CXD3059AR CD Digital Signal Processor with Built-in RF Amplifier and Digital Servo + Digital High & Bass Boost Description The CXD3059AR is a digital signal processor LSI for CD players. This LSI incorporates a RF amplifier and digital servo, high & bass boost, 1-bit DAC and analog low-pass filter. 120 pin LQFP (Plastic) Features • All digital signal processing during playback is performed with a single chip • Highly integrated mounting possible due to a built-in RF amplifier RF Block • Supports 4× speed playback CD • RF system equalizer • Supports pickup built-in RF summing amplifier • Gain level switch • TE balance adjustment function Digital Signal Processor (DSP) Block • Supports CAV (Constant Angular Velocity) playback • Frame jitter free • 0.5× to 4× speed continuous playback possible • Allows relative rotational velocity readout • Supports variable pitch playback • The bit clock, which strobes the EFM signal, is generated by the digital PLL. • EFM data demodulation • Enhanced EFM frame sync signal protection • Refined super strategy-based powerful error correction C1: double correction, C2: quadruple correction Supported during 4× speed playback • Noise reduction during track jumps • Auto zero-cross mute • Subcode demodulation and subcode-Q data error detection • Digital spindle servo • 16-bit traverse counter • Asymmetry correction circuit • CPU interface on serial bus • Error correction monitor signal, etc. output from CPU interface • Servo auto sequencer • Fine search performs track jumps with high accuracy • Digital audio interface outputs • Digital level meter, peak meter • Bilingual compatible • VCO control mode • CD TEXT data demodulation Digital Servo (DSSP) Block • Microcomputer software-based flexible servo control • Offset cancel function for servo error signal • Auto gain control function for servo loop • E:F balance, focus bias adjustment functions • Surf jump function supporting micro two-axis • Tracking filter: 6 stages, Focus filter: 5 stages • Digital dynamics (compressor) Volume increased by +5dB at low level • 8× oversampling digital filter (attenuation: 61dB, ripple within band: ±0.0075dB) • Digital signal output possible after boost • Serial data format selectable from (output) 20 bits/18 bits/16 bits (rearward truncation, MSB first) • Digital attenuation: –∞, –60 to +6dB, 2048 steps (linear) • Soft mute • Digital de-emphasis • High-cut filter Applications CD players Structure Silicon gate CMOS IC Absolute Maximum • Supply voltage 1 • Input voltage 1 • Output voltage 1 • Supply voltage 2 • • • • Ratings (Ta = 25°C) VDD, XVDD VSS – 0.5 to +3.5 V VSS – 0.3 to VDD + 0.3 V V I1 VO1 VSS – 0.3 to VDD + 0.3 V IOVDD0 to 2, AVDD0 to 5 IOVSS – 0.5 to +4.5 V Input voltage 2 V I2 IOVSS – 0.3 to IOVDD + 0.3 V IOVSS – 0.3 to IOVDD + 0.3 V Output voltage 2 VO2 Storage temperature Tstg –55 to +150 °C Supply voltage difference IOVSS, AVSS, XVSS – VSS –0.3 to +0.3 V –0.3 to +0.3 V XVDD – VDD IOVDD, AVDD, XVDD – VDD –0.3 to +0.3 V (IOVDD, AVDD, XVDD < 2.3V) Recommended Operating Conditions 2.5 ± 0.2 • Supply voltage 1 VDD, XVDD • Supply voltage 2 IOVDD0 to 2, AVDD0 to 5 3.3 ± 0.3 • Operating temperature Topr –20 to +75 Digital Filter, DAC and Analog Low-pass Filter Blocks • Digital dynamic bass boost and high boost Bass Boost: 4th-order IIR 24dB/Oct +10dB/+14dB/+18dB/+22dB High Boost: Second-order IIR 12dB/Oct +4dB/+6dB/+8dB/+10dB • Independent turnover frequency selection possible Bass Boost: 125Hz/160Hz/200Hz High Boost: 5kHz/7kHz I/O Pin Capacitance • Input capacitance CI • Output capacitance CO • I/O capacitance CI/O Note) Measurement conditions 7 (Max.) 7 (Max.) 7 (Max.) VDD = VI = 0V fM = 1MHz V V °C pF pF pF Sony reserves the right to change products and