AKM AK4223VQ

[AK4223]
AK4223
6:2 Audio Switch and 6:2 Video Switch
GENERAL DESCRIPTION
The AK4223 is an AV switch with 6:2 audio and 6:2 video switches. High performances with low power
consumption are achieved by CMOS process. Integrated differential input circuits in audio and video
blocks can separate the external ground noise. In audio block, a differential input circuit, audio LPF and
0dB/-6dB gain amplifier are integrated eliminating the needs for external LPF for audio outputs. In video
block, an input clamp circuit, 6dB amplifier and video driver are integrated, and they also eliminate the
need for external circuits. The AK4223 is offered in a space saving small 48-pin LQFP package, ideal for
car navigation applications.
FEATURES
1. Audio Section
• Selector with 6 inputs and 2 outputs
• Differential Input Circuit for Ground Noise Canceling
• LPF Circuit for Audio signals
• Output Gain Control: 0dB ∼ - 6dB, -1dB Step
• S/(N+D): 90dB (@0dBV)
• Dynamic Range: 94dB
• Channel-Independent Mute Function
2. Video Section
• Selector with 6 inputs and 2 outputs
• Six Composite Signal Inputs
• On-Chip Sync-tip Clamp Circuit
• Video Drivers for Composite Signal Output (+6dB/+3dB/0dB/-3dB)
• Output Gain Control: -1dB ∼ +1dB, 0.1dB Step
• LPF Circuit for Video signals (Bandwidth: 6MHz)
• S/N: 65dB
• Channel-Independent Mute Function
3. Control Section
• Serial µP I/F (I2C)
4. Power Supply: 7.5V ∼ 9.5V
5. Ta = -40 ∼ 85 °C
6. Package: 48pin LQFP
MS1251-E-00
1
2010/10
[AK4223]
Audio Block
SW1
LIN1
VCOM
LPF
0dB~
-6dB
LOUT1
LPF
0dB~
-6dB
ROUT1
LPF
0dB~
-6dB
LOUT2
LPF
0dB~
-6dB
ROUT2
GND1
RIN1
SW2
Input #1
LIN2
GND2
RIN2
(same circuit)
LIN3
GND3
RIN3
(same circuit)
LIN4
GND4
RIN4
(same circuit)
LIN5
GND5
RIN5
(same circuit)
LIN6
GND6
RIN6
(same circuit)
Input #2
Input #3
Bias
Input #4
VCOM
Input #5
Regulator1
Input #6
VSS1
AVDD
RVDD
VVDD
VIN1
SW3
Regulator2
REGV
VGND1
VSS2
VIN2
VGND2
VR1
VIN3
VGND3
SW4
GCA
LPF
(same circuit)
VIN5
VGND5
(same circuit)
VIN6
VGND6
(same circuit)
VOUT1
−3/0/+3/+6dB
(same circuit)
VIN4
VGND4
SCL
SDA
LPF
(same circuit)
GCA
VOUT2
VR2
Bias
Video Block
Register Control
RSTN
Figure 1. AK4223 Block Diagram
MS1251-E-00
2
2010/10
[AK4223]
■ Ordering Guide
AK4223VQ
AKD4223
-40 ∼ +85°C
48pin LQFP (0.5mm pitch)
Evaluation Board for AK4223
MS1251-E-00
LIN3
GND3
RIN3
LIN4
GND4
RIN4
LIN5
GND5
RIN5
LIN6
GND6
RIN6
36
35
34
33
32
31
30
29
28
27
26
25
■ Pin Layout
VSS1
37
24
LOUT1
RIN2
38
23
ROUT1
GND2
39
22
LOUT2
LIN2
40
21
ROUT2
RIN1
41
20
RVDD
GND1
42
19
AVDD
LIN1
43
18
VVDD
17
RSTN
AK4223
Top Vie w
3
10
11
12
VGND1
VIN1
VR2
9
VOUT2
VIN2
13
8
48
VGND2
VGND6
7
VOUT1
VIN3
14
6
47
VGND3
VSS2
5
VR1
VIN4
15
4
46
VGND4
SCL
3
REGV
VIN5
16
2
45
VGND5
SDA
1
44
VIN6
VCOM
2010/10
[AK4223]
PIN/FUNCTION
No.
1
2
3
4
5
6
7
8
9
10
11
12
Pin Name
VIN6
VGND5
VIN5
VGND4
VIN4
VGND3
VIN3
VGND2
VIN2
VGND1
VIN1
I/O
I
I
I
I
I
I
I
I
I
I
I
VR2
O
13
14
15
VOUT2
VOUT1
O
O
VR1
O
16
REGV
O
17
RSTN
I
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
VVDD
AVDD
RVDD
ROUT2
LOUT2
ROUT1
LOUT1
RIN6
GND6
LIN6
RIN5
GND5
LIN5
RIN4
GND4
LIN4
RIN3
GND3
LIN3
VSS1
RIN2
GND2
LIN2
O
O
O
O
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
MS1251-E-00
Function
Video Signal Input Pin 6.
Video GND Input Pin 5.
Video Signal Input Pin 5.
Video GND Input Pin 4.
Video Signal Input Pin 4.
Video GND Input Pin 3.
Video Signal Input Pin 3.
Video GND Input Pin 2.
Video Signal Input Pin 2.
Video GND Input Pin 1.
Video Signal Input Pin 1.
Video Signal Clamp Reference Pin 2.
Normally connected to VSS2 with a 0.1μF capacitor.
Video Signal Output Pin 2.
Video Signal Output Pin 1.
