrams → 1 → 1 Terminal capacitance Ct(pF) TYP 35 20 ¡In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in equipment using any SHARP devices shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device. 70 (Internet) ¡Data for sharp's optoelectronic/power device is provided for internet.(Address http://www.sharp.co.jp/ecg/) LED Lamp Characteristics Diagrams EG series Forward Current vs. Forward Voltage(Note) Forward Current Derating Curve Luminous Intensity vs. Ambient Temperature(Note) (Ta=25˚C) 100 60 (Ta=25˚C) 1000 50 500 40 30 20 Relative luminous intensity(%) Forward current IF(mA) Forward current IF(mA) 50 10 5.0 1.0 0.5 100 50 10 5.0 10 0 -25 0 25 50 75 85 100 0.1 1.0 125 1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4 2.6 -20 0 Forward voltage VF(V) Ambient temperature Ta(˚C) Peak Forward Current Derating Curve 40 60 80 100 120 Duty Ratio vs. Peak Forward Current Luminous Intensity vs. Forward Current(Note) 60 20 Ambient temperature Ta(˚C) (Ta=25˚C) (Ta=25˚C) 1000 500 500 200 200 40 30 20 Peak forward current IFM(mA) Relative luminous intensity(%) Peak forward current IFM(mA) 50 100 50 20 10 5.0 100 50 20 10 5.0 10 2.0 2.0 0 -25 0 25 50 75 85 100 1.0 0.1 125 1.0 0.2 0.5 Ambient temperature Ta(˚C) 1 2 5 10 20 1/50 50 1/20 1/10 1/5 1/2 1 Duty ratio DR Forward current IF(mA) Note)Characteristics shown in diagrams are typical values. (not assurance value) KG series Forward Current vs. Forward Voltage(Note) Forward Current Derating Curve Luminous Intensity vs. Ambient Temperature(Note) (Ta=25˚C) 100 60 (Ta=25˚C) 1000 50 500 40 30 20 Relative luminous intensity(%) Forward current IF(mA) Forward current IF(mA) 50 10 5.0 1.0 0.5 100 50 10 5.0 10 0 -25 0 25 50 75 85 100 0.1 1.0 125 1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4 2.6 -20 0 Forward voltage VF(V) Ambient temperature Ta(˚C) Peak Forward Current Derating Curve Luminous Intensity vs. Forward Current(Note) 60 20 40 60 80 100 120 Ambient temperature Ta(˚C) Duty Ratio vs. Peak Forward Current (Ta=25˚C) (Ta=25˚C) 1000 500 500 200 200 40 30 20 Peak forward current IFM(mA) Relative luminous intensity(%) Peak forward current IFM(mA) 50 100 50 20 10 5.0 100 50 20 10 5.0 10 2.0 2.0 0 -25 0 25 50 75 85 Ambient temperature Ta(˚C) 100 125 1.0 0.1 1.0 0.2 0.5 1 2 5 10 20 Forward current IF(mA) 50 1/50 1/20 1/10 1/5 1/2 1 Duty ratio DR Note)Characteristics shown in diagrams are typical values. (not assurance value) (Notice) ¡ In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in equipment using any SHARP shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device. 120 (Internet) ¡ devices Data for sharp's optoelectronic/power device is provided for internet.(Address http://www.sharp.co.jp/ecg/) LED Lamp Characteristics Diagrams PR series Forward Current Derating Curve Forward Current vs. Forward Voltage(Note) 60 Luminous Intensity vs. Ambient Temperature(Note) (Ta=25˚C) 100 (Ta=25˚C) 1000 500 50 40 30 20 Relative luminous intensity(%) Forward current IF(mA) Forward current IF(mA) 50 10 5.0 1.0 0.5 100 50 10 5.0 10 0 -25 0 25 50 75 85 100 0.1 1.0 125 1.0 1.2 1.4 Ambient temperature Ta(˚C) 1.6 1.8 2.0 2.2 2.4 -20 2.6 0 Luminous Intensity vs. Forward Current(Note) Peak Forward Current Derating Curve 40 60 80 100 120 Duty Ratio vs. Peak Forward Current (Ta=25˚C) 1000 60 20 Ambient temperature Ta(˚C) Forward voltage VF(V) (Ta=25˚C) 500 500 200 200 40 30 20 Peak forward current IFM(mA) Relative luminous intensity(%) Peak forward current IFM(mA) 50 100 50 20 10 5.0 100 50 20 10 5.0 10 2.0 0 -25 0 25 50 75 85 100 1.0 0.1 125 2.0 1.0 0.2 0.5 1 2 5 10 20 1/50 50 1/20 1/10 Forward current IF(mA) Ambient temperature Ta(˚C) 1/5 1/2 1 Duty ratio DR Note)Characteristics shown in diagrams are typical values. (not assurance value) HD series Forward Current vs. Forward Voltage(Note) Forward Current Derating Curve Luminous Intensity vs. Ambient Temperature(Note) (Ta=25˚C) 100 60 (Ta=25˚C) 1000 50 500 40 30 20 Relative luminous intensity(%) Forward current IF(mA) Forward current IF(mA) 50 10 5.0 1.0 0.5 100 50 10 5.0 10 0 -25 0 25 50 75 85 100 0.1 1.0 125 1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4 2.6 -20 0 Forward voltage VF(V) Ambient temperature Ta(˚C) Luminous Intensity vs. Forward Current(Note) Peak Forward Current Derating Curve 40 60 80 100 120 Duty Ratio vs. Peak Forward Current (Ta=25˚C) (Ta=25˚C) 1000 60 20 Ambient temperature Ta(˚C) 500 500 200 200 40 30 20 Peak forward current IFM(mA) Relative luminous intensity(%) Peak forward current IFM(mA) 50 100 50 20 10 5.0 100 50 20 10 5.0 10 2.0 2.0 0 -25 0 25 50 75 85 Ambient temperature Ta(˚C) 100 125 1.0 0.1 1.0 0.2 0.5 1 2 5 10 20 Forward current IF(mA) 50 1/50 1/20 1/10 1/5 1/2 1 Duty ratio DR Note)Characteristics shown in diagrams are typical values. (not assurance value) (Notice) ¡ In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in equipment using any SHARP shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device. 118 (Internet) ¡ devices Data for sharp's optoelectronic/power device is provided for internet.(Address http://www.sharp.co.jp/ecg/)