TI DAC3283IRGZR

DAC3283
www.ti.com
SLAS693A – MARCH 2010 – REVISED APRIL 2010
Dual-Channel, 16-Bit, 800 MSPS, Digital-to-Analog Converter (DAC)
Check for Samples: DAC3283
FEATURES
APPLICATIONS
•
•
•
•
•
•
1
•
•
•
•
•
•
•
•
•
•
•
Dual, 16-Bit, 800 MSPS DACs
8-Bit Input LVDS Data Bus
– Byte-Wide Interleaved Data Load
– 8 Sample Input FIFO
– Optional Data Pattern Checker
Multi-DAC Synchronization
Selectable 2x-4x Interpolation Filters
– Stop-Band Attenuation > 85 dB
Fs/2 and ± Fs/4 Coarse Mixer
Digital Quadrature Modulator Correction
– Gain, Phase and Offset Correction
Temperature Sensor
3- or 4-Wire Serial Control Interface
On-Chip 1.2-V Reference
Differential Scalable Output: 2 to 20 mA
Single-Carrier TM1 WCDMA ACLR: 82 dBc at
fOUT = 122.88 MHz
Low Power: 1.3 W at 800 MSPS
Space Saving Package: 48-pin 7×7mm QFN
Cellular Base Stations
Diversity Transmit
Wideband Communications
Digital Synthesis
DESCRIPTION
The DAC3283 is a dual-channel 16-bit 800 MSPS
digital-to-analog converter (DAC) with an 8-bit LVDS
input data bus with on-chip termination, optional
2x-4x interpolation filters, digital IQ compensation and
internal voltage reference. The DAC3283 offers
superior linearity, noise and crosstalk performance.
Input data can be interpolated by 2x or 4x through
on-chip interpolating FIR filters with over 85 dB of
stop-band attenuation. Multiple DAC3283 devices can
be fully synchronized.
The DAC3283 allows either a complex or real output.
An optional coarse mixer in complex mode provides
frequency upconversion and the dual DAC output
produces a complex Hilbert Transform pair. The
digital IQ compensation feature allows optimization of
phase, gain and offset to maximize sideband rejection
and minimize LO feed-through of an external
quadrature modulator performing the final single
sideband RF up-conversion.
The DAC3283 is characterized for operation over the
entire industrial temperature range of –40°C to 85°C
and is available in a 48-pin 7×7mm QFN package.
ORDERING INFORMATION
TA
–40°C to 85°C
(1)
(2)
(3)
ORDER CODE
DAC3283IRGZT
DAC3283IRGZR
PACKAGE DRAWING/TYPE (1)
(2) (3)
RGZ/64QFN Quad Flatpack No-Lead
TRANSPORT MEDIA
Tape and Reel
QUANTITY
250
2000
Thermal Pad Size: 5,6 mm × 5,6 mm
MSL Peak Temperature: Level-3-260C-168 HR
For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI
website at www.ti.com.
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2010, Texas Instruments Incorporated
DAC3283
SLAS693A – MARCH 2010 – REVISED APRIL 2010
www.ti.com
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
DACVDD18
VFUSE
DIGVDD18
CLKVDD18
FUNCTIONAL BLOCK DIAGRAM
DACCLKP
Clock Distribution
LVPECL
1.2 V
Reference
DACCLKN
QMC
A-offset
DATACLKN
FIR0
D0N
23 taps
x2
x2
QMC
Phase and Gain
59 taps
Coarse Mixer
Fs/4, -Fs/4, Fs/2
x2
LVDS
16-b
DAC
16-b
DAC
QMC
B-offset
Frame Strobe
100
FRAMEP
16
x2
Programmable Delay
(0-3T)
100
LVDS
16
8 Sample FIFO
Pattern
Test
De-interleave
D7N
D0P
A
gain
FIR1
LVDS
100
D7P
BIASJ
LVDS
100
DATACLKP
EXTIO
IOUTA1
IOUTA2
IOUTB1
IOUTB2
B
gain
FRAMEN
OSTRP
Temp
Sensor
Submit Documentation Feedback
TXENABLE
SCLK
SDENB
SDIO
ALARM_SDO
2
AVDD33
GND
Control Interface
LVPECL
OSTRN
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): DAC3283
DAC3283
www.ti.com
SLAS693A – MARCH 2010 – REVISED APRIL 2010
AVDD33
41
37
VFUSE
42
IOUTA1
AVDD33
43
38
BIASJ
44
AVDD33
EXTIO
45
IOUTA2
AVDD33
46
39
IOUTB2
47
40
AVDD33
IOUTB1
48
DAC3283
RGZ PACKAGE
(TOP VIEW)
CLKVDD18
1
36
DACVDD18
DACVDD18
2
35
CLKVDD18
DACCLKP
3
34
ALARM_SDO
DACCLKN
4
33
SDENB
GND
5
32
SCLK
31
SDIO
OSTRP
6
OSTRN
7
DIGVDD18
8
D7P
DAC3283
RGZ Package
48-QFN 7x7mm
(Top View )
19
20
21
22
23
24
FRAMEN
D3P
D3N
D2P
D2N
D1P
FRAMEP
25
18
12
DATACLKN
D1N
D6N
17
D0P
26
16
27
11
D4N
10
D6P
DATACLKP
D7N
15
D0N
D4P
28
14
9
13
DIGVDD18
D5P
TXENABLE
29
D5N
30
TERMINAL FUNCTIONS
TERMINAL
NAME
NO.
I/O
DESCRIPTION
37, 40, 42,
45, 48
I
ALARM_SDO
34
O
1.8V CMOS output for ALARM condition. The ALARM output functionality is defined through the
CONFIG6 register. Default polarity is active low, but can be changed to active high via CONFIG0
alarm_pol control bit. Optionally, it can be used as the uni-directional data output in 4-pin serial
interface mode (CONFIG 23 sif4_ena = '1').
BIASJ
43
O
Full-scale output current bias. For 20mA full-scale output current, connect a 960Ω resistor to GND.
1, 35
I
Internal clock buffer supply voltage. (1.8 V) It is recommended to isolate this supply from DACVDD18
and DIGVDD18.
AVDD33
CLKVDD18
D[7..0]P
9, 11, 13,
15, 21, 23,
25, 27
I
Analog supply voltage. (3.3 V)
LVDS positive input data bits 0 through 7. Each positive/negative LVDS pair has an internal 100 Ω
termination resistor. Data format relative to DATACLKP/N clock is Double Data Rate (DDR) with two
data transfers per DATACKP/N clock cycle. Dual channel 16-bit data is transferred byte-wide on this
single 8-bit data bus using FRAMEP/N as a frame strobe indicator.
D7P is most significant data bit (MSB) – pin 9
D0P is least significant data bit (LSB) – pin 27
The order of the bus can be reversed via CONFIG19 rev bit.
LVDS negative input data bits 0 through 15. (See D[7:0]P description above)
10, 12, 14,
16, 22, 24,
26, 28
I
DACCLKP
3
I
Positive external LVPECL clock input for DAC core with a self-bias of approximately CLKVDD18/2.
DACCLKN
4
I
Complementary external LVPECL clock input for DAC core. (see the DACCLKP description)
DACVDD18
2, 36
I
DAC core supply voltage. (1.8 V) It is recommended to isolate this supply from CLKVDD18 and
DIGVDD18.
D[7..0]N
D7N is most significant data bit (MSB) – pin 10
D0N is least significant data bit (LSB) – pin 28
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): DAC3283
3
DAC3283
SLAS693A – MARCH 2010 – REVISED APRIL 2010
www.ti.com
TERMINAL FUNCTIONS (continued)
TERMINAL
NAME
NO.
I/O
DESCRIPTION
DATACLKP
17
I
LVDS positive input data clock. This positive/negative pair has an internal 100 Ω termination resistor.
Input data D[7:0]P/N is latched on both edges of DATACLKP/N (Double Data Rate) with two data
transfers input per DATACLKP/N clock cycle.
DATACLKN
18
I
LVDS negative input data clock. (See DATACLKP description)
DIGVDD18
8, 29
I
Digital supply voltage. (1.8V) It is recommended to isolate this supply from CLKVDD18 and
DACVDD18.
EXTIO
44
I/O
Used as external reference input when internal reference is disabled through CONFIG25 extref_ena
= '1'. Used as internal reference output when CONFIG25 extref_ena = '0' (default). Requires a 0.1µF
decoupling capacitor to AGND when used as reference output.
FRAMEP
19
I
LVDS frame indicator positive input. This positive/negative pair has an internal 100Ω termination
resistor. This signal is captured with the rising edge of DATACLKP/N and used to indicate the
beginning of the frame. It is also used as a reset signal by the FIFO. The FRAMEP/N signal should be
edge-aligned with D[7:0]P/N.
FRAMEN
20
I
LVDS frame indicator negative input. (See the FRAMEN description)
5, Thermal
Pad
I
Pin 5 and the Thermal Pad located on the bottom of the QFN package is ground for all supplies.
IOUTA1
38
O
A-Channel DAC current output. An offset binary data pattern of 0x0000 at the DAC input results in a
full scale current sink and the least positive voltage on the IOUTA1 pin. Similarly, a 0xFFFF data input
results in a 0 mA current sink and the most positive voltage on the IOUTA1 pin.
IOUTA2
39
O
A-Channel DAC complementary current output. The IOUTA2 has the opposite behavior of the
IOUTA1 described above. An input data value of 0x0000 results in a 0 mA sink and the most positive
voltage on the IOUTA2 pin.
IOUTB1
47
O
B-Channel DAC current output. Refer to IOUTA1 description above.
IOUTB2
46
O
B-Channel DAC complementary current output. Refer to IOUTA2 description above.
OSTRP
6
I
LVPECL output strobe positive input. This positive/negative pair is captured with the rising edge of
DACCLKP/N. It is used to reset the clock dividers and for multiple DAC synchronization. If unused it
can be left floating.
OSTRN
7
I
LVPECL output strobe negative input. (See the OSTRP description)
SCLK
32
I
1.8V CMOS serial interface clock. Internal pull-down.
SDENB
33
I
1.8V CMOS active low serial data enable, always an input to the DAC3283. Internal pull-up.
SDIO
31
I/O
TXENABLE
30
I
1.8V CMOS active high input. TXENABLE must be high for the DATA to the DAC to be enabled.
When TXENABLE is low, the digital logic section is forced to all 0, and any input data is ignored.
Internal pull-down.
VFUSE
41
I
Digital supply voltage. (1.8V) This supply pin is also used for factory fuse programming. Connect to
DACVDD18 pins for normal operation.
GND
4
1.8V CMOS serial interface data. Bi-directional in 3-pin mode (default). In 4-pin interface mode, the
SDIO pin is an input only. Internal pull-down.
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): DAC3283
DAC3283
www.ti.com
SLAS693A – MARCH 2010 – REVISED APRIL 2010
ABSOLUTE MAXIMUM RATINGS
over operating free-air temperature range (unless otherwise noted)
Supply voltage range
(1)
VALUE
UNIT
DACDVDD18 (2)
–0.5 to 2.3
V
DIGVDD18 (2)
–0.5 to 2.3
V
CLKVDD18 (2)
–0.5 to 2.3
V
–0.5 to 2.3
V
–0.5 to 4
V
–0.5 to 0.5
V
VFUSE
(2)
AVDD33 (2)
CLKVDD18 to DIGDVDD18
DACVDD18 TO DIGVDD18
Terminal voltage
range
–0.5 to 0.5
V
D[7..0]P ,D[7..0]N, DATACLKP, DATACLKN, FRAMEP, FRAMEN (2)
–0.5 to DIGVDD18 + 0.5
V
DACCLKP, DACCLKN, OSTRP, OSTRN (2)
–0.5 to CLKVDD18 + 0.5
V
ALARM_SDO, SDIO, SCLK, SDENB, TXENABLE
(2)
–0.5 to DIGCLKVDD18 + 0.5
V
IOUTA1/B1, IOUTA2/B2 (2)
–1.0 to AVDD33 + 0.5
V
EXTIO, BIASJ (2)
–0.5 to AVDD33 + 0.5
V
20
mA
Peak input current (any input)
Peak total input current (all inputs)
–30
mA
Operating free-air temperature range, TA: DAC3283
–40 to 85
°C
Storage temperature range
–65 to 150
°C
(1)
(2)
Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of these or any other conditions beyond those indicated under recommended operating conditions is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
Measured with respect to GND.
THERMAL CHARACTERISTICS
over operating free-air temperature range (unless otherwise noted)
THERMAL CONDUCTIVITY
TJ
qJA
Maximum junction temperature
48ld QFN
UNIT
125
°C
Theta junction-to-ambient (still air)
30
Theta junction-to-ambient (150 lfm)
24
qJB
Theta junction-to-board
qJp
Theta junction-to-pad
(1)
(2)
(1) (2)
°C/W
8
°C/W
1.3
°C/W
Air flow or heat sinking reduces qJA and may be required for sustained operation at 85° under maximum operating conditions.
It is strongly recommended to solder the device thermal pad to the board ground plane.