Video Signal Clamp Reference Pin 1.
Normally connected to VSS2 with a 0.1μF capacitor.
Regulator Output Pin for the power supply of Video Core Circuit. 5.0V (typ)
For stability of the regulator, this pin must connect to VSS2 with a 10μF
capacitor.
Reset Mode Pin
“L”: Reset mode (All registers are initialized to their default values.)
“H”: Normal operation
Power Supply Pin: 7.5V~9.5V
Power Supply Pin: 7.5V~9.5V
Power Supply Pin: 7.5V~9.5V
Audio Signal Output Pin ROUT 2.
Audio Signal Output Pin LOUT 2.
Audio Signal Output Pin ROUT 1.
Audio Signal Output Pin LOUT 1.
Audio Signal Input Pin RIN 6.
Audio GND Input Pin GND 6.
Audio Signal Input Pin LIN 6.
Audio Signal Input Pin RIN 5.
Audio GND Input Pin GND 5.
Audio Signal Input Pin LIN 5.
Audio Signal Input Pin RIN 4.
Audio GND Input Pin GND 4.
Audio Signal Input Pin LIN 4.
Audio Signal Input Pin RIN 3.
Audio GND Input Pin GND 3.
Audio Signal Input Pin LIN 3.
Audio Ground Pin
Audio Signal Input Pin RIN 2.
Audio GND Input Pin GND 2.
Audio Signal Input Pin LIN 2.
4
2010/10
[AK4223]
PIN/FUNCTION (Continued)
No.
41
42
43
44
Pin Name
RIN1
GND1
LIN1
I/O
I
I
I
VCOM
O
45
46
47
48
SDA
SCL
VSS2
VGND6
I/O
I
I
Function
Audio Signal Input Pin RIN 1.
Audio GND Input Pin GND 1.
Audio Signal Input Pin LIN 1.
Audio VCOM Voltage Pin.
Normally connected to VSS1 with a 1μF electrolytic capacitor.
Control Data Pin.
Control Data Clock Pin.
Video Ground Pin.
Video GND Input Pin 6.
■ Handling of Unused Pin
The unused I/O pins should be processed appropriately as below.
Classification
Audio Inputs
Video Input
Audio, Video Outputs
MS1251-E-00
Pin Name
LIN1-6, RIN1-6, GND1-6
VIN1-6, VGND1-6
LOUT1-2, ROUT1-2, VOUT1-2
Setting
These pins must be open.
These pins must be connected to VSS2.
These pins must be open.
5
2010/10
[AK4223]
ABSOLUTE MAXIMUM RATINGS
(VSS1=VSS2 =0V; Note 1)
Parameter
Power Supply
Symbol
AVDD
VVDD
RVDD
IIN
VINA
VINV
VIND
Ta
Tstg
min
max
Units
-0.3
+14.0
V
±10
AVDD+0.3
5.5
5.5
85
150
mA
V
V
V
°C
°C
Input Current (any pins except for supplies)
Audio Input Voltage
-0.3
Video Input Voltage
-0.3
Digital Input Voltage
-0.3
Ambient Operating Temperature
-40
Storage Temperature
-65
Note 1. All voltages with respect to ground.
Note 2. VSS1 and VSS2 must be connected to the same analog ground plane.
Note 3. AVDD and RVDD must be the same voltage.
WARNING: Operation at or beyond these limits may result in permanent damage to the device.
Normal operation is not guaranteed at these extremes.
RECOMMENDED OPERATING CONDITIONS
(VSS1=VSS2 = 0V)
Parameter
Power Supply
Symbol
AVDD
VVDD
RVDD
Note 3. AVDD and RVDD must be the same voltage.
min
typ
max
Units
7.5
9.0
9.5
V
*AKM assumes no responsibility for the usage beyond the conditions in this datasheet.
ELECTRICAL CHARACTERISTICS
(Ta=25°C; AVDD= RVDD= VVDD= 9.0V; VSS1= VSS2 = 0V)
Power Supplies
Parameter
min
typ
max
Power Supply (AVDD+RVDD+VVDD)
Normal Operation (Note 4), (RSTN pin = “H”)
33
50
Power-Down Mode (Note 5), (RSTN pin = “L”)
2.1
3.1
Note 4. No input, No load.
Note 5. This is the value without analog inputs when all digital input pins are fixed to VSS1 or VSS2.
MS1251-E-00
6
Units
mA
μA
2010/10
[AK4223]
ANALOG CHARACTERISTICS (Audio)
(Ta=25°C; AVDD= RVDD= VVDD= 9.0V; VSS1=VSS2= 0V; Signal Frequency=1kHz, Measurement Frequency=
20Hz∼20kHz, unless otherwise specified)
Parameter
Conditions
min
typ
max
Units
S/(N+D) (Note 6)
Input=0dBV
82
90
dB
DR (0dBV reference) (Note 6) Input=-60dBV, A-weighted
88
94
dB
S/N (0dBV reference) (Note 6) A-weighted
88
94
dB
Input Impedance
70
100
kΩ
Input Voltage (Note 7)
2
Vrms
Gain
0dB
-0.4
0
+0.4
dB
-6dB
-6.4
-6.0
-5.6
dB
AGCA step
(Note 6)
1.0
dB
Interchannel Isolation (Note 8)
100
dB
LPF Frequency Response
Response at 24kHz
-2
-0.5
dB
Input=1Vrms, 0dB at 1kHz
Response at 96kHz
-24
dB
Interchannel Gain Mismatch
0.2
dB
Gain Drift
20
ppm/°C
300
Load Resistance (Note 9)
R1
(Figure 2)
Ω
5
R1+R2 (Figure 2)
kΩ
1.5
nF
Load Capacitance
C1
(Figure 2)
30
pF
C2
(Figure 2)
Power Supply Rejection
(Note 10)
74
dB
CMRR
f=1kHz, 1Vp-p input
35
45
dB
Note 6. This is a value when AGCA=0dB.
