SP690A/692A/802L/ 802M/805L/805M ® Low Power Microprocessor Supervisory with Battery Switch-Over ■ Precision Voltage Monitor: SP690A/SP802L/SP805L at 4.65V SP692A/SP802M/SP805M at 4.40V ■ Reset Time Delay - 200ms ■ Watchdog Timer - 1.6 sec timeout ■ Minimum component count ■ 60µA Maximum Operating Supply Current ■ 0.6µA Maximum Battery Backup Current ■ 0.1µA Maximum Battery Standby Current ■ Power Switching 250mA Output in VCC Mode (0.6Ω) 25mA Output in Battery Mode (5Ω) ■ Voltage Monitor for Power Fail or Low Battery Warning ■ Available in 8 pin SO and DIP packages ■ RESET asserted down to VCC = 1V ■ Pin Compatible Upgrades to MAX690A/692A/802L/802M/805L DESCRIPTION The SP690A/692A/802L/802M/805L/805M are a family of microprocessor (µP) supervisory circuits that integrate a myriad of components involved in discrete solutions to monitor powersupply and battery-control functions in µP and digital systems. The series will significantly improve system reliability and operational efficiency when compared to discrete solutions. The features of the SP690A/692A/802L/802M/805L/805M include a watchdog timer, a µP reset and backup-battery switchover, and power-failure warning, a complete µP monitoring and watchdog solution. The series is ideal for applications in automotive systems, computers, controllers, and intelligent instruments. All designs where it is critical to monitor the power supply to the µP and it’s related digital components will find the series to be an ideal solution. PART NUMBER RESET Threshold RESET Accuracy RESET Active PFI Accuracy SP690A 4.65 V 125mV LOW 4% SP692A 4.40 V 125mV LOW 4% SP802L 4.65 V 75mV LOW 2% SP802M 4.40 V 75mV LOW 2% SP805L 4.65 V 125mV HIGH 4% SP805M 4.40 V 125mV HIGH 4% SP690A/692ADS/08 SP690A/692A Low Power Microprocessor Supervisory with Battery Switch-Over 1 © Copyright 2000 Sipex Corporation ABSOLUTE MAXIMUM RATINGS These are stress ratings only and functional operation of the device at these ratings or any other above those indicated in the operation sections of the specifications below is not implied. Exposure to absolute maximum rating conditions for extended periods of time may affect reliability and cause permanent damage to the device. VCC........................................................-0.3V to 6.0V VBATT.....................................................-0.3V to 6.0V All Other Inputs (NOTE 1)..................-0.3V to (VCC to 0.3V) Input Current: VCC.........................................................250mA VBATT........................................................50mA GND........................................................20mA Output Current: VOUT.....Short-Circuit Protected for up to 10sec All Other Inputs.................................20mA Rate of Rise, VCC,VBATT..................100V/µs Continuous Power Dissipation.......500mW Storage Temperature.......-65°C to +160°C Lead Temperature(soldering,10sec).................+300°C ESD Rating.............................................................4KV SPECIFICATIONS Vcc=4.75v to 5.50V for SP690A/SP802L/SP805L, VCC=4.50V to 5.50V for SP692A/SP802M/SP805M, VBATT=2.80V, TA=TMIN to TMAX, typical specified at 25OC, unless otherwise noted. PARAMETERS MIN. Operating Voltage Range, TYP. MAX. UNITS 5.5 Volts 35 60 µA 0.001 0.6 µA 0.02 µA 0 CONDITIONS VCC or VBATT, Note 2 Supply Current, ISUPPLY, ISUPPLY in Battery Backup Mode, VCC = 0V, VBATT = 2.8V VBATT Standby Current, NOTE 3 VOUT Output VOUT in Battery-Backup Mode VCC < VBATT - 0.2V -0.1 VCC - 0.03 VCC - 0.15 Volts IOUT = 50mA IOUT = 250mA VBATT -0.15 VBATT - 0.04 VBATT - 0.20 Volts IOUT = 5mA IOUT = 25mA 20 -20 mV Power-up Power-down mV Peak to Peak Battery Switchover Hysteresis SP690A/692ADS/08 VCC > VBATT + 0.2V VCC - 0.1 Battery Switch Threshold, VCC to VBATT Reset