TI TAS1020PFB

TAS1020
USB Streaming Controller
Data Manual
February 2001
DAV Digital Audio - Digital Speakers
SLAS263A
IMPORTANT NOTICE
Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue
any product or service without notice, and advise customers to obtain the latest version of relevant information
to verify, before placing orders, that information being relied on is current and complete. All products are sold
subject to the terms and conditions of sale supplied at the time of order acknowledgment, including those
pertaining to warranty, patent infringement, and limitation of liability.
TI warrants performance of its products to the specifications applicable at the time of sale in accordance with
TI’s standard warranty. Testing and other quality control techniques are utilized to the extent TI deems necessary
to support this warranty. Specific testing of all parameters of each device is not necessarily performed, except
those mandated by government requirements.
Customers are responsible for their applications using TI components.
In order to minimize risks associated with the customer’s applications, adequate design and operating
safeguards must be provided by the customer to minimize inherent or procedural hazards.
TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent
that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other
intellectual property right of TI covering or relating to any combination, machine, or process in which such
products or services might be or are used. TI’s publication of information regarding any third party’s products
or services does not constitute TI’s approval, license, warranty or endorsement thereof.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations and notices. Representation
or reproduction of this information with alteration voids all warranties provided for an associated TI product or
service, is an unfair and deceptive business practice, and TI is not responsible nor liable for any such use.
Resale of TI’s products or services with statements different from or beyond the parameters stated by TI for
that product or service voids all express and any implied warranties for the associated TI product or service,
is an unfair and deceptive business practice, and TI is not responsible nor liable for any such use.
Also see: Standard Terms and Conditions of Sale for Semiconductor Products. www.ti.com/sc/docs/stdterms.htm
Mailing Address:
Texas Instruments
Post Office Box 655303
Dallas, Texas 75265
Copyright  2001, Texas Instruments Incorporated
Contents
Section
1
2
Title
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.2
Functional Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3
Terminal Assignments – Normal Mode . . . . . . . . . . . . . . . . . . . . . . . . .
1.4
Terminal Assignments – External MCU Mode . . . . . . . . . . . . . . . . . . .
1.5
Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.6
Terminal Functions – Normal Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.7
Terminal Functions – External MCU Mode . . . . . . . . . . . . . . . . . . . . . .
1.8
Device Operation Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.9
Terminal Assignments for Codec Port Interface Modes . . . . . . . . . . .
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.1
Architectural Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.1.1
Oscillator and PLL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.1.2
Clock Generator and Sequencer Logic . . . . . . . . . . . . . . . .
2.1.3
Adaptive Clock Generator (ACG) . . . . . . . . . . . . . . . . . . . . .
2.1.4
USB Transceiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.1.5
USB Serial Interface Engine (SIE) . . . . . . . . . . . . . . . . . . . .
2.1.6
USB Buffer Manager (UBM) . . . . . . . . . . . . . . . . . . . . . . . . . .
2.1.7
USB Frame Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.1.8
USB Suspend and Resume Logic . . . . . . . . . . . . . . . . . . . . .
2.1.9
MCU Core . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.1.10
MCU Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.1.11
USB End-Point Configuration Blocks and
End-Point Buffer Space . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.1.12
DMA Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.1.13
Codec Port Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.1.14
I2C Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.1.15
General-Purpose IO Ports (GPIO) . . . . . . . . . . . . . . . . . . . .
2.1.16
Interrupt Logic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.1.17
Reset Logic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.2
Device Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.2.1
Clock Generation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.2.2
Device Initialization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.2.3
USB Enumeration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.2.4
USB Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.2.5
USB Suspend and Resume Modes . . . . . . . . . . . . . . . . . . .
2.2.6
Adaptive Clock Generator (ACG) . . . . . . . . . . . . . . . . . . . . .