specifications without prior notice. This information does not convey any license by any implication or otherwise under any patents or other right. Application circuits shown, if any, are typical examples illustrating the operation of the devices. Sony cannot assume responsibility for any problems arising out of the use of these circuits. –1– E03736-PS CXD3059AR SERVO Block MIRR DFCT FOK SYSM SQSO SQCK SBSO EXCK DATA XLAT CLOK SENS SCOR C2PO WDCK EMPH WFCK XUGF GFS SCLK ATSK SSTP COUT Block Diagram CPU Interface SERVO Interface Bass Boost Block LMUT MIRR DFCT FOK RMUT LPF LOCK MDP LPF DAC SFDR SRDR AOUT2 VREFR VREL AOUT1 EMPHI TFDR PWM Generator TRDR LRCKI PCMDI FFDR BCKI FRDR XTACN SERVO DSP XTSL CD Signal Prosessor Block TEI A/D Converter FEI Clock Generator XTAI XTAO VCTL Servo Auto Sequencer VPCO Digital OUT Digital CLV DOUT BCK Selector D/A Interface TEO PCMD LRCK TE E Error Corrector F 32K RAM XRST TES1 FEO FE TEST EFM Demodulator AVDD0 to 5 Sub Code Processor A B AVSS0 to 5 IOVDD0 to 2 SUM C RFamp Block IOVSS0 to 2 Asymmetry Corrector D VC Digital PLL DC/DC Convertor VSS –2– DDCR DDVRSEN DDVROUT XPCK PCO FILI FIFO CLTV ASYO RFACO ASYI AMP BIAS EQ RFACI ATT RFC AC_SUM RFDCO LD PD APC EQ_IN VC PDSENS VDD CXD3059AR PCMDI LRCKI LRCK VSS PCMD BCK VDD EMPH EMPHI IOVDD2 DOUT TEST IOVSS2 TES1 NC XVSS XTAO XTAI AVDD1 XVDD AOUT1 VREFL AVSS1 AVSS2 VREFR AOUT2 AVDD2 IOVDD0 NC RMUT Pin Configuration 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 LMUT 91 60 BCKI NC 92 59 NC XTSL 93 58 DDCR IOVSS0 94 57 AVSS5 XTACN 95 56 DDVRSEN SQSO 96 55 DDVROUT SQCK 97 54 AVDD5 SBSO 98 53 PCO EXCK 99 52 FILI XRST 100 51 FILO SYSM 101 50 CLTV DATA 102 49 AVSS3 103 48 VCTL XLAT 104 47 VPCO CLOK 105 46 ASYO VSS VDD 106 45 ASYI SENS 107 44 BIAS SCLK 108 43 AVDD3 ATSK 109 42 RFACI WFCK 110 41 RFACO XUGF 111 40 AVSS4 XPCK 112 39 RFC GFS 113 38 NC C2PO 114 37 PD SCOR 115 36 LD VDD 116 35 EQ_IN C4M 117 34 AC_SUM WDCK 118 33 PDSENS COUT 119 32 RFDCO NC 120 NC D C B A SFDR VC IOVSS1 FEO SSTP FEI MDP TEO LOCK TEI VSS F FOK E MIRR –3– NC 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 AVSS0 8 AVDD0 7 FRDR 6 IOVDD1 5 FFDR 4 TRDR 3 TFDR 2 SRDR 1 DFCT 31 AVDD4 CXD3059AR Pin Description Power supply Pin No. Symbol I/O Description 1 MIRR I/O 1, 0 Mirror signal input/output. 2 DFCT I/O 1, 0 Defect signal input/output. 3 FOK I/O 1, 0 Focus OK signal input/output. 4 VSS — — 5 LOCK I/O 1, 0 6 MDP O 1, Z, 0 Spindle motor servo control output. 7 SSTP I 8 IOVSS1 — — 9 SFDR O 1, 0 Sled drive output. 10 SRDR O 1, 0 Sled drive output. 11 TFDR O 1, 0 Tracking drive output. 12 TRDR O 1, 0 Tracking drive output. 13 FFDR O 1, 0 Focus drive output. 14 FRDR O 1, 0 Focus drive output. 15 IOVDD1 — — I/O digital power supply. A/D 3.3V 16 AVDD0 — — Analog power supply. 17 AVSS0 — — Analog GND. — 18 NC — — 19 E I E signal input. 20 F I F signal input. 21 TEI I Tracking error signal input to DSSP block. 22 TEO O Tracking error signal output from RF amplifier block. 23 FEI I Focus error signal input to DSSP block. 24 FEO O Focus error signal output from RF amplifier block. 25 VC I/O Center voltage output from RF amplifier block. Center voltage input to DSSP block by command switch. 26 A I A signal input. 27 B I B signal input. 28 C I C signal input. 29 D I D signal input. 30 NC — — 31 AVDD4 — — 32 RFDCO I/O 33 PDSENS I 34 AC_SUM O Analog RFAC summing amplifier output. Digital I/O = 3.3V Internal = 2.5V RFamp 3.3V Internal digital GND. GFS is sampled at 460Hz; when GFS is high , this pin outputs a high signal. If GFS is low eight consecutive samples, this pin outputs low. Or this pin inputs when LKIN = "1". Disk innermost detection signal input. I/O digital GND. Analog power supply. RFDC signal output. RFDC signal input to DSSP block by command switch. Reference voltage pin for PD. –4– CXD3059AR Power supply RFamp 3.3V ASYM 3.3V DC/DC 3.3V — Digital I/O = 3.3V Internal = 2.5V Pin No. Symbol 35 EQ_IN I Equalizer circuit input. 