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): DAC3283
5
DAC3283
SLAS693A – MARCH 2010 – REVISED APRIL 2010
www.ti.com
ELECTRICAL CHARACTERISTICS — DC SPECIFICATIONS (1)
over operating free-air temperature range, nominal supplies, IOUTFS = 20 mA (unless otherwise noted)
PARAMETER
TEST CONDITIONS
RESOLUTION
MIN
TYP
MAX
16
UNIT
Bits
DC ACCURACY
DNL
Differential nonlinearity
INL
Integral nonlinearity
±2
1 LSB = IOUTFS/216
LSB
±4
ANALOG OUTPUT
Coarse gain linearity
Offset error
Gain error
±0.04
LSB
±0.01
%FSR
With external reference
±2
%FSR
With internal reference
±2
Mid code offset
Gain mismatch
With internal reference
Minimum full scale output current
Maximum full scale output current
Nominal full-scale current, IOUTFS = 16 x IBIAS
current.
Output compliance range (2)
IOUTFS = 20 mA
–2
%FSR
2
2
mA
20
AVDD –0.5V
Output resistance
Output capacitance
%FSR
mA
AVDD +0.5V
V
300
kΩ
5
pF
REFERENCE OUTPUT
Vref
Reference output voltage
1.14
Reference output current (3)
1.2
1.26
100
V
nA
REFERENCE INPUT
VEXTIO
Input voltage range
Input resistance
External reference mode
0.1
1.2
1.25
V
1
MΩ
Small signal bandwidth
472
kHz
Input capacitance
100
pF
±1
ppm of
FSR/°C
TEMPERATURE COEFFICIENTS
Offset drift
With external reference
Gain drift
With internal reference
±15
Reference voltage drift
±30
ppm of
FSR/°C
±8
ppm/°C
POWER SUPPLY
AVDD33
3.0
3.3
3.6
DACVDD18, DIGVDD18, CLKVDD18
1.7
1.8
1.9
I(AVDD33)
Analog supply current
I(DIGDVDD)
Digital supply current
I(DACVDD18)
DAC supply current
I(CLKVDD18)
Clock supply current
P
Power dissipation
Mode 1 (below)
Power supply rejection ratio
T
Operating range
(1)
(2)
(3)
6
V
149
mA
340
mA
55
mA
37
mA
Mode 1: fDAC = 800MSPS,
4x interpolation, Fs/4 mixer on, QMC on
1300
Mode 2: fDAC = 491.52MSPS,
2x interpolation, Mixer off, QMC on
1000
mW
750
mW
Mode 3: Sleep mode
fDAC = 800MSPS, 4x interpolation, Fs/4 mixer on,
CONFIG24 sleepa, sleepb set = 1
Mode 4: Power-Down mode
No clock, static data pattern,
CONFIG23 clkpath_sleep_a, clkpath_sleepb set = 1
CONFIG24 clkrecv_sleep, sleepa, sleepb set = 1
PSRR
V
7
DC tested
1450
18
±0.2
–40
25
mW
mW
%FSR/V
85
°C
Measured differential across IOUTA1 and IOUTA2 with 25 Ω each to AVDD.
The lower limit of the output compliance is determined by the CMOS process. Exceeding this limit may result in transistor breakdown,
resulting in reduced reliability of the DAC3283 device. The upper limit of the output compliance is determined by the load resistors and
full-scale output current. Exceeding the upper limit adversely affects distortion performance and integral nonlinearity.
Use an external buffer amplifier with high impedance input to drive any external load.
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): DAC3283
DAC3283
www.ti.com
SLAS693A – MARCH 2010 – REVISED APRIL 2010
ELECTRICAL CHARACTERISTICS — AC SPECIFICATIONS
Over recommended operating free-air temperature range, nominal supplies, IOUTFS = 20 mA (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP MAX
UNIT
ANALOG OUTPUT (1)
1x Interpolation
312.5
2x Interpolation
625
4x Interpolation
800
fDAC
Maximum DAC output update rate
MSPS
ts(DAC)
Output settling time to 0.1%
Transition: Code 0x0000 to 0xFFFF
tpd
Output propagation delay
DAC outputs are updated on the falling edge of DAC
clock. Does not include digital latency (see below).
tr(IOUT)
Output rise time 10% to 90%
220
ps
tf(IOUT)
Output fall time 90% to 10%
220
ps
10.4
DAC wake-up time
IOUT current settling to 1% of IOUTFS. Measured
from SDENB rising edge; Register CONFIG24,
toggle sleepa from 1 to 0.
90
DAC sleep time
IOUT current settling to less than 1% of IOUTFS.
Measured from SDENB rising edge; Register
CONFIG24, toggle sleepa from 0 to 1.
90
Power-up
time
Digital latency
ns
2
ns
µs
1x Interpolation
59
2x Interpolation
139
4x Interpolation
290
QMC
24
fDAC = 800 MSPS, fOUT = 20.1 MHz
85
fDAC = 800 MSPS, fOUT = 50.1 MHz
76
fDAC = 800 MSPS, fOUT = 70.1 MHz
72
Third-order two-tone
intermodulation distortion
Each tone at –12 dBFS
fDAC = 800 MSPS, fOUT = 30 ± 0.5 MHz
93
fDAC = 800 MSPS, fOUT = 50 ± 0.5 MHz
90
fDAC = 800 MSPS, fOUT = 100 ± 0.5 MHz
86
Noise spectral density tone at
0dBFS
fDAC = 800 MSPS, fOUT = 10.1 MHz
162
fDAC = 800 MSPS, fOUT = 80.1 MHz
160
Adjacent channel leakage ratio,
single carrier
fDAC = 737.28 MSPS, fOUT = 30.72MHz
85
fDAC = 737.28 MSPS, fOUT = 153.6MHz
81
Alternate channel leakage ratio,
single carrier
fDAC = 737.28 MSPS, fOUT = 30.72MHz
91
fDAC = 737.28 MSPS, fOUT = 153.6MHz
85
Channel isolation
fDAC = 800 MSPS, fOUT = 10MHz
84
DAC
clock
cycles
AC PERFORMANCE (2)
SFDR
IMD3
NSD
WCDMA (3)
(1)
(2)
(3)
Spurious free dynamic range (0 to
fDAC/2)Tone at 0 dBFS
dBc
dBc
dBc/Hz
dBc
dBc
dBc
Measured single-ended into 50Ω load.
4:1 transformer output termination, 50Ω doubly terminated load
Single carrier, W-CDMA with 3.84 MHz BW, 5-MHz spacing, centered at fOUT, PAR = 12dB. TESTMODEL 1, 10 ms
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): DAC3283
7
DAC3283
SLAS693A – MARCH 2010 – REVISED APRIL 2010
www.ti.com
ELECTRICAL CHARACTERISTICS – DIGITAL SPECIFICATIONS
over recommended operating free-air temperature range, nominal supplies, IOUTFS = 20 mA (unless otherwise noted)
PARAMETER
LVDS INTERFACE:D[7:0]P/N, DATACLKP/N, FRAMEP/N
TEST CONDITIONS
MIN
TYP
MAX
UNIT
312.5
MSPS
1250
MSPS
(1)
Byte-wide DDR format
DATACLK frequency = 625 MHz
fDATA
Input data rate
fBUS
Byte-wide LVDS data transfer rate
VA,B+
Logic high differential input voltage threshold
150
400
VA,B–
Logic low differential input voltage threshold
–150
–400
VCOM
Input common mode
0.9
1.2
1.5
V
ZT
Internal termination
85
110
135
Ω
CL
LVDS Input capacitance
mV
mV
2
pF
TIMING LVDS INPUTS: DATACLKP/N DOUBLE EDGE LATCHING – See Figure 40
ts(DATA)
Setup time, D[7:0]P/N and FRAMEP/N, valid
to either edge of DATACLKP/N
FRAMEP/N latched on rising edge of
DATACLKP/N only
–25
ps
th(DATA)
Hold time, D[7:0]P/N and FRAMEP/N, valid
after either edge of DATACLKP/N
FRAMEP/N latched on rising edge of
DATACLKP/N only
375
ps
t(FRAME)
FRAMEP/N pulse width
fDATACLK is DATACLK frequency in MHz
t_align
Maximum offset between DATACLKP/N and
DACCLKP/N rising edges
FIFO bypass mode only fDACCLK is
DACCLK frequency in MHz
1/2fDATACLK
ns
1/2fDACCLK
–0.55
ns
CLOCK INPUT (DACCLKP/N)
Duty cycle
40%
Differential voltage (2)
0.4
60%
1.0
DACCLKP/N Input Frequency
V
800
MHz
OUTPUT STROBE (OSTRP/N)
fOSTR
fOSTR = fDACCLK / (n × 8 × Interp) where n is
any positive integer fDACCLK is DACCLK
frequency in MHz
Frequency
fDACCLK / (8
x interp)
Duty cycle
40%
Differential voltage
0.4
60%
1.0
V
TIMING OSTRP/N INPUT: DACCLKP/N RISING EDGE LATCHING
ts(OSTR)
Setup time, OSTRP/N valid to rising edge of
DACCLKP/N
200
ps
th(OSTR)
Hold time, OSTRP/N valid after rising edge
of DACCLKP/N
200
ps
CMOS INTERFACE: ALARM_SDO, SDIO, SCLK, SDENB, TXENABLE
VIH
High-level input voltage
VIL
Low-level input voltage
IIH
High-level input current
–40
IIL
Low-level input current
–40
CI
CMOS input capacitance
VOH
1.25
V
40
mA
40
mA
2
ALARM_SDO, SDIO
pF
Iload = –100 mA
DIGVDD18
–0.2
V
Iload = –2mA
0.8 x
DIGVDD18
V
ALARM_SDO, SDIO
VOL
V
0.54
Iload = 100 mA
0.2
V
Iload = 2 mA
0.5
V
SERIAL PORT TIMING – See Figure 32 and Figure 33
ts(SDENB)
Setup time, SDENB to rising edge of SCLK
20
ns
ts(SDIO)
Setup time, SDIO valid to rising edge of
SCLK
10
ns
th(SDIO)
Hold time, SDIO valid to rising edge of SCLK
5
ns
1
ms
100
ns
t(SCLK)
Period of SCLK
Register CONFIG5 read (temperature
sensor read)
All other registers
(1)
(2)
8
See LVDS INPUTS section for terminology.
Driving the clock input with a differential voltage lower than 1V will result in degraded performance.
