DIALIGHT 433-2170

ITE Compliant LED Signal Modules
Designed in the U.S.A
Meets Buy American provision under the
American Recovery and Reinvestment Act 2009
For projects requiring Buy American provision certification, consult factory for
additional information and special ordering details
ITE Compliant LED Traffic Signal Module Performance Specifications
All LED Ball Signal Modules (8 inch (200mm) and 12 inch (300mm)
shall be fully compliant to the ITE VTCSH LED Circular Supplement specifications dated and adopted June
27, 2005. Compliance to the ITE VTCSH-2 Interim Purchase Specification is not sufficient, and will not
substitute for compliance to the ITE VTCSH LED Circular Supplement specifications. Additionally, prior to bid
award, the manufacturer shall submit to purchaser, reports from ETL/Intertek, that certify full compliance of
all LED ball signal modules to the entire ITE specification. These tests should include but not be limited to
the luminous intensity measurements and requirements outlined in the ITE specification sections 6.4.4
through 6.4.4.4.2 (25°C and 74°C / 49°C). Evidence of full compliance to all required testing methods,
procedures and sections as outlined in the above ITE document Figure 2, Design Qualification Testing Flow
Chart must be included without any exceptions, changes or omissions. The manufacturer must also submit
a data sheet showing the exact catalog number of the items submitted on the bid and the Independent
Lab report must show full qualification of this catalog number.
To ensure optimal quality of illumination; uniformity; reliability; and appearance, all ball traffic signal
modules shall utilize Hi-flux LEDs rated at 1-watt or higher, as their source of illumination. To ensure
competency of design and manufacturing, manufacturers of ball, arrow, and pedestrian signal modules
shall have a minimum of 7 years of experience in utilizing Hi-flux LEDs rated at 1-watt or higher, as the source
of illumination in their ball traffic signal modules. Additionally, manufacturers must have utilized in excess of
20 million Hi-flux LEDs in their LED traffic signal modules during the most recent 10 year period.
All LED 12 inch (300 mm) Arrow Signal Modules
shall be fully compliant to the “Omni-directional” specifications of the ITE VTCSH - LED Vehicle Arrow Traffic Signal Supplement adopted July 1, 2007.
Additionally, prior to bid award, the manufacturer shall submit to purchaser, reports from ETL/Intertek that certify full compliance of all LED Arrow signal
modules. These tests should include but not be limited to the luminous intensity measurements and requirements outlined in the ITE specification
sections 6.4.4 through 6.4.4.4.2 (25°C and 74°C / 49°C). Evidence of full compliance to all required testing methods, procedures and sections as
outlined in the above ITE document Attachment 1, “Design Qualification Testing Flow Chart” must be included without any exceptions, changes or
omissions The manufacturer must also submit a data sheet showing the exact catalog number of the items submitted on the bid and the Independent
Lab report must show full qualification of this catalog number.
All LED 16x18 Countdown Pedestrian Signal Modules
shall be fully compliant to the ITE PTCSI Part-2: LED Pedestrian Traffic Sig nal Modules specifications adopted August 4, 2010 or the latest adopted version
as listed on the ITE website at time of bid. Additionally, prior to bid award, the manufacturer shall submit to purchaser, reports from ETL/Intertek that certify
full compliance of LED signal modules, to these specifications. Evidence of full compliance to all required testing methods, procedures and sections as
outlined in the above ITE document Attachment 2, “Design Qualification Testing Flow Chart” must be included without any exceptions, changes or
omissions. The manufacturer must also submit a data sheet showing the exact catalog number of the items submitted on the bid and the Independent
Lab report must show full qualification of this catalog number. Combination hand/person pedestrian signal modules shall incorporate separate power
supplies for the hand and the person icons.
In addition to, and in excess of the above applicable ITE specification compliance, the on-board circuitry of all LED traffic signal modules shall include
voltage surge protection, to withstand high-repetition noise transients and low-repetition high-energy transients as stated in Section 2.1.8, NEMA Standard
TS 2-2003. In addition, the module shall comply with the following standards: IEC 1000-4-5 at 3kV with a 2 ohm source impedance, ANSI/IEEE
C62, 41-2002; IEC 61000-4-12 (6kV, 200A, 100kHz ring wave).