36 LD O APC amplifier output. 37 PD I APC amplifier input. 38 NC — 39 RFC 40 AVSS4 — 41 RFACO O RFAC signal output. 42 RFACI I RFAC signal input or EFM signal input. 43 AVDD3 — 44 BIAS I Asymmetry circuit constant current input. 45 ASYI I Asymmetry comparator voltage input. 46 ASYO O 47 VPCO O 1, Z, 0 Wide-band EFM PLL charge pump output. 48 VCTL I 49 AVSS3 — 50 CLTV I 51 FILO O Analog Master PLL (slave = digital PLL) filter output. 52 FILI I 53 PCO O 1, Z, 0 Master PLL charge pump output. 54 AVDD5 — 55 DDVROUT O DC/DC converter output. Leave open when not using. 56 DDVRSEN I DC/DC converter output voltage monitor pin. Connect to analog power supply when not using. 57 AVSS5 — 58 DDCR I 59 NC 60 BCKI I D/A interface bit clock input. 61 PCMDI I D/A interface serial data input. (2's COMP, MSB first) 62 LRCKl I D/A interface LR clock input. 63 LRCK O 1, 0 64 VSS — — 65 PCMD O 1, 0 D/A interface serial data output. (2's COMP, MSB first) 66 BCK O 1, 0 D/A interface bit clock output. 67 VDD — — Internal digital power supply. 68 EMPH O 1, 0 69 EMPHI I I/O — I — Description Equalizer cut-off frequency adjustment pin. — — 1, 0 Analog GND. Analog power supply. EFM full-swing output. (Low = VSS, High = VDD) Wide-band EFM PLL VCO2 control voltage input. — Analog GND. Multiplier VCO1 control voltage input. Master PLL filter input. — — Analog power supply. Analog GND. DC/DC converter reset pin. — D/A interface LR clock output. f = Fs Internal digital GND. High when the playback disc has emphasis, low it has not. High when de-emphasis is ON, low when input OFF. –5– CXD3059AR Power supply Digital I/O = 3.3V Internal = 2.5V — X'tal 2.5V Lch 3.3V Rch 3.3V — Digital I/O = 3.3V Internal = 2.5V Pin No. Symbol 70 IOVDD2 — — 71 DOUT O 1, 0 72 TEST I Test pin. Normally GND. 73 TES1 I Test pin. Normally GND. 74 IOVss2 — — 75 NC — — 76 XVSS — — 77 XTAO O Crystal oscillation circuit output. 78 XTAI I Crystal oscillation circuit input. 79 XVDD — — Master clock power supply. 80 AVDD1 — — Analog power supply. 81 AOUT1 O Lch analog output. 82 VREFL O Lch reference voltage. 83 AVSS1 — — Analog GND. 84 AVSS2 — — Analog GND. 85 VREFR O Rch reference voltage. 86 AOUT2 O Rch analog output. 87 AVDD2 — — 88 NC — — 89 IOVDD0 — — 90 RMUT O 1, 0 Rch "0" detection flag. 91 LMUT O 1, 0 Lch "0" detection flag. 92 NC — — 93 XTSL 94 IOVSS0 — 95 XTACN I 96 SQSO O 97 SQCK I 98 SBSO O 99 EXCK I SBSO readout clock input. 100 XRST I System reset. Reset when low. 101 SYSM I Mute input. Muted when high. 102 D ATA I Serial data input from CPU. 103 VSS 104 XLAT I/O I I/O digital power supply. Digital Out output. I/O digital GND. Master clock GND. Analog power supply. I/O digital power supply. Crystal selection input. Low when the crystal is 16.9344MHz; high when the crystal is 33.8688MHz. I — Description — I/O digital GND. Oscillation circuit control. Self-oscillation when high, oscillation stop when low. 1, 0 Subcode Q 80-bit and PCM peak and level data output. CD TEXT data output. SQSO readout clock input. 1, 0 — Subcode P to W serial output. Internal digital GND. Latch input from CPU. The serial data is latched at the falling edge. –6– CXD3059AR Power supply Pin No. Symbol 105 CLOK I/O I Description Serial data transfer clock input from CPU. 106 VDD — — 107 SENS O 1, 0 108 SCLK I 109 ATSK I/O 1, 0 Anti-shock input/output. 110 WFCK O 1, 0 WFCK output. 111 XUGF O 1, 0 XUGF output. Output MNT0, RFCK, SOUT by command switch. 112 XPCK O 1, 0 XPCK output. Output MNT1, SOCK by command switch. O 1, 0 GFS output. Output MNT2, XROF, XOLT by command switch. O 1, 0 C2PO output. Output MNT3, GTOP by command switch. 