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): DAC3283
DAC3283
www.ti.com
SLAS693A – MARCH 2010 – REVISED APRIL 2010
ELECTRICAL CHARACTERISTICS – DIGITAL SPECIFICATIONS (continued)
over recommended operating free-air temperature range, nominal supplies, IOUTFS = 20 mA (unless otherwise noted)
PARAMETER
t(SCLKH)
High time of SCLK
t(SCLKL)
Low time of SCLK
td(Data)
Data output delay after falling edge of SCLK
TEST CONDITIONS
MIN
TYP
MAX
UNIT
Register CONFIG5 read (temperature
sensor read)
0.4
ms
All other registers
40
ns
Register CONFIG5 read (temperature
sensor read)
0.4
ms
All other registers
40
ns
10
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): DAC3283
ns
9
DAC3283
SLAS693A – MARCH 2010 – REVISED APRIL 2010
www.ti.com
5
5
4
4
3
3
2
2
Error - LSB
Error - LSB
TYPICAL CHARACTERISTICS
1
0
-1
1
0
-1
-2
-2
-3
-3
-4
-4
-5
0
-5
0
10000 20000 30000 40000 50000 60000 70000
Code
Figure 1. INTEGRAL NON-LINEARITY
Figure 2. DIFFERENTIAL NON-LINEARITY
100
fDAC = 800 MSPS, 4x Interpolation,
IOUTFS = 20 mA
95
fDAC = 800 MSPS, 4x Interpolation,
IOUTFS = 20 mA
95
90
90
Second Harmonic - dBc
SFDR - Spurious Free Dynamic Range - dBc
100
85
80
75
70
-6 dBFS
-12 dBFS
65
85
80
75
-6 dBFS
-12 dBFS
70
65
60
60
0 dBFS
55
55
50
0
50
100
150
200
fOUT - MHz
250
300
350
Figure 3. SPURIOUS FREE DYNAMIC RANGE vs INPUT SCALE
10
10000 20000 30000 40000 50000 60000 70000
Code
50
0
0 dBFS
50
100
150
200
fOUT - MHz
250
300
350
Figure 4. SECOND HARMONIC vs INPUT SCALE
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): DAC3283
DAC3283
www.ti.com
SLAS693A – MARCH 2010 – REVISED APRIL 2010
TYPICAL CHARACTERISTICS (continued)
105
100
100
SFDR - Spurious Free Dynamic Range - dBc
fDAC = 800 MSPS, 4x Interpolation,
IOUTFS = 20 mA
Third Harmonic - dBc
95
-6 dBFS
90
-12 dBFS
85
80
75
70
65
60
0 dBFS
55
50
0
100
150
200
fOUT - MHz
250
300
85
80
75
65
60
55
0
20
40
60
80
fOUT - MHz
100
120
100
SFDR - Spurious Free Dynamic Range - dBc
4x Interpolation, 0 dBFS
IOUTFS = 20 mA
90
fDAC = 200 MSPS
85
80
fDAC = 400 MSPS
75
70
fDAC = 800 MSPS
65
60
55
50
0
4x interpolation
70
Figure 6. SPURIOUS FREE DYNAMIC RANGE vs
INTERPOLATION
100
95
1x interpolation
2x interpolation
350
Figure 5. THIRD HARMONIC vs INPUT SCALE
SFDR - Spurious Free Dynamic Range - dBc
90
50
50
fDAC = 312.5 MSPS, 0 dBFS,
IOUTFS = 20 mA
95
90
85
80
100
150
200
fOUT - MHz
250
300
350
Figure 7. SPURIOUS FREE DYNAMIC RANGE vs fDAC
10 mA
75
70
20 mA
65
60
55
2 mA
50
50
fDAC = 800 MSPS, 4x Interpolation,
0 dBFS
95
0
50
100
150
200
fOUT - MHz
250
300
350
Figure 8. SPURIOUS FREE DYNAMIC RANGE vs IOUTFS
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): DAC3283
11
DAC3283
SLAS693A – MARCH 2010 – REVISED APRIL 2010
www.ti.com
TYPICAL CHARACTERISTICS (continued)
10
10
2x Interpolation,
fDAC = 500 MSPS,
fOUT = 50 MHz
0
-10
-10
-20
Power - dBm
Power - dBm
-20
-30
-40
-50
-30
-40
-50
-60
-60
-70
-70
-80
-80
-90
10
60
110
160
f - Frequency - MHz
-90
10
210
Figure 9. SINGLE TONE SPECTRAL PLOT
60
110
160
f - Frequency - MHz
210
Figure 10. SINGLE TONE SPECTRAL PLOT
10
100
4x Interpolation, 0 dBFS
fDAC = 800 MSPS,
fOUT = 150 MHz
0
-10
90
-20
85
-30
80
-40
-50
fDAC = 800 MSPS, 4x Interpolation,
Tones at fOUT ±0.5 MHz,
IOUTFS = 20 mA
95
IMD3 - dBc
Power - dBm
2x Interpolation,
fDAC = 500 MSPS,
fOUT = 100 MHz
0
-6 dBFS
0 dBFS
75
70
-12 dBFS
-60
65
-70
60
-80
55
-90
10
50
60
110
160 210 260
f - Frequency - MHz
310
360
0
Figure 11. SINGLE TONE SPECTRAL PLOT
12
Submit Documentation Feedback
50
100
150
200
fOUT - MHz
250
300
350
Figure 12. IMD3 vs INPUT SCALE
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): DAC3283
DAC3283
www.ti.com
SLAS693A – MARCH 2010 – REVISED APRIL 2010
TYPICAL CHARACTERISTICS (continued)
100
100
fDAC = 312.5 MSPS,
Tones at fOUT ±0.5 MHz,
0 dBFS, IOUTFS = 20 mA
95
95
fDAC = 200 MSPS
90
90
85
85
IMD3 - dBc
IMD3 - dBc
fDAC = 800 MSPS
1x interpolation
80
4x interpolation
80
75
fDAC = 400 MSPS
70
65
75
4x Interpolation,
Tones at fOUT ±0.5 MHz,
0 dBFS, IOUTFS = 20 mA
60
2x interpolation
70
55
65
0
20
40
60
80
100
fOUT - MHz
120
140
50
0
160
50
Figure 13. IMD3 vs INTERPOLATION
100
150
200
fOUT - MHz
300
350
Figure 14. IMD3 vs fDAC
105
170
fDAC = 800 MSPS, 4x Interpolation,
Tones at fOUT ±0.5 Mhz, 0 dBFS
100
165
95
-6 dBFS
0 dBFS
160
90
10 mA
20 mA
NSD - dBc/Hz
85
IMD3 - dBc
250
80
75
70
65
2 mA
155
150
-12 dBFS
145
140
60
fDAC = 800 MSPS, 4x Interpolation,
IOUTFS = 20 mA
135
55
130
50
0
50
100
150
200
fOUT - MHz
250
300
350
0
Figure 15. IMD3 vs IOUTFS
50
100
150
200
fOUT - MHz
250
300
350
Figure 16. NSD vs INPUT SCALE
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): DAC3283
13
DAC3283
SLAS693A – MARCH 2010 – REVISED APRIL 2010
www.ti.com
TYPICAL CHARACTERISTICS (continued)
170
170
fDAC = 312.5 MSPS, 0 dBFS,
IOUTFS = 20 mA
165
fDAC = 400 MSPS
165
2x interpolation
1x interpolation
NSD - dBc/Hz
160
NSD - dBc/Hz
fDAC = 800 MSPS
160
4x interpolation
155
150
155
150 fDAC = 200 MSPS
145
140
145
135
140
0
20
40
60
80
100
fOUT - MHz
120
140
130
160
4x interpolation, 0 dBFS,
IOUTFS = 20 mA
0
50
Figure 17. NSD vs INTERPOLATION
150
200
fOUT - MHz
250
300
350
Figure 18. NSD vs fDAC
100
85
fDAC = 737.28 MSPS, 4x Interpolation,
IOUTFS = 20 mA
fDAC = 737.28 MSPS, 4x Interpolation,
IOUTFS = 20 mA
95
80
90
Aternate, 0 dBFS
Alternate -6 dBFS
ACLR, 0 dBFS
ACLR - dBc
Alternate 0 dBFS
ACLR - dBc
100
85
80
75
70
Alternate, -6 dBFS
Adjacent 0 dBFS
75
ACLR -6 dBFS
Adjacent -6 dBFS
65
70
65
0
50
100
150
200
fOUT - MHz
250
300
Figure 19. SINGLE CARRIER WCDMA ACLR vs INPUT SCALE
14
60
0
50
100
150
200
fOUT - MHz
250
300
Figure 20. FOUR CARRIER WCDMA ACLR vs INPUT SCALE
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): DAC3283
DAC3283
www.ti.com
SLAS693A – MARCH 2010 – REVISED APRIL 2010
TYPICAL CHARACTERISTICS (continued)
* RBW 30 kHz
* RBW 30 kHz
* VBW 300 kHz
* VBW 300 kHz
Ref
-12.3 dBm
-20
* Att
10 dB
Ref
* SWT 10 s
-20
4x Interpolation, 0 dBFS
fDAC = 737.28 MSPS,
fOUT = 70 MHz
-30
-40
-12.8 dBm
-40
-50
1 RM *
-50
CLRWR
-60
CLRWR
-60
10 dB
A
-70
-70
-80
-80
-90
-90
NOR
NOR
-100
-100
-110
-120
-110
-120
Center
70 MHz
2.55 MHz/
Span
25.5 MHz
Tx Channel
Bandwidth
3.84 MHz
Adjacent Channel
Bandwidth
Spacing
3.84 MHz
5 MHz
Lower
Upper
-82.20 dB
-82.07 dB
Alternate Channel
Bandwidth
Spacing
3.84 MHz
10 MHz
Lower
Upper
-86.11 dB
-85.86 dB
Center
W-CDMA 3GPP FWD
Power
-7.71 dBm
Figure 21. SINGLE CARRIER W-CDMA TEST MODEL 1
153.6 MHz
2.55 MHz/
-20
-30
* Att
10 dB
W-CDMA 3GPP FWD
Adjacent Channel
Bandwidth
Spacing
3.84 MHz
5 MHz
Lower
Upper
-80.69 dB
-81.00 dB
Alternate Channel
Bandwidth
Spacing
3.84 MHz
10 MHz
Lower
Upper
-84.07 dB
-84.16 dB
-50
Ref
-17.9 dBm
-20
-30
A
1 RM *
CLRWR
-60
* Att
10 dB
A
-60
-80
-80
-90
-90
NOR
-100
-100
-110
-110
NOR
-120
-120
Center
70 MHz
3.5 MHz/
Tx Channel
Bandwidth
Adjacent Channel
Bandwidth
Spacing
Span
Center
35 MHz
10 MHz
10.5 MHz
Power
Lower
Upper
153.6 MHz
Tx Channel
Bandwidth
W-CDMA 3GPP FWD
10 MHz
-8.50 dBm
Adjacent Channel
Bandwidth
Spacing
-79.64 dB
-80.05 dB
Figure 23. 10MHZ SINGLE CARRIER LTE
3.5 MHz/
10 MHz
10.5 MHz
-30
-40
-50
* Att
10 dB
* SWT 10 s
Ref
4x Interpolation, 0 dBFS
fDAC = 737.28 MSPS,
fOUT = 70 MHz
-19.6 dBm
-30
A
-40
-50
1 RM *
CLRWR
-60
CLRWR
-70
Power
Lower
Upper
-8.89 dBm
-78.21 dB
-78.12 dB
* Att
10 dB
* RBW 30 kHz
* VBW 300 kHz
* SWT 10 s
2x Interpolation, 0 dBFS
fDAC = 492.52 MSPS,
fOUT = 153.6 MHz
A
-60
-70
-80
-80
-90
-90
NOR
-100
-110
NOR
-100
-110
-120
Center
35 MHz
Figure 24. 10MHZ SINGLE CARRIER LTE
* VBW 300 kHz
-19 dBm
Span
W-CDMA 3GPP FWD
10 MHz
* RBW 30 kHz
1 RM *
* RBW 30 kHz
* VBW 300 kHz
* SWT 10 s
-70
-70
Ref
-8.07 dBm
4x Interpolation, 0 dBFS
fDAC = 737.28 MSPS,
fOUT = 153.6 MHz
-40
-50
1 RM *
CLRWR
Power
Figure 22. SINGLE CARRIER W-CDMA TEST MODEL 1
* SWT 10 s
4x Interpolation, 0 dBFS
fDAC = 737.28 MSPS,
fOUT = 70 MHz
-40
25.5 MHz
3.84 MHz
* VBW 300 kHz
-17.4 dBm
Span
Tx Channel
Bandwidth
* RBW 30 kHz
Ref
* SWT 10 s
4x Interpolation, 0 dBFS
fDAC = 737.28 MSPS,
fOUT = 153.6 MHz
-30
A
1 RM *
* Att
-120
70 MHz
Tx Channel
Bandwidth
Adjacent Channel
Bandwidth
Spacing
6.5 MHz/
Span
65 MHz
W-CDMA 3GPP FWD
20 MHz
20 MHz
20.5 MHz
Power
Lower
Upper
-7.38 dBm
-77.28 dB
-77.07 dB
Figure 25. 20MHZ SINGLE CARRIER LTE
Center
153.6 MHz
Tx Channel
Bandwidth
Adjacent Channel
Bandwidth
Spacing
6.5 MHz/
Span
65 MHz
W-CDMA 3GPP FWD
20 MHz
20 MHz
20.5 MHz
Power
Lower
Upper
-8.02 dBm
-73.41 dB
-73.54 dB
Figure 26. 20MHZ SINGLE CARRIER LTE
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): DAC3283
15
DAC3283
SLAS693A – MARCH 2010 – REVISED APRIL 2010
www.ti.com
TYPICAL CHARACTERISTICS (continued)
350
1200
300
1000
2x
250
4x
600
DVDD18 - mA
Power - mW
800
1x
2x
200
150
4x
400
100
200
QMC
Mixer
50
QMC
0
0
0
100 200 300 400 500 600 700 800 900
fDAC - MSPS
0
100 200 300 400 500 600 700 800 900
fDAC - MSPS
Figure 28. DVDD18 vs fDAC
80
40
70
35
60
30
50
Mixer On
40
30
Mixer Off
CLKVDD18 - mA
DACVDD18 - mA
Figure 27. POWER vs fDAC
25
20
15
20
10
10
5
0
0
100 200 300 400 500 600 700 800 900
fDAC - MSPS
0
0
100 200 300 400 500 600 700 800 900
fDAC - MSPS
Figure 29. DACVDD18 vs fDAC
16
Mixer
1x
Figure 30. CLKVDD18 vs fDAC
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): DAC3283
DAC3283
www.ti.com
SLAS693A – MARCH 2010 – REVISED APRIL 2010
TYPICAL CHARACTERISTICS (continued)
200
180
160
AVDD33 - mA
140
120
100
80
60
40
20
0
0
100 200 300 400 500 600 700 800 900
fDAC - MSPS
Figure 31. AVDD33 vs fDAC
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): DAC3283
17
DAC3283
SLAS693A – MARCH 2010 – REVISED APRIL 2010
www.ti.com
FUNCTIONAL DESCRIPTION
DEFINITION OF SPECIFICATIONS
Adjacent Carrier Leakage Ratio (ACLR): Defined for a 3.84Mcps 3GPP W-CDMA input signal measured in a
3.84MHz bandwidth at a 5MHz offset from the carrier with a 12dB peak-to-average ratio.
Analog and Digital Power Supply Rejection Ratio (APSSR, DPSSR): Defined as the percentage error in the
ratio of the delta IOUT and delta supply voltage normalized with respect to the ideal IOUT current.
Differential Nonlinearity (DNL): Defined as the variation in analog output associated with an ideal 1 LSB
change in the digital input code.
Gain Drift: Defined as the maximum change in gain, in terms of ppm of full-scale range (FSR) per °C, from the
value at ambient (25°C) to values over the full operating temperature range.
Gain Error: Defined as the percentage error (in FSR%) for the ratio between the measured full-scale output
current and the ideal full-scale output current.
Integral Nonlinearity (INL): Defined as the maximum deviation of the actual analog output from the ideal output,
determined by a straight line drawn from zero scale to full scale.
Intermodulation Distortion (IMD3, IMD): The two-tone IMD3 or four-tone IMD is defined as the ratio (in dBc) of
the worst 3rd-order (or higher) intermodulation distortion product to either fundamental output tone.
Offset Drift: Defined as the maximum change in DC offset, in terms of ppm of full-scale range (FSR) per °C,
from the value at ambient (25°C) to values over the full operating temperature range.
Offset Error: Defined as the percentage error (in FSR%) for the ratio between the measured mid-scale output
current and the ideal mid-scale output current.
Output Compliance Range: Defined as the minimum and maximum allowable voltage at the output of the
current-output DAC. Exceeding this limit may result reduced reliability of the device or adversely affecting
distortion performance.
