ITE, Caltrans, and California Energy Commission Approved LED Signal Modules and Pedestrian Signals Designed in the U.S.A Meets Buy American provision under the American Recovery and Reinvestment Act 2009 For projects requiring Buy American provision certification, consult factory for additional information and special ordering details California Energy Commission Approved LED Traffic Signal Modules All of the LED traffic modules featured in this brochure are fully certified to the requirements of the State of California’s Appliance Efficiency Program. Dialight is the first LED signal module manufacturer to fully support these requirements and has received certification for both Caltrans and ITE approved products. According to the section in CEC requirements entitled “Traffic Signals for Vehicle and Pedestrian Control” all Federally regulated traffic signals for vehicle and pedestrian control manufactured on or after January 1, 2006 shall have a nominal wattage and maximum wattage no greater than the values shown in table M-1, and shall be installed with the compatible electrically connected signal control interface devices and conflict monitoring systems”. CEC also has additional requirements for pedestrian signals that are not federally regulated. These requirements can be found in table M-2 of the CEC requirements. For reference a copy of tables M-1 and M-2 from the CEC requirements are shown below. Table M-1 Standards for Traffic Signals for Vehicle and Pedestrian Control Appliance Maximum Wattage (at 74°C) Nominal Wattage (at 25°C) 17 13 12 15 12 11 11 8 9 15 12 11 16 12 16 13 9 13 Traffic Signal Module Type 12 - inch Red Ball 8 - inch Red Ball 12 - inch Red Arrow 12 - inch Green Ball 8 - inch Green Ball 12 - inch Green Arrow Pedestrian Module Type Combination Walking Man/Hand Walking Man Orange Hand Table M-2 Standards for Signal Modules for Pedestrian Control Sold or Offered for Sale in the State of California Maximum Wattage (at 74°C) 12 12 Appliance Hand or ‘Dont Walk’ sign or Countdown Walking Person or ‘Walk’ sign Nominal Wattage (at 25°C) 10 9 ITE and Caltrans Approved LED ARROWS • Allows for mounting in any orientation in the signal head • Industry’s lowest power for all colors • Meets or exceeds intensity, color and uniformity specification • Temperature compensated power supplies for longer LED life • Uniform appearance • Transient suppression exceeds ITE and NEMA specifications (Up to 6KV ring wave) • Manufactured with anti-capillary wires • Conformal coated power supply • Secondary lens treatment for abrasion resistance • ITE products are Intertek/ETL certified and listed on ETL certification program website • All units operate at 80-135VAC RMS, 60±3Hz Part Number 432-1314-001XOD 432-1374-001XOD 431-3334-901XOD 431-3374-901XOD 432-2324-001XOD 432-2374-001XOD 432-1314-001 431-3334-001 432-2374-001 Color Lens Type Typical Wattage at 25oC Dominant Wavelength (nm) Peak Minimum Maintained Luminous Intensity (cd) Compliance CEC Approved Red Red Yellow Yellow Green Green Red Yellow Green Tinted Clear Tinted Clear Tinted Clear Tinted Tinted Clear 6 6 6 6 6 6 6 8 7 628 628 590 590 500 500 628 590 500 56.8 56.8 141.6 141.6 73.9 73.9 5,500 cd/m2 11,000 cd/m2 11,000 cd/m2 ITE, Omnidirectional ITE, Omnidirectional ITE, Omnidirectional ITE, Omnidirectional ITE, Omnidirectional ITE, Omnidirectional Caltrans Caltrans Caltrans • • • • • • • • • www.dialight.com ITE and Caltrans Approved Uniform Appearance LED Traffic Signal Modules • Industry’s lowest power for all colors • Meets or exceeds intensity, color and uniformity specification • Temperature compensated power supplies for longer LED life • Uniform appearance • Expanded view radiation pattern suitable for span wire and steep grade applications • Transient suppression exceeds ITE and NEMA specifications (Up to 6KV ring wave) • Manufactured with anti-capillary wires • Conformal coated power supply • Secondary lens treatment for abrasion resistance • Patent No. 7,281,818 and other patents pending • ITE products are Intertek/ETL certified and listed on ETL certification program website • All units operate at 80-135VAC RMS, 60±3Hz Part Number 433-1110-003XL 433-1170-003XL 433-3130-901XL 433-3170-901XL 433-2120-001XL 433-2170-001XL 433-1110-003 433-3130-001 433-3170-001 433-2120-001 433-2170-001 433-1210-003XL 433-1270-003XL 433-3230-901XL 433-3270-901XL 433-2220-001XL 433-2270-001XL 433-1210-003 