115 SCOR O 1, 0 High output when the subcode sync, S0 or S1, is detected. 116 VDD — — 117 C4M O 1, 0 4.2336MHz output. 1/4 frequency-division output of the V16M in CAV-W mode and variable pitch mode. 118 WDCK O 1, 0 Word clock output. f = 2Fs. GRSCOR output by command switch. 119 COUT I/O 1, 0 Track number count signal input/output. 120 NC — — Digital I/O = 3.3V 113 GFS Internal = 2.5V 114 C2PO Internal digital power supply. SENS output to CPU. SENS serial data readout clock input. Internal digital power supply. Notes) • PCMD is a MSB first, two's complement output. • GTOP is used to monitor the frame sync protection status. (High: sync protection window released.) • XUGF is the frame sync obtained from the EFM signal, and is negative pulse. It is the signal before sync protection. • XPCK is the inverse of the EFM PLL clock. The PLL is designed so that the falling edge and the EFM signal transition point coincide. • The GFS signal goes high when the frame sync and the insertion protection timing match. • RFCK is derived from the crystal accuracy, and has a cycle of 136µs. • C2PO represents the data error status. • XROF is generated when the 32K RAM exceeds the ±28 frame jitter margin. • C4M is a 4.2336MHz output that changes in CAV-W mode and variable pitch mode. • FSTO is the 2/3 frequency-division output of the XTAI pin. • SOUT is the serial data output inside the servo block. • SOCK is the serial data readout clock output inside the servo block. • XOLT is the serial data latch output inside the servo block. –7– CXD3059AR Monitor Pin Output Combinations Command bit Output data SRO1 MTSL1 MTSL0 0 0 0 XUGF XPCK GFS C2PO 0 0 1 MNT0 MNT1 MNT2 MNT3 0 1 0 RFCK XPCK XROF GTOP 0 1 1 C4M GSTO GFS C2PO 1 0 0 SOUT SOCK XOLT C2PO Reset Timing when Power on Power on with XRST pin low. Set XRST pin high after holding it low 100ns or more to cancel reset. –8– CXD3059AR RF Block Pin Equivalent Circuit Pin No. 19 Symbol E I/O I Equivalent circuit Description 19 VC Tracking error amplifier input. 20 F I 20 VC 21 TEI I 22 TEO O Tracking error signal input to DSSP block. 21 1pF Tracking error amplifier output. 22 23 FEI I 24 FEO O Focus error signal input to DSSP block. 23 1pF Focus error amplifier output. 24 25 VC I/O (AVDD4 – AVSS4)/2 voltage output. 25 –9– CXD3059AR Pin No. 26 Symbol A I/O Equivalent circuit Description I 15kΩ 26 27 B I 27 RF summing amplifier and focus error amplifier input. 30kΩ 28 C I 28 30kΩ 29 29 D I 30 NC — — 31 AVDD4 — — — Analog power supply. 10kΩ 32 RFDCO I/O RFDC amplifier output. 0.5pF 100Ω 32 33 PDSENS I 34 AC_SUM O 10kΩ 59kΩ 33 34 – 10 – APC amplifier reference voltage (GND signal) input. RFAC summing amplifier output. CXD3059AR Pin No. Symbol I/O Equivalent circuit Description 35 4kΩ 35 EQ_IN I Equalizer circuit input. 4kΩ 4kΩ 4kΩ VC 36 LD 57kΩ O APC amplifier output. 10kΩ 500Ω 36 37 PD I 38 NC — 1kΩ APC amplifier input. 37 — — 39 39 RFC 40 AVSS4 — 41 RFACO O Equalizer cut-off frequency adjustment. I — Analog GND. 25Ω VC 41 – 11 – RFAC amplifier output. CXD3059AR Electrical Characteristics 1. DC Characteristics (VDD = XVDD = 2.5 ± 0.2V, IOVDD0 to 2 = AVDD0 to 5 = 3.3 ± 0.3V, VSS = XVSS = IOVSS = AVSS = 0V, Topr = –20 to +75°C) Item Input voltage (1) Input voltage (2) Input voltage (3) Output voltage (1) Output voltage (2) Output voltage (3) Output voltage (4) Conditions High level input voltage VIH (1) Low level input voltage VIL (1) High level input voltage VIH (2) Low level input voltage VIL (2) Hysteresis Vt+ – Vt– Input voltage VIN (3) Min. Typ. Unit Applicable pins V ∗1, ∗3, ∗9 0.2VDD V ∗2 VDD V ∗4, ∗12 V ∗5, ∗8, ∗9 V ∗6 V ∗7 V ∗11 10 µA ∗1, ∗2, ∗9 240 µA ∗3 10 µA ∗8 