Reference Voltage Drift: Defined as the maximum change of the reference voltage in ppm per degree Celsius
from value at ambient (25°C) to values over the full operating temperature range.
Spurious Free Dynamic Range (SFDR): Defined as the difference (in dBc) between the peak amplitude of the
output signal and the peak spurious signal.
Signal to Noise Ratio (SNR): Defined as the ratio of the RMS value of the fundamental output signal to the
RMS sum of all other spectral components below the Nyquist frequency, including noise, but excluding the first
six harmonics and dc.
18
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): DAC3283
DAC3283
www.ti.com
SLAS693A – MARCH 2010 – REVISED APRIL 2010
REGISTER DESCRIPTIONS
Table 1. Register Map
Name
Address
Default
CONFIG0
0x00
0x70
CONFIG1
0x01
0x11
CONFIG2
0x02
0x00
CONFIG3
0x03
0x10
CONFIG4
0x04
0xFF
CONFIG5
0x05
N/A
CONFIG6
0x06
0x00
(MSB)
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
reserved
fifo_ena
fifo_reset_ena
multi_sync_ena
alarm_out_ena
alarm_pol
qmc_offset_ena
qmc_correct_ena
fir0_ena
fir1_ena
unused
iotest_ena
unused
unused
sif_sync
sif_sync_ena
unused
unused
64cnt_ena
unused
unused
(LSB)
Bit 0
Bit 1
mixer_func(1:0)
unused
alarm_
2away_ena
fifo_offset(2:0)
coarse_daca(3:0)
twos
output_delay(1:0)
alarm_ 1away_ena
coarse_dacb(3:0)
tempdata(7:0)
unused
alarm_mask(6:0)
alarm_from_
zerochk
unused
alarm_fifo_
collision
reserved
alarm_from_
iotest
CONFIG7
0x07
0x00
CONFIG8
0x08
0x00
iotest_results(7:0)
CONFIG9
0x09
0x7A
iotest_pattern0(7:0)
CONFIG10
0x0A
0xB6
iotest_pattern1(7:0)
CONFIG11
0x0B
0xEA
iotest_pattern2(7:0)
CONFIG12
0x0C
0x45
iotest_pattern3(7:0)
CONFIG13
0x0D
0x1A
iotest_pattern4(7:0)
CONFIG14
0x0E
0x16
iotest_pattern5(7:0)
CONFIG15
0x0F
0xAA
iotest_pattern6(7:0)
CONFIG16
0x10
0xC6
CONFIG17
0x11
0x24
unused
alarm_fifo_
2away
alarm_fifo_ 1away
iotest_pattern7(7:0)
reserved
reserved
reserved
reserved
clk_alarm_mask
tx_off_mask
reserved
clk_alarm_ena
tx_off_ena
reserved
daca_
complement
dacb_
complement
clkdiv_sync_ena
unused
unused
unused
unused
multi_sync_sel
rev
CONFIG18
0x12
0x02
CONFIG19
0x13
0x00
CONFIG20
0x14
0x00
CONFIG21
0x15
0x00
CONFIG22
0x16
0x00
qmc_offseta(12:8)
unused
unused
unused
CONFIG23
0x17
0x00
qmc_offsetb(12:8)
sif4_ena
clkpath_sleep_a
clkpath_sleep_b
CONFIG24
0x18
0x83
sleepa
reserved
reserved
CONFIG25
0x19
0x00
extref_ena
reserved
reserved
CONFIG26
0x1A
0x00
CONFIG27
0x1B
0x00
CONFIG28
0x1C
0x00
qmc_gainb(7:0)
CONFIG29
0x1D
0x00
qmc_phase(7:0)
CONFIG30
0x1E
0x24
CONFIG31
0x1F
0x52
bequalsa
aequalsb
reserved
qmc_offseta(7:0)
qmc_offsetb(7:0)
tsense_ena
clkrecv_sleep
unused
reserved
sleepb
reserved
reserved
reserved
unused
reserved
qmc_gaina(7:0)
qmc_phase(9:8)
clk_alarm
qmc_gaina(10:8)
tx_off
qmc_gainb(10:8)
version(5:0)
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): DAC3283
19
DAC3283
SLAS693A – MARCH 2010 – REVISED APRIL 2010
www.ti.com
Register name: CONFIG0 – Address: 0x00, Default = 0x70
Register
Name
Address
Bit
Name
Default
Value
CONFIG0
0x00
7
qmc_offset_ena
When asserted the DAC offset correction is enabled.
0
6
fifo_ena
When asserted the FIFO is enabled. When the FIFO is bypassed
DACCCLKP/N and DATACLKP/N must be aligned to within t_align.
1
5
fifo_reset_ena
Allows the FRAME input to act as a FIFO write reset when asserted.
1
4
multi_sync_ena
Allows the FRAME or OSTR signals to be used as a sync signal when
asserted. This selection is determined by multi_sync_sel in register
CONFIG19.
1
Function
3
alarm_out_ena
When asserted the ALARM_SDO pin becomes an output. The functionality
of this pin is controlled by the CONFIG6 alarm_mask setting.
0
2
alarm_pol
This bit changes the polarity of the ALARM signal. (0=negative logic,
1=positive logic)
0
mixer_func(1:0)
Controls the function of the mixer block.
00
1:0
Mode
mixer_func(1:0)
Normal
00
High Pass (Fs/2)
01
Fs/4
10
–Fs/4
11
Register name: CONFIG1 – Address: 0x01, Default = 0x11
Register
Name
Address
Bit
CONFIG1
0x01
7
qmc_offset_ena
When asserted the QMC offset correction circuitry is enabled.
0
6
qmc_correct_ena
When asserted the QMC phase and gain correction circuitry is enabled.
0
5
fir0_ena
When asserted FIR0 is activated enabling 2x interpolation.
0
4
fir1_ena
When asserted FIR1 is activated enabling 4x interpolation. fir0_ena must
be set to '1' for 4x interpolation.
1
3
Unused
Reserved for factory use.
0
2
iotest_ena
When asserted enables the data pattern checker operation.
0
1
Unused
Reserved for factory use.
0
0
twos
When asserted the inputs are expected to be in 2's complement format.
When de-asserted the input format is expected to be offset-binary.
1
Name
Default
Value
Function
Register name: CONFIG2 – Address: 0x02, Default = 0x00
Register
Name
Address
Bit
CONFIG2
0x02
7
Unused
Reserved for factory use.
0
6
Unused
Reserved for factory use.
0
sif_sync
Serial interface created sync signal. Set to '1' to cause a sync and then
clear to '0' to remove it.
0
sif_sync_ena
When asserted this bit allows the SIF sync to be used. Normal FIFO_ISTR
signals are ignored.
0
3
Unused
Reserved for factory use.
0
2
Unused
Reserved for factory use.
0
output_delay(1:0)
Delays the output to the DACs from 0 to 3 DAC clock cycles.
00
5
4
1:0
20
Name
Default
Value
Function
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): DAC3283
DAC3283
www.ti.com
SLAS693A – MARCH 2010 – REVISED APRIL 2010
Register name: CONFIG3 – Address: 0x03, Default = 0x10
Register
Name
Address
Bit
CONFIG1
0x03
7
64cnt_ena
This enables resetting the alarms after 64 good samples with the goal of
removing unnecessary errors. For instance, when checking setup/hold
through the pattern checker test, there may initially be errors. Setting this
bit removes the need for a SIF write to clear the alarm register.
0
6
Unused
Reserved for factory use.
0
5
Unused
Reserved for factory use.
fifo_offset(2:0)
When the FIFO is reset, this is the value loaded into the FIFO read
pointer. With this value the initial difference between write and read
pointers can be controlled. This may be helpful in controlling the delay
through the device.
100
1
alarm_2away_ena
When asserted alarms from the FIFO that represent the write and read
pointers being 2 away are enabled.
0
0
alarm_1away_ena
When asserted alarms from the FIFO that represent the write and read
pointers being 1 away are enabled.
0
4:2
Name
Default
Value
Function
0
Register name: CONFIG4 – Address: 0x04, Default = 0xFF
Register
Name
Address
Bit
CONFIG4
0x04
7:4
Name
coarse_daca(3:0)
Default
Value
Function
Scales the DACA output current in 16 equal steps.
1111
VEXTIO
´ (coarse_daca/b + 1)
Rbias
3:0
coarse_dacb(3:0)
Scales the DACB output current in 16 equal steps.
1111
Register name: CONFIG5 – Address: 0x05, READ ONLY
Register
Name
Address
Bit
CONFIG5
0x05
7:0
Name
tempdata(7:0)
Default
Value
Function
This is the output from the chip temperature sensor. The value of this
register in two’s complement format represents the temperature in
degrees Celsius. This register must be read with a minimum SCLK
period of 1µs. (Read Only)
N/A
Register name: CONFIG6 – Address: 0x06, Default = 0x00
Register
Name
Address
CONFIG6
0x06
Bit
7
6:0
Name
Default
Value
Function
Unused
Reserved for factory use.
alarm_mask(6:0)
These bits control the masking of the alarm outputs. This means that the
ALARM_SDO pin will not be asserted if the appropriate bit is set. The
alarm will still show up in the CONFIG7 bits. (0=not masked, 1=
masked).
0
alarm_mask
Masked Alarm
6
alarm_from_zerochk
5
alarm_fifo_collision
4
reserved
3
alarm_from_iotest
2
not used (expansion)
1
alarm_fifo_2away
0
alarm_fifo_1away
0000000
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): DAC3283
21
DAC3283
SLAS693A – MARCH 2010 – REVISED APRIL 2010
www.ti.com
Register name: CONFIG7 – Address: 0x07, Default = 0x00 (WRITE TO CLEAR)
Register
Name
Address
Bit
CONFIG7
0x07
7
Unused
6
alarm_from_zerochk When this bit is asserted the FIFO write pointer has an all zeros
pattern in it. Since this pointer is a shift register, all zeros will cause
the input point to be stuck until the next sync. This alarm allows
checking for this condition.
0
5
alarm_fifo_collision
Alarm occurs when the FIFO pointers over/under run each other.
0
4
Reserved
When asserted the chip does 2X interpolation of the data.
0
3
alarm_from_iotest
This is asserted when the input data pattern does not match the
pattern in the iotest_pattern registers.
0
2
Unused
When asserted enables the data pattern checker operation.
0
1
alarm_fifo_2away
Alarm occurs with the read and write pointers of the FIFO are within 2
addresses of each other.
0
0
alarm_fifo_1away
Alarm occurs with the read and write pointers of the FIFO are within 1
address of each other.
0
Name
Function
Reserved for factory use.
Default
Value
0
Register name: CONFIG8 – Address: 0x08, Default = 0x00 (WRITE TO CLEAR)
Register
Name
Address
Bit
CONFIG8
0x08
7:0
Name
Function
iotest_results(7:0)
The values of these bits tell which bit in the word failed during the
pattern checker test.
Default
Value
0x00
Register name: CONFIG9 – Address: 0x09, Default = 0x7A
Register
Name
Address
Bit
CONFIG9
0x09
7:0
Name
Function
iotest_pattern0(7:0) This is dataword0 in the IO test pattern. It is used with the seven other
words to test the input data.
Default
Value
0x7A
Register name: CONFIG10 – Address: 0x0A, Default = 0xB6
Register
Name
Address
Bit
Name
Function
Default
Value
CONFIG10
0x0A
7:0
iotest_pattern1(7:0)
This is dataword1 in the IO test pattern. It is used with the seven other
words to test the input data.
0xB6
Register name: CONFIG11 – Address: 0x0B, Default = 0xEA
Register
Name
Address
Bit
Name
Function
Default
Value
CONFIG11
0x0B
7:0
iotest_pattern2(7:0)
This is dataword2 in the IO test pattern. It is used with the seven other
words to test the input data.
0xEA
Register name: CONFIG12 – Address: 0x0C, Default = 0x00
Register
Name
Address
Bit
Name
Function
Default
Value
CONFIG12
0x0C
7:0
iotest_pattern3(7:0)
This is dataword3 in the IO test pattern. It is used with the seven other
words to test the input data.
0x45
Register name: CONFIG13 – Address: 0x0D, Default = 0x1A
Register
Name
Address
Bit
Name
Function
Default
Value
CONFIG13
0x0D
7:0
iotest_pattern4(7:0)
This is dataword4 in the IO test pattern. It is used with the seven other
words to test the input data.
0x1A
22
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): DAC3283
DAC3283
www.ti.com
SLAS693A – MARCH 2010 – REVISED APRIL 2010
Register name: CONFIG14 – Address: 0x0E, Default = 0x16
Register
Name
Address
Bit
Name
Function
Default
Value
CONFIG14
0x0E
7:0
iotest_pattern5(7:0)
This is dataword5 in the IO test pattern. It is used with the seven other
words to test the input data.
0x16
Register name: CONFIG15 – Address: 0x0F, Default = 0xAA
Register
Name
Address
Bit
Name
Function
Default
Value
CONFIG15
0x0F
7:0
iotest_pattern6(7:0)
This is dataword6 in the IO test pattern. It is used with the seven other
words to test the input data.
0xAA
Register name: CONFIG16 – Address: 0x10, Default = 0xC6
Register
Name
Address
Bit
Name
Function
Default
Value
CONFIG16
0x10
7:0
iotest_pattern7(7:0)
This is dataword7 in the IO test pattern. It is used with the seven other
words to test the input data.
0XC6
Register name: CONFIG17 – Address: 0x11, Default = 0x24
Register
Name
Address
Bit
CONFIG17
0x11
7
Reserved
Reserved for factory use.