Note 7. The Input Voltage meets S/(N+D)>82dB.
Note 8. Between all channels of LIN1-6 and RIN1-6.
Note 9. The output resistance of audio output (LOUT1-2 and ROUT1-2) are less than l0Ω (typ).
Note 10. Applied to AVDD, RVDD and VVDD with a sine wave (1kHz, 50mVpp).
R1
300Ω
C3
10uF
LOU T/ROUT
C21
C22
C2=C21+C22= 30pF(max)
C1
R2
4.7kΩ
C1= 1.5nF(max)
Figure 2. Load Resistance R1, R2 and Load Capacitance C1, C2
MS1251-E-00
7
2010/10
[AK4223]
ANALOG CHARACTERISTICS (Video)
(Ta = 25°C; AVDD= RVDD= VVDD= 9.0V; VSS1= VSS2 = 0V; VGAIN= +6dB, VGCA=0dB; VR1/2 bit=“0”; unless
otherwise specified.)
Parameter
Conditions
min
typ
max
Units
Sync tip clamp level
VGAIN=+3dB, +6dB
200
mV
(Note 11)
VGAIN=-3dB, 0dB
500
mV
Gain
VGCA=+1dB
6dB
7
dB
Input=0.3Vp-p, 100kHz
3dB
4
dB
0dB
1
dB
-3dB
-2
dB
VGCA=0dB
6dB
5.6
6
6.4
dB
3dB
2.6
3
3.4
dB
0dB
-0.4
0
0.4
dB
-3dB
-3.4
-3
-2.6
dB
6dB
5
dB
VGCA=-1dB
3dB
2
dB
0dB
-1
dB
-3dB
-4
dB
VGCA step
0.1
dB
Frequency Response
Response at 6MHz
-1.0
+1.0
dB
Input=0.3Vpp, Sin Wave Response at 27MHz
-35
dB
(0dB at 100kHz)
Group Delay Distortion
|GD3MHz – GD6MHz|
10
40
ns
Input Impedance
300
kΩ
Input Signal
1.5
Vpp
Inter channel Isolation
f=4.43MHz, 1Vpp input
52
dB
S/N
Reference Level = 0.7Vp-p,
65
dB
BW= 100kHz to 6MHz.
Differential Gain
0.7Vpp 5steps modulated staircase.
+0.4
%
Chrominance & burst are 280mVpp, 4.43MHz.
Differential Phase
0.7Vpp 5steps modulated staircase.
+1
Degree
Chrominance & burst are 280mVpp, 4.43MHz.
Load Resistance
VR1/2 bit = “0”, R1+R2 (Figure 4)
140
150
160
Ω
VR1/2 bit = “1”, R1 (Figure 5)
100
kΩ
Load Capacitance
VR1/2 bit = “0”, (Figure 4)
C1
1.5
nF
C2
15
pF
VR1/2 bit = “1”, (Figure 5)
C1+C2
15
pF
CMRR
f=20kHz, 1Vp-p input
34
55
dB
Note 11. At the measurement point A in Figure 3. Idling DC output level is 200mV(max) when VGAIN=+6dB or +3db,
and 500mV(max) when VGAIN=0dB or -3dB.
Measurment point A
VOUT
Pedestal Volltage
75Ω
0V
a
a: 100mV(max): VGAIN=+3dB, +6dB
75Ω
Figure 3. Measurement Point
MS1251-E-00
8
2010/10
[AK4223]
R1
75 Ω
VOUT
R2
75 Ω
C1
C2
max: 15pF
(C2)
max:1.5nF
(C1)
Figure 4. Load Resistance R1+R2 and Load Capacitance C1/C2 (VR1/2 bit = “0”)
R1
100kΩ (min)
C
VOUT
C1
C2
C1+C2=15pF (max)
Figure 5. Load Resistance R1+R2 and Load Capacitance C1/C2 (VR1/2 bit = “1”)
DC CHARACTERISTICS
(Ta=-40~85°C; AVDD= RVDD= VVDD= 7.5∼9.5V)
Parameter
Symbol
High-Level Input Voltage (RSTN,SCL,SDA,CAD pins)
VIH
Low-Level Input Voltage (RSTN,SCL,SDA,CAD pins)
VIL
Low-Level Output Voltage (SDA pin: Iout=3mA)
Input Leakage Current
VOL
Iin
min
2.7
-
typ
-
max
5.5
0.8
Units
V
V
-
-
0.4
±10
V
μA
SWITCHING CHARACTERISTICS
(Ta= 25°C; AVDD =RVDD= VVDD= 9.0V)
Control Interface Timing (I2C Bus)
SCL Clock Frequency
fSCL
Bus Free Time Between Transmissions
tBUF
1.3
Start Condition Hold Time (prior to first clock pulse)
tHD:STA
0.6
Clock Low Time
tLOW
1.3
Clock High Time
tHIGH
0.6
Setup Time for Repeated Start Condition
tSU:STA
0.6
SDA Hold Time from SCL Falling
(Note 13)
tHD:DAT
0
SDA Setup Time from SCL Rising
tSU:DAT
0.1
Rise Time of Both SDA and SCL Lines
tR
Fall Time of Both SDA and SCL Lines
tF
Setup Time for Stop Condition
tSU:STO
0.6
Pulse Width of Spike Noise Suppressed by Input Filter
tSP
0
Capacitive load on bus
Cb
Power-down & Reset Timing
RSTN Reject Pulse Width
tRPD
RSTN Pulse Width
(Note 14)
tPD
150
2
Note 12. I C-bus is a trademark of NXP B.V.
