FDA215 MOSFET Driver Parameter Typical Open Circuit Voltage Typical Short Circuit Current Input Control Current Rating 5.5 2.5 5 Units V A mA Features • Optically Isolated, Input to Output • Dual Independent, Floating Outputs for Parallel, Series, or Isolated Configuration • 5mA Control Current • May Be Configured for AC and DC Switching • Replacement of Discrete Components • VDE Compatible • Solid State Reliability • No EMI/RFI Generation • Machine Insertable, Wave Solderable • Surface Mount and Tape & Reel Version Available Description The FDA215 is a dual photovoltac MOSFET driver that uses a pair of optically coupled GaAIAs LEDs to drive two photodiode arrays. When the input current is applied to the LED, the light emitted activates the photodiode array, and generates a voltage at the output. The photodiode arrays are capable of generating a floating source voltage and current sufficient to drive high power MOSFET transistors. The optical coupling provides a high level of input to output isolation. The FDA215 is well suited for use in discrete solid state relay designs and other isolated switching applications. Approvals • EN/IEC 60950-1 Certified Component: TUV Certificate B 10 05 49410 006 Ordering Information Applications • MOSFET Driver • Programmable Control • Process Control • Instrumentation • Telecommunications Part # FDA215 FDA215S FDA215STR Description 8-Pin DIP (50/tube) 8-Pin Surface Mount (50/tube) 8-Pin Surface Mount (1000/reel) Pin Configuration 1 Input 2 3 Input 4 Pb RoHS 2002/95/EC DS-FDA215-R05 + – P V – 8 Output + 7 + – P V – + 6 Output 5 e3 www.clare.com 1 FDA215 Absolute Maximum Ratings @ 25ºC Parameter Reverse Input Voltage Input Control Current Peak (10ms) Input Power Dissipation 1 Total Power Dissipation 2 Capacitance, Input to Output Isolation Voltage, Input to Output Operational Temperature Storage Temperature 1 Derate linearly 1.33 mW / ºC 2 Derate linearly 6.67 mW / ºC Ratings 5 100 1 150 500 1 3750 -40 to +85 -40 to +125 Units V mA A mW mW pF Vrms °C °C Absolute Maximum Ratings are stress ratings. Stresses in excess of these ratings can cause permanent damage to the device. Functional operation of the device at conditions beyond those indicated in the operational sections of this data sheet is not implied. Electrical Characteristics @ 25ºC Parameter Output Characteristics Open Circuit Voltage Short Circuit Current Switching Speeds Turn-On Turn-Off Offstate Clamping Resistance Input Characteristics Input Control Current Input Voltage Drop Reverse Input Current Common Characteristics Capacitance, Input to Output 2 Conditions Symbol Min Typ Max Units IF=5mA IF=5mA IF=25mA VOC 5.5 2.5 3.5 8 9 20 V ISC 3 1 2.5 VL=1V ton toff RCL 100 250 5 5 3300 IF=5mA VR=5V IF VF IR 0.9 - 1.2 - 5 1.4 10 mA V µA - - - 3 - pF IF=5mA, CLOAD=200pF www.clare.com A ms R05 FDA215 Manufacturing Information Moisture Sensitivity All plastic encapsulated semiconductor packages are susceptible to moisture ingression. Clare classified all of its plastic encapsulated devices for moisture sensitivity according to the latest version of the joint industry standard, IPC/JEDEC J-STD-020, in force at the time of product evaluation. We test all of our products to the maximum conditions set forth in the standard, and guarantee proper operation of our devices when handled according to the limitations and information in that standard as well as to any limitations set forth in the information or standards referenced below. Failure to adhere to the warnings or limitations as established by the listed specifications could result in reduced product performance, reduction of operable life, and/or reduction of overall reliability. This product carries a Moisture Sensitivity Level (MSL) rating as shown below, and should be handled