0
6
Reserved
Reserved for factory use.
0
5
Reserved
Reserved for factory use.
1
4
clk_alarm_mask
This bit controls the masking of the clock monitor alarm. This means
that the ALARM_SDO pin will not be asserted. The alarm will still show
up in the clk_alarm bit. (0=not masked, 1= masked).
0
tx_off_mask
This bit control the masking of the transmit enable alarm. This means
that the ALARM_SDO pin will not be asserted. The alarm will still show
up in the tx_off bit. (0=not masked, 1= masked).
0
2
Reserved
Reserved for factory use.
1
1
clk_alarm_ena
When asserted the DATACLK monitor alarm is enabled.
0
0
tx_off_ena
When asserted a clk_alarm event will automatically disable the DAC
outputs by setting them to midscale.
0
Name
Default
Value
Function
3
Register name: CONFIG18 – Address: 0x12, Default = 0x02
Register
Name
Address
Bit
CONFIG18
0x12
7:5
Reserved
Reserved for factory use.
000
4
Reserved
Reserved for factory use.
0
daca_complement
When asserted the output to the DACA is complemented. This allows to
effectively change the + and – designations of the LVDS data lines.
0
When asserted the output to the DACB is complemented. This allows to
effectively change the + and – designations of the LVDS data lines.
0
clkdiv_sync_ena
Enables the syncing of the clock divider using the OSTR signal or the
FRAME signal passed through the FIFO. This selection is determined
by multi_sync_sel in register CONFIG19. Syncing of the clock divider
should be done only during device initialization.
1
Unused
Reserved for factory use.
0
3
2
Name
dacb_complement
1
0
Default
Value
Function
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): DAC3283
23
DAC3283
SLAS693A – MARCH 2010 – REVISED APRIL 2010
www.ti.com
Register name: CONFIG19 – Address: 0x13, Default = 0x00
Register
Name
Address
Bit
CONFIG19
0x13
7
bequalsa
When asserted the DACA data is driven onto DACB.
0
6
aequalsb
When asserted the DACB data is driven onto DACA.
0
5
Reserved
Reserved for factory use.
0
4
Unused
Reserved for factory use.
0
3
Unused
Reserved for factory use.
0
2
Unused
Reserved for factory use.
0
1
multi_sync_sel
Selects the signal source for multiple device and clock divider
synchronization.
0
Name
multi_sync_sel
0
Default
Value
Function
rev
Sync Source
0
OSTR
1
FRAME through FIFO handoff
Reverse the input bits for the data word. MSB becomes LSB.
0
Register name: CONFIG20 – Address: 0x14, Default = 0x00 (CAUSES AUTOSYNC)
Register
Name
Address
Bit
CONFIG20
0x14
7:0
Function
Default
Value
Lower 8 bits of the DAC A offset correction. The offset is measured in
DAC LSBs. Writing this register causes an autosync to be
generated. This loads the values of all four qmc_offset registers
(CONFIG20-CONFIG23) into the offset block at the same time.
When updating the offset values CONFIG20 should be written last.
Programming any of the other three registers will not affect the
offset setting.
0X00
Name
qmc_offseta(7:0)
Register name: CONFIG21 – Address: 0x15, Default = 0x00
Register
Name
Address
Bit
CONFIG21
0x15
7:0
Name
Function
qmc_offsetb(7:0)
Lower 8 bits of the DAC B offset correction. The offset is measured in
DAC LSBs.
Default
Value
0X00
Register name: CONFIG22 – Address: 0x16, Default = 0x00
Register
Name
Address
Bit
CONFIG22
0x16
7:3
Name
Function
Default
Value
qmc_offseta(12:8)
Upper 5 bits of the DAC A offset correction.
2
Unused
Reserved for factory use.
00000
0
1
Unused
Reserved for factory use.
0
0
Unused
Reserved for factory use.
0
Register name: CONFIG23 – Address: 0x17, Default = 0x00
Register
Name
Address
Bit
Name
CONFIG23
0x17
7:3
24
Function
Default
Value
qmc_offsetb(12:8)
Upper 5 bits of the DAC B offset correction.
2
sif4_ena
When asserted the SIF interface becomes a 4 pin interface. The
ALARM pin is turned into a dedicated output for the reading of data.
0
1
clkpath_sleep_a
When asserted puts the clock path through DAC A to sleep. This is
useful for sleeping individual DACs. Even if the DAC is asleep the clock
needs to pass through it for the logic to work. However, if the chip is
being put into a power down mode, then all parts of the DAC can be
turned off.
0
0
clkpath_sleep_b
When asserted puts the clock path through DAC B to sleep.
0
Submit Documentation Feedback
00000
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): DAC3283
DAC3283
www.ti.com
SLAS693A – MARCH 2010 – REVISED APRIL 2010
Register name: CONFIG24 – Address: 0x18, Default = 0x83
Register
Name
Address
Bit
CONFIG24
0x18
7
Name
Default
Value
Function
tsense_ena
Turns on the temperature sensor when asserted.
1
clkrecv_sleep
When asserted the clock input receiver gets put into sleep mode. This
also affects the OSTR receiver.
0
5
Unused
Reserved for factory use.
0
4
Reserved
Reserved for factory use.
0
3
sleepb
When asserted DACB is put into sleep mode.
0
2
sleepa
When asserted DACA is put into sleep mode.
0
1
Reserved
Reserved for factory use.
1
0
Reserved
Reserved for factory use.
1
6
Register name: CONFIG25 – Address: 0x19, Default = 0x00
Register
Name
Address
Bit
CONFIG25
0x19
7:3
Reserved
Turns on the temperature sensor when asserted.
2
extref_ena
Allows the device to use an external reference or the internal
reference. (0=internal, 1=external)
0
1
Reserved
Reserved for factory use.
0
0
Reserved
Reserved for factory use.
0
Name
Default
Value
Function
00000
Register name: CONFIG26 – Address: 0x1a, Default = 0x00
Register
Name
Address
Bit
CONFIG26
0x1A
7:6
Reserved
Reserved for factory use.
00
5:4
Reserved
Reserved for factory use.
00
Unused
Reserved for factory use.
0
Reserved
Reserved for factory use.
000
3
2:0
Name
Default
Value
Function
Register name: CONFIG27 – Address: 0x1b, Default = 0x00 (CAUSES AUTOSYNC)
Register
Name
Address
Bit
CONFIG27
0x1B
7:0
Name
qmc_gaina(7:0)
Default
Value
Function
Lower 8 bits of the 11-bit DAC A QMC gain word. The upper 3 bits are
located in the CONFIG30 register. The full 11-bit qmc_gaina(10:0)
value is formatted as UNSIGNED with a range of 0 to 1.9990 and a
default gain of 1. The implied decimal point for the multiplication is
between bits 9 and 10. Writing this register causes an autosync to
be generated. This loads the values of all four qmc_phase/gain
registers (CONFIG27-CONFIG30) into the QMC block at the same
time. When updating the QMC phase and/or gain values
CONFIG27 should be written last. Programming any of the other
three registers will not affect the QMC settings.
0X00
Register name: CONFIG28 – Address: 0x1C, Default = 0x00
Register
Name
Address
Bit
CONFIG28
0x1C
7:0
Function
Default
Value
Lower 8 bits of the 11-bit DAC B QMC gain word. The upper 3 bits are
located in the CONFIG30 register. Refer to CONFIG27 for formatting.
0X00
Name
qmc_gainb(7:0)
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): DAC3283
25
DAC3283
SLAS693A – MARCH 2010 – REVISED APRIL 2010
www.ti.com
Register name: CONFIG29 – Address: 0x1D, Default = 0x00
Register
Name
Address
Bit
CONFIG29
0x1D
7:0
Name
qmc_phase(7:0)
Function
Lower 8-bits of the 10-bit QMC phase word. The upper 2 bits are in
the CONFIG30 register. The full 10-bit qmc_phase(9:0) word is
formatted as two's complement and scaled to occupy a range of
–0.125 to 0.12475 (note this value does not correspond to degrees)
and a default phase correction of 0. To accomplish QMC phase
correction, this value is multiplied by the current 'Q' sample, then
summed into the ‘I’ sample.
Default
Value
0X00
Register name: CONFIG30 – Address: 0x1E, Default = 0x24
Register
Name
Address
Bit
CONFIG30
0x1E
7:6
qmc_phase(9:8)
Upper 2 bits of qmc_phase. Defaults to zero.
00
5:3
qmc_gaina(10:8)
Upper 3 bits of qmc_gaina. Defaults to unity gain.
100
2:0
qmc_gainb(10:8)
Upper 3 bits of qmc_gainb. Defaults to unity gain.
100
Name
Function
Default
Value
Register name: VERSION31 – Address: 0x1F, Default = 0x52 (PARTIAL READ ONLY)
Register
Name
Address
Bit
VERSION31
0x1F
7
clk_alarm
This bit is set to '1' when DATACLK is stopped for 4 clock cycles.
Once set, the bit needs to be cleared by writing a '0'.
0
6
tx_off
This bit is set to '1' when the clk_alarm is triggered. When set the
DAC outputs are forced to mid-level. Once set, the bit needs to be
cleared by writing a '0'.
0
version(5:0)
A hardwired register that contains the version of the chip. (Read
Only)
5:0
26
Name
Default
Value
Function
Submit Documentation Feedback
010010
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): DAC3283
DAC3283
www.ti.com
SLAS693A – MARCH 2010 – REVISED APRIL 2010
SERIAL INTERFACE
The serial port of the DAC3283 is a flexible serial interface which communicates with industry standard
microprocessors and microcontrollers. The interface provides read/write access to all registers used to define the
operating modes of DAC3283. It is compatible with most synchronous transfer formats and can be configured as
a 3 or 4 pin interface by sif4_ena in register CONFIG23. In both configurations, SCLK is the serial interface input
clock and SDENB is serial interface enable. For 3 pin configuration, SDIO is a bidirectional pin for both data in
and data out. For 4 pin configuration, SDIO is data in only and ALARM_SDO is data out only. Data is input into
the device with the rising edge of SCLK. Data is output from the device on the falling edge of SCLK.
Each read/write operation is framed by signal SDENB (Serial Data Enable Bar) asserted low for 2 to 5 bytes,
depending on the data length to be transferred (1–4 bytes). The first frame byte is the instruction cycle which
identifies the following data transfer cycle as read or write, how many bytes to transfer, and what address to
transfer the data. Table 2 indicates the function of each bit in the instruction cycle and is followed by a detailed
description of each bit. Frame bytes 2 to 5 comprise the data transfer cycle.
Table 2. Instruction Byte of the Serial Interface
MSB
Bit
Description
7
R/W
LSB
6
N1
5
N0
4
A4
3
A3
2
A2
1
A1
0
A0
R/W
Identifies the following data transfer cycle as a read or write operation. A high indicates a read
operation from DAC3283 and a low indicates a write operation to DAC3283.
[N1:N0]
Identifies the number of data bytes to be transferred per Table 3. Data is transferred MSB first.
Table 3. Number of Transferred Bytes Within One
Communication Frame
[A4:A0]
N1
N0
Description
0
0
Transfer 1 Byte
0
1
Transfer 2 Bytes
1
0
Transfer 3 Bytes
1
1
Transfer 4 Bytes
Identifies the address of the register to be accessed during the read or write operation. For
multi-byte transfers, this address is the starting address. Note that the address is written to the
DAC3283 MSB first and counts down for each byte.
Figure 32 shows the serial interface timing diagram for a DAC3283 write operation. SCLK is the serial interface
clock input to DAC3283. Serial data enable SDENB is an active low input to DAC3283. SDIO is serial data in.
Input data to DAC3283 is clocked on the rising edges of SCLK.
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): DAC3283
27
DAC3283
SLAS693A – MARCH 2010 – REVISED APRIL 2010
www.ti.com
Instruction Cycle
Data Transfer Cycle
SDENB
SCLK
SDIO
rwb
N1
N0
-
A3
A2
A1
tS(SDENB)
A0
D7
D6
D5
D4
D3
D2
D1
D0
tSCLK
SDENB
SCLK
SDIO
tSCLKH
tS(SDIO) tH(SDIO)
tSCLKL
Figure 32. Serial Interface Write Timing Diagram
Figure 33 shows the serial interface timing diagram for a DAC3283 read operation. SCLK is the serial interface
clock input to DAC3283. Serial data enable SDENB is an active low input to DAC3283. SDIO is serial data in
during the instruction cycle. In 3 pin configuration, SDIO is data out from DAC3283 during the data transfer
cycle(s), while ALARM_SDO is in a high-impedance state. In 4 pin configuration, ALARM_SDO is data out from
DAC3283 during the data transfer cycle(s). At the end of the data transfer, ALARM_SDO will output low on the
final falling edge of SCLK until the rising edge of SDENB when it will 3-state.
Instruction Cycle
Data Transfer Cycle
SDENB
SCLK
SDIO
rwb
N1
N0
-
A3
A2
A1
ALARM_
SDO
A0
D7
D6
D5
D4
D3
D2
D1
D0
3-pin interface
D7
D6
D5
D4
D3
D2
D1
D0
4-pin interface
SDENB
SCLK
SDIO or
ALARM_SDO
Data n
Data n-1
td(Data)
Figure 33. Serial Interface Read Timing Diagram
28
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): DAC3283
DAC3283
www.ti.com
SLAS693A – MARCH 2010 – REVISED APRIL 2010
DATA INTERFACE
The DAC3283 has a single 8-bit LVDS bus that accepts dual, 16-bit data input in byte-wide format. Data into the
DAC3283 is formatted according to the diagram shown in Figure 34 where index 0 is the data LSB and index 15
is the data MSB. The data is sampled by DATACLK, a double data rate (DDR) clock.