Note 13. Data must be held long enough to bridge the 300ns-transition time of SCL.
Note 14. The AK4223 can be reset by setting the RSTN pin = “L” when powered up.
MS1251-E-00
9
400
0.3
0.3
50
400
kHz
μs
μs
μs
μs
μs
μs
μs
μs
μs
μs
ns
pF
15
ns
ns
2010/10
[AK4223]
■ Timing Diagram
VIH
SDA
VIL
tBUF
tLOW
tR
tHIGH
tF
tSP
VIH
SCL
VIL
tHD:STA
Stop
tHD:DAT
tSU:DAT
tSU:STA
tSU:STO
Start
Stop
Start
Figure 6. I2C Bus mode Timing
tPD
RSTN
VIL
Figure 7. Reset Mode Timing
MS1251-E-00
10
2010/10
[AK4223]
OPERATION OVERVIEW
■ Power Up/Down
The AK4223 can be reset by bringing the RSTN pin = “L” upon power-up. In reset mode, internal resisters are initialized
and the audio and video circuits are in power-down state outputting Hi-Z signals. The RSTN pin must be “L” to execute
this reset when power up the AK4223.
■ Audio and Video Signal Inputs
1. Audio Signal Input
The ground noise is cancelled by the differential input with the same ground for L and R channels. The output of LIN and
RIN are the same phase. LIN1-6, RIN1-6 and GND1-6 pins must be AC coupled with a 0.47uF capacitor.
(Cable)
LIN1-6
RIN1-6
0.47μF
GND1-6
(Cable)
0.47μF
Figure 8. Audio Input Circuit (Differential)
(Cable)
LIN1-6
RIN1-6
0.47μF
GND1-6
0.47μF
Figure 9. Audio Input Circuit (Single-ended)
2. Video Signal Input
Sync-tip output level is fixed by the internal clamp circuit. VIN1-6 pins must be input via a 0.1uF capacitor for AC
coupling.
VIN1-6
(Cable)
0.1μF
(Cable)
0.1μF
VGND1-6
Figure 10. Video Input Circuit (Differential)
VIN1-6
(Cable)
0.1μF
VGND1-6
0.1μF
Figure 11. Video Input Circuit (Single-ended)
MS1251-E-00
11
2010/10
[AK4223]
■ Input Selector
The AK4223 has 6:2 input selectors for audio input, and 6:2 input selectors for video input. The audio input selectors are
set by ASEL12-10bits and ASEL22-20 bits, and the video input selectors are set by VSEL12-10bits and VSEL22-20 bits.
ASEL12 bit
0
0
0
0
1
1
1
1
ASEL11 bit
ASEL10 bit
Input Selector
0
0
Off (Note 15)
0
1
LIN1 / RIN1
1
0
LIN2 / RIN2
1
1
LIN3 / RIN3
0
0
LIN4 / RIN4
0
1
LIN5 / RIN5
1
0
LIN6 / RIN6
1
1
(Reserved)
Table 1. Audio Input Selector 1 (LOUT1/ROUT1)
ASEL22 bit
0
0
0
0
1
1
1
1
ASEL21 bit
ASEL20 bit
Input Selector
0
0
Off (Note 15)
0
1
LIN1 / RIN1
1
0
LIN2 / RIN2
1
1
LIN3 / RIN3
0
0
LIN4 / RIN4
0
1
LIN5 / RIN5
1
0
LIN6 / RIN6
1
1
(Reserved)
Table 2. Audio Input Selector 2 (LOUT2/ROUT2)
(default)
(default)
Note 15. The audio outputs become 3.9V(typ., Gain=0dB) when input selectors are OFF.
VSEL12 bit
0
0
0
0
1
1
1
1
VSEL11 bit
VSEL10 bit
Input Selector
0
0
Off (Note 16)
0
1
VIN1
1
0
VIN2
1
1
VIN3
0
0
VIN4
0
1
VIN5
1
0
VIN6
1
1
(Reserved)
Table 3. Video Input Selector 1 (VOUT1)
VSEL22 bit
0
0
0
0
1
1
1
1
VSEL21 bit
VSEL20 bit
Input Selector
0
0
Off (Note 16)
0
1
VIN1
1
0
VIN2
1
1
VIN3
0
0
VIN4
0
1
VIN5
1
0
VIN6
1
1
(Reserved)
Table 4. Video Input Selector 2 (VOUT2)
(default)
(default)
Note 16. The video outputs become sync tip level when input selectors are OFF.