Threshold excluding IOUT 40 4.50 4.25 4.55 4.30 4.65 4.40 4.75 4.50 4.70 4.45 Volts SP690A, SP802L, SP805L SP692A, SP802M, SP805M SP802L, TA = +25° C, VCC falling SP802M, TA = +25° C, VCC falling SP690A/692A Low Power Microprocessor Supervisory with Battery Switch-Over 2 © Copyright 2000 Sipex Corporation SPECIFICATIONS (continued) Vcc=4.75v to 5.50V for SP690A/SP802L/SP805L, VCC=4.50V to 5.50V for SP692A/SP802M/SP805M, VBATT=2.80V, TA=TMIN to TMAX, typical specified at 25OC, unless otherwise noted. PARAMETERS MIN. Reset Threshold Hysteresis Reset Pulse Width, tRS RESET Output Voltage, 140 Watchdog Timeout, tWD CONDITIONS mV Peak to Peak ms ISOURCE = 800µA 0.1 0.4 0.004 0.3 Volts 1.00 WDI Input Threshold, VCC = 5V, NOTE 4 3.5 ISOURCE = 4µA, VCC = 1.0V, Volts 0.1 0.4 1.60 2.25 sec Volts 50 -50 150 -150 1.200 1.225 1.250 1.250 1.300 1.275 Volts -25 0.01 25 nA 0.1 0.4 VCC - 1.5 ISOURCE = 800µA ISINK = 3.2mA ns 0.8 WDI Input Current ISINK = 3.2mA ISINK = 50µA, VCC = 1.0 0.8 50 PFO Output Voltage 280 UNITS VCC - 1.5 WDI Pulse Width, tWP PFI Input Current 200 VCC - 1.5 NOTE 6 PFI Input Threshold MAX. 40 NOTE 5 RESET Output Voltage, TYP. µA Volts VIL = 0.4V, VIH = (0.8)(VCC) Logic low Logic high WDI =VCC WDI = 0V SP690A/692A, SP805L/M SP802L/M ISOURCE = 800µA ISINK = 3.2mA NOTE 1: The input voltage limits on PFI (pin 4) and WDI (pin 6) may be exceeded if the current into these pins is limited to less than 10 mA. NOTE 2: Either VCC or VBATT can go to 0V if the other is greater than 2.0V. NOTE 3: "-" equals the battery-charging current, "+" equals the battery-discharging current. NOTE 4: WDI is guaranteed to be in an intermediate, non-logic level state if WDI is floating and VCC is in the operating voltage range. WDI is internally biased to 35% of VCC with an input impedance of 50KΩ. NOTE 5: SP690A, SP692A, SP802L, and SP802M only. NOTE 6: SP805L and SP805M only. SP690A/692ADS/08 SP690A/692A Low Power Microprocessor Supervisory with Battery Switch-Over 3 © Copyright 2000 Sipex Corporation VBATT VOUT 1 8 VBATT VCC 2 7 RESET (RESET)* GND 3 6 WDI PFI 4 5 PFO BATTERY-SWITCHOVER CIRCUITRY VCC RESET GENERATOR VOUT RESET (RESET)* 1.25V *( ) SP805 only 3.5V WATCHDOG TIMER WDI Figure 10. Pinout PIN ASSIGNMENTS 0.8V Pin 1 —VOUT — Output Supply Voltage. VOUT connects to VCC when VCC is greater than VBATT and VCC is above the reset threshold. When VCC falls below VBATT and VCC is below the reset threshold, VOUT connects to VBATT. Connect a 0.1µF capacitor from VOUT to GND. PFI PFO 1.25V Pin 2 — VCC — +5V Supply Input *( ) SP805 only Figure 11. Internal Block Diagram Pin3 — GND — Ground reference for all signals Pin 7 for SP805 only — RESET (Active High)– Reset Output is the inverse of RESET; when RESET is asserted, the RESET output voltage = V CC or V BATT , whichever is higher. Pin 4 — PFI — Power-Fail Input. This is the noninverting input to the power-fail comparator. When PFI is less than 1.25V, PFO goes low. Connect PFI to GND or VOUT when not used. Pin 8 — VBATT — Backup-Battery Input. When VCC falls below the reset threshold, VBATT will be switched to VOUT if VBATT is 20mV greater than VCC. When VCC rises 20mV above V BATT , V OUT will be reconnected to V CC . The 40mV hysteresis prevents repeated switching if VCC falls slowly. Pin 5 — PFO — Power-Fail Output. Pin 6 — WDI — Watchdog Input. WDI is a three level input. If WDI remains high or low for 1.6sec, the internal watchdog timer triggers a reset. If WDI is left floating or connected to a high-impedance tri-state buffer, the watchdog feature is disabled. The internal watchdog timer clears whenever reset is asserted. Pin 7 for SP690A/692A/802 only — RESET (Active Low)– Reset Output. RESET Output goes low whenever VCC falls below the reset threshold or whenever WDI remains high or low longer than 