The FRAME signal is required to indicate the beginning of a frame. The frame signal can be either a pulse or a
periodic signal where the frame period corresponds to 8 samples. The pulse-width (t(FRAME)) needs to be at least
equal to ½ of the DATACLK period. FRAME is sampled by a rising edge in DATACLK.
The setup and hold requirements listed in the specifications tables must be met to ensure proper sampling.
SAMPLE 0
D[7:0]P/N
FRAMEP/N
I0
[15:8]
I0
[7:0]
Q0
[15:8]
SAMPLE 1
Q0
[7:0]
I1
[15:8]
I1
[7:0]
Q1
[15:8]
Q1
[7:0]
t(FRAME)
DATACLKP /N
(DDR)
Figure 34. Byte-Wide Data Transmission Format
INPUT FIFO
The DAC3283 includes a 2-channel, 16-bits wide and 8-samples deep input FIFO which acts as an elastic buffer.
The purpose of the FIFO is to absorb any timing variations between the input data and the internal DAC data
rate clock such as the ones resulting from clock-to-data variations from the data source.
Figure 35 shows a simplified block diagram of the FIFO.
Clock Handoff
Input Side
Clocked by DATACLK
Initial
Position
8-bit
8-bit
Frame Align
Q-data, 16-bit
Data[7:0]
32-bit
0
Sample 0
I0 [15:0], Q0 [15:0]
0
1
Sample 1
I1 [15:0], Q1 [15:0]
1
2
Sample 2
I2 [15:0], Q2 [15:0]
2
3
Sample 3
I3 [15:0], Q3 [15:0]
3
4
Sample 4
I4 [15:0], Q4 [15:0]
4
5
Sample 5
I5 [15:0], Q5 [15:0]
5
6
Sample 6
I6 [15:0], Q6 [15:0]
6
7
Sample 7
I7 [15:0], Q7 [15:0]
7
FRAME
Write Pointer Reset
32-bit
0…7
Read Pointer
I-data, 16-bit
0…7
Write Pointer
Data[15:8]
D[7:0]
Output Side
Clocked by FIFO Out Clock
(DACCLK/Interpolation Factor)
FIFO:
2 x 16-bits wide
8-samples deep
x2
Two cycles, one for I-data and another
for Q-data
16-bit
FIFO I Output
FIFO Q Output
16-bit
Initial
Position
Read Pointer Reset
Figure 35. DAC3283 FIFO Block Diagram
Data is written to the device 8-bits at a time on the rising and falling edges of DATACLK. In order to form a
complete 32-bit wide sample (16-bit I-data and 16-bit Q-data) two DATACLK periods are required as shown in
Figure 36. Each 32-bit wide sample is written into the FIFO at the address indicated by the write pointer.
Similarly, data from the FIFO is read by the FIFO Out Clock 32-bits at a time from the address indicated by the
read pointer. The FIFO Out Clock is generated internally from the DACCLK signal and its rate is equal to
DACCLK/Interpolation. Each time a FIFO write or FIFO read is done the corresponding pointer moves to the next
address.
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): DAC3283
29
DAC3283
SLAS693A – MARCH 2010 – REVISED APRIL 2010
www.ti.com
The reset position for the FIFO read and write pointers is set by default to addresses 0 and 4 as shown in
Figure 35. This offset gives optimal margin within the FIFO. The default read pointer location can be set to
another value using fifo_offset(2:0) in register CONFIG3. Under normal conditions data is written-to and
read-from the FIFO at the same rate and consequently the write and read pointer gap remains constant. If the
FIFO write and read rates are different, the corresponding pointers will be cycling at different speeds which could
result in pointer collision. Under this condition the FIFO attempts to read and write data from the same address at
the same time which will result in errors and thus must be avoided.
The FRAME signal besides acting as a frame indicator can also used to reset the FIFO pointers to their initial
location. Unlike Data, the FRAME signal is latched only on the rising edges of DATACLK. When a rising edge
occurs on FRAME, the pointers will return to their original position. The write pointer is always set back to
position 0 upon reset. The read pointer reset position is determined by fifo_offset (address 4 by default).
The reset can be done periodically or only once during initialization as the pointer automatically returns to the
initial position when the FIFO has been filled. To enable a single reset, fifo_reset_ena (CONFIG0, bit 5) must be
set to 0 after initialization.
LVDS Pairs (Data Source)
D[7:0]P/N
Q3[15:8]
Q3[7:0]
I4[15:8]
I4[7:0]
Q4[15:8]
Q4[7:0]
I5[15:8]
I5[7:0]
Q5[15:8]
Q5[7:0]
I6[15:8]
I6[7:0]
Q6[15:8]
Q6[7:0]
I7[15:8]
I7[7:0]
Q7[15:8]
Write sample 4 to FIFO (32-bits)
Write I4[7:0] (8-bits) to Write Q4[7:0] (8-bits) to
DAC on falling edge
DAC on falling edge
ts(DATA )
ts(DATA )
DATACLKP /N
(DDR)
th(DATA )
Write I4[15:8] (8-bits) to Write Q4[15:8] (8-bits) to
DAC on rising edge
DAC on rising edge
ts(DATA )
FRAMEP/N
th(DATA )
th(DATA )
Resets write pointer to position 0
Figure 36. FIFO Write Description
FIFO ALARMS
The FIFO only operates correctly when the write and read pointers are positioned properly. If either pointer over
or under runs the other, samples will be duplicated or skipped. To prevent this, register CONFIG7 can be used to
track three FIFO related alarms:
• alarm_fifo_2away. Occurs when the pointers are within two addresses of each other.
• alarm_fifo_1away. Occurs when the pointers are within one address of each other.
• alarm_fifo_collision. Occurs when the pointers are equal to each other.
These three alarm events are generated asynchronously with respect to the clocks and can be accessed either
through CONFIG7 or through the ALARM_SDO pin.
FIFO MODES OF OPERATION
The DAC3283 FIFO can be completely bypassed through register CONFIG1. The register configuration for each
mode is described in Table 4.
Register
Control Bits
CONFIG1
fifo_ena, fifo_reset_ena, multi_sync_ena
Table 4. FIFO Operation Modes
CONFIG1FIFO Bits
30
FIFO Mode
fifo_ena
fifo_reset_ena
Enabled
1
1
1
Bypass
0
X
X
Submit Documentation Feedback
multi_sync_ena
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): DAC3283
DAC3283
www.ti.com
SLAS693A – MARCH 2010 – REVISED APRIL 2010
a) Enabled Mode
This is the recommended mode of operation for the DAC3283. In FIFO enabled mode, the FIFO is active and
can be reset continuously or only once during initialization. To reset only once fifo_reset_ena must be set to 0
after initialization.
b) Bypass Mode
In FIFO bypass mode, the FIFO block is not used. As a result the input data is handed off from the DATACLK to
the DACCLK domain without any compensation. In this mode the relationship between DATACLK and DACCLK
(t_align) is critical and used as a synchronizing mechanism for the internal logic. Due to the t_align constraint it is
highly recommended that a clock synchronizer device such as Texas Instruments’ CDCM7005 or CDCE62005 is
used to provide both clock inputs. In bypass mode the pointers have no effect on the data path or handoff.
DATA PATTERN CHECKER
The DAC3283 incorporates a simple pattern checker test in order to determine errors in the data interface. The
test mode is enabled by asserting iotest_ena in register CONFIG1. In test mode the analog outputs are
deactivated regardless of the state of TXENABLE.
The data pattern key used for the test is 8 words long and is specified by the contents of iotest_pattern[0:7] in
registers CONFIG9 through CONFIG16. The data pattern key can be modified by changing the contents of these
registers.
The first word in the test frame is determined by a rising edge transition in FRAMEP/N. The test mode
determines if one or more words were received incorrectly by comparing the received data against the data
pattern key. The bits in iotest_results(7:0) in register CONFIG8 indicate which words were received incorrectly.
Furthermore, an error condition will trigger the alarm_from_iotest bit in register CONFIG7. Once set, the
alarm_from_iotest bit must be reset through the serial interface to allow further testing. Alternatively, the
64cnt_ena bit in register CONFIG3 can be enabled to reset the alarms automatically after 64 good samples
without the need for a SIF write to clear the alarm.
DATACLK MONITOR
The DAC3283 incorporates a clock monitor to determine if DATACLK is present. A missing DATACLK may result
in unexpected DAC outputs. The clock monitor circuit issues two alarms if a missing DATACLK event is detected:
clk_alarm (bit 7 in register VERSION31) and tx_off (bit 6 in register VERSION31). When tx_off is set the
DAC3283 outputs are automatically disabled by setting data to mid-scale.
Both alarms are set by default to trigger the ALARM_SDO pin. This functionality can be disabled by masking the
alarms in register CONFIG17. Once set, the alarms must be reset through the serial interface by writing a 0 to
the alarm bits. The clock monitor alarms can be disabled by setting clk_alarm_ena or tx_off_ena in register
CONFIG17 to 0.
The clock monitoring function is implemented as follows:
• Power up the device using the recommended power-up sequence.
• Clear clk_alarm and tx_off by writing a 1 and then a 0.
• Unmask the alarms in register CONFIG17.
• In the case of an alarm event, the ALARM_SDO pin will trigger.
• Read registers CONFIG7 and VERSION31 registers to determine which alarm triggered the ALARM_SDO
pin.
• In the case clk_alarm and/or tx_off are set, a DATACLK interruption has occurred.
• Re-apply DATACLK and clear clk_alarm by writing 1 and then 0.
• Re-read clk_alarm to verify the clock loss event has not re-triggered the alarm.
• Keep clearing and reading clk_alarm until no error is reported.
• If enabled re-synchronize the FIFO.
• Clear the tx_off alarm by writing 1 and the 0. This will re-enable the DAC outputs.
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): DAC3283
31
DAC3283
SLAS693A – MARCH 2010 – REVISED APRIL 2010
www.ti.com
FIR FILTERS
Figure 37 and Figure 38 show the magnitude spectrum response for the FIR0 and FIR1 interpolating half-band
filters where fIN is the input data rate to the FIR filter. Figure 39 and Figure 40 show the composite filter response
for 2x and 4x interpolation. The transition band for all the interpolation settings is from 0.4 to 0.6 x fDATA (the input
data rate to the device) with < 0.002dB of pass-band ripple and > 85dB stop-band attenuation.
20
20
0
0
-20
-20
-40
-40
Magnitude - dB
Magnitude - dB
The filter taps for all digital filters are listed in Table 5.
-60
-80
-100
-100
-120
-140
-140
0
0.1
0.2 0.3
0.4 0.5 0.6
f/fIN
0.7
0.8 0.9
-160
0
1
0.1
0.2 0.3
0.4 0.5 0.6
f/fIN
0.7
0.8 0.9
Figure 37. Magnitude Spectrum for FIR0
Figure 38. Magnitude Spectrum for FIR1
20
20
0
0
-20
-20
-40
-40
Magnitude - dB
Magnitude - dB
-80
-120
-160
-60
-80
-100
-80
-100
-120
-140
-140
0.1
0.2 0.3
0.4 0.5 0.6
f/fDATA
0.7
0.8 0.9
1
Figure 39. 2x Interpolation Composite Response
1
-60
-120
-160
0
32
-60
-160
0
0.1
0.2 0.3
0.4 0.5 0.6
f/fDATA
0.7
0.8 0.9
1
Figure 40. 4x Interpolation Composite Response
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): DAC3283
DAC3283
www.ti.com
SLAS693A – MARCH 2010 – REVISED APRIL 2010
Table 5. FIR Filter Coefficients
FIR0
2x Interpolating
Half-band Filter
FIR1
2x Interpolating
Half-Band Filter
59 Taps
23 Taps
4
4
–2
0
0
0
–12
–12
17
0
0
0
28
28
–75
0
0
0
–58
–58
238
0
0
0
108
108
–660
0
0
0
–188
–188
2530
0
0
4096 (1)
308
308
2530
0
0
0
–483
–483
–660
0
0
0
734
734
238
0
0
0
–1091
–1091
–75
0
0
0
1607
1607
17
0
0
0
–2392
–2392
–2
0
0
3732
3732
0
0
–6681
–6681
0
0
20768
20768
32768 (1)
(1)
Center taps are highlighted in BOLD.
COARSE MIXER
The DAC3283 has a coarse mixer block capable of shifting the input signal spectrum by the fixed mixing
frequencies fS/2 or fS/4. The coarse mixing function is built into the interpolation filters and thus FIR0 (2x
interpolation) or FIR0 and FIR1 (4x interpolation) must be enabled to use it.
Treating channels A and B as a complex vector of the form I(t) + j Q(t), where I(t) = A(t) and Q(t) = B(t), the
outputs of the coarse mixer, AOUT(t) and BOUT(t) are equivalent to:
AOUT(t) = A(t)cos(2pfCMIXt) – B(t)sin(2pfCMIXt)
BOUT(t) = A(t)sin(2pfCMIXt) + B(t)cos(2pfCMIXt)
where fCMIX is the fixed mixing frequency selected by mixer_func(1:0). For fS/2, +fS/4 and –fS/4 the above
operations result in the simple mixing sequences shown in Table 6.
