AOZ8010 8-Line EMI Filter with Integrated ESD Protection General Description Features The AOZ8010 is an 8-line device integrating EMI filtering with ESD protection for each line. It is designed to suppress unwanted EMI/RFI signals and provide electrostatic discharge (ESD) protection in portable electronic equipment. This state-of-the-art device utilizes AOS leading edge Trench Vertical Structure [TVS]2 ™ technology for superior clamping performance and filter attenuation over the full operating display range. The AOZ8010 has been optimized for protection of color LCD displays and CCD camera lines in cellular phones and other portable consumer electronic devices. ● The AOZ8010 consists of eight identical circuits comprised of TVS diodes for ESD protection, and a resistor–capacitor network for EMI/RFI filtering. A series resistor value of 100Ω and a capacitance value of 28pF are used to achieve -35dB minimum attenuation from 800MHz to 2.2GHz. The TVS diodes provide effective suppression of ESD voltages in excess of ±18kV (air discharge) and ±18kV (contact discharge). This exceeds IEC 61000-4-2, level 4 ESD immunity test. 8 lines for EMI filtering and ESD protection: – Exceeds IEC 61000-4-2, level 4 (ESD) immunity test – ±18kV (air discharge) and ±18kV (contact discharge) ● Trench Vertical Structure [TVS]2 ™ based technology used to achieve excellent ESD clamping & filter performance over the full operating display range ● Filter performance: -35db attenuation from 800MHz to 2.2GHz ● Low operating voltage: 5.0V ● Capacitance stability over wide range of voltages and temperatures ● TDFN or DFN package: 1.6 x 4.0mm ● Pb-free device Applications ● EMI filtering and ESD protection for data lines ● LCD displays, camera interface, I/O interface ● Portable handheld devices, cell phones, PDA phones The AOZ8010 comes in an RoHS compliant, 1.6mm x 4.0mm TDFN or DFN package and is rated over a -40°C to +85°C ambient temperature range. Typical Application D0 D1 D7 CH1 LCD/Camera Module CH2 CH8 Figure 1. Rev. 2.6 September 2009 www.aosmd.com Page 1 of 8 AOZ8010 Ordering Information Part Number Ambient Temperature Range Package Environmental AOZ8010DTL -40°C to +85°C TDFN-16 RoHS Compliant Green Product AOZ8010DIL* DFN-16 AOS Green Products use reduced levels of Halogens, and are also RoHS compliant. Please visit www.aosmd.com/web/quality/rohs_compliant.jsp for additional information. * Not recommended for new designs. Pin Configuration 1 15 2 14 3 Exposed Pad (GND) 16 13 12 11 4 5 1 16 2 15 3 14 4 13 5 12 6 11 7 10 8 9 6 10 7 9 8 TDFN-16/DFN-16 (Bottom View) Top View Pin Description Pin Number Pin Name Pin Function 1,16 CH 1 Channel 1 Connections 2, 15 CH 2 Channel 2 Connections 3, 14 CH 3 Channel 3 Connections 4, 13 CH 4 Channel 4 Connections 5, 12 CH 5 Channel 5 Connections 6, 11 CH 6 Channel 6 Connections 7, 10 CH 7 Channel 7 Connections 8, 9 CH 8 Channel 8 Connections Exposed Pad GND Common Ground Connection Rev. 2.6 September 2009 www.aosmd.com Page 2 of 8 AOZ8010 Absolute Maximum Ratings Exceeding the Absolute Maximum ratings may damage the device. Parameter