1.6 seconds. RESET remains low for 200ms after VCC crosses the reset threshold voltage on power-up or after being triggered by WDI. SP690A/692ADS/08 SP690A/692A Low Power Microprocessor Supervisory with Battery Switch-Over 4 © Copyright 2000 Sipex Corporation TYPICAL CHARACTERISTICS (25oC, unless otherwise noted) VCC Supply Current vs. Temperature (Normal Mode) 2.9 2.4 VCC=0V VBATT=2.8V 1.9 1.4 0.9 0.4 0 30 60 90 -0.1 -60 -40 -20 0 20 40 60 80 100 120 140 120 150 1.250 1.248 1.246 -60 VBATT=2.8V 5 VBATT=4.5V VCC=5V VBATT=0V 0.8 0.7 0.6 0.5 0.4 0.3 -30 0 30 60 90 120 150 -60 -30 Temperature Deg. C 212 Reset Delay (mS) VCC=5V,VBATT=2.8V 500 Soucing Current 400 300 200 VCC=0V,VBATT=2.8V Sink Current -30 0 30 60 90 Temperature Deg. C SP690A/692ADS/08 60 90 120 150 -60 120 150 VCC=0V to 5V Step, VBATT=2.8V 210 208 206 204 202 200 -60 -30 0 30 60 90 90 120 150 VBATT=0V Power Down -30 0 30 60 90 120 150 Battery Current vs. VCC Voltage 120 150 Temperature Deg. C SP690A/692A Low Power Microprocessor Supervisory with Battery Switch-Over 5 60 Temperature Deg. C Reset Delay vs. Temperature 600 0 -60 30 30 SP690A Temperature Deg. C Reset Output Resistance vs. Temperature 100 0 4.70 4.69 4.68 4.67 4.66 4.65 4.64 4.63 4.62 4.61 4.60 VBATT Current(µA) Log Scale 0 -60 0 Reset Threshold vs. Temperature Reset Threshold (V) Resistance (ohms) VBATT=2V 10 -30 Temperature Deg. C 0.9 15 Resistance (ohms) 1.252 VCC to VOUT On Resistance vs. Temperature VBATT to VOUT ON Resistance vs. Temperature VCC=0V VCC=5V VBATT=0 NO LOAD ON PFO 1.254 Temperature Deg. C Temperature Deg. C Resistance (ohms) 1.256 PFI Threshold (V) VCC=5V VBATT=2.8V VBATT Current (µA) VCC Current (µA) 51 47 43 39 35 31 27 23 19 -60 -30 PFI Threshold vs. Temperature Battery Supply Current vs. Temperature (Backup Mode) IE+2 IE+1 IE+0 IE-1 IE-2 IE-3 IE-4 IE-5 IE-6 IE-7 IE-8 VBATT=2.8V .0000 VCC (0.5V/div) 5.000 © Copyright 2000 Sipex Corporation 1000 1000 VBATT=4.5V VCC=0V Slope=5Ω Voltage Drop(mV) Voltage Drop(mV) VCC=4.5V VBATT=0V Slope=0.6Ω 100 10 1 1 10 100 100 10 1 1000 1 10 IOUT (mA) 100 IOUT (mA) Figure 1. VCC to VOUT Vs. Output Current Figure 2. VBATT to VOUT Vs. Output Current VCC VBATT = 0V TA = +25 C VCC VBATT = 0V TA = 25oC 2V div VCC 0V 2KΩ RESET RESET RESET 0V 330pF GND 1sec/div Figure 3A. SP690A RESET Output Voltage vs. Supply Voltage Figure 3B. Circuit for the SP690A/802L RESET Output Voltage vs. Supply Voltage VCC VCC VCC 2V div 0V 5V RESET RESET VBATT 0V 330pF 10KΩ GND 1sec/div Figure 4A. SP805L RESET Output Voltage vs. Supply Voltage SP690A/692ADS/08 Figure 4B. Circuit for the SP805 RESET Output Voltage vs. Supply Voltage SP690A/692A Low Power Microprocessor Supervisory with Battery Switch-Over 6 © Copyright 2000 Sipex Corporation VCC VCC +5V TA = +25 C +4V VCC RESET +5V 10KΩ RESET 0V 30pF GND 2µs/div Figure 5B. Circuit for the SP690A/802L RESET Response Time Figure 5A. SP690A RESET Response Time VCC +5V VCC VCC +4V RESET +4V RESET VBATT 0V 330pF 10KΩ GND 2µs/div Figure 6B. Circuit for the SP805 RESET Response Time Figure 6A. SP805L RESET Response Time +5V VCC = 5V VBATT = 0V +1.3V PFI VCC = +5V TA = +25 C +1.2V 5V 1KΩ PFO PFI 0V +1.25V PFO 30pF 500ns/div Figure 7B. Circuit for the Power-Fail Comparator Response Time (FALL) Figure 7A. Power-Fail Comparator Response Time (FALL) SP690A/692ADS/08 SP690A/692A Low Power Microprocessor Supervisory with Battery Switch-Over 7 © Copyright 2000 Sipex Corporation +1.3V VCC = 5V VBATT = 0V PFI +5V VCC = +5V TA = +25 C +1.2V PFI PFO 3V PFO +1.25V 0V 30pF 1KΩ 2µs/div Figure 8A. Power-Fail Comparator Response Time (RISE) Figure 8B. Circuit for the Power-Fail Comparator Response Time (RISE) +5V VCC 0V +5V RESET* tRS 0V +5V RESET** 3.0V 0V +5V VOUT 3.0V 0V PFO +5V 0V VBATT = PFI = 3.0V *SP690A/692A/802L/802M **SP805L/805M Figure 9. Timing Diagram SP690A/692ADS/08 SP690A/692A Low Power Microprocessor Supervisory with Battery Switch-Over 8 © Copyright 2000 Sipex Corporation FEATURES THEORY OF OPERATION The SP690A/692A/802L/802M/805L/805M provide four key functions: 1. A battery backup switching for CMOS RAM, CMOS microprocessors, or other logic. 