Max. 0.7VDD 0.2VDD 0.7VDD Schmitt input 0.5 Analog input VSS High level VOH (1) output voltage IOH = –2.4mA VDD – 0.4 Low level VOL (1) output voltage IOL = 4mA High level VOH (2) output voltage IOH = –1.2mA Low level VOL (2) output voltage IOL = 2mA High level VOH (3) output voltage IOH = –2.4, –4.8, –7.2, –9.6mA Low level VOL (3) output voltage IOL = 4, 8, 12, 16mA High level VOH (4) output voltage IOH = –0.28mA Low level VOL (4) output voltage IOL = 0.36mA 0.4 VDD – 0.4 0.4 VDD – 0.4 0.4 VDD – 0.4 0.4 Input leak current II VIN = VSS or VDD –10 Input leak current (with pull-down resistor) IIH VIN = VDD 40 Tri-state output leak current (when high impedance) IOZ VIN = VSS or VDD –10 – 12 – 100 CXD3059AR Applicable pins ∗1 PCMDI, EMPHI, TEST, TES1, XTSL, XTACN, SYSM, DATA ∗2 BCKI, LRCKI, SQCK, EXCK, XRST, XLAT, CLOK, SCLK ∗3 SSTP ∗4 E, F, TEI, FEI, A, B, C, D, PDSENS, EQ_IN, PD, RFC, RFACI, BIAS, ASYI, VCTL, CLTV, FILI, DDVRSEN, DDCR ∗5 SFDR, SRDR, TFDR, TRDR, FFDR, FRDR, LRCK, PCMD, BCK, EMPH, RMUT, LMUT, SQSO, SBSO, WFCK, XUGF, XPCK, GFS, C2PO, SCOR, C4M, WDCK ∗6 ASYO ∗7 DOUT ∗8 MDP, VPCO, PCO, SENS ∗9 MIRR, DFCT, FOK, LOCK, ATSK, COUT ∗10 TEO, FEO, AC_SUM, LD, RFACO, DDVROUT, AOUT1, VREFL, VREFR, AOUT2 ∗11 FILO ∗12 VC, RFDCO – 13 – CXD3059AR 2. AC Characteristics (1) XTAI pin (a) When using self-oscillation (VDD = XVDD = 2.5 ± 0.2V, IOVDD0 to 2 = AVDD0 to 5 = 3.3 ± 0.3V, VSS = XVSS = IOVSS = AVSS = 0V, Topr = –20 to +75°C) Item Oscillation frequency Symbol fMAX Conditions Min. Typ. Max. XTSL = L, $AEXX1 CKSL (1, 0) = 00 16.8 16.9344 17.1 XTSL = H, $AEXX1 CKSL (1, 0) = 00 33.5 33.8688 34.2 XTSL = H, $AEXX1 CKSL (1, 0) = 01 or 10 or 11 67.1 67.7376 68.4 (b) When inputting pulses to XTAI pin (VDD = XVDD = 2.5 ± 0.2V, IOVDD0 to 2 = AVDD0 to 5 = 3.3 ± 0.3V, VSS = XVSS = IOVSS = AVSS = 0V, Topr = –20 to +75°C) Item Symbol Min. High level pulse width tWHX Low level pulse width Max. Unit 6.6 32.7 ns tWLX 6.6 32.7 ns Pulse cycle tCX 14.6 59.5 ns Input high level VIHX 1.7 Input low level VILX Rise time, fall time tR , t F 0 Typ. V 0.7 V 10 ns tCX tWLX tWHX VIHX VIHX × 0.9 XTAI VDD/2 VIHX × 0.1 VILX tR tF Note) When the pulse is input to the XTAI pin, be sure to input it via the capacitor. – 14 – Unit MHz CXD3059AR (2) CLOK, DATA, XLAT, SQCK and EXCK pins (VDD = XVDD = 2.5 ± 0.2V, IOVDD0 to 2 = AVDD0 to 5 = 3.3 ± 0.3V, VSS = XVSS = IOVSS = AVSS = 0V, Topr = –20 to +75°C) Symbol Item Min. Typ. Max. Unit 16 MHz 30000 ns Clock frequency fCK Clock pulse width tWCK 62.5 Setup time tSU 300 ns Hold time tH 300 ns Delay time tD 300 Latch pulse width tWL 750 EXCK frequency fT EXCK pulse width tWT SQCK frequency fT SQCK pulse width tWT COUT frequency (during input)∗ fT COUT pulse width (during input)∗ fWT 30000 ns 0.65 750 750 7.5 tWCK CLOK DATA tWSC tSU tH tD tWL EXCK SQCK COUT tWT tWT 1/fT SBSO SQSO tSU tH – 15 – 0.65 MHz 120000 ns 65 kHz µs 1/fCK XLAT MHz ns ∗ Only when $44 and $45 are executed. tWCK ns CXD3059AR (3) SCLK pin XLAT tDLS tSPW ... SCLK 1/fSCLK Serial Read Out Data (SENS) ... MSB LSB (VDD = XVDD = 2.5 ± 0.2V, IOVDD0 to 2 = AVDD0 to 5 = 3.3 ± 0.3V, VSS = XVSS = IOVSS = AVSS = 0V, Topr = –20 to +75°C) Symbol Item Min. Typ. Max. Unit 16 MHz SCLK frequency fSCLK SCLK pulse width tSPW 31.3 ns Delay time tDLS 15 µs (4) COUT, MIRR and DFCT pins Operating frequency (VDD = XVDD = 2.5 ± 0.2V, IOVDD0 to 2 = AVDD0 to 5 = 3.3 ± 0.3V, VSS = XVSS = IOVSS = AVSS = 0V, Topr = –20 to +75°C) Item Symbol Min. Typ. Max. Unit Conditions COUT maximum operation frequency fCOUT 40 kHz ∗1 MIRR maximum operation frequency fMIRR 40 kHz ∗2 DFCT maximum operation frequency fDFCTH 5 kHz ∗3 ∗1 When using a high-speed traverse TZC ∗2 B A When the RF signal continuously satisfies the following conditions during