Rating Storage Temperature (TS) -65°C to +150°C ESD Rating per IEC61000-4-2, contact ESD Rating per IEC61000-4-2, air (1) ±18kV (1) ±18kV ESD Rating per Human Body Model(2) ±30kV Notes: 1. IEC 61000-4-2 discharge with CDischarge = 150pF, RDischarge = 330Ω. 2. Human Body Discharge per MIL-STD-883, Method 3015 CDischarge = 100pF, RDischarge = 1.5kΩ. Electrical Characteristics TA = 25°C unless otherwise specified. Symbol VRWM Parameter Reverse Working Voltage Conditions 1mA(4) VBR Reverse Breakdown Voltage IT = IR Reverse Leakage Current VRWM = 3.3V 6 clamp(5)(8) VCL Signal Clamp Voltage ILOAD = 12A, positive ILOAD = 12A, negative clamp(5)(8) RCH Total Series Resistance IR = 20mA CCH fC Min. Typ. Max. Units 5.0 V 8 V 0.1 µA (3)(8) Ground(6)(7)(8) 7 9.5 -8.5 V 85 100 115 Ω 26 28 30 pF Channel Capacitance Input to Cut-off Frequency Measured with 50Ω source and 50Ω load termination 90 MHz Attenuation from 800MHz to 2.2GHz VR = 0V Measured with 50Ω source and 50Ω load termination -35 dB Attenuation from 800MHz to 2.2GHz VR = 5V Measured with 50Ω source and 50Ω load termination -35 dB Notes: 3. The working peak reverse voltage, VRWM, should be equal to or greater than the DC or continuous peak operating voltage level. 4. VBR is measured at the pulse test current IT. 5. Measurements performed using a 100ns Transmission Line Pulse (TLP) system. 6. Total capacitance is equal to 2 x CCH. 7. Measured at 25°C, VR = 2.5V, f = 1.0MHz. 8. Guaranteed by design. Rev. 2.6 September 2009 www.aosmd.com Page 3 of 8 AOZ8010 Typical Performance Characteristics Typical Line Capacitance vs. Reverse Bias Voltage (Normalized to Capacitance @ 2.5V) Insertion Loss Characteristics 2.0 1.8 -10 1.6 Normalized Capacitance (pF) 0 -5 -15 S21 (db) -20 -25 -30 -35 -40 -45 -50 1.4 1.2 1.0 0.8 0.6 0.4 0.2 1 10 100 1000 0 0.0 10000 1.0 Frequency (MHz) 2.0 3.0 4.0 5.0 Reverse Biased Voltage (V) Analog Crosstalk 0 Clamping Voltage vs. Peak Pulse Current (tperiod = 100ns, tr = 1ns) 12 Clamping Voltage, VCL (V) -20 S21 (db) -40 -60 -80 11 10 9 8 7 5 4 3 -100 0 1 10 100 1000 2 4 6 8 Peak Pulse Current, IPP (A) 10000 10 12 Frequency (MHz) Typical Resistance over Temperature 110 Forward Voltage vs. Forward Current (tperiod = 100ns, tr = 1ns) 108 106 8 Resistance (Ω) Forward Voltage (V) 10 6 4 104 102 100 98 2 96 0 0 2 4 6 8 10 12 94 -40 -30 -20 -10 Forward Current (A) 0 5 15 25 35 45 55 65 75 85 Temperature (°C) Insertion Loss vs. DC Bias 0 -5 Insertion Loss abs (db) -10 -15 -20 -25 -30 -35 -40 -45 -50 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 DC Bias (Volts) Rev. 2.6 September 2009 www.aosmd.com Page 4 of 8 AOZ8010 Package Dimensions, TDFN 1.6 x 4.0, 16L D D1 b E1 E L e Pin 1 Marking TOP VIEW Pin #1 ID Chamfer 0.2 x 45° BOTTOM VIEW A c A1 SIDE VIEW Dimensions in millimeters RECOMMENDED LAND PATTERN 3.30 0.25 0.45 1.35 Symbols A A1 b c D E D1 E1 e L Min. 0.50 0.00 0.20 Nom. Max. 0.55 0.60 — 0.05 0.25 0.30 0.152 REF. 3.95 4.00 4.05 1.55 1.60 1.65 3.15 3.20 3.25 0.40 0.45 0.50 0.50 BSC 0.25 0.30 0.35 Dimensions in inches Symbols A A1 b c D E D1 E1 e L Min. Nom. Max. 0.020 