SHARP LT260

Hall IC
LT260A
GaAs Hall IC for Noncontact Switch
(Alternating magnetic field-type*)
LT260A
2
■ Applications
2.9±0.2
0.95
2.9±0.2
1.9
0.85
0.6
0.4
*Zero-cross is not warranted.
■ Features
¡Operation by small magnet due to high sensitivity ■ Outline Dimensions
(Unit : mm)
Operating point<10mT
2.7±0.3
¡Combining a GaAs Hall device and an IC in a compact
Y
package (2.9X1.5X1.1mm)
1
4
¡Wide operation temperature range obtained by GaAs Hall
device (-20 to +125˚C)
¡Long life time due to noncontact-type
S
Z
3
0.4
¡FDD
¡HDD
¡Water meter
¡Car stereo
¡Microswitch,etc.
0.4
X
Symbol
VCC
VOUT
IO
PD
Topr
Tstg
Tsol
Rating
18
18
5
100
-20 to +125
-55 to +150
260
Unit
V
V
mA
mW
˚C
˚C
˚C
+0.2
0.8
1.1-0.1
(0to0.15)
Parameter
Supply voltage
Output voltage
Output current
Power dissipation
Operating temperature
Storage temperature
Soldering temperature* 1
(Ta=25˚C)
-
1 : VCC
2 : VOUT
3 : Don't use.
4 : GND
*No.3 terminal and the section of leads(both sides
of package in X directionÅjare connected with the
terminal of internal IC. Be careful in connecting other circuits.
As for dimensions of tape-packaged products, refer to page 44 .
■ Operating Explanation
Output voltage
■ Absolute Maximum Ratings
0.16+0.10
-0.06
0.3
4-R0.2
Hall device center line
X : +0.05±0.23mm against package center
Y : -0.05±0.1mm against package lead center between
No.2 and No.3 terminals
Z : 0.81±0.15mm from package surface
Terminal connections
1.5±0.2
0.6
0.6
REG
Hall
device
+
H
*1 Soldering time : within 10 seconds
<Alternating magnetic field-type>
BRP 0 BOP
+B
Magnetic flux density
■ Electrical Characteristics
Parameter
Operating magnetic flux density
Hysteresis breadth
Operating voltage
Supply current
Low level output voltage
Output leakage current
Operating point temperature drift
(Ta=25˚C)
Symbol
BOP
BRP
BH
VCC
ICC
VOL
IOH
∆BOP
Conditions
VCC=16V
VOO=16V
RL=10kΩ
VCC=16V, B=<-10mT
IO=4mA, B>=10mT
VCC=16V, B=<10mT, VOO=16V
VCC=16V, Ta=-20˚C to +80˚C
MIN.
-10
4.5
-6
TYP.
-
MAX.
10
5
16
10.5
0.4
10
6
Unit
mT
mT
mT
V
mA
V
µA
mT
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in equipment using any SHARP devices
shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device spcification sheets before using any SHARP device.
Hall IC
LT260A
Ta=25˚C
12
8
4
BOP
0
BRP
-4
-8
-12
0
4
8
12
16
Supply voltage VCC (V)
Fig. 3
2
Fig. 5
0
4
8
12
16
Supply voltage VCC (V)
Low level output voltage VOL (V)
0.5
0.4
-12
Fig. 4
0.2
0.1
0
1
2
3
4
Output current IO (mA)
5
Supply Current vs. Ambient
Temperature
VCC=16V
B=<-10mT
8
6
4
2
0
0.5
0.3
0
-8
Fig. 6
VCC=16V
B>=10mT
Ta=25˚C
BRP
-4
-40
0
40
80
120
Ambient temperature Ta (˚C)
20
Low Level Output Voltage vs.
Output Current
BOP
0
Supply current ICC (mA)
Supply current ICC (mA)
4
VCC=16V
4
10
6
Operating Magnetic Flux Density
vs. Ambient Temperature
8
B=<-10mT
Ta=25˚C
8
0
12
20
Supply Current vs. Supply Voltage
10
Fig. 2
Operating magnetic flux density B (mT)
Operating Magnetic Flux Density
vs. Supply Voltage
Low level output voltage VOL (V)
Operating magnetic flux density B (mT)
Fig. 1
0.4
-40
0
40
80
120
Ambient temperature Ta (˚C)
Low Level Output Voltage vs.
Ambient Temperature
VCC=16V
IO=4mA
B>=10mT
0.3
0.2
0.1
0
-40
0
40
80
120
Ambient temperature Ta (˚C)