MS1251-E-00
12
2010/10
[AK4223]
■ Audio Output Level Setting
AGCA12-10 bits control the audio output level of the L/ROUT1 pin, and AGCA22-20 bits controls the audio output
level of the L/ROUT2 pin. (Table 5, Table 6)
AGCA12 bit
0
0
0
0
1
1
1
1
AGCA11 bit
0
0
1
1
0
0
1
1
AGCA10 bit
0
1
0
1
0
1
0
1
L/ROUT1 GAIN [dB]
0 (default)
-1
-2
-3
-4
-5
-6
Reserved
Output DC Level[V typ]
3.9
3.7
3.5
3.4
3.2
3.1
3.0
-
STEP
1dB
Table 5. L/ROUT1 Output Level Setting
AGCA22 bit
0
0
0
0
1
1
1
1
AGCA21 bit
0
0
1
1
0
0
1
1
AGCA20 bit
0
1
0
1
0
1
0
1
L/ROUT2 GAIN [dB]
0 (default)
-1
-2
-3
-4
-5
-6
Reserved
Output DC Level[V typ]
3.9
3.7
3.5
3.4
3.2
3.1
3.0
-
STEP
1dB
Table 6. L/ROUT2 Output Level Setting
■ Audio Output Mute Select
The AK4223 has a channel independent mute function for audio outputs. AMUTE1/2 bits control L/ROUT1 and
L/ROUT2 outputs mute. (Table 7, Table 8)
AMUTE1 bit
L/ROUT1 Output
0
Normal Output
(default)
1
Mute
Table 7. L/ROUT1 Output Mute Control
AMUTE2 bit
L/ROUT2 Output
0
Normal Output
(default)
1
Mute
Table 8. L/ROUT2 Output Mute Control
MS1251-E-00
13
2010/10
[AK4223]
■ Video Output Level Setting
VGAIN11-10 bits control the video output level of the VOUT1 pin, and VGAIN21-20 bits control the video output level
of the VOUT2 pin. (Table 9, Table 10)
VGAIN11 bit
0
0
1
1
VGAIN21 bit
0
0
1
1
VGAIN10 bit
0
1
0
1
VGAIN20 bit
0
1
0
1
VOUT1 output Level VOUT1 Sync Tip Level (max)
+6dB
200mV
(default)
0dB
500mV
+3dB
200mV
-3dB
500mV
Table 9.VOUT1 Output Level Setting
VOUT2 output Level VOUT2 Sync Tip Level (max)
+6dB
200mV
0dB
500mV
+3dB
200mV
-3dB
500mV
Table 10.VOUT2 Output Level Setting
(default)
VGCA14-10 bits finely tune the video output levels of VOUT1, and VGCA24-20 bits tune VOUT2. (Table 11, Table 12)
VGCA14-10 bit
VOUT1 GAIN [dB]
STEP
00000
−1.0
00001
−0.9
00010
−0.8
:
:
01010
0 (default)
0.1dB
:
:
10010
+0.8
10011
+0.9
10100
+1.0
others
Reserved
Table 11. Video Output Level (VOUT1) Fine Tuning Setting
VGCA24-20 bit
VOUT2 GAIN [dB]
STEP
00000
−1.0
00001
−0.9
00010
−0.8
:
:
01010
0 (default)
0.1dB
:
:
10010
+0.8
10011
+0.9
10100
+1.0
others
Reserved
Table 12. Video Output Level (VOUT2) Fine Tuning Setting
MS1251-E-00
14
2010/10
[AK4223]
■ Video Output Driver
VR1 and VR2 bits control the video output driver of the VOUT1 and VOUT2 pins respectively. VR1 and VR2 bits should
be set to “0” when driving 150Ω resistance.
VR1 bit
VOUT1
0
150Ω Drive
(default)
1
min. 100kΩ Drive
Table 13. VOUT1 Output Driver Setting
VR2 bit
VOUT2
0
150Ω Drive
(default)
1
min. 100kΩ Drive
Table 14. VOUT2 Output Driver Setting
■ Video Output Mute Setting
The AK4223 has a channel independent mute function of the video output. VMUTE1 and VMUTE2 bits mute (Sync tip
clamp level) VOUT1 and VOUT2 outputs respectively. (Table 15, Table 16)
VMUTE1 bit
VOUT1 Output
0
Normal Output
(default)
1
Mute
Table 15. VOUT1 Output Mute Control
VMUTE2 bit
VOUT2 Output
0
Normal Output
(default)
1
Mute
Table 16. VOUT2 Output Mute Control
MS1251-E-00
15
2010/10
[AK4223]
■ System Reset
The RSTN pin must be set to “L” when power up the AK4223. The AK4223 powers up in reset state. The REGV pin
starts outputting (typ. 5.0V) when power is supplied to the device. This reset is released by setting the RSTN pin to “H”.
Figure 12 shows the reset sequence.
Power Supply
(VVDD, AVDD, RVDD)
(1)
REGV pin Output
VSS
REGV=5.0V(TYP)
(2)
RSTN Pin
Audio⋅Video Circuit
(3)
Power down
Audio Output: Hi-Z
Power Up
Notes:
(1) Time that the REGV output reaches 95% of the maximum value. (typ. 800μs, max. 5ms)
(2) Reset Time (min. 150ns)
(3) Time to be in a normal operation after reset release. (Video Output: typ. 100ms, Audio Output: typ. 170ms)
*The required time to be in a normal operation of audio outputs is proportional to the capacity of an external capacitor
at the VCOM pin. This typical value 170ms is for when the external capacitor is 1.0μF.
Figure 12 System Reset Diagram
MS1251-E-00
16
2010/10
[AK4223]
■ Control Interface
The AK4223 supports the fast-mode I2C-bus system (max: 400kHz).