0.022 0.024 0.000 — 0.002 0.008 0.010 0.012 0.006 REF. 0.156 0.157 0.159 0.061 0.063 0.065 0.124 0.126 0.128 0.016 0.018 0.020 0.020 BSC 0.010 0.012 0.014 0.675 0.25 0.50 0.35 UNIT: mm Note: 1. Controlling dimension is millimeter. Converted inch dimensions are not necessarily exact. Rev. 2.6 September 2009 www.aosmd.com Page 5 of 8 AOZ8010 Package Dimensions, DFN 1.6 x 4.0, 16L (Not recommended for new designs) D B bbb A CAB e b 16 16 R E1 E aaa C 1 aaa C L 2x 1 2x D1 TOP VIEW BOTTOM VIEW A ccc C A1 c ddd C Seating B Plane SIDE VIEW Dimensions in millimeters Symbols A A1 b c D D1 E E1 e L R aaa bbb ccc ddd RECOMMENDED LAND PATTERN 3.20 0.45 1.30 0.30 0.25 0.50 UNIT: mm Min. 0.70 0.00 0.18 0.15 Nom. 0.75 0.02 0.25 0.20 4.00 BSC 3.05 3.20 1.60 BSC 0.30 0.45 0.50 BSC 0.20 0.30 0.10 0.15 0.10 0.10 0.08 Max. 0.80 0.05 0.30 0.25 3.30 0.55 0.40 Dimensions in inches Symbols A A1 b c D D1 E E1 e L R aaa bbb ccc ddd Min. 0.028 0.000 0.007 0.006 Nom. Max. 0.030 0.031 0.001 0.002 0.010 0.012 0.008 0.010 0.157 BSC 0.120 0.126 0.130 0.063 BSC 0.012 0.018 0.022 0.020 BSC 0.008 0.012 0.016 0.004 0.006 0.004 0.004 0.003 Notes: 1. Dimensions and tolerancing conform to ASME Y14.5M-1994. 2. All dimensions are in millimeters. 3. Dimension b applies to metallized terminal and is measured between 0.10mm and 0.30mm from the terminal tip. If the terminal has the optional radius on the other end of the terminal, the dimension b should not be measured in that radius area. 4. Coplanarity ddd applies to the terminals and all other bottom surface metallization. Rev. 2.6 September 2009 www.aosmd.com Page 6 of 8 AOZ8010 Tape and Reel Dimensions, TDFN/DFN 1.6 x 4.0 Carrier Tape P2 P1 B D1 D0 E1 K0 R0.3 Max. E2 E B0 5° Max A0 P0 T B Feeding Direction Unit: mm Package DFN 4x1.6 A0 2.00 ±0.1 B0 4.40 ±0.1 K0 0.95 ±0.1 D0 ø1.50 +0.1/-0 D1 ø1.00 +0.1/-0 E 12.00 ±0.3 E1 1.75 ±0.10 Reel E2 5.50 ±0.1 P0 4.00 ±0.10 P1 4.00 ±0.10 P2 2.00 ±0.10 T 0.30 ±0.05 W1 S R K M N H Unit: mm Tape Size Reel Size 12mm ø330 M ø330.00 ±0.30/-4.00 N 55.00 ±0.40 W1 12.4 +2.0/-0 H 13.00 ±0.20 S 2.20 ±0.20 K 10.60 ±0.20 R — Leader / Trailer & Orientation Trailer Tape 300mm min. Rev. 2.6 September 2009 Components Tape Orientation in Pocket www.aosmd.com Leader Tape 500mm min. Page 7 of 8 AOZ8010 ΩPackage Marking AOZ8010DTL (1.6 x 4.0 TDFN) P N OWL T Part Number Code Underscore Denotes Green Product Assembly Lot Code Week and Year Code Assembly Location Code AOZ8010DIL* (1.6 x 4.0 DFN) P N OWL T Part Number Code Underscore Denotes Green Product Assembly Lot Code Week and Year Code Assembly Location Code * Not recommended for new designs. This data sheet contains preliminary data; supplementary data may be published at a later date. Alpha & Omega Semiconductor reserves the right to make changes at any time without notice. LIFE SUPPORT POLICY ALPHA & OMEGA SEMICONDUCTOR PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury of the user. Rev. 2.6 September 2009 2. A critical component in any component of a life support, device, or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. www.aosmd.com Page 8 of 8