PQ05RR12/PQ05RR13 Low Power-Loss Voltage Regulators PQ05RR12/13 1A Output, Low Power-Loss Voltage Regulators(Built-in Reset Signal Generating Function) ■ Outline Dimensions (Unit : mm) 4.5±0.2 10.2MAX PQ05RR12 ■ Applications ¡Series power supply for equipment such as TVs, VCRs and electronic music instruments φ3.2±0.1 4-1.4 +0.3 -0 4-0.6 +0.2 -0.1 4.8MAX 15.6±0.5 7.4±0.2 3.6±0.2 2.8±0.2 13.5MIN ¡Compact resin full-mold package ¡Low power-loss (Dropout voltage : MAX. 0.5V) ¡The regulators are provided with reset signal generating function to prevent errors of microcomputer when input voltage is applied and output voltage drops. ¡High-precision output type (Output Voltage precision : ±2.5%) (PQ05RR13) 29.1MAX ■ Features (1.5) (0.5) 3-(2.54) 1 ● 2 ● 3 ● 4 ● Internal connection diagram 1 2 Specific IC 4 1 DC input (VIN) 2 DC output (VO) 3 GND 4 Reset signal output (Vr) 3 ■ Absolute Maximum Ratings Parameter *1 *1 *2 *3 *1 *2 *3 Input voltage Reset output voltage Output current Reset output current Power dissipation (No heat sink) Power dissipation (With infinite heat sink) Junction temperature Operating temperature Storage temperature Soldering temperature (Ta=25˚C) Symbol VIN Vr IO Ir PD1 PD2 Tj Topr Tstg Tsol Rating 24 24 1 10 1.5 15 150 -20 to +80 -40 to +150 260 Unit V V A mA W W ˚C ˚C ˚C ˚C All are open except GND and applicable terminals. Overheat protection may operate at 125=<Tj=<150˚C. For 10s · Please refer to the chapter“ Handling Precautions ”. “ In the absence of confirmation by device specification sheets,SHARP takes no responsibility for any defects that may occur in equipment using any SHARP devices shown in catalogs,data books,etc.Contact SHARP in order to obtain the latest version of the device specification sheets before using any SHARP's device. ” Low Power-Loss Voltage Regulators ■ Electrical Characteristics (Unless otherwise specified, condition shall be VIN=7V,Io=0.5A, Ta=25˚C) Parameter PQ05RR12 Output voltage PQ05RR13 Load regulation Line regulation Temperature coefficient of output voltage Ripple rejection Dropout voltage Low reset output voltage Reset threshold voltage Reset output leak current Quiescent current Symbol Conditions VO - MIN. 4.75 4.88 45 3.55 - IO=5mA to 1.0A VIN=6 to 12V TJ=0 to 125˚C Refer to Fig. 2 RegL RegI TCVO RR Vi-o Vrl Vrt Irlk Iq *4 IO=5mA, Ir=5mA IO=5mA, *5 IO=5mA, Vr=24V IO=0 TYP. 5.0 5.0 0.1 0.5 ±0.02 55 3.75 - MAX. 5.25 5.12 2.0 2.5 0.5 0.8 3.95 30 10 Unit V % % %/˚C dB V V V µA mA Input voltage shall be the value when output voltage is 95% in comparison with the initial value. Output voltage shall be the value when input voltage lowers and Vr becomes low. Fig.1 Test Circuit VIN 1 ● Fig.2 Test Circuit of Ripple Rejection Ir 4 ● 3 ● 0.33µF A Iq Irlk 1 ● + 2 ● ~ ei IO A + V A Vrl VO 47µF 2 ● IO 4 ● + 3 ● V RL VIN 0.33µF 47µF RL V ~ eo Vr f=120Hz (sine wave) ei=0.5Vrms RR=20 log (ei/eo) Fig.3 Power Dissipation vs. Ambient Temperature 20 PD1 :No heat sink PD2 :With infinite heat sink 15 PD2 10 5 PD1 0 -20 0 50 100 150 Ambient temperature Ta (˚C) Note) Oblique line portion:Overheat protection may operate in this area. Fig.4 Overcurrent Protection Characteristics (Typical value) 100 Relative output voltage (%) *5 Power dissipation PD (W) *4 PQ05RR12/PQ05RR13 80 60 40 20 0 0 0.3 0.6 0.9 1.2 1.5 1.8 Output current IO (A) 2.1 PQ05RR12/PQ05RR13 Low Power-Loss Voltage Regulators Fig.5 Output Voltage Deviation vs. Junction Temperature Fig.6 Output Voltage vs. Input Voltage 7 VIN=7V IO =0.5A 40 6 Output voltage VO (V) Output voltage deviation ∆VO (mV) 60 20 0 -20 5 4 3 -40 RL=10Ω RL=5Ω 1 -60 -25 0 125 0 25 50 75 100 Junction temperature Tj (˚C) Fig.7 Circuit Operating Current vs. Input Voltage 0 RL=5Ω RL=10Ω 10 Quiescent current Iq (mA) 20 RL=∞ 0 0 1 2 3 4 5 6 7 8 Input voltage VIN (V) 3 4 5 6 7 8 Input voltage VIN (V) 9 10 VIN =24V IO =0A 8 6 4 2 0 -25 9 10 Fig.9 Ripple Rejection vs. Input Ripple Frequency Ripple rejection RR (dB) 50 40 30 VIN=7V 10 ei=0.5Vrms IO =0.5A 0 0 1 10 Input ripple frequency f (kHz) 125 f=120Hz ei=0.5Vrms VIN =7V 70 60 0 25 50 75 100 Junction temperature Tj (˚C) Fig.10 Ripple Rejection vs. Output Current 100 80 Ripple rejection RR (dB) 2 10 30 20 1 Fig.8 Quiescent Current vs. Junction Temperature 40 Circuit operating current IBIAS (mA) RL=∞ 2 80 60 40 20 0 100 0 0.2 0.4 0.6 0.8 Output current IO (A) 1.0 Low Power-Loss Voltage Regulators Fig.11 Output Peak Current vs. Junction Temperature Fig.12 Output Peak Current vs. Dropout Voltage 2.0 IOP :Output current shall be the value when output voltage is 95% in comparison with the initial value. VIN-VO =5V 1.5 Output peak current IOP (A) Output peak current IOP (A) 2.0 2V 1V 0.5V 1.0 -25 0 25 50 75 100 Junction temperature Tj (˚C) PQ05RR12/PQ05RR13 1.5 1.0 125 0 1 2 3 4 Dropout voltage Vi-O (V) 5 Rr=10kΩ 10.0 1.0 0.1 0.01 10-4 10-3 10-2 Time constant τ (CrXRr) 10-1 Reset Vr Tr Rr=10kΩ 0.8V 1 ● VIN Rr 4 ● 3 ● 0 t VO 2 ● Cr Vr + CO Load Reset output voltage delay time Tr (ms) Fig.13 Reset Output Delay Time vs. Time Constant PQ05RR12/PQ05RR13 Low Power-Loss Voltage Regulators ■ Typical Application ■ Reset Output Response Characteristics DC input 1 ● VIN VO 2 ● + Specific IC 3 ● *Open collector output VO + Rr * 4 ● CO RL Vr Cr Reset output