Page
1–1
1–1
1–3
1–3
1–4
1–4
1–5
1–6
1–7
1–7
2–1
2–1
2–1
2–1
2–1
2–1
2–1
2–2
2–2
2–2
2–2
2–2
2–2
2–2
2–3
2–3
2–3
2–3
2–3
2–3
2–3
2–3
2–5
2–5
2–6
2–6
iii
2.2.7
USB Transfers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–9
2.2.8
Microcontroller Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–17
2.2.9
External MCU Mode Operation . . . . . . . . . . . . . . . . . . . . . . . 2–17
2.2.10
Interrupt Logic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–17
2.2.11
DMA Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–18
2.2.12
Codec Port Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–18
2.2.13
I2C Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–23
3 Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–1
3.1
Absolute Maximum Ratings Over Operating Temperature Ranges . 3–1
3.2
Recommended Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . 3–1
3.3
Electrical Characteristics Over Recommended Operating
Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–1
3.4
Timing Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–2
3.4.1
Clock and Control Signals Over Recommended Operating
Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–2
3.4.2
USB Transceiver Signals Over Recommended Operating
Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–2
3.4.3
Codec Port Interface Signals (AC ’97 Modes), TA = 25°C, DVDD
= 3.3 V, AVDD = 3.3 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–3
3.4.4
Codec Port Interface Signals (I2S Modes) Over
Recommended Operating Conditions . . . . . . . . . . . . . . . . . . 3–4
3.4.5
Codec Port Interface Signals (General-Purpose Mode)
Over Recommended Operating . . . . . . . . . . . . . . . . . . . . . . . 3–4
3.4.6
I2C Interface Signals Over Recommended Operating
Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3–5
4 Application Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
–1
A MCU Memory and Memory Mapped Registers . . . . . . . . . . . . . . . . . . . . . . . A–1
B Mechanical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B–1
iv
List of Illustrations
Figure
Title
2–1 Adaptive Clock Generator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2–2 Connection of the TAS1020 to an AC ’97 Codec . . . . . . . . . . . . . . . . . . . . . .
2–3 Connection of the TAS1020 to Multiple AC ’97 Codecs . . . . . . . . . . . . . . . . .
2–4 Single Byte Write Transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2–5 Multiple Byte Write Transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2–6 Single Byte Read Transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2–7 Multiple Byte Read Transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3–1 External Interrupt Timing Waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3–2 USB Differential Driver Timing Waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3–3 BIT_CLK and SYNC Timing Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3–4 SYNC, SD_IN, and SD_OUT Timing Waveforms . . . . . . . . . . . . . . . . . . . . . .
3–5 I2S Mode Timing Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3–6 General-Purpose Mode Timing Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . .
3–7 SCL and SDA Timing Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3–8 Start and Stop Conditions Timing Waveforms . . . . . . . . . . . . . . . . . . . . . . . . .
3–9 Acknowledge Timing Waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4–1 Typical TAS1020 Device Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Page
2–7
2–20
2–21
2–24
2–24
2–25
2–25
3–2
3–2
3–3
3–3
3–4
3–4
3–5
3–5
3–5
–1
List of Tables
Table
Title
2–1 EEPROM Header . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2–2 ACG Frequency Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2–3 Terminal Assignments for Codec Port Interface AC ’97 10 Mode . . . . . . . .
2–4 Terminal Assignments for Codec Port Interface AC ’97 20 Mode . . . . . . . .
2–5 Terminal Assignments for Codec Port Interface I2S Modes . . . . . . . . . . . . .
2–6 SLOT Assignments for Codec Port Interface I2S Mode 4 . . . . . . . . . . . . . . .
2–7 SLOT Assignments for Codec Port Interface I2S Mode 5 . . . . . . . . . . . . . . .
2–8 Terminal Assignments for Codec Port Interface General-Purpose Mode . .
Page
2–4
2–8
2–19
2–20
2–21
2–22
2–22
2–22
v
vi
1 Introduction
The TAS1020 integrated circuit (IC) is a universal serial bus (USB) peripheral interface device designed specifically
for applications that require isochronous data streaming. Applications include digital speakers, which require the
streaming of digital audio data between the host PC and the speaker system via the USB connection. The TAS1020
device is fully compatible with the USB Specification Version 1.1 and the USB Audio Class Specification.