Warranty:
Manufacturer shall provide at time of bid, a written warranty which provides for repair or replacement of modules that fail to function as intended due to
workmanship or material defects within the first 60 months from date of delivery. Modules which exhibit luminous intensities less than the minimum as
specified in the ITE specifications as indicated above, within the first 60 months from date of delivery shall be replaced or repaired.
Notes:
CSA approved to the following applicable requirements:
CSA Standard C22.2 No. 9.0-96 General Requirements for Luminaires
CSA Std. No. C22.2 No. 250.0-04 Luminaires
UL Std. No. 1598-2004 (May 2006) Luminaires
Designed in the U.S.A
Meets Buy American provision
under the American Recovery and
Reinvestment Act 2009
For projects requiring Buy American provision certification,
consult factory for additional information
and special ordering details
www.dialight.com
Uniform Appearance LED Traffic Signal Modules
Part Number
433-1110-003XL
433-1170-003XL
433-3130-901XL
433-3170-901XL
433-2120-001XL
433-2170-001XL
433-1210-003XL
433-1270-003XL
433-3230-901XL
433-3270-901XL
433-2220-001XL
433-2270-001XL
p
p
*Fully compliant to ITE VTCSH-LED Circular Signal Supplement dated 6/27/2005
Industry’s lowest power for all colors
p
p
p
p
p
p
p
p
p
p
p
Meets or exceeds ITE intensity, color and uniformity specification, including 49ºC / 74ºC requirements
Temperature compensated power supplies for longer LED life
Uniform appearance
Expanded view radiation pattern suitable for span wire and steep grade applications
Transient suppression exceeds ITE and NEMA specifications (Up to 6KV ring wave)
Manufactured with anti-capillary wires
Conformal coated power supply
Secondary lens treatment for abrasion resistance
Patent No. 7,281,818 and other patents pending
Intertek/ETL certified and listed on ETL certification program
All units operate at 80-135VAC RMS, 60±3Hz
Color
Lens
Type
Dominant
Wavelength
(nm)
Typical
Wattage
at 25°C
Peak Minimum
Maintained
Luminous Intensity (cd)
*Meets ITE VTCSH
LED Circular Signal
Supplement
CSA
Approved
Size
(in)
Red
Red
Yellow
Yellow
Green
Green
Red
Red
Yellow
Yellow
Green
Green
Tinted
Clear
Tinted
Clear
Tinted
Clear
Tinted
Clear
Tinted
Clear
Tinted
Clear
625
625
590
590
500
500
625
625
590
590
500
500
6
6
7
7
8
8
6
6
12
12
7
7
165
165
410
410
215
215
365
365
910
910
475
475
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
8
8
8
8
8
8
12
12
12
12
12
12
OMNI-DIRECTIONAL, UNIFORM APPEARANCE LED ARROWS
p
p
p
p
*Fully compliant to ITE VTCSH-LED Vehicle Arrow Supplement dated 7/01/2007
Allows for mounting in any orientation in the signal head
Industry’s lowest power for all colors
Meets or exceeds ITE intensity, color and uniformity specification, including 49ºC / 74ºC
requirements
p Temperature compensated power supplies for longer LED life
p Uniform appearance
p Transient suppression exceeds ITE and NEMA specifications (Up to 6KV ring wave)
p Manufactured with anti-capillary wires
p Conformal coated power supply
p Secondary lens treatment for abrasion resistance
p Intertek/ETL certified and listed on ETL certification program
p All units operate at 80-135VAC RMS, 60±3Hz
Part Number
432-1314-001XOD
Color
Lens Type
Typical
Wattage
at 25oC
Dominant
Wavelength
(nm)
Peak Minimum
Maintained Luminous
Intensity (cd)
*Meets ITE
Spec