433-3230-001 433-3270-001 433-2220-001 433-2270-001 Color Lens Type Dominant Wavelength (nm) Typical Wattage at 25°C Peak Minimum Maintained Luminous Intensity (cd) Compliance CEC Approved Size (in) Red Red Yellow Yellow Green Green Red Yellow Yellow Green Green Red Red Yellow Yellow Green Green Red Yellow Yellow Green Green Tinted Clear Tinted Clear Tinted Clear Tinted Tinted Clear Tinted Clear Tinted Clear Tinted Clear Tinted Clear Tinted Tinted Clear Tinted Clear 625 625 590 590 500 500 625 590 590 500 500 625 625 590 590 500 500 625 590 590 500 500 6 6 7 7 8 8 6 9 9 7 7 6 6 12 12 7 7 6 12 12 9 9 165 165 410 410 215 215 133 267 267 267 267 365 365 910 910 475 475 339 678 678 678 678 ITE ITE ITE ITE ITE ITE Caltrans Caltrans Caltrans Caltrans Caltrans ITE ITE ITE ITE ITE ITE Caltrans Caltrans Caltrans Caltrans Caltrans • • • • • • • • • • • • • • • • • • • • • • 8 8 8 8 8 8 8 8 8 8 8 12 12 12 12 12 12 12 12 12 12 12 Caltrans Approved Programmable Visibility LED Signal Modules • Direct replacement for incandescent lamps in Programmable Visibility (PV) Signals • Compatible with McCain and 3M signal heads • 90% reduction in power vs. incandescent lamps • Sealed lamp is moisture and dust resistant • Fuse and transient suppressor incorporated for line and load protection • Conformal coated power supply • All units operate at 80 - 135VAC RMS, 60 ± 3Hz Part Number Color Lens Type Dominant Wavelength (nm) Typical Wattage at 25°C Peak Minimum Maintained Luminous Intensity Compliance CEC Approved P46-3R33-003 P46-3Y33-003 P46-3B33-003 Red Yellow Green Clear Clear Clear 625 590 500 10 17 8 314 cd/m2 314 cd/m2 314 cd/m2 Caltrans Caltrans Caltrans • • • www.dialight.com ITE and CalTrans Uniform Appearance Hand and Person Pedestrian Signals • Meets / exceeds ITE uniformity ratio of not more than 1 to 5 between the max and min luminance values as measured in (.5”) dia spots • Manufactured with anti-capillary wires • Conformal coated power supply • Fuse and transient suppressor incorporated for superior line and load protection • Independent dedicated power supplies for added safety and reliability • ITE products are Intertek/ETL certified and listed on ETL certification program website • Transient suppression exceeds ITE and NEMA specifications (Up to 6KV ring wave) • All units operate at 80-135VAC RMS, 60±3Hz Part Number Typical Wattage @ 25ºC Min. Luminance (cd/m2) Size Description Compliance Hand Person Hand Person 430-6450-001X 16 x 18 Side-by-side Hand and Person 8 7 1,400 2,200 ITE 430-6472-001X 16 x 18 Overlay Hand and Person 8 6 1,400 2,200 ITE 430-5770-001X 12 x 12 Hand only 8 N/A 1,400 N/A ITE 430-7771-001X 12 x 12 Person only N/A 7 N/A 2,200 ITE 430-6772-001X 12 x 12 Overlay Hand and Person 8 6 1,400 2,200 ITE 430-5570-001X 9x9 Hand only 6 N/A 1,400 N/A ITE 430-7570-001X 9x9 Person only N/A 6 N/A 2,200 ITE 430-6450-001XC 16 x 18 Caltrans Side-by-Side 9 7 3,750 5,300 Caltrans 430-6473-0011 16 x 18 Caltrans Side-by-Side 8 7 3,750 5,300 Caltrans CEC Approved • • • • • • • • • 1 430-6473-001is a pixilated product Uniform Appearance Countdown Pedestrian Signals • MUTCD compliant for countdown applications • Full preemption compatibility • Up to 8 units can be connected in parallel without affecting the monitoring of the Hand/Person • Manufactured with anti-capillary wires • Three (3) Independent dedicated power supplies for added safety and reliability • ITE products are Intertek/ETL certified and listed on ETL certification program website • Conformal coated power supply • Improved optical design to provide superior uniform appearance of the icons • Transient suppression exceeds ITE and NEMA specifications (Up to 6KV ring wave) • All units operate at 80-135VAC RMS, 60±3Hz Part Number Housing Size 430-6479-001X Typical Wattage @ 25ºC2 Symbol Color Countdown Hand Person Countdown Hand 16 x 18 Portland Orange Portland Orange Lunar White 7 8 8 430-6479-001XC 16 x 18 Portland Orange Portland Orange Lunar White 9 10 9 Min. Luminance (cd/m2) Person Countdown Compliance CEC Approved Hand Person 1,400 1,400 2,200 ITE • 3,750 3,750 5,300 Caltrans • 2 countdown power is with the digits 88 displayed Dialight reserves the right to make changes at any time in order to supply the best product possible. The most current version of this document will always be available at: www.dialight.com/Assets/Brochures_And_Catalogs/Signaling/CEC_Brochure.pdf CEC_Brochure_A www.dialight.com