2. A reset output during power-up, power-down and brownout conditions. 3. A reset pulse if the optional watchdog timer has not been toggled within a specified time. 4. A 1.25V threshold detector for power-fail warning, low battery detection, or to monitor a power supply other than +5V. The SP690A/692A/802L/802M/805L/805M microprocessor (µP) supervisory circuits monitor the power supplied to digital circuits such as microprocessors, microcontrollers, or memory. The series is an ideal solution for portable, battery-powered equipment that requires power supply monitoring. Implementing this series will reduce the number of components and overall complexity. The watchdog functions of this product family will continuously oversee the operational status of a system. The operational features and benefits of the SP690A/692A/802L/802M/805L/805M are described in more detail below. The parts differ in their reset-voltage threshold levels and reset outputs. The SP690A/802L/ 805L generate a reset when the supply voltage drops below 4.65V. The SP692A/802M/805M generate a reset below 4.40V. Reset Output The microprocessor's (µP's) reset input starts the µP in a known state. When the µP is in an unknown state, it should be held in reset. The SP690A/SP692A/SP802 assert reset during power-up and prevent code execution errors during power-down or brownout conditions. The SP690A/692A/802L/802M/805L/805M are ideally suited for applications in automotive systems, intelligent instruments, and batterypowered computers and controllers. All designs into an environment where it is critical to monitor the power supply to the µP and it’s related digital components will find the SSP690A/692A/802L/802M/805L/805M ideal. On power-up, once VCC reaches 1V, RESET is guaranteed to be a logic low. As VCC rises, RESET remains low. When VCC exceeds the reset threshold, RESET will remain low for 200ms, Figure 9. If a brownout condition occurs and VCC dips below the reset threshold, RESET is triggered. Each time RESET is triggered, it stays low for the reset pulse width interval. If a brownout condition interrupts a previously initiated reset pulse, the reset pulse continues for another 200ms. On power-down, once VCC goes below the threshold, RESET is guaranteed to be logic low until VCC drops below 1V. Regulated +5V Unregulated DC 0.1µF VCC VCC µP RESET NMI PFO I/O LINE WDI GND PFI R2 VOUT VBATT RESET is also triggered by a watchdog timeout. If WDI remains either high or low for a period that exceeds the watchdog timeout period (1.6 sec), RESET pulses low for 200mS. As long as RESET is asserted, the watchdog timer remains clear. When RESET comes high, the watchdog resumes timing and must be serviced within 1.6sec. If WDI is tied high or low, a RESET pulse is triggered every 1.8sec (tWD plus tRS). GND BUS CMOS RAM R1 RESET 3.6V Lithium Battery VCC GND Figure 12. Typical Operating Circuit SP690A/692ADS/08 SP690A/692A Low Power Microprocessor Supervisory with Battery Switch-Over 9 © Copyright 2000 Sipex Corporation Power-Fail Comparator The SP805L/M active-high RESET output is the inverse of the SP690A/SP692A/SP802 RESET output, and is valid with VCC down to 1V. Some µP's, such as Intel's 80C51, require an active-high reset pulse. The Power-Fail Comparator can be used as an under-voltage detector to signal the failing of a power supply (it is completely separate from the rest of the circuitry and does not need to be dedicated to this function). The PFI input is compared