2-1. WRITE Operation
Figure 13 shows the data transfer sequence for the I2C-bus mode. All commands are preceded by a START condition. A
HIGH to LOW transition on the SDA line while SCL is HIGH indicates a START condition (Figure 19). After the
START condition, a slave address is sent. This address is 7 bits long followed by the eighth bit that is a data direction bit
(R/W). The most significant seven bits of the slave address are fixed as “0010000”. If the slave address matches that of the
AK4223, the AK4223 generates an acknowledge and the operation is executed. The master must generate the
acknowledge-related clock pulse and release the SDA line (HIGH) during the acknowledge clock pulse (Figure 20). A
R/W bit value of “1” indicates that the read operation is to be executed. A “0” indicates that the write operation is to be
executed.
The second byte consists of the control register address of the AK4223. The format is MSB first, and those most
significant 3-bits are fixed to zeros (Figure 15). The data after the second byte contains control data. The format is MSB
first, 8bits (Figure 16). The AK4223 generates an acknowledge after each byte has been received. A data transfer is
always terminated by a STOP condition generated by the master. A LOW to HIGH transition on the SDA line while SCL
is HIGH defines a STOP condition (Figure 19).
The AK4223 can perform more than one byte write operation per sequence. After receipt of the third byte the AK4223
generates an acknowledge and awaits the next data. The master can transmit more than one byte instead of terminating the
write cycle after the first data byte is transferred. After receiving each data packet the internal 8-bit address counter is
incremented by one, and the next data is automatically taken into the next address. If the address exceeds 06H prior to
generating the stop condition, the address counter will “roll over” to 00H and the previous data will be overwritten.
The data on the SDA line must remain stable during the HIGH period of the clock. The HIGH or LOW state of the data
line can only change when the clock signal on the SCL line is LOW (Figure 21) except for the START and STOP
conditions.
S
T
A
R
T
SDA
S
T
O
P
R/W = "0"
Slave
S Address
Sub
Address(n)
Data(n)
A
C
K
Data(n+1)
A
C
K
A
C
K
Data(n+x)
A
C
K
P
A
C
K
A
C
K
Figure 13. Data Transfer Sequence at the I2C-Bus Mode
0
0
1
0
0
0
0
R/W
A2
A1
A0
D2
D1
D0
Figure 14. The First Byte
0
0
0
0
0
Figure 15. The Second Byte
D7
D6
D5
D4
D3
Figure 16. Byte Structure after the second byte
MS1251-E-00
17
2010/10
[AK4223]
2-2. READ Operations
Set the R/W bit = “1” for the READ operation of the AK4223. After transmission of data, the master can read the next
address’s data by generating an acknowledge instead of terminating the write cycle after the receipt of the first data word.
After receiving each data packet the internal 5-bit address counter is incremented by one, and the next data is
automatically taken into the next address. If the address exceeds 06H prior to generating a stop condition, the address
counter will “roll over” to 00H and the previous data will be overwritten.
The AK4223 supports two basic read operations: CURRENT ADDRESS READ and RANDOM ADDRESS READ.
2-2-1. CURRENT ADDRESS READ
The AK4223 contains an internal address counter that maintains the address of the last word accessed, incremented by
one. Therefore, if the last access (either a read or write) were to address “n”, the next CURRENT READ operation would
access data from the address “n+1”. After receipt of the slave address with R/W bit set to “1”, the AK4223 generates an
acknowledge, transmits 1-byte of data to the address set by the internal address counter and increments the internal
address counter by 1. If the master does not generate an acknowledge to the data but instead generates a stop condition,
the AK4223 ceases transmission.
S
T
A
R
T
SDA
S
T
O
P
R/W = "1"
Slave
S Address
Data(n+1)
Data(n)
A
C
K
A
C
K
Data(n+2)
A
C
K
Data(n+x)
A
C
K
A
C
K
P
A
C
K
Figure 17. CURRENT ADDRESS READ
2-2-2. RANDOM ADDRESS READ
The random read operation allows the master to access any memory location at random. Prior to issuing the slave address
with the R/W bit set to “1”, the master must first perform a “dummy” write operation. The master issues a start request, a
slave address (R/W bit = “0”) and then the register address to read. After the register address is acknowledged, the master
immediately reissues the start request and the slave address with the R/W bit set to “1”. The AK4223 then generates an
acknowledge, 1 byte of data and increments the internal address counter by 1. If the master does not generate an
acknowledge to the data but instead generates a stop condition, the AK4223 ceases transmission.
S
T
A
R
T
SDA
S
T
A
R
T
R/W = "0"
Slave
S Address
Slave
S Address
Sub
Address(n)
A
C
K
A
C
K
S
T
O
P
R/W = "1"
Data(n)
A
C
K
Data(n+1)
A
C
K
Data(n+x)
A
C
K
A
C
K
P
A
C
K
Figure 18. RANDOM ADDRESS READ
MS1251-E-00
18
2010/10
[AK4223]
SDA
SCL
S
P
start condition
stop condition
Figure 19. START and STOP Conditions
DATA
OUTPUT BY
TRANSMITTER
not acknowledge
DATA
OUTPUT BY
RECEIVER
acknowledge
SCL FROM
MASTER
2
1
8
9
S
clock pulse for
acknowledgement
START
CONDITION
Figure 20. Acknowledge on the I2C-Bus
SDA
SCL
data line
stable;
data valid
change
of data
allowed
Figure 21. Bit Transfer on the I2C-Bus
MS1251-E-00
19
2010/10
[AK4223]
■ Register Map
Addr
00H
01H
02H
03H
04H
05H
06H
Register Name
Control
Input Selector Control1
Input Selector Control2
Output Level Control1
Output Level Control2
Output Level Control3
Output Level Control4
D7
0
0
0
0
0
0
0
D6
0
ASEL22
VSEL22
AGCA22
VR2
0
0
D5
VMUTE2
ASEL21
VSEL21
AGCA21
VR1
0
0
D4
VMUTE1
ASEL20
VSEL20
AGCA20
0
VGCA14
VGCA24
D3
0
0
0
0
VGAIN21
VGCA13
VGCA23
D2
0
ASEL12
VSEL12
AGCA12
VGAIN20
VGCA12
VGCA22
D1
AMUTE2
ASEL11
VSEL11
AGCA11
VGAIN11
VGCA11
VGCA21
D0
AMUTE1
ASEL10
VSEL10
AGCA10
VGAIN10
VGCA10
VGCA20
Note: Do not write any data to the register over 07H.