according to the requirements of the latest version of the joint industry standard IPC/JEDEC J-STD-033. Device Moisture Sensitivity Level (MSL) Rating FDA215 / FDA215S MSL 1 ESD Sensitivity This product is ESD Sensitive, and should be handled according to the industry standard JESD-625. Reflow Profile This product has a maximum body temperature and time rating as shown below. All other guidelines of J-STD-020 must be observed. Device Maximum Temperature x Time FDA215 / FDA215S 250ºC for 30 seconds Board Wash Clare recommends the use of no-clean flux formulations. However, board washing to remove flux residue is acceptable. Since Clare employs the use of silicone coating as an optical waveguide in many of its optically isolated products, the use of a short drying bake may be necessary if a wash is used after solder reflow processes. Chlorine-based or Fluorine-based solvents or fluxes should not be used. Cleaning methods that employ ultrasonic energy should not be used. Pb R05 RoHS 2002/95/EC e3 www.clare.com 3 FDA215 MECHANICAL DIMENSIONS FDA215S 9.652 ± 0.381 (0.380 ± 0.015) 2.540 ± 0.127 (0.100 ± 0.005) 0.635 ± 0.127 (0.025 ± 0.005) 3.302 ± 0.051 (0.130 ± 0.002) 9.525 ± 0.254 (0.375 ± 0.010) 6.350 ± 0.127 (0.250 ± 0.005) 0.457 ± 0.076 (0.018 ± 0.003) PCB Land Pattern 2.54 (0.10) 8.90 (0.3503) 1.65 (0.0649) 7.620 ± 0.254 (0.300 ± 0.010) 0.254 ± 0.127 (0.010 ± 0.0005) 0.65 (0.0255) 4.445 ± 0.127 (0.175 ± 0.005) Dimensions mm (inches) 0.813 ± 0.120 (0.032 ± 0.004) FDA215S Tape & Reel 330.2 DIA. (13.00 DIA.) Top Cover Tape Thickness 0.102 MAX. (0.004 MAX.) K0 =4.90 (0.193) Ao=10.30 (0.406) K1 =4.20 (0.165) Embossed Carrier Embossment 4 W=16.00 (0.63) Bo=10.30 (0.406) P=12.00 (0.472) User Direction of Feed Dimensions mm (inches) NOTES: 1. Dimensions carry tolerances of EIA Standard 481-2 2. Tape complies with all “Notes” for constant dimensions listed on page 5 of EIA-481-2 www.clare.com R05 FDA215 FDA215 2.540 ± 0.127 (0.100 ± 0.005) 9.652 ± 0.381 (0.380 ± 0.015) PCB Hole Pattern 7.620 ± 0.254 (0.300 ± 0.010) 8-0.800 DIA. (8-0.031 DIA.) 2.540 ± 0.127 (0.100 ± 0.005) 9.144 ± 0.508 (0.360 ± 0.020) 6.350 ± 0.127 (0.250 ± 0.005) 6.350 ± 0.127 (0.250 ± 0.005) 0.457 ± 0.076 (0.018 ± 0.003) 4.064 TYP (0.160) 3.302 ± 0.051 (0.130 ± 0.002) 7.239 TYP. (0.285) 0.254 TYP (0.01) 7.620 ± 0.127 (0.300 ± 0.005) 0.889 ± 0.102 (0.035 ± 0.004) 7.620 ± 0.127 (0.300 ± 0.005) Dimensions mm (inches) For additional information please visit our website at: www.clare.com Clare, Inc. makes no representations or warranties with respect to the accuracy or completeness of the contents of this publication and reserves the right to make changes to specifications and product descriptions at any time without notice. Neither circuit patent licenses nor indemnity are expressed or implied. Except as set forth in Clare’s Standard Terms and Conditions of Sale, Clare, Inc. assumes no liability whatsoever, and disclaims any express or implied warranty, relating to its products including, but not limited to, the implied warranty of merchantability, fitness for a particular purpose, or infringement of any intellectual property right. The products described in this document are not designed, intended, authorized or warranted for use as components in systems intended for surgical implant into the body, or in other applications intended to support or sustain life, or where malfunction of Clare’s product may result in direct physical harm, injury, or death to a person or severe property or environmental damage. Clare, Inc. reserves the right to discontinue or make changes to its products at any time without notice. Specification: DS-FDA215-R05 ©Copyright 2011, Clare, Inc. OptoMOS® is a registered trademark of Clare, Inc. All rights reserved. Printed in USA. 5/11/2011 5