to an internal 1.25V reference. If PFI is less than 1.25V, PFO goes low. The external voltage divider drives PFI to sense the unregulated DC input to the +5V regulator. The voltage-divider ratio can be chosen such that the voltage at PFI falls below 1.25V just before the +5V regulator drops out. PFO then triggers an interrupt which signals the µP to prepare for power-down. Watchdog Input The watchdog circuit monitors the µP's activity. If the µP does not toggle the watchdog input (WDI) within 1.6sec, a reset pulse is triggered. The internal 1.6sec timer is cleared by either a reset pulse or by floating the WDI input. As long as RESET is asserted or the WDI input is floating, the timer remains cleared and does not count. As soon as RESET is released and WDI is driven high or low, the timer starts counting. It can detect pulses as short as 50ns. When VBATT connects to VOUT, the power-fail comparator is turned off and PFO is forced low to conserve backup-battery power. Backup-Battery Switchover VBATT SW1 In the event of a brownout or power failure, it may be necessary to preserve the contents of RAM. With a backup battery installed at VBATT, the RAM is assured to have power if VCC fails. As long as VCC exceeds the reset threshold, VOUT connects to VCC through a 0.6Ω PMOS power switch. Once VCC falls below the reset threshold, VCC or VBATT, whichever is higher, switches to VOUT. VBATT connects to VOUT through a 5Ω switch only when VCC is below the reset threshold and VBATT is greater than VCC. VCC D2 D1 SW2 D3 VOUT GND CONDITION SW1 SW2 VCC > Reset Threshold Open Closed VCC < Reset Threshold and VCC > VBATT Open Closed VCC < Reset Threshold and VCC < VBATT Closed Open When VCC exceeds the reset threshold, it is connected to VOUT, regardless of the voltage applied to VBATT Figure 13. During this time, the diode (D1) between VBATT and VOUT will conduct current from VBATT to VOUT if VBATT is more than .6V above VOUT. When VBATT connects to VOUT, backup mode is activated and the internal circuitry will be powered from the battery Figure 14. When VCC is just below VBATT, in the backup mode the current drawn from VBATT will be typically 30µA. When VCC drops to more than 1V below VBATT, the internal switchover comparator shuts off and the supply current falls to less than 0.6µA. Reset Threshold = 4.65V in SP690A/802L/805L Reset Threshold = 4.40V in SP692A/802M/805M Figure 13. BACKUP-BATTERY Switchover Block Diagram SP690A/692ADS/08 SP690A/692A Low Power Microprocessor Supervisory with Battery Switch-Over 10 © Copyright 2000 Sipex Corporation SIGNAL V CC STATUS +5V Disconnected from VOUT VCC Connected to VBATT through VOUT an internal 8Ω PMOS switch Connected to VOUT. Current drawn from the battery is VBATT PFI PFO Logic low RESET Logic low RESET Logic high (SP805 only) WDI GND If VCC is above the reset threshold and VBATT is 0.5V above VCC, current flows to VOUT and VCC from VBATT until the voltage at VBATT is less than 0.5V above VCC. Watchdog timer is disabled Leakage current through the capacitor charging diode and the SP690A/SP802L/SP805L internal power diode eventually discharges the capacitor to VCC. Also, if VCC and VBATT start from 0.5V above the reset threshold and power is lost at VCC, the capacitor on VBATT discharges through VCC until VBATT reaches the reset threshold; the SP690A/SP802L/SP805L then switches to battery-backup mode. Using a High Capacity Capacitor as a Backup Power Source VBATT has the same operating voltage range as VCC, and the battery-switchover threshold voltages are typically +20mV centered at VBATT, allowing use of a capacitor and a simple charging circuit as a backup source (see Figure 16). SP692A SP802M SP805M MAXIMUM BACKUP-BATTERY VOLTAGE [V] +5V VCC VOUT VBATT 4.80 0.1F GND 4.55 CONNECT TO STATIC RAM RESET (RESET)* 100KΩ Figure 15. Allowable BACKUP-BATTERY Voltages SP690A/692ADS/08 *( ) SP805L only Figure 16. Backup Power Source Using High Capacity Capacitor with SP690A/802L/805L and a +5V ±5% Supply Figure 14. Input and Output Status in Battery-Backup Mode. To enter the Battery-Backup mode, VCC must be less than the Reset threshold and less than VBATT. PART NUMBER CONNECT TO µP RESET (RESET)* 0.1F less than 0.6µA, as long as VCC < VBATT - 1V. Power-fail comparator is disabled. SP690A SP802L SP805L CONNECT TO STATIC RAM VOUT VBATT CONNECT TO µP *( ) SP805M only Figure 17. Backup Power Source Using High Capacity Capacitor with SP692A/802M/805M and a +5V ±10% Supply SP690A/692A Low Power Microprocessor Supervisory with Battery Switch-Over 11 © Copyright 2000 Sipex Corporation Operation Without a Backup Power Source +5V VIN VCC If a backup power source is not used, ground VBATT and connect VOUT to VCC. Since there is no need to switch over to any backup power source, VOUT does not need to be switched. A direct connection to VCC eliminates any voltage drops across the switch which may push VOUT below VCC. R1 PFI R2 *C1 R3 PFO *optional connect to µP GND VTRIP = 1.25 R2 = VL - 1.25 + 5.0 - 1.25 R3 R1 The backup battery can be removed while VCC remains valid, without danger of triggering RESET/RESET. As long as VCC stays above the reset threshold, battery-backup mode cannot be entered. 1.25 R2 || R3 R1 + R2 || R3 Adding Hysteresis to the Power-Fail Comparator VH = PFO +5V 0V 0V Replacing the Backup Battery 1.25 R2 R1 + R2 VL VTRIP VH Hysteresis adds a noise margin to the power-fail comparator and prevents repeated triggering of PFO when VIN is close to its trip point. Figure 18 shows how to add hysteresis to the power-fail comparator. Select the ratio of R1 and R2 such that PFI sees 1.25V when VIN falls to its trip point (VTRIP). R3 adds the hysteresis. It will typically be an order of magnitude greater (about 10 times) than R1 or R2. The current through R1 and R2 should be at least 1µA to ensure that the 25nA (max) PFI input current does not shift the trip point. R3 should be larger than 10KΩ so it does not load down the PFO pin. Capacitor C1 adds additional noise rejection. VIN Figure 18. Adding Hysteresis to the POWER-FAIL Comparator Allowable Backup Power-Source Batteries Lithium batteries work very well as backup batteries due to very low self-discharge rate and high energy density. Single lithium batteries with open-circuit voltages of 3.0V to 3.6V are ideal. Any battery with an open-circuit voltage less than the minimum reset threshold plus 0.3V can be connected directly to the VBATT input of this series with no additional circuitry; see FIGURE 12. However, batteries with opencircuit voltages that are greater than this value cannot be used for backup, as current is sourced into VOUT through the diode (D1 in Figure 13) when VCC is close to the reset threshold. SP690A/692ADS/08 Monitoring a Negative Voltage The power-fail comparator can be used to monitor a negative supply rail using the circuit of Figure 19. When the negative rail is valid, PFO is low. When the negative supply voltage drops, PFO goes high. This circuit's accuracy is affected by the PFI threshold tolerance, the VCC voltage, and the resistors, R1 and R2. SP690A/692A Low Power Microprocessor Supervisory with Battery Switch-Over 12 © Copyright 2000 Sipex Corporation +5V Buffered RESET connects to System Components VCC R1 +5V PFI +5V VCC R2 VCC PFO µP V- RESET RESET 4.7KΩ GND 5.0 - 1.25 = 1.25 - VTRIP R2 R1 GND PFO Figure 20. Interfacing to Microprocessors with Bidirectional RESET I/O +5V *VTRIP 0V 0V GND V- *VTRIP is a negative voltage Figure 19. Monitoring a Negative Voltage Interfacing to Microprocessors with Bidirectional Reset Pins Microprocessors with bidirectional