When the PDN pin changes to “L”, the registers are initialized to their default values.
The bits defined as 0 must contain a “0” value.
MS1251-E-00
20
2010/10
[AK4223]
■ Register Definitions
Addr
00H
Register Name
Control
Default
D7
0
0
D6
0
0
D5
VMUTE2
0
D4
VMUTE1
0
D3
0
0
D2
0
0
D1
AMUTE2
0
D0
AMUTE1
0
AMUTE2-1: Audio Output Mute Control (Table 7, Table 8)
0: Normal Operation (default)
1: Mute
VMUTE2-1: Video Output Mute Control (Table 15, Table 16)
0: Normal Operation (default)
1: Mute
Addr
01H
Register Name
Input Selector Control1
Default
D7
0
0
D6
ASEL22
0
D5
ASEL21
0
D4
ASEL20
0
D3
0
0
D2
ASEL12
0
D1
ASEL11
0
D0
ASEL10
0
D2
VSEL12
0
D1
VSEL11
0
D0
VSEL10
0
D2
AGCA12
0
D1
AGCA11
0
D0
AGCA10
0
ASEL12-10: Audio Input Selector 1 Control (Table 1)
The LOUT1/ROUT2 pin outputs 3.9V (typ., Gain=0dB) at the default setting “000”.
ASEL22-20: Audio Input Selector 2 Control (Table 2)
The LOUT2/ROUT2 pin outputs 3.9V (typ., Gain=0dB) at the default setting “000”.
Addr
02H
Register Name
Input Selector Control2
Default
D7
0
0
D6
VSEL22
0
D5
VSEL21
0
D4
VSEL20
0
D3
0
0
VSEL12-10: Video Input Selector 1 Control (Table 3)
The video output is sync tip clamp level at the default setting “000”.
VSEL22-20: Video Input Selector 2 Control (Table 4)
The video output is sync tip clamp level at the default setting “000”.
Addr
03H
Register Name
Output Level Control1
Default
D7
0
0
D6
AGCA22
0
D5
AGCA21
0
D4
AGCA20
0
D3
0
0
AGCA11-10: Audio Output L/ROUT1 Level Control (Table 5)
000: 0dB (default)
001: -1dB
010: -2dB
…
110: -6dB
111: Reserved
AGCA21-20: Audio Output L/ROUT2 Level Control (Table 6)
000: 0dB (default)
001: -1dB
010: -2dB
…
110: -6dB
111: Reserved
MS1251-E-00
21
2010/10
[AK4223]
Addr
04H
Register Name
Output Level Control2
Default
D7
0
0
D6
VR2
0
D5
VR1
0
D4
0
0
D3
VGAIN21
0
D2
VGAIN20
0
D1
VGAIN11
0
D0
VGAIN10
0
VGAIN11-10: Video Output1 Level Control (Table 9)
00: +6dB (default)
01: 0dB
10: +3dB
11: -3dB
VGAIN21-20: Video Output2 Level Control (Table 10)
00: +6dB (default)
01: 0dB
10: +3dB
11: -3dB
VR1: Video Output1 Load Resistance
0: Drive 150Ω (default)
1: Drive 100kΩ (min)
VR2: Video Output2 Load Resistance
0: Drive 150Ω (default)
1: Drive 100kΩ (min)
Addr
05H
Register Name
Output Level Control3
Default
D7
0
0
D6
0
0
D5
0
0
D4
VGCA14
0
D3
VGCA13
1
D2
VGCA12
0
D1
VGCA11
1
D0
VGCA10
0
VGCA14-10: Video Output1 Level Control (Table 11)
The video output is +6dB (when VGAIN11-10 bits = “00”), 0dB (when VGAIN11-10 bits = “01”), +3dB
(when VGAIN11-10 bits= “10”) and -3dB (when VGAIN11-10 bits = “11”) at the default setting “01010”.
Addr
06H
Register Name
Output Level Control4
Default
D7
0
0
D6
0
0
D5
0
0
D4
VGCA24
0
D3
VGCA23
1
D2
VGCA22
0
D1
VGCA21
1
D0
VGCA20
0
VGCA24-20: Video Output2 Level Control (Table 12)
The video output is +6dB (when VGAIN21-20 bits = “00”), 0dB (when VGAIN21-20 bits = “01”), +3dB
(when VGAIN21-20 bits= “10”) and -3dB (when VGAIN21-20 bits = “11”) at the default setting “01010”.
MS1251-E-00
22
2010/10
[AK4223]
SYSTEM DESIGN
Figure 22 shows a system connection diagram. An evaluation board [AKD4223] is available which demonstrates the
optimum layout, power supply arrangements and measurement results.
