BRIGHT VIEW ELECTRONICS CO.,LTD ULTRA BRIGHTNESS SMD LED BVS-166WT2 PACKAGE CONFIGURATION Cathode mark LED die 0.8 0.6 Soldering terminal Cathode line 1.6 1.0 Soldering Pattem 0.8 0.8 1.0 0.4 0.8 Polarity P C .board 0.3 0.7 0.8 0.4 Soldering terminal Resin DESCRIPTION Tolerance ± 0.1 р Dice Material : InGaN Blue Light Color : White Color Lens Color : Yellow Diffused ABSOLUTE MAXIMUM RATINGS AT Ta = 25 к PARAMETER MAX. 80 20 80 5 0.35 Ё30 to Ѐ 80 Ё40 to Ѐ 85 Power Dissipation Continuous Forward Current Peak Forward Current ( 1/10 Duty Cycle , 0.1ms Pulse Width ) Reverse Voltage Derating Linear From 25 к Operating Temperature Range Storage Temperature Range Infrared Soldering Condition 260 к for 5 seconds Reflow Soldering Condition 230 к for 10 seconds ELECTRICAL / OPTICAL CHARACTERISTICS AT Ta = 25 PARAMETER SYMBOL VF Forward Voltage Reverse Current IR Viewing Angle 2Ӱ1/2 TEST COND. I F = 20 mA V R = 5V I F = 20 mA UNIT mW mA mA V mA/oC o C o C к MIN. TYP. 3.2 MAX. 4 10 UNIT V ӴA Deg 140 BIN GRADE LIMITS ( I F = 20 mA ) CHROMATICITY COORDINATES WA WB x y x y 0.26 0.22 0.29 0.26 0.26 0.26 0.29 0.30 0.29 0.30 0.32 0.34 0.29 0.26 0.32 0.30 One delivery will include three different ranks of products. WC WD 0.32 0.30 0.35 0.34 0.32 0.34 0.35 0.38 0.35 0.38 0.38 0.42 0.35 0.34 0.38 0.38 Measurement Uncertainty of the color coordinates : ±0.02 BIN GRADE LIMITS ( I F = 20 mA ) LUMINOUS INTENSITY / mcd D E F G H I Bin 218 280 360 465 600 780 Min. Max. 280 360 465 600 780 1000 Measurement Uncertainty of the Luminous Intensity : ± 15 % x y x y *Bright View reserves the rights to alter specifications and remove availability of products at any time without notice. *These products are sensitive to static electricity. Caution must be taken strictly to avoid static electricity. *Chromaticity Coordinates , x.y is according to CIE Chromaticity Diagram base on color of the device. *Ӱ1/2 is the off-axis angle where the luminous intensity is one half the on-axis intensity. 2005/7/22 – B BRIGHT VIEW LIGHT EMITTING DIODE ELECTRONICS CO.,LTD ӳ ӳ TTJMAX =130± C JMAX= 130 ± C BRIGHT VIEW ELECTRONICS CO.,LTD CAUTION FOR STATIC ELECTRICITY 靜電防治 These products are Gallium Nitride(GaN) or Indium Gallium Nitride(InGaN) light emitting diodes(LEDs). There are extremely sensitive to static electricity ESD damage. The user must take absolutely secure countermeasures against static electricity and surge when handling products. 顯明 LED 晶片材質為 Gallium Nitride(GaN)或 Indium Gallium Nitride(InGaN)，此材質對於靜電極為敏感，十分 容易受靜電衝擊而產生破壞，使用者接觸產品時必需做好對靜電衝擊之防護措施。 Bright View Blue, Green, White are GaN or InGaN materials are ESD classified, any manufacturing or workstations where GaN or InGaN devices are handled should be rated at〝Class1〞50V maximum. 顯明之藍、綠、白光晶片材質為 GaN 或 InGaN ，此材質屬 ESD 規範，任何 GaN 或 InGaN 產品所會被接 觸的製造或工作站必須控制在 50V 以下。 Proper grounding of products (via 1MΩ), use of conductive mat, semiconductive working uniform and shoes, and semiconductive containers are considered to be effective as countermeters against static electricity and surge. 適當的產品接地（1MΩ）與使用導電桌墊，並評估考慮穿著防靜電工作服、防靜電鞋與防靜電盒來有效地 防制靜電之衝擊。 An ionizer is recommended to be used in the facility or environment where static electricity may be generated easily, and soldering iron with a grounded tip is also recommended. 建議對於工廠設施與環境中容易產生靜電的地點使用離子風扇吹拂，且也建議使用有接地功能的烙鐵進行 焊接。 To install a protection device, in the LED driving circuit, which does not exceed the max rating for surge current during on/off switching. 在驅動 LED 的電路上設置保護裝置，使其當開閉時的瞬間電流不會超出最大電壓值。 2003/03/04 -A BRIGHT VIEW ELECTRONICS CO.,LTD SMD APPLICATION ( PB FREE SOLDERING ) Apply to BVS-3XX、1XX series. Description: (1) Manual soldering (We do not recommend this method strongly.) (1.1) To prevent cracking,please bake (65℃,24hrs)before soldering. (1.2) Temperature at tip of iron: 250℃ Max.(25W) (1.3) It's banned to load any stress on the resin during soldering. (1.4) Soldering time: 3 sec. Max.(one time only) (2) Reflow Soldering (2.1) To prevent cracking,please bake (65℃,24hrs)before soldering. (2.2) When soldering,do not put stress on the LEDs during heating. (2.3) Never take next process until the component is cooled down to room temperature after reflow. (2.4) After soldering,do not warp the circuit board. (2.5) The recommended reflow soldering profile(measuring on the surface of the LED resin)is following: 10 SEC. MAX. 245 C MAX. 0.5℃/SEC MAX. 217℃ 217℃ TEMPERATURE 150℃ 1℃/SEC. MAX. 50 SEC. MAX. ~75℃ ~25℃ 210 SEC. MIN. 100 SEC. MAX. TIME The reflow temperature 240℃~245℃ is recommended and the soldering temperature should be not higher than 245℃(one time only) DOC. NO.:S-QW-K002 2006 / 02 / 08 - C BRIGHT VIEW CHIP LEDS PACKING ELECTRONICS CO.,LTD BVS-166/167 Series 2.0 Cathode mark 0.05 4.0 0.10 4.0 1.5 0.10 0.10 0.23 0.05 1.75 0.10 3.5 0.05 1.80 0.10 8.0 0.20 Feeding direction UNIT : mm 0.75 0.10 - BVS-166 0.60 0.10 - BVS-167 178 1.0 60 0.5 Reel : 4,000PCS 12 0.5 UNIT : mm Label 2 Bright View Label 1 Bright View PART NO.: PART NO.: Electronics Co.,Ltd. BVS-16XXXX LOT NO.: GRADE: Q'ty LOT NO.: GRADE: Q'ty X- pcs QA ńłŖŕŊŐŏ pcs Electronics Co.,Ltd. QA ELECTROSTATIC SENSITIVE DEVICES DO NOT OPEN OR HANDLE EXCEPT AT A STATIC-FREE WORKSTATION 24 Anti-electrostatic bag Normal X: Bin grade : Wavelength : Vf 39 RE CARTON Dimension(cm): 39*24*22 22 ITEM NO. DEVICE: Q'TY N. W.: G. W.: Y PCS. KGS. KGS. Carton : 30 Reels Total : 120,000PCS 2003 / 11 / 12 - A