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): DAC3283
33
DAC3283
SLAS693A – MARCH 2010 – REVISED APRIL 2010
www.ti.com
Table 6. Coarse Mixer Sequences
Mode
mixer_func(1:0)
Mixing Sequence
Normal (Low Pass, No Mixing)
00
AOUT = { +A, +A , +A, +A }
BOUT = { +B, +B , +B, +B }
fS/2
01
AOUT = { +A, –A , +A, –A }
BOUT = { +B, -B , +B, -B }
+fS/4
10
AOUT = { +A, -B , –A, +B }
BOUT = { +B, +A , –B, –A }
–fS/4
11
AOUT = { +A, +B , –A, –B }
BOUT = { +B, –A , –B, +A }
(x2 Bypass)
FIR
x2
B Data In
A Data Out
Coarse Mixer
x2
A Data In
B Data Out
Block Diagram
A Mix In
0
A Mix Out
1
0 1
1 -1
1
B Mix In
B Mix Out
0
0 1
1 -1
mixer_func(1:0)
Mix Sequencer
Figure 41. Coarse Mixers Block Diagram
The coarse mixer in the DAC3283 treats the A and B inputs as complex input data and for most mixing
frequencies produces a complex output. Only when the mixing frequency is set to fS/2 the A and B channels can
be maintained isolated as shown in Table 6. In this case the two channels are upconverted as independent
signals. By setting the mixer to fS/2 the interpolation filter outputs are inverted thus behaving as a high-pass filter.
Table 7. Dual-Channel Real Upconversion Options
(1)
34
FIR MODE
INPUT FREQUENCY (1)
OUTPUT FREQUENCY (1)
SIGNAL BANDWIDTH (1)
Low Pass
0.0 to 0.4 × fDATA
0.0 to 0.4 × fDATA
0.4 × fDATA
No
High Pass
0.0 to 0.4 × fDATA
0.6 to 1.0 × fDATA
0.4 × fDATA
Yes
SPECTRUM INVERTED?
fDATA is the input data rate of each channel after de-interleaving.
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): DAC3283
DAC3283
www.ti.com
SLAS693A – MARCH 2010 – REVISED APRIL 2010
QUADRATURE MODULATION CORRECTION (QMC)
The Quadrature Modulator Correction (QMC) block provides a means for adjusting the gain and phase of the
complex signal. At a quadrature modulator output, gain and phase imbalances result in an undesired sideband
signal.
The block diagram for the QMC is shown in Figure 42. The QMC block contains 3 programmable parameters:
qmc_gaina(10:0), qmc_gainb(10:0) and qmc_phase(9:0).
Registers qmc_gaina(10:0) and qmc_gainb(10:0) control the I and Q path gains and are 11 bit values with a
range of 0 to approximately 2. This value is used to scale the signal range. Register qmc_phase(9:0) controls the
phase imbalance between I and Q and is a 10-bit value that ranges from –1/8 to approximately +1/8. This value
is multiplied by each Q sample then summed into the I sample path. This operation is a simplified approximation
of a true phase rotation and covers the range from –3.75 to +3.75 degrees in 1024 steps.
A write to register CONFIG27 is required to load the gain and phase values (CONFIG27-CONFIG30) into the
QMC block simultaneously. When updating the gain and/or phase values CONFIG27 should be written last.
Programming any of the other three registers will not affect the gain and phase settings.
qmc_gaina (10:0)
11
16
A Data In
x
S
16
A Data Out
10
x
qmc_phase (9:0)
x
B Data In
16
16
B Data Out
11
qmc_gainb (10:0)
Figure 42. QMC Block Diagram
DIGITAL OFFSET CONTROL
The qmc_offseta(12:0) and qmc_offsetb(12:0) values in registers CONFIG20 through CONFIG23 can be used to
independently adjust the A and B path DC offsets. Both offset values are in represented in 2s-complement format
with a range from –4096 to 4095.
Note that a write to register CONFIG20 is required to load the values of all four qmc_offset registers
(CONFIG20-CONFIG23) into the offset block simultaneously. When updating the offset values CONFIG20 should
be written last. Programming any of the other three registers will not affect the offset setting.
The offset value adds a digital offset to the digital data before digital-to-analog conversion. Since the offset is
added directly to the data it may be necessary to back off the signal to prevent saturation. Both data and offset
values are LSB aligned.
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): DAC3283
35
DAC3283
SLAS693A – MARCH 2010 – REVISED APRIL 2010
www.ti.com
qma_offset
{-4096, -4095, … , 4095}
13
16
S
A Data In
16
S
B Data In
13
16
A Data Out
16
B Data Out
qmb_offset
{-4096, -4095, … , 4095}
Figure 43. Digital Offset Block Diagram
TEMPERATURE SENSOR
The DAC3283 incorporates a temperature sensor block which monitors the temperature by measuring the
voltage across 2 transistors. The voltage is converted to an 8-bit digital word using a successive-approximation
(SAR) analog to digital conversion process. The result is scaled, limited and formatted as a twos complement
value representing the temperature in degrees Celsius.
The sampling is controlled by the serial interface signals SDENB and SCLK. If the temperature sensor is enabled
(tsense_ena = 1 in register CONFIG24) a conversion takes place each time the serial port is written or read. The
data is only read and sent out by the digital block when the temperature sensor is read in register CONFIG5. The
conversion uses the first eight clocks of the serial clock as the capture and conversion clock, the data is valid on
the falling eighth SCLK. The data is then clocked out of the chip on the rising edge of the ninth SCLK. No other
clocks to the chip are necessary for the temperature sensor operation. As a result the temperature sensor is
enabled even when the device is in sleep mode.
In order for the process described above to operate properly, the serial port read from CONFIG5 must be done
with an SCLK period of at least 1µs. If this is not satisfied the temperature sensor accuracy is greatly reduced.
POWER-UP SEQUENCE
The following startup sequence is recommended to power-up the DAC3283:
• Set TXENABLE low.
• Supply 1.8V to DACVDD18, DIGVDD18, CLKVDD18 and VFUSE simultaneously and 3.3V to AVDD33.
Within AVDD33 the multiple AVDD33 pins should be powered up simultaneously. The 1.8V and 3.3V supplies
can be powered up simultaneously or in any order.
There are no specific requirements on the ramp rate for the supplies.
• Provide all LVPECL inputs: DACCLKP/N and if used OSTRP/N.
• Program the SIF registers.
• Provide all LVDS inputs (D[7:0]P/N, DATACLKP/N and FRAMEP/N) simultaneously.
• Sync the clock dividers and FIFO. After a FRAMEP/N low-to-high transition, clock divider syncing must be
disabled by setting clkdiv_sync_ena (CONFIG18, bit 1) to 0. Optionally, disable FIFO syncing by setting
fifo_reset_ena (CONFIG0, bit 5) and multi_sync_ena (CONFIG0, bit 4) to 0. Except when in Multi-DAC
operation it is recommended to sync the DACs and their FIFO’s only once during initialization.
• Enable transmit of data by asserting the TXENABLE pin.
SLEEP MODES
The DAC3283 features independent sleep control of each DAC (sleepa and sleepb), their corresponding clock
path (clkpath_sleep_a and clkpath_sleep_b) as well as the clock input receiver of the device (clkrecv_sleep). The
sleep control of each of these components is done through the SIF interface and is enabled by setting a 1 to the
corresponding sleep register.
36
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): DAC3283
DAC3283
www.ti.com
SLAS693A – MARCH 2010 – REVISED APRIL 2010
Complete power down of the device is set by setting all of these components to sleep. Under this mode the
supply power consumption is reduced to 15mW. Power-up time in this case will be in the milliseconds range.
Alternatively for those applications were power-up and power-down times are critical it is recommended to only
set the DACs to sleep through the sleepa and sleepb registers. In this case both the sleep and wake-up times
are only 90µs.
LVPECL INPUTS
Figure 44 shows an equivalent circuit for the DAC input clock (DACCLP/N) and the output strobe clock
(OSTRP/N).
CLKVDD
500 W
DACCLKP
OSTRP
Note: Input common mode level is
approximately 1/2*CLKVDD18,
or 0.9V nominal.
2 kW
2 kW
DACCLKN
OSTRN
500 W
GND
Figure 44. DACCLKP/N and OSTRP/N Equivalent Input Circuit
Figure 45 shows the preferred configuration for driving the CLKIN/CLKINC input clock with a differential
ECL/PECL source.
0.1 mF
CLKIN
Differential +
ECL
or
(LV)PECL
source
-
CAC
100 W
CLKINC
0.1 mF
150 W
RT
150 W
Figure 45. Preferred Clock Input Configuration with a Differential ECL/PECL Clock Source
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): DAC3283
37
DAC3283
SLAS693A – MARCH 2010 – REVISED APRIL 2010
www.ti.com
LVDS INPUTS
The D[7:0]P/N, DATACLKP/N and FRAMEP/N LVDS pairs have the input configuration shown in Figure 46.
Figure 47 shows the typical input levels and common-move voltage used to drive these inputs.
To Adjacent
LVDS Input
50
D[7:0]P,
DATACLKP ,
FRAMEP
100 pF
Total
LVDS
Receiver
50
Ref Note (1)
D[7:0]N,
DATACLKN ,
FRAMEN
To Adjacent
LVDS Input
Note (1): RCENTER node common
to the D[7:0]P/N, DATACLKP /N and
FRAMEP/N receiver inputs
Figure 46. D[7:0]P/N, DATACLKP/N and FRAMEP/N LVDS Input Configuration
Example
D[7:0]P,
DATACLKP ,
FRAMEP
LVDS
Receiver
100
VA,B
VCOM =
(VA+VB)/2
DAC3283
VA
1.40 V
VB
1.00 V
400 mV
VA,B
0V
VA
D[7:0]N,
DATACLKN ,
FRAMEN
VB
-400 mV
GND
1
Logical Bit
Equivalent
0
Figure 47. LVDS Data (D[7:0]P/N, DATACLKP/N, FRAMEP/N Pairs) Input Levels
Table 8. Example LVDS Data Input Levels
APPLIED VOLTAGES
38
RESULTING
DEFERENTIAL
VOLTAGE
RESULTING
COMMON-MODE
VOLTAGE
VA,B
VCOM
1.2 V
VA
VB
1.4 V
1.0 V
400 mV
1.0 V
1.4 V
–400 mV
1.2 V
0.8 V
400 mV
0.8 V
1.2 V
–400 mV
LOGICAL BIT BINARY
EQUIVALENT
1
0
1.0 V
Submit Documentation Feedback
1
0
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): DAC3283
DAC3283
www.ti.com
SLAS693A – MARCH 2010 – REVISED APRIL 2010
CMOS DIGITAL INPUTS
Figure 48 shows a schematic of the equivalent CMOS digital inputs of the DAC3283. SDIO, SCLK and
TXENABLE have pull-down resistors while SDENB has a pull-up resistors internal to the DAC3283. See the
specification table for logic thresholds. The pull-up and pull-down circuitry is approximately equivalent to 100kΩ.
DIGVDD18
DIGVDD18
SDIO
SCLK
TXENABLE
internal
digital in
internal
digital in
SDENB
GND
GND
Figure 48. CMOS/TTL Digital Equivalent Input
REFERENCE OPERATION
The DAC3283 uses a bandgap reference and control amplifier for biasing the full-scale output current. The
full-scale output current is set by applying an external resistor RBIAS to pin BIASJ. The bias current IBIAS through
resistor RBIAS is defined by the on-chip bandgap reference voltage and control amplifier. The default full-scale
output current equals 16 times this bias current and can thus be expressed as:
IOUTFS = 16 × IBIAS = 16 × VEXTIO / RBIAS
Each DAC has a 4-bit coarse gain control via coarse_daca(3:0) and coarse_dacb (3:0) in the CONFIG4
register. Using gain control, the IOUTFS can be expressed as::
IOUTAFS = (DACA_gain + 1) × IBIAS = (DACA_gain + 1) × VEXTIO / RBIAS
IOUTBFS = (DACB_gain + 1) x IBIAS = (DACB_gain + 1) x VEXTIO / RBIAS
where VEXTIO is the voltage at terminal EXTIO. The bandgap reference voltage delivers an accurate voltage of
1.2V. This reference is active when extref_ena = '0' in CONFIG25. An external decoupling capacitor CEXT of
0.1µF should be connected externally to terminal EXTIO for compensation. The bandgap reference can
additionally be used for external reference operation. In that case, an external buffer with high impedance input
should be applied in order to limit the bandgap load current to a maximum of 100nA. The internal reference can
be disabled and overridden by an external reference by setting the CONFIG25 extref_ena control bit. Capacitor
CEXT may hence be omitted. Terminal EXTIO thus serves as either input or output node.
The full-scale output current can be adjusted from 20mA down to 2mA by varying resistor RBIAS or changing the
externally applied reference voltage. The internal control amplifier has a wide input range, supporting the
full-scale output current range of 20dB.
DAC TRANSFER FUNCTION
The CMOS DAC’s consist of a segmented array of NMOS current sinks, capable of sinking a full-scale output
current up to 20mA. Differential current switches direct the current to either one of the complementary output
nodes IOUT1 or IOUT2. (DACA = IOUTA1 or IOUTA2 and DACB = IOUTB1 or IOUTB2.) Complementary output
currents enable differential operation, thus canceling out common mode noise sources (digital feed-through,
on-chip and PCB noise), dc offsets, even order distortion components, and increasing signal output power by a
factor of two.
The full-scale output current is set using external resistor RBIAS in combination with an on-chip bandgap voltage
reference source (+1.2V) and control amplifier. Current IBIAS through resistor RBIAS is mirrored internally to
provide a maximum full-scale output current equal to 16 times IBIAS.
