Specifications (at VR = VOP typical), 22°C Parameter Min Operating Voltage Breakdown Voltage Active Diameter Responsivity at 1300 nm Ceramic (D1)/TO-18 (D2) Fiber (D6)/FC (D4)/ST (D3)/SC (D5)1 Responsivity at 1550 nm Ceramic (D1)/TO-18 (D2) Fiber (D6)/FC (D4)/ST (D3)/SC (D5)1 Dark Current Spectral Noise Current (10 kHz, 1.0 Hz) Capacitance at VR = VOP (typ) C30618 Typ Max Min 10 1 25 5 80 350 Max 5 100 100 0.80 0.65 0.90 0.75 0.80 0.65 0.90 0.75 A/W 0.85 0.70 0.95 0.80 < 1.0 < 0.02 0.85 0.70 A/W 2.0 0.15 0.95 0.80 2.0 0.02 5.0 0.20 nA pA/√Hz 0.6 0.8 4.0 6.0 pF TO-18 (D2) Rise/Fall Time (10% to 90%) Bandwidth (-3 dB, RL = 50 Ω) 10 Units 1 25 (D1),(D6),(D3),(D5) Available Package Types C30617 Typ 0.8 1.0 4.0 6.0 0.07 0.5 0.5 1.0 3.5 0.75 D1, D2, D3, D4, D5, D6, V V µm ns GHz D1, D2, D3, D4, D21 - Maximum Ratings Maximum Forward Current Power Dissipation Storage Temperature 2 Operating Temperature 2 -60 -40 10 100 125 125 -60 -40 10 100 125 125 mA mW °C °C Note 1. Coupled from 62.5 Fm, 0.28 NA graded index multi-mode fiber using 1300 nm SLED source. Note 2. Maximum storage and operating temperature for connectorized and fibered devices is +85°C. C30618 C30617 C30637 C30616 Figure 3: Typical dark current vs. voltage Figure 4: Typical dark current vs. temperature at VOP = -5V. Standard Packages Figure 5: Package D1: Ceramic Submount Figure 6: Package D2: TO-18 low profile Figure 7: Package D3: ST receptacle module Figure 8: Package D4: FC detector module Figure 9: Package D5: SC receptacle module Figure 10: Package D6: Fibered detector module Standard Packages Figure 11: Termination D8: ST connector Figure 12: Termination D9: FC connector Figure 13: Termination D10: SC connector Figure 14: Package D21: TO-18 ball-lens package Ordering Guide C30 # # # L M M M - X X - N N Connector Connector Connector Fiber Termination ST: FC: SC: Fiber Type (Core/cladding/jacket in µm, NA) 04: 07: 62.5/125/900,0.29 9/125/900,0.10 Package Type ST: FC: SC: QC: CER: Receptacle Receptacle Receptacle Fibered -XX-NN Ceramic Lens Type E: B: Flat window, ceramic TO-18, ceramic submount submount Connector/fibered/ball Ball lenslens, TO-18, stand alone or with fiber / connector Chip Type 616, 637, 617, 618 Note: Specific package types available for each photodiode are listed in the table of specifications. For more information e-mail us at [email protected] or visit our web site at www.perkinelmer.com/opto All values are nominal; specifications subject to change without notice. ©2000 PerkinElmer, Inc. All rights reserved. 0400 is a registered trademark of PerkinElmer, Inc. PerkinElmer Optoelectronics 22001 Dumberry Road Vaudreuil (QC) Canada J7V 8P7 Phone: (450) 424-3300 Fax: (450) 424-3411