reset pins, such as the Motorola 68HC11 series, can contend with this series' RESET output. If, for example, the RESET output is driven high and the µP wants to pull it low, indeterminate logic levels may result. To correct this, connect a 4.7KΩ resistor between the RESET output and the µP reset I/O, as in Figure 20. Buffer the RESET output to other system components. SP690A/692ADS/08 SP690A/692A Low Power Microprocessor Supervisory with Battery Switch-Over 13 © Copyright 2000 Sipex Corporation PACKAGE: PLASTIC DUAL–IN–LINE (NARROW) E1 E D1 = 0.005" min. (0.127 min.) A1 = 0.015" min. (0.381min.) D A = 0.210" max. (5.334 max). C A2 B1 B e = 0.100 BSC (2.540 BSC) Ø L eA = 0.300 BSC (7.620 BSC) ALTERNATE END PINS (BOTH ENDS) DIMENSIONS (Inches) Minimum/Maximum (mm) 8–PIN 14–PIN 16–PIN 18–PIN 20–PIN 22–PIN A2 0.115/0.195 (2.921/4.953) 0.115/0.195 (2.921/4.953) 0.115/0.195 (2.921/4.953) 0.115/0.195 (2.921/4.953) 0.115/0.195 (2.921/4.953) 0.115/0.195 (2.921/4.953) B 0.014/0.022 (0.356/0.559) 0.014/0.022 (0.356/0.559) 0.014/0.022 (0.356/0.559) 0.014/0.022 (0.356/0.559) 0.014/0.022 (0.356/0.559) 0.014/0.022 (0.356/0.559) B1 0.045/0.070 (1.143/1.778) 0.045/0.070 (1.143/1.778) 0.045/0.070 (1.143/1.778) 0.045/0.070 (1.143/1.778) 0.045/0.070 (1.143/1.778) 0.045/0.070 (1.143/1.778) C 0.008/0.014 (0.203/0.356) 0.008/0.014 (0.203/0.356) 0.008/0.014 (0.203/0.356) 0.008/0.014 (0.203/0.356) 0.008/0.014 (0.203/0.356) 0.008/0.014 (0.203/0.356) D 0.355/0.400 0.735/0.775 0.780/0.800 0.880/0.920 0.980/1.060 1.145/1.155 (9.017/10.160) (18.669/19.685) (19.812/20.320) (22.352/23.368) (24.892/26.924) (29.083/29.337) E 0.300/0.325 (7.620/8.255) 0.300/0.325 (7.620/8.255) 0.300/0.325 (7.620/8.255) 0.300/0.325 (7.620/8.255) 0.300/0.325 (7.620/8.255) 0.300/0.325 (7.620/8.255) E1 0.240/0.280 (6.096/7.112) 0.240/0.280 (6.096/7.112) 0.240/0.280 (6.096/7.112) 0.240/0.280 (6.096/7.112) 0.240/0.280 (6.096/7.112) 0.240/0.280 (6.096/7.112) L 0.115/0.150 (2.921/3.810) 0.115/0.150 (2.921/3.810) 0.115/0.150 (2.921/3.810) 0.115/0.150 (2.921/3.810) 0.115/0.150 (2.921/3.810) 0.115/0.150 (2.921/3.810) Ø 0°/ 15° (0°/15°) 0°/ 15° (0°/15°) 0°/ 15° (0°/15°) 0°/ 15° (0°/15°) 0°/ 15° (0°/15°) 0°/ 15° (0°/15°) SP690A/692ADS/08 SP690A/692A Low Power Microprocessor Supervisory with Battery Switch-Over 14 © Copyright 2000 Sipex Corporation PACKAGE: PLASTIC SMALL OUTLINE (SOIC) (NARROW) E H h x 45° D A Ø e B DIMENSIONS (Inches) Minimum/Maximum (mm) A1 L 8–PIN 14–PIN 16–PIN A 0.053/0.069 (1.346/1.748) 0.053/0.069 (1.346/1.748) 0.053/0.069 (1.346/1.748) A1 0.004/0.010 (0.102/0.249 0.004/0.010 (0.102/0.249) 0.004/0.010 (0.102/0.249) B 0.014/0.019 (0.35/0.49) 0.013/0.020 (0.330/0.508) 0.013/0.020 (0.330/0.508) D 0.189/0.197 (4.80/5.00) 0.337/0.344 0.386/0.394 (8.552/8.748) (9.802/10.000) E 0.150/0.157 (3.802/3.988) 0.150/0.157 (3.802/3.988) 0.150/0.157 (3.802/3.988) e 0.050 BSC (1.270 BSC) 0.050 BSC (1.270 BSC) 0.050 BSC (1.270 BSC) H 0.228/0.244 (5.801/6.198) 0.228/0.244 (5.801/6.198) 0.228/0.244 (5.801/6.198) h 0.010/0.020 (0.254/0.498) 0.010/0.020 (0.254/0.498) 0.010/0.020 (0.254/0.498) L 0.016/0.050 (0.406/1.270) 0.016/0.050 (0.406/1.270) 0.016/0.050 (0.406/1.270) Ø 0°/8° (0°/8°) 0°/8° (0°/8°) 0°/8° (0°/8°) SP690A/692ADS/08 SP690A/692A Low Power Microprocessor Supervisory with Battery Switch-Over 15 © Copyright 2000 Sipex Corporation ORDERING INFORMATION Model Temperature Range Package Types SP690ACN..........................................................0°C to +70°C....................................................8-Pin NSOIC SP690ACP........................................................0°C to +70°C.........................................................8-Pin PDIP SP690AEN......................................................