The relation between IOUT1 and IOUT2 can be expressed as:
IOUT1 = – IOUTFS – IOUT2
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): DAC3283
39
DAC3283
SLAS693A – MARCH 2010 – REVISED APRIL 2010
www.ti.com
Current flowing into a node is denoted as – current and current flowing out of a node as + current. Since the
output stage is a current sink the current can only flow from AVDD into the IOUT1 and IOUT2 pins. The output
current flow in each pin driving a resistive load can be expressed as:
IOUT1 = IOUTFS × (65535 – CODE) / 65536
IOUT2 = IOUTFS × CODE / 65536
where CODE is the decimal representation of the DAC data input word.
For the case where IOUT1 and IOUT2 drive resistor loads RL directly, this translates into single ended voltages
at IOUT1 and IOUT2:
VOUT1 = AVDD – | IOUT1 | × RL
VOUT2 = AVDD – | IOUT2 | × RL
Assuming that the data is full scale (65536 in offset binary notation) and the RL is 25 Ω, the differential voltage
between pins IOUT1 and IOUT2 can be expressed as:
VOUT1 = AVDD – | –0 mA | × 25 Ω = 3.3 V
VOUT2 = AVDD – | –20 mA | × 25 Ω = 2.8 V
VDIFF = VOUT1 – VOUT2 = 0.5 V
Note that care should be taken not to exceed the compliance voltages at node IOUT1 and IOUT2, which would
lead to increased signal distortion.
ANALOG CURRENT OUTPUTS
Figure 49 shows a simplified schematic of the current source array output with corresponding switches.
Differential switches direct the current of each individual NMOS current source to either the positive output node
IOUT1 or its complementary negative output node IOUT2. The output impedance is determined by the stack of
the current sources and differential switches, and is typically >300 kΩ in parallel with an output capacitance of 5
pF.
The external output resistors are referenced to an external ground. The minimum output compliance at nodes
IOUT1 and IOUT2 is limited to AVDD – 0.5 V, determined by the CMOS process. Beyond this value, transistor
breakdown may occur resulting in reduced reliability of the DAC3283 device. The maximum output compliance
voltage at nodes IOUT1 and IOUT2 equals AVDD + 0.5 V. Exceeding the minimum output compliance voltage
adversely affects distortion performance and integral non-linearity. The optimum distortion performance for a
single-ended or differential output is achieved when the maximum full-scale signal at IOUT1 and IOUT2 does not
exceed 0.5 V.
AVDD
R LOAD
IOUT1
R LOAD
IOUT2
S(1)
S(N)
S(2)
S(1)C
S(2)C
S(N)C
...
Figure 49. Equivalent Analog Current Output
40
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): DAC3283
DAC3283
www.ti.com
SLAS693A – MARCH 2010 – REVISED APRIL 2010
The DAC3283 can be easily configured to drive a doubly terminated 50Ω cable using a properly selected RF
transformer. Figure 50 and Figure 51 show the 50Ω doubly terminated transformer configuration with 1:1 and 4:1
impedance ratio, respectively. Note that the center tap of the primary input of the transformer has to be
connected to AVDD to enable a dc current flow. Applying a 20 mA full-scale output current would lead to a 0.5
VPP for a 1:1 transformer, and a 1 VPP output for a 4:1 transformer. The low dc-impedance between IOUT1 or
IOUT2 and the transformer center tap sets the center of the ac-signal at AVDD, so the 1 VPP output for the 4:1
transformer results in an output between AVDD + 0.5 V and AVDD – 0.5 V.
AVDD (3.3 V)
50 W
1:1
IOUT1
RLOAD
100 W
50 W
IOUT2
50 W
AVDD (3.3 V)
Figure 50. Driving a Doubly-Terminated 50-Ω Cable Using a 1:1 Impedance Ratio Transformer
AVDD (3.3 V)
100 W
4 :1
IOUT1
RLOAD
50 W
IOUT2
100 W
AVDD (3.3 V)
Figure 51. Driving a Doubly-Terminated 50-Ω Cable Using a 4:1 Impedance Ratio Transformer
PASSIVE INTERFACE TO ANALOG QUADRATURE MODULATORS
A common application in communication systems is to interface the DAC to an IQ modulator like the TRF3703
family of modulators from Texas Instruments. The input of the modulator is generally of high impedance and
requires a specific common-mode voltage. A simple resistive network can be used to maintain 50Ω load
impedance for the DAC3283 and also provide the necessary common-mode voltages for both the DAC and the
modulator.
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): DAC3283
41
DAC3283
SLAS693A – MARCH 2010 – REVISED APRIL 2010
www.ti.com
Vin ~ Varies
Vout ~ 2.8 to 3.8 V
I1
Signal Conditioning
IOUTA1
IOUTA2
IOUTB1
IOUTB2
I2
S
Q1
RF
Q2
Quadrature modulator
Figure 52. DAC to Analog Quadrature Modulator Interface
The DAC3283 has a maximum 20mA full-scale output and a voltage compliance range of AVDD ± 0.5 V. The
TRF3703 IQ modulator family can be operated at three common-mode voltages: 1.5V, 1.7V, and 3.3V.
Figure 53 shows the recommended passive network to interface the DAC3283 to the TRF3703-17 which has a
common mode voltage of 1.7V. The network generates the 3.3V common mode required by the DAC output and
1.7V at the modulator input, while still maintaining 50Ω load for the DAC.
V1
R1
I
I
R2
R3
DAC3283
TRF3703-17
V2
R3
R2
/I
/I
R1
V1
Figure 53. DAC3283 to TRF3703-17 Interface
If V1 is set to 5V and V2 is set to -5V, the corresponding resistor values are R1 = 57Ω, R2 = 80Ω, and R3 =
336Ω. The loss developed through R2 is about -1.86 dB. In the case where there is no –5V supply available and
V2 is set to 0V, the resistor values are R1 = 66Ω, R2 = 101Ω, and R3 = 107Ω. The loss with these values is
–5.76dB.
Figure 54 shows the recommended network for interfacing with the TRF3703-33 which requires a common mode
of 3.3V. This is the simplest interface as there is no voltage shift. Because there is no voltage shift there is any
loss in the network. With V1 = 5V and V2 = 0V, the resistor values are R1 = 66Ω and R3 = 208Ω.
42
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): DAC3283
DAC3283
www.ti.com
SLAS693A – MARCH 2010 – REVISED APRIL 2010
V1
R1
I
I
R3
DAC3283
TRF3703-33
V2
R3
/I
/I
R1
V1
Figure 54. DAC3283 to TRF3703-33 Interface
In most applications a baseband filter is required between the DAC and the modulator to eliminate the DAC
images. This filter can be placed after the common-mode biasing network. For the DAC to modulator network
shown in Figure 55, R2 and the filter load R4 need to be considered into the DAC impedance. The filter has to be
designed for the source impedance created by the resistor combination of R3 // (R2+R1). The effective
impedance seen by the DAC is affected by the filter termination resistor resulting in R1 // (R2+R3 // (R4/2)).
V1
R1
R2
I
R3
V2
DAC3283
Filter
R4
TRF3703
R3
R2
/I
R1
V1
Figure 55. DAC3283 to Modulator Interface with Filter
Factoring in R4 into the DAC load, a typical interface to the TRF3703-17 with V1 = 5V and V2 = 0V results in the
following values: R1 = 72Ω, R2 = 116Ω, R3 = 124Ω and R4 = 150Ω. This implies that the filter needs to be
designed for 75Ω input and output impedance (single-ended impedance). The common mode levels for the DAC
and modulator are maintained at 3.3V and 1.7V and the DAC load is 50Ω. The added load of the filter
termination causes the signal to be attenuated by –10.8 dB.
A filter can be implemented in a similar manner to interface with the TRF3703-33. In this case it is much simpler
to balance the loads and common mode voltages due to the absence of R2. An added benefit is that there is no
loss in this network. With V1 = 5V and V2 = 0V the network can be designed such that R1 = 115Ω, R3 = 681Ω,
and R4 = 200Ω. This results in a filter impedance of R1 // R2=100Ω, and a DAC load of R1 // R3 // (R4/2) which
is equal to 50Ω. R4 is a differential resistor and does not affect the common mode level created by R1 and R3.
The common-mode voltage is set at 3.3 V for a full-scale current of 20mA.
For more information on how to interface the DAC3283 to an analog quadrature modulator please refer to the
application reports Passive Terminations for Current Output DACs (SLAA399) and Design of Differential Filters
for High-Speed Signal Chains (SLWA053).
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): DAC3283
43
DAC3283
SLAS693A – MARCH 2010 – REVISED APRIL 2010
www.ti.com
APPLICATION INFORMATION
DIRECT CONVERSION RADIO
Refer to Figure 56 for an example Direct Conversion Radio. The DAC3283 receives an interleaved complex I/Q
baseband input data stream and increases the sample rate through interpolation by a factor of 2 or 4. By
performing digital interpolation on the input data, undesired images of the original signal can be push out of the
band of interest and more easily suppressed with analog filters.
For a Zero IF (ZIF) frequency plan, complex mixing of the baseband signal is not required. Alternatively, for a
Complex IF frequency plan the input data can be pre-placed at an IF within the bandwidth limitations of the
interpolation filters. In addition, complex mixing is available using the coarse mixer block to up-convert the signal.
The output of both DAC channels is used to produce a Hilbert transform pair and can be expressed as:
AOUT(t) = A(t)cos(wct) – B(t)sin(wct) = m(t)
BOUT(t) = A(t)sin(wct) + B(t)cos(wct) = mh(t)
where m(t) and mh(t) connote a Hilbert transform pair and wc is the mixer frequency. The complex output is input
to an analog quadrature modulator (AQM) such as the Texas Instruments TRF3720 for a single side-band (SSB)
up conversion to RF. A passive (resistor only) interface to the AQM with an optional LC filter network is
recommended. The TRF3720 includes a VCO/PLL to generate the LO frequency. Upper single-sideband
upconversion is achieved at the output of the analog quadrature modulator, whose output is expressed as:
RF(t) = A(t)cos(wc + wLO)t – B(t)sin(wc + wLO)t
Flexibility is provided to the user by allowing for the selection of negative mixing frequency to produce a
lower-sideband upconversion. Note that the process of complex mixing translates the signal frequency from 0Hz
means that the analog quadrature modulator IQ imbalance produces a sideband that falls outside the signal of
interest. DC offset error in DAC and AQM signal path may produce LO feed-through at the RF output which may
fall in the band of interest. To suppress the LO feed-through, the DAC3283 provides a digital offset correction
capability for both DAC-A and DAC-B paths. In addition phase and gain imbalances in the DAC and AQM result
in a lower-sideband product. The DAC3283 offers gain and phase correction capabilities to minimize the
sideband product.
The complex IF architecture has several advantages over the real IF architecture:
• Uncalibrated side-band suppression ~ 35dBc compared to 0dBc for real IF architecture.
• Direct DAC to AQM interface – no amplifiers required
• DAC 2nd Nyquist zone image is offset fDAC compared with fDAC– 2 x IF for a real IF architecture, reducing the
need for filtering at the DAC output.
• Uncalibrated LO feed through for AQM is ~ 35dBc and calibration can reduce or completely remove the LO
feed through.
44
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): DAC3283
DAC3283
www.ti.com
SLAS693A – MARCH 2010 – REVISED APRIL 2010
APPLICATION INFORMATION (continued)
5V
Byte-Wide
Data
100
DATACLKP /N
100
Optional
Filter Network
FRAMEP/N
DAC-A
CMIX
100
I-FIR1
D0P/N
Q-FIR1
100
I-FIR0
D7P/N
Q-FIR0
DAC3283 DAC
FIFO & Demux
LVDS Data Interface
FPGA
DAC-B
RF OUT
DACCLKP/N
100
0
100
90
PLL/
DLL
Div
2/4/8
VCO
NDivider
VCTRL_IN
Loop
Filter
PFD
RDiv
/1
/4
Div
Clock Divider/
Distribution
CDCE62005
Clock Generator with VCO
PFD/CP
Loop
Filter
CPOUT
TRF3720
AQM with PLL/VCO
Div
10 MHz
OSC
Figure 56. System Diagram of Direct Conversion Radio
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): DAC3283
45
PACKAGE OPTION ADDENDUM
www.ti.com
9-Apr-2010
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
DAC3283IRGZR
ACTIVE
VQFN
RGZ
48
2500 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
DAC3283IRGZT
ACTIVE
VQFN
RGZ
48
250
CU NIPDAU
Level-3-260C-168 HR
Green (RoHS &
no Sb/Br)
Lead/Ball Finish
MSL Peak Temp (3)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 1
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DLP® Products
www.dlp.com
Communications and
Telecom
www.ti.com/communications
DSP
dsp.ti.com
Computers and
Peripherals
www.ti.com/computers
Clocks and Timers
www.ti.com/clocks
Consumer Electronics
www.ti.com/consumer-apps
Interface
interface.ti.com
Energy
www.ti.com/energy
Logic
logic.ti.com
Industrial
www.ti.com/industrial
Power Mgmt
power.ti.com
Medical
www.ti.com/medical
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
RFID
www.ti-rfid.com
Space, Avionics &
Defense
www.ti.com/space-avionics-defense
RF/IF and ZigBee® Solutions www.ti.com/lprf
Video and Imaging
www.ti.com/video
Wireless
www.ti.com/wireless-apps
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2010, Texas Instruments Incorporated