the traverse. • A = 0.11VDD to 0.23VDD • B ≤ 25% A+B ∗3 During complete RF signal omission. When settings related to DFCT signal generation are Typ. – 16 – CXD3059AR 1-bit DAC and LPF Block Analog Characteristics (VDD = XVDD = 2.5V, IOVDD0 to 2 = AVDD0 to 5 = 3.3V, VSS = XVSS = IOVSS = AVSS = 0V, Topr = +25°C) Symbol Item Conditions Min. Total harmonic distortion THD 1kHz sine wave, 0dB data, 20kHz LPF Signal-to-noise ratio S/N 1kHz sine wave, 0dB data, AMUT OFF (Using A-weighting filter 20kHz LPF) Typ. Max. 0.006 0.014 90 95 Fs = 44.1kHz in all cases. The total harmonic distortion and signal-to-noise ratio measurement circuits are shown below. 22µF 100Ω AOUT1 (2) Audio Analyzer 2200pF 100kΩ VREFL (R) 1µF LPF external circuit diagram DATA Rch A Lch B RF CXD3059AR TEST DISC Audio Analyzer Block diagram of analog characteristics measurement (VDD = XVDD = 2.5V, IOVDD0 to 2 = AVDD0 to 5 = 3.3V, VSS = XVSS = IOVSS = AVSS = 0V, Topr = +25°C) Item Symbol Min. Typ. Output voltage VOUT 920 928 Load resistance RL 10 VREF pin capacitance CVREF 1 Max. Unit Applicable pins ∗1 mVrms ∗1 kΩ µF ∗2 ∗ Measurement is conducted for the above circuit diagrams with the sine wave output of 1kHz and 0dB. Applicable pins ∗1 AOUT1, AOUT2 ∗2 VREFL, VREFR – 17 – Unit % dB RF Block Electrical Characteristics (VDD = XVDD = 2.5V, IOVDD0 to 2 = AVDD0 to 5 = 3.3V, VSS = XVSS = IOVSS = AVSS = 0V, Topr = +25°C) Bias conditions Measurement item Symbol Input impedance (A, B, C and D) RA,B,C,D Input impedance (E and F) RE,F Input impedance (PD) RPD RF block current consumption (on operation) IAVD SW conditions Sending command AC input AC input DC input amplitude frequency voltage DC input current VDD AVDD Connect to VC except measurement pins. 2.5V 3.3V $3AF100 Min. Typ. Max. Unit Pin current A, B, C, D 10 15 20 kΩ Pin current E, F 21 30 39 kΩ Pin current PD 10 Pin current AVDD4 Pin current AVDD4 MΩ 40 70 mA 1 mA ISTB VC 2.5V 3.3V RF block current consumption (on standby) Output voltage VVC ±3mA Input voltage VPD 0 PD input voltage which LD, PD LD pin voltage is 1.41V Output voltage (on standby) VLDstb 0 Pin voltage LD AVDD – 0.2 0 Pin voltage LD 1.89 2.14 2.39 V APC – 18 – Measurement pins Measurement conditions $ADF7CC00 $AD000800 2.5V 3.3V Pin voltage VC 0.5AVDD – 0.1 0.5AVDD 0.5AVDD + 0.1 V 100 150 200 mV V VPDT VPD + 12mV VPDB VPD – 12mV 0 Pin voltage LD 0.43 0.68 0.93 V Input voltage range 2.5V 3.3V ILD 0 1mA Pin voltage LD 0.34 0.64 0.94 V Output impedance RLD VPD 1mA Pin voltage LD 1.66 1.91 2.16 V CXD3059AR Maximum output current Bias conditions Symbol Input voltage range VIR-ACSUM Output voltage range VOR-ACSUM ACSUM Measurement item SW conditions Sending command Input conversion VOF-ACSUM DC offset voltage $3AA000 Input conversion VDF-ACSUM DC offset temperature drift $3AA01C Offset voltage AC input AC input DC input amplitude frequency voltage 2.5V – 19 – Frequency FSUM2 characteristics 2 Measurement conditions Measurement pins Min. Pin voltage, A+B+C+D RFDC Pin voltage Pin voltage $3AA004 $3AA018 Max. Unit 0.5AVDD – 0.1 0.9AVDD + 0.1 V RFDC 0.47AVDD 0.65AVDD V RFDC 0.5AVDD – 0.23 0.5AVDD + 0.23 V RFDC 61mVp-p VC + VAC1/2 Typ. µV/ °C ±6 3V Pin voltage 0.2/6MHz RFDC VDD AVDD VOFFSUM Frequency FSUM1 characteristics 1 20 log (V6M/V0.2M) 0.7 0.9 1.1 V –4 0 1 dB –4 0 1 dB 3 % RFDC 104mVp-p (V6M/V3M) × 100 RFDC VIR-RFDC Pin voltage, A+B+C+D RFDC 0.3AVDD – 0.1 0.7AVDD + 0.1 V VOR-RFDC Pin voltage RFDC 0.25AVDD 0.75AVDD V Pin voltage RFDC 0.3AVDD – 0.23 0.3AVDD + 0.23 V Distortion rate DSUM Input voltage range Output voltage range 600mVp-p Input conversion VOF-RFDC DC offset voltage $3AA000 Input conversion VDF-RFDC DC offset temperature drift $3AA01C Frequency FRFDC1 characteristics 1 $3AA004 3MHz