AOZ8045 6-Line EMI Filter with Integrated ESD Protection General Description Features The AOZ8045 is a 6-line device integrating EMI filtering with ESD protection for each line. It is designed to suppress unwanted EMI/RFI signals and provide electrostatic discharge (ESD) protection in portable electronic equipment. This state-of-the-art device utilizes AOS leading edge Trench Vertical Structure [TVS]2 ™ technology for superior clamping performance and filter attenuation over the full operating display range. The AOZ8045 has been optimized for protection of color LCD displays and CCD camera lines in cellular phones and other portable consumer electronic devices. ● The AOZ8045 consists of six identical circuits comprised of TVS diodes for ESD protection, and a resistor–capacitor network for EMI/RFI filtering. A series resistor value of 100Ω and a capacitance value of 9pF are used to achieve -20dB minimum attenuation from 1.0GHz to 3.0GHz. The TVS diodes provide effective suppression of ESD voltages in excess of ±20kV (contact discharge) and ±20kV (air discharge). This exceeds IEC 61000-4-2, level 4 ESD immunity test. 6 lines for EMI filtering and ESD protection: – Exceeds IEC 61000-4-2, level 4 (ESD) immunity test – ±20kV (contact discharge) and ±20kV (air discharge) ● Trench Vertical Structure [TVS]2 ™ based technology used to achieve excellent ESD clamping and filter performance over the full operating display range ● Filter performance: -20db attenuation from 1.0GHz to 3.0GHz ● Low operating voltage: 5.0V ● Capacitance stability over wide range of voltages and temperatures ● DFN package 2.50mm x 1.20mm ● Pb-Free device Applications ● EMI filtering and ESD protection for data lines ● LCD displays, camera interface, I/O interface ● Portable handheld devices, cell phones, PDA phones The AOZ8045 comes in an RoHS compliant, 2.50mm x 1.20mm DFN package and is rated over a -40°C to +85°C ambient temperature range. Electrical Schematic D0 100Ω CH1 9pF 9pF 100Ω D1 D5 CH2 9pF LCD/Camera Module 9pF 100Ω CH6 9pF 9pF Figure 1. Rev. 1.2 July 2009 www.aosmd.com Page 1 of 7 AOZ8045 Ordering Information Part Number Ambient Temperature Range Package Environmental AOZ8045DI -40°C to +85°C DFN-12 RoHS Compliant Green Product AOS Green Products use reduced levels of Halogens, and are also RoHS compliant. Please visit www.aosmd.com/web/quality/rohs_compliant.jsp for additional information. Pin Configuration 1 12 2 11 3 3 10 4 4 9 5 8 6 7 1 11 2 10 9 8 Exposed Pad (GND) 12 5 6 7 DFN-12 (Bottom View) Top View Pin Description Rev. 1.2 July 2009 Pin Number Pin Name Pin Function 1,12 CH 1 Channel 1 Connections 2, 11 CH 2 Channel 2 Connections 3, 10 CH 3 Channel 3 Connections 4, 9 CH 4 Channel 4 Connections 5, 8 CH 5 Channel 5 Connections 6, 7 CH 6 Channel 6 Connections Exposed Pad GND Common Ground Connection www.aosmd.com Page 2 of 7 AOZ8045 Absolute Maximum Ratings Exceeding the Absolute Maximum ratings may damage the device. Parameter Rating Storage Temperature (TS) -65°C to +150°C ESD Rating per IEC61000-4-2, contact ESD Rating per IEC61000-4-2, air (1) ±20kV (1) ±20kV ESD Rating per Human Body Model(2) ±30kV Notes: 1. IEC 61000-4-2 discharge with CDischarge = 150pF, RDischarge = 330Ω. 2. Human Body Discharge per MIL-STD-883, Method 3015 CDischarge = 100pF, RDischarge = 1.5kΩ. Electrical Characteristics TA = 25°C unless otherwise specified. Symbol VRWM Parameter Reverse Working Voltage Conditions Max. Units 5.0 V 8 V 0.1 µA ILOAD = 1A, positive ILOAD = 1A, negative clamp(5)(8) 7.0 -3.0 V ILOAD = 5A, positive clamp(5)(8) ILOAD = 5A, negative clamp(5)(8) 8.0 -8.0 ILOAD = 12A, positive clamp(5)(8) ILOAD = 12A, negative clamp(5)(8) 10.0 -10.0 1mA(4) VBR Reverse Breakdown Voltage IT = IR Reverse Leakage Current VRWM = 3.3V VCL RCH CCH fC Signal Clamp Voltage Total Series Resistance Min. Typ. (3) 6 7 clamp(5)(8) IR = 20mA Ground(6)(7)(8) 90 100 110 Ω 8 9 10 pF Channel Capacitance Input to Cut-off Frequency Measured with 50Ω source and 50Ω load termination 250 MHz Attenuation from 1.0GHz to 3.0GHz VR = 0V Measured with 50Ω source and 50Ω load termination -20 dB Notes: 3. The working peak reverse voltage, VRWM, should be equal to or greater than the DC or continuous peak operating voltage level. 4. VBR is measured at the pulse test current IT. 5. Measurements performed using a 100ns Transmission Line Pulse (TLP) system. 6. Total capacitance is equal to 2 x CCH. 7. Measured at 25°C, VR = 2.5V, f = 1.0MHz. 8. Guaranteed by design. Rev. 1.2 July 2009 www.aosmd.com Page 3 of 7 AOZ8045 Typical Performance Characteristics Insertion Loss Characteristics Analog Crosstalk 0 0 -5 -10 -20 -20 S21 (db) S21 (db) -15 -25 -30 -40 -60 -35 -40 -80 -45 -50 1 10 100 1000 -100 10000 1 10 100 Frequency (MHz) 10000 Forward Voltage vs. Forward Current Clamping Voltage vs. Peak Pulse Current 11 12 10 10 Forward Voltage (V) Clamping Voltage, Vcl (V) 1000 Frequency (MHz) 9 8 8 6 4 7 2 6 0 2 4 6 8 10 0 12 2 4 6 8 10 12 Forward Current (A) Peak Pulse Current, Ipp (A) Typical Resistance vs. Temperature 110 Resistance (Ω) 105 100 95 90 -45 -25 -5 5 25 45 65 85 Temparature (°C) Rev. 1.2 July 2009 www.aosmd.com Page 4 of 7 AOZ8045 Package Dimensions, DFN 2.5 x 1.2, 12L EP1 S E E1 D D1 L 12x Pin 1 Marking b Pin 1 ID (C0.2x45°) e TOP VIEW BOTTOM VIEW A Dimensions in millimeters SIDE VIEW A1 A3 RECOMMENDED LAND PATTERN 1.80 0.15 0.35 Symbols A Min. 0.50 A1 b A3 0.00 0.15 D E 1.15 2.45 D1 D1 e 0.25 1.75 L 0.20 Nom. 0.55 Max. 0.60 Dimensions in inches Symbols A Min. 0.020 A1 b A3 0.000 0.006 1.25 2.55 D E 0.045 0.096 0.30 0.35 1.80 1.85 0.40 BSC D1 D1 e 0.010 0.069 L 0.008 — 0.05 0.20 0.25 0.152 REF 1.20 2.50 0.24 0.30 Nom. 0.022 Max. 0.024 — 0.002 0.008 0.010 0.006 REF 0.047 0.098 0.049 0.100 0.012 0.014 0.071 0.073 0.016 BSC 0.010 0.012 0.20 0.30 1.05 0.40 C0.15x45° 0.20 0.20 UNIT: mm Notes: 1. All dimensions are in millimeters. Converted inch dimensions are not necessarily exact. Rev. 1.2 July 2009 www.aosmd.com Page 5 of 7 AOZ8045 Tape and Dimensions, DFN 2.5 x 1.2 Carrier Tape P2 P1 D0 D1 E1 K0 E2 E B0 Ref 5° P0 T A0 A–A Feeding Direction UNIT: mm Package A0 B0 K0 DFN 2.5x1.2 1.45 ±0.05 2.80 ±0.05 0.70 ±0.05 D0 D1 ø1.55 ø0.80 ±0.05 ±0.05 E E1 E2 P0 P1 P2 T 8.00 ±0.03 1.75 ±0.1 3.50 ±0.05 4.00 ±0.10 4.0 ±0.10 2.0 ±0.05 0.30 ±0.05 Reel W1 S M K N G R H W UNIT: mm Tape Size Reel Size 8mm ø178 M N W W1 H S K E ø178.0 ±1.0 ø60.0 ±0.5 11.80 ±0.5 9.0 ±0.5 ø13.0 +0.5 / –0.2 2.40 ±0.1 10.25 ±0.2 ø9.8 Leader / Trailer & Orientation Trailer Tape 300mm Min. Rev. 1.2 July 2009 Components Tape Orientation in Pocket www.aosmd.com Leader Tape 500mm Min. Page 6 of 7 AOZ8045 Package Marking AOZ8045DI (DFN-12) 32V Part Number Code Underscore Denotes Green Product Assembly Location Code Week & Year Code This data sheet contains preliminary data; supplementary data may be published at a later date. Alpha & Omega Semiconductor reserves the right to make changes at any time without notice. LIFE SUPPORT POLICY ALPHA & OMEGA SEMICONDUCTOR PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury of the user. Rev. 1.2 July 2009 2. A critical component in any component of a life support, device, or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. www.aosmd.com Page 7 of 7