-40°C to +85°C.....................................................8-Pin NSOIC SP690AEP.......................................................-40°C to +85°C.......................................................8-Pin PDIP SP692ACN........................................................0°C to +70°C......................................................8-Pin NSOIC SP692ACP........................................................0°C to +70°C.........................................................8-Pin PDIP SP692AEN......................................................-40°C to +85°C.....................................................8-Pin NSOIC SP692AEP.......................................................-40°C to +85°C.......................................................8-Pin PDIP SP802LCN........................................................0°C to +70°C......................................................8-Pin NSOIC SP802LCP........................................................0°C to +70°C.........................................................8-Pin PDIP SP802LEN.......................................................-40°C to +85°C....................................................8-Pin NSOIC SP802LEP.......................................................-40°C to +85°C.......................................................8-Pin PDIP SP802MCN.......................................................0°C to +70°C......................................................8-Pin NSOIC SP802MCP.......................................................0°C to +70°C.........................................................8-Pin PDIP SP802MEN......................................................-40°C to +85°C....................................................8-Pin NSOIC SP802MEP......................................................-40°C to +85°C.......................................................8-Pin PDIP SP805LCN........................................................0°C to +70°C......................................................8-Pin NSOIC SP805LCP........................................................0°C to +70°C.........................................................8-Pin PDIP SP805LEN.......................................................-40°C to +85°C....................................................8-Pin NSOIC SP805LEP.......................................................-40°C to +85°C.......................................................8-Pin PDIP SP805MCN.......................................................0°C to +70°C......................................................8-Pin NSOIC SP805MCP.......................................................0°C to +70°C.........................................................8-Pin PDIP SP805MEN......................................................-40°C to +85°C....................................................8-Pin NSOIC SP805MEP......................................................-40°C to +85°C.......................................................8-Pin PDIP Please consult the factory for pricing and availability on a Tape-On-Reel option. Corporation SIGNAL PROCESSING EXCELLENCE Sipex Corporation Headquarters and Sales Office 22 Linnell Circle Billerica, MA 01821 TEL: (978) 667-8700 FAX: (978) 670-9001 e-mail: [email protected] Sales Office 233 South Hillview Drive Milpitas, CA 95035 TEL: (408) 934-7500 FAX: (408) 935-7600 Sipex Corporation reserves the right to make changes to any products described herein. Sipex does not assume any liability arising out of the application or use of any product or circuit described hereing; neither does it convey any license under its patent rights nor the rights of others. SP690A/692ADS/08 SP690A/692A Low Power Microprocessor Supervisory with Battery Switch-Over 16 © Copyright 2000 Sipex Corporation