Frequency FRFDC2 characteristics 2 3V 61mVp-p VC + VAC1/2 20 log (V6M/V0.2M) 100kHz –4 0 1 dB –4 0 1 dB RFDC 104mVp-p 1.5Vp-p µV/ °C ±6 RFDC 0.1 % CXD3059AR DRFDC $3AA018 VC + VAC1/2 2.5V 0.2/6MHz Distortion rate DC input current Bias conditions FE Measurement item SW conditions Sending command AC input AC input DC input amplitude frequency voltage DC input current VDD AVDD Measurement conditions Measurement pins Min. Typ. Max. Unit Input voltage range VIR-FE VC reference about (B + D) and (A + C) FE 0.375 AVDD 0.625 AVDD V Output voltage range VOR-FE Pin voltage FE 0.5 AVDD – 0.5 V Input conversion VOF-FE DC offset voltage Pin voltage FE 0.5AVDD – 0.03 0.5AVDD + 0.03 V Input conversion VDF-FE DC offset temperature drift Offset voltage – 20 – TE Symbol 2.5V VOFFFE Pin voltage Frequency FFE1 characteristics 1 $3AA104 Frequency FFE2 characteristics 2 $3AA118 FE 30mVp-p 10/ 100kHz µV/ °C ±2.8 3V 20 log (V100k/V10k) –0.06 0 0.06 V –1 0 1 dB –1 0 1 dB 3 % FE 52mVp-p (V50k/V100k) × 100 FE VIR-TE VC reference about (B + D) and (A + C) TE 0.4AVDD 0.6AVDD V VOR-TE Pin voltage TE 0.5 AVDD – 0.5 V Input conversion VOF-TE DC offset voltage Pin voltage TE 0.5AVDD – 0.03 0.5AVDD + 0.03 V Distortion rate DFE Input voltage range Output voltage range 600mVp-p 50kHz Input conversion VDF-TE DC offset temperature drift Offset voltage 2.5V VOFFTE Frequency FTE2 characteristics 2 $3AA218 45mVp-p DTE $3AA200 480mVp-p TE 28mVp-p 10/ 100kHz 50kHz 20 log (V100k/V10k) (V50k/V100k) × 100 –0.075 0 0.075 V –1 0 1 dB –1 0 1 dB 3 % TE TE CXD3059AR $3AA204 µV/ °C ±2.5 Pin voltage Frequency FTE1 characteristics 1 Distortion rate 3V Bias conditions EQ Measurement item Symbol SW conditions Sending command AC input AC input DC input amplitude frequency voltage DC input current VDD AVDD Measurement conditions Measurement pins Min. Typ. Max. Unit 250 mVp-p Input voltage range VIR-EQ Distortion rate 3% or less, no DC bias RFACO Output voltage range VOR-EQ Pin voltage RFACO 0.5 AVDD – 0.5 V Input conversion VOF-EQ DC offset voltage Pin voltage RFACO –0.25 0.25 V Input conversion VDF-EQ DC offset temperature drift Offset voltage 2.5V VOFFEQ Ta = –20 to +75°C Pin voltage – 21 – Frequency FEQ1 characteristics 1 $3AA204 Frequency FEQ2 characteristics 2 $3AA218 45mVp-p DEQ $3AA200 1.2Vp-p Distortion rate 3V RFACO 28mVp-p 10/ 100kHz 360kHz 20 log (V100k/V10k) V ±0.1 –0.5 0 0.5 V –1 0 1 dB –1 0 1 dB 3 % RFACO (V720k/V360k) × 100 RFACO CXD3059AR CXD3059AR Notes on Operation for RFC Pin • Set each impedance of the heavy line shown bellow 0.1Ω or less. • Make each wiring length of L1 to L4, L1 ≤ 20mm, L2 ≤ 20mm and L3 + L4 ≤ 40mm. • Use the bypass condenser C with capacitance led by resistance (regulator output impedance and wiring resistance to C) or more seeing the figure bellow. 5 Regulator 4 OUT R [Ω] GND R AVS 3 2 0.1µF 1 C L3 L2 0 0 20 40 60 80 100 C [µF] L1 15kΩ 0.1µF Impedance R tolerance for bypass condenser C L4 AVSS4 RFC AVDD4 – 22 – CXD3059AR DC-DC Converter Characteristics (VDD = XVDD = 2.5 ± 0.2V, IOVDD0 to 2 = AVDD0 to 5 = 3.3 ± 0.3V, VSS = XVSS = IOVSS = AVSS = 0V, Topr = –20 to +75°C) Item Symbol Conditions Min. Typ. Max. Unit Output voltage VO — 2.3 2.5 2.7 V Output current Iope — — — 100 mA VOUT DDVROUT DDCR R1 C1 C2 DC-DC converter application circuit sample (1) C2 is the oscillation stopping capacitor. Since there is possibility of an oscillation when the capacity value changes by temperature change etc., the electrolytic capacitor with small internal series resistance (ESR) is recommended. Capacitance 100µF is recommended. (Should be 50µF or more) (2) Since protection circuit is built in the DC-DC converter output, it operates when an overcurrent flows. Cancelling after protection circuit operation needs to make power supply voltage 0.7V or less once. After that, when you switch ON power supply, set XRST pin in the condition of low. To cancel the reset, set high after holding XRST low 100ns or more after power ON. (3) The R1 and C1 of application circuit example have the constant assuming that power supply rise time is 400ms or less. When it is 400ms or more, it is necessary to enlarge the value of R1 × C1. – 23 – CXD3059AR CPU Interface Timing 750ns to 30µs CLOK D0 DATA D18 D1 D19 D20 D21 D22 D23 750ns or more XLAT Valid Registers Spindle Output n . 