CSA
Approved
Red
Tinted
6
628
56.8
a
a
432-1374-001XOD
Red
Clear
6
628
56.8
a
a
431-3334-901XOD
Yellow
Tinted
6
590
141.6
a
a
431-3374-901XOD
Yellow
Clear
6
590
141.6
a
a
432-2324-001XOD
Green
Tinted
6
500
73.9
a
a
432-2374-001XOD
Green
Clear
6
500
73.9
a
a
www.dialight.com
Uniform Appearance Hand and Person Pedestrian Signals
p
*Fully compliant to ITE PTCSI Part 2 LED Pedestrial Traffic Signal Module Specification adopted 3/9/04
p
Meets / exceeds ITE uniformity ratio of not more than 1 to 5 between the max and min luminance values as
p
p
p
Manufactured with anti-capillary wires
Conformal coated power supply
Fuse and transient suppressor incorporated for superior line and load protection
p
Independent dedicated power supplies for added safty and reliability
p
Intertek/ETL certified and listed on ETL certification program
measured in (.5”) dia spots
p Transient suppression exceeds ITE and NEMA specifications (Up to 6KV ring wave)
p All units operate at 80-135VAC RMS, 60±3Hz
Part Number
Size
Description
Typical Wattage
@ 25ºC
Min. Luminance
(cd/m2)
Hand
Hand
Person
*Meets ITE
Spec
CSA
Approved
Person
430-6450-001X
16 x 18
Side-by-side Hand and Person
8
7
1,400
2,200
a
a
430-6472-001X
16 x 18
Overlay Hand and Person
8
6
1,400
2,200
a
a
430-5770-001X
12 x 12
Hand only
8
N/A
1,400
N/A
a
a
430-7771-001X
12 x 12
Person only
N/A
7
N/A
2,200
a
a
430-6772-001X
12 x 12
Overlay Hand and Person
8
6
1,400
2,200
a
a
430-5570-001X
9x9
Hand only
6
N/A
1,400
N/A
a
430-7570-001X
9x9
Person only
N/A
6
N/A
2,200
a
Uniform Appearance Countdown Pedestrian Signals
Part
Number
Housing
Size
p
p
p
p
*Fully compliant to ITE PTCSI Part 2 LED Pedestrial Traffic Signal Module Specification adopted 8/04/2010
MUTCD compliant for coundown applications
Full preemption compatibility
Up to 8 units can be connected in parallel without affecting of the monitoring of the Hand/Person
p
p
p
p
Manufactured with anti-capillary wires
Three (3) Independent dedicated power supplies for added safty and reliability
Intertek/ETL certified and listed on ETL certification program
Reduced off state icon visibility results in increased pedestrian safety by eliminating the potential to
misinterpret the signal
p
p
p
Conformal coated power supply
New improved one piece housing design
Improved optical design to provide superior uniform appearance of the icons
p
p
Transient suppression exceeds ITE and NEMA specifications (Up to 6KV ring wave)
All units operate at 80-135VAC RMS, 60±3Hz
Symbol Color
Min. Luminance
(cd/m2)
Typical Wattage @ 25ºC
Countdown
Hand
Person Countdown
Hand
Person Countdown
430-6479-001X 16 x 18
Portland
Orange
Portland
Orange
Lunar
White
8
11
10
430-7773-001X 12 x 12
Portland
Orange
N/A
N/A
5
N/A
N/A
Hand
Person
1,400
1,400
2,200
1,400
N/A
N/A
*Meets ITE
CSA
Approved
Spec
a
a
a
Special Applications: Upon customer request, above units are available with option to countdown the clearance mode and the walk mode. Add
suffix “W” to above part numbers.
IMPORTANT NOTE: MUTCD DOES NOT recommend the use of a countdown timer in the “walk” mode
Dialight reserves the right to make changes at any time in order to supply the best product possible.
The most current version of this document will always be available at:
www.dialight.com/Assets/Brochures_And_Catalogs/Signaling/ITE_Spec_Brochure.pdf
ITE_Spec_Brochure_L
www.dialight.com