Digital Ground
Analog Ground
Micro
Controller
RIN2 38
VSS1 37
0.47u
0.47u
GND2 39
LIN4 33
0.47u
0.47u
0.47u
GND5 29
0.47u
RIN5 28
0.47u
LIN6 27
Video out
24 LOUT1
10u
300
23 ROUT1
22 LOUT2
21 ROUT2
10u
10u
300
10u
10u
0.1u
300
0.1u
10u
75
75
10u
300
20 RVDD
19 AVDD
15 VR1
18 VVDD
RIN6 25
17 RSTN
12 VR2
16 REGV
GND6 26
14 VOUT1
11 VIN1
Audio in
0.47u
LIN5 30
0.1u
0.1u
0.47u
RIN4 31
10 VGND1
0.1u
0.47u
GND4 32
9 VIN2
0.1u
VSS2
LIN2 40
0.47u
RIN1 41
0.47u
GND1 42
LIN1 43
SDA 45
4 VGND4
8 VGND2
0.1u
0.1u
75
RIN3 34
7 VIN3
0.1u
75
3 VIN5
6 VGND3
0.1u
0.47u
GND3 35
5 VIN4
0.1u
75
VCOM 44
0.47u
0.1u
0.47u
LIN3 36
2 VGND5
0.1u
0.1u
75
SCL 46
1 VIN6
0.1u
75
VSS2 47
75
13 VOUT2
Video In
VGND6 48
0.1u
0.47u
1u
Audio in
0.47u
0.47u
VSS1
Audio out
Analog 9V
Figure 22. Typical Connection Diagram
MS1251-E-00
23
2010/10
[AK4223]
1. Grounding and Power Supply Decoupling
The AK4223 requires careful attention to power supply and grounding arrangements. AVDD, VVDD and RVDD are
usually supplied from the analog power supply in the system. Alternatively if AVDD, VVDD and RVDD are supplied
separately, AVDD and RVDD must be powered-up at the same time. The power up sequence between AVDD/RVDD and
VVDD is not critical. VSS1 and VSS2 must be connected to the analog ground plane. System analog ground and digital
ground should be connected together near to where the supplies are brought onto the printed circuit board. Decoupling
capacitors should be as close to the power supply pin of AK4223 as possible.
2. Voltage Reference
VCOM is a signal ground of this chip. An 1μF electrolytic capacitor attached between VCOM and VSS1 eliminates the
effects of high frequency noise. No load current may be drawn from the VCOM pin. To avoid coupling to the AK4223, all
signals and especially clock signals should be kept away as far as possible from the VCOM pin.
3. Notes for Drawing a Board
Analog input and output pins should be as short as possible in order to avoid unwanted coupling into the AK4223. The
unused pins should be open.
MS1251-E-00
24
2010/10
[AK4223]
PACKAGE
48pin LQFP (Unit: mm)
1.70Max
9.0 ± 0.2
0.13 ± 0.13
7.0
36
1.40 ± 0.05
24
48
13
7.0
37
12
1
0.5
9.0 ± 0.2
25
0.22 ± 0.08
0.09 ∼ 0.20
0.10 M
0° ∼ 10°
0.10
0.3 ∼ 0.75
■ Package & Lead Frame Material
Package molding compound:
Lead frame material:
Lead frame surface treatment:
Epoxy
Cu
Solder (Pb free) plate
RoHS Compliance
*All integrated circuits form Asahi Kasei Microdevices Corporation (AKM) assembled in “lead-free”
packages are fully compliant with RoHS.
MS1251-E-00
25
2010/10
[AK4223]
MARKING
AK4223VQ
XXXXXXX
1
XXXXXXXX: Date code identifier
REVISION HISTORY
Date (YY/MM/DD)
10/10/22
MS1251-E-00
Revision
00
Reason
First Edition
Page
Contents
26
2010/10
[AK4223]
IMPORTANT NOTICE
z These products and their specifications are subject to change without notice.
When you consider any use or application of these products, please make inquiries the sales office of Asahi Kasei
Microdevices Corporation (AKM) or authorized distributors as to current status of the products.
z Descriptions of external circuits, application circuits, software and other related information contained in this
document are provided only to illustrate the operation and application examples of the semiconductor products. You
are fully responsible for the incorporation of these external circuits, application circuits, software and other related
information in the design of your equipments. AKM assumes no responsibility for any losses incurred by you or third
parties arising from the use of these information herein. AKM assumes no liability for infringement of any patent,
intellectual property, or other rights in the application or use of such information contained herein.
z Any export of these products, or devices or systems containing them, may require an export license or other official
approval under the law and regulations of the country of export pertaining to customs and tariffs, currency exchange,
or strategic materials.
z AKM products are neither intended nor authorized for use as critical componentsNote1) in any safety, life support, or
other hazard related device or systemNote2), and AKM assumes no responsibility for such use, except for the use
approved with the express written consent by Representative Director of AKM. As used here:
Note1) A critical component is one whose failure to function or perform may reasonably be expected to result,
whether directly or indirectly, in the loss of the safety or effectiveness of the device or system containing it, and
which must therefore meet very high standards of performance and reliability.
Note2) A hazard related device or system is one designed or intended for life support or maintenance of safety
or for applications in medicine, aerospace, nuclear energy, or other fields, in which its failure to function or
perform may reasonably be expected to result in loss of life or in significant injury or damage to person or
property.
z It is the responsibility of the buyer or distributor of AKM products, who distributes, disposes of, or otherwise places
the product with a third party, to notify such third party in advance of the above content and conditions, and the buyer
or distributor agrees to assume any and all responsibility and liability for and hold AKM harmless from any and all
claims arising from the use of said product in the absence of such notification.
MS1251-E-00
27
2010/10