SLD432S Preliminary 40W Array Laser Diode Description The SLD432S is a high power laser diode with an array structure, which achieves 40W high power. M-S006 Features • High power Recommended optical power output: Po = 40W • Array structure • Open package Applications Solid state laser excitation Structure GaAlAs quantum well structure laser diode Absolute Maximum Ratings (Tc = 25°C) • Optical power output Pomax 44 • Reverse voltage VR LD 2 W V Operating Lifetime MTTF 10,000H (effective value) at Po = 20W, Tc = 25°C Warranty This warranty period shall be 90 days after receipt of the product or 1,000 hours operation time whichever is shoter. Sony Quality Assurance Department shall analyze any product that fails during said warranty period, and if the analysis results show that the product failed due to material or manufacturing defects on the part of Sony, the product shall be replaced free of charge. Laser diodes naturally have differing lifetimes which follow a Weibull distribution. Sony reserves the right to change products and specifications without prior notice. This information does not convey any license by any implication or otherwise under any patents or other right. Application circuits shown, if any, are typical examples illustrating the operation of the devices. Sony cannot assume responsibility for any problems arising out of the use of these circuits. –1– PE02441-PS SLD432S Electrical and Optical Characteristics Item Symbol (Tc = 25°C, Tc: case temperature) Conditions Min. Typ. Max. Unit — 14 18 A Threshold current Ith Operating current Iop Po = 40W — 50 55 A Operating voltage Vop Po = 40W — 1.9 2.8 V Wavelength λp Po = 40W 805 — 811 nm Wavelength spectrum width λw Po = 40W (FWHM) — — 2.5 nm — 24 30 degree — 8 15 degree — — ±300 µm — — ±5 degree — — ±4 degree — 1.1 — W/A Radiation angle Positional accuracy Perpendicular θ⊥ Parallel θ// Position ∆X, ∆Y Angle Differential efficiency ∆φ⊥ ∆φ// ηD Po = 40W Po = 40W Po = 40W –2– SLD432S Notes on Operation Care should be taken for the following points when using this product. (1) This product corresponds to a Class 4 product under IEC60825-1 and JIS standard C6802 "Laser Product Emission Safety Standards". LASER DIODE LASER DIODE This product complies with 21 CFR Part 1040.10 and 1040.11 LASER RADIATION AVOID EYE OR SKIN EXPOSURE TO DIRECT OR SCATTERED RADIATION MAXIMUM OUTPUT WAVELENGTH OVER 1 W 600 - 950 nm CLASS IV LASER PRODUCT Sony Corporation AVOID EXPOSURE Laser radiation is emitted from this aperture. 6-7-35 Kitashinagawa, Shinagawa-ku,Tokyo 141-0001 Japan (2) Eye protection against laser beams Take care not to allow laser beams to enter your eyes under any circumstances. For observing laser beams, ALWAYS use safety goggles that block laser beams. Usage of IR scopes, IR cameras and fluorescent plates is also recommended for monitoring laser beams safely. (3) Gallium Arsenide This product uses gallium arsenide (GaAs). This is not a problem for normal use, but GaAs vapors may be potentially hazardous to the human body. Therefore, never crush, heat to the maximum storage temperature or higher, or place the product in your mouth. In addition, the following disposal methods are recommended when disposing of this product. 1. Engaging the services of a contractor certified in the collection, transport and intermediate treatment of items containing arsenic. 2. Managing the product through to final disposal as specially managed industrial waste which is handled separately from general industrial waste and household waste. (4) Prevention of surge current and electrostatic discharge Laser diodes are most sensitive to electrostatic discharge among semiconductors. When a large current is passed through the laser diode for even an extremely short time, the strong light emitted from the laser diode promotes deterioration and then destruction of the laser diode. Therefore, note that surge current should not flow to the laser diode driving circuit from switches and others. Also, if the laser diode is handled carelessly, it may be destroyed instantly because electrostatic discharge is easily applied by a human body. Therefore, be extremely careful about overcurrent and electrostatic discharge. (5) Use for special applications This product is not designed or manufactured for use in equipment used under circumstances where failure may pose a risk to life and limb, or result in significant material damage, etc. Consult your Sony sales representative when investigating use for medical, vehicle, nuclear power control or other special applications. Also, use the power supply that was designed not to exceed the optical power output specified at the absolute maximum ratings. –3– SLD432S Package Outline Unit: mm M-S006 M3 17.8 3-Cross-Recessed Head Machine Screws(M2) 5.5 LD( – ) 2-φ3.2 20 ± 0.5 2 5 10 17 14 ± 0.2 LD( + ) 10 ± 0.2 4.7 ± 0.1 15 6 LD CHIP 24.9 ± 0.2 7 8 9 2 (10.3) φ2 DEPTH4 SONY CODE M-S006 EIAJ CODE JEDEC CODE PACKAGE MASS –4– 18.36g Sony Corporation