236 (ns) n = 0 to 31 Acceleration MDP Z 132kHz 7.6µs Deceleration Acceleration MDP Z 264kHz 3.8µs Deceleration Servo Output MCK (5.6448MHz) ↑ ↑ ↑ ↑ ↑ ↑ ↑ Output value + A Output value – A Output value 0 64tMCK 64tMCK 64tMCK SLD SFDR AtMCK SRDR AtMCK FCS/TRK 32tMCK FFDR/ TFDR FRDR/ TRDR A tMCK 2 32tMCK 32tMCK 32tMCK A tMCK 2 A tMCK 2 – 24 – A tMCK 2 32tMCK 32tMCK CXD3059AR DA Interface CDDSP output selected (1× × speed playback LRCK = 44.1kHz, BCK = 2.1168MHz) LRCK 2 1 3 4 5 6 7 8 9 10 11 12 24 BCK WDCK PCMD R0 L14 L13 L12 L11 L10 L9 Lch MSB (15) L8 L7 L6 L5 L4 L3 L2 L1 L0 Rch MSB DAC output selected (1× × speed playback LRCK = 44.1kHz, BCK = 2.8224MHz) $A5EA OBIT1 = 1, OBIT0 = 1 LRCK 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 32 BCK WDCK PCMD R0 L14 L13 L12 L11 L10 L9 L8 L7 L6 L5 L4 L3 L2 L1 L0 Rch MSB L16 L15 L14 L13 L12 L11 L10 L9 L8 L7 L6 L5 L4 L3 L2 L1 L0 Rch MSB L18 L17 L16 L15 L14 L13 L12 L11 L10 L9 L8 L7 L6 L5 L4 L3 L2 L1 L0 Rch MSB Lch MSB (15) $A5EA OBIT1 = 1, OBIT0 = 0 Lch MSB (17) PCMD R0 $A5EA OBIT1 = 0, OBIT0 = 0 PCMD R0 Lch MSB (19) DAC block input timing (LRCK = 44.1kHz, BCK = 2.1168MHz) LRCKI 1 2 3 4 5 6 7 8 9 10 11 24 12 BCKI PCMDI R0 Lch MSB (15) L14 L13 L12 L11 L10 L9 – 25 – L8 L7 L6 L5 L4 L3 L2 L1 L0 Rch MSB CXD3059AR EMPH DOUT RMUT Lch Rch Application Circuit BCK PCMD LRCK LRCKI PCMDI VSS LRCK BCK PCMD VDD EMPH EMPHI DOUT IOVDD2 TES1 TEST NC IOVSS2 XVSS XTAI XTAO XVDD AVDD1 AOUT1 AVSS1 VREFL AVSS2 AOUT2 NC VREFR 91 LMUT AVDD2 LMUT RMUT IOVDD0 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 BCKI 60 92 NC NC 59 93 XTSL SQSO SBSO DDCR 58 94 IOVSS0 AVSS5 57 95 XTACN DDVRSEN 56 96 SQSO DDVROUT 55 97 SQCK AVDD5 54 98 SBSO PCO 53 SQCK 99 EXCK FILI 52 XRST 100 XRST FILO 51 SYSM 101 SYSM CLTV 50 DATA 102 DATA AVSS3 49 XLAT 103 VSS VCTL 48 CLOK 104 XLAT VPCO 47 SENS 105 CLOK SCLK 106 VDD SCOR 107 SENS BIAS 44 FOK 108 SCLK AVDD3 43 ASYO 46 CXD3059AR ASYI 45 109 ATSK RFACI 42 WFCK 110 WFCK RFACO 41 XUGF 111 XUGF AVSS4 40 XPCK 112 XPCK RFC 39 GFS C2PO 113 GFS NC 38 114 C2PO PD 37 115 SCOR LD 36 116 VDD C4M Driver circuit EQ_IN 35 AC_SUM 34 118 WDCK PDSENS 33 COUT 119 COUT RFDCO 32 RFDCO PD NC D C B A AVDD4 31 VC FEO FEI TEO TEI F 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 E SFDR 8 NC IOVSS1 7 AVSS0 SSTP 6 AVDD0 MDP 5 FRDR LOCK 4 FFDR VSS 3 TRDR FOK 2 TFDR DFCT 1 SRDR MIRR IOVDD1 117 C4M WDCK 120 NC DDVROUT LD A.GND D B LOCK MIRR DFCT C A VC F E FD TD Driver circuit SLED SPDL Limit switch Application circuits shown are typical examples illustrating the operation of the devices. Sony cannot assume responsibility for any problems arising out of the use of these circuits or for any infringement of third party patent and other right due to same. – 26 – CXD3059AR Package Outline Unit: mm 120PIN LQFP (PLASTIC) 18.0 ± 0.2 1.7 MAX 1.4 ± 0.1 16.0 ± 0.1 90 S 61 0.1 91 S 60 B A 120 31 1 30 0.5 b 0.1 M S DETAIL A 0.125 ± 0.03 0˚ to 10˚ 0.6 ± 0.15 b = 0.20 ± 0.03 (0.5) 0.25 (17.0) 0.1 ± 0.05 DETAIL B PACKAGE STRUCTURE PACKAGE MATERIAL EPOXY RESIN SONY CODE LQFP-120P-L01 LEAD TREATMENT PALLADIUM PLATING EIAJ CODE LQFP120-P-1616 LEAD MATERIAL COPPER ALLOY PACKAGE MASS 0.8g JEDEC CODE – 27 – Sony Corporation