The TAS1020 uses a standard 8052 microcontroller unit (MCU) core with on-chip memory. The MCU memory
includes 8K bytes of program memory ROM that contains a boot loader program. At initialization, the boot loader
program downloads the application program code to a 6K RAM from either the host PC or a nonvolatile memory on
the printed-circuit board (PCB). The MCU handles all USB control, interrupt and bulk end-point transactions. In
addition, the MCU can handle USB isochronous end-point transactions.
The USB interface includes an integrated transceiver that supports 12 Mb/s (full speed) data transfers. In addition
to the USB control end-point, support is provided for up to seven in end-points and seven out end-points. The USB
end-points are fully configurable by the MCU application code using a set of end-point configuration blocks that reside
in on-chip RAM. All USB data transfer types are supported.
The TAS1020 device also includes a codec port interface (C-Port) that can be configured to support several industry
standard serial interface protocols. These protocols include the audio codec (AC) ’97 Revision 1.X, the audio codec
(AC) ’97 Revision 2.X and several inter-IC sound (I2S) modes.
A direct memory access (DMA) controller with two channels is provided for streaming the USB isochronous data
packets to/from the codec port interface. Each DMA channel can support one USB isochronous end-point.
An on-chip phase lock loop (PLL) and adaptive clock generator (ACG) provide support for the USB synchronization
modes, which include asynchronous, synchronous and adaptive.
Other on-chip MCU peripherals include an inter-IC control (I2C) serial interface, and two 8-bit general-purpose
input/output (GPIO) ports.
The TAS1020 device is implemented in a 3.3-V 0.25 µm CMOS technology.
1.1 Features
•
Universal Serial Bus (USB)
•
USB specification version 1.1 compatible
•
USB audio class specification 1.0 compatible
•
Integrated USB transceiver
•
Supports 12 Mb/s data rate (full speed)
•
Supports suspend/resume and remote wake-up
•
Supports control, interrupt, bulk, and isochronous data transfer types
•
Supports up to a total of seven in end-points and seven out end-points in addition to the control
end-point
•
Data transfer type, data buffer size, single or double buffering is programmable for each end-point
•
On-chip adaptive clock generator (ACG) supports asynchronous, synchronous and adaptive
synchronization modes for isochronous end-points
•
To support synchronization for streaming USB audio data, the ACG can be used to generate the master
clock for the codec
1–1
•
•
•
•
•
1–2
Micro-Controller Unit (MCU)
•
Standard 8052 8-bit core
•
8K bytes of program memory ROM that contains a boot loader program and a library of commonly used
USB functions
•
6016 bytes of program memory RAM which is loaded by the boot loader program
•
256 bytes of internal data memory RAM
•
Two GPIO ports
•
MCU handles all USB control, interrupt, and bulk end-point transfers
DMA Controller
•
Two DMA channels to support streaming USB audio data to/from the codec port interface
•
Each channel can support a single USB isochronous end-point
•
In the I2S mode the device can support DAC/ADCs at different sampling frequencies
•
A circular programmable FIFO used for isochronous audio data streaming
Codec Port Interface
•
Configurable to support AC’97 1.X, AC’97 2.X, AIC or I2S serial interface formats
•
I2S modes can support a combination of one DAC and/or two ADCs
•
Can be configured as a general-purpose serial interface
•
Can support bulk data transfer using DMA for higher throughput
I2C Interface
•
Master only interface
•
Does not support a multimaster bus environment
•
Programmable to 100 kb/s or 400 kb/s data transfer speeds
•
Supports I2C arbitration and wait states to accomodate slow slaves
General Characteristics
•
High performance 48-pin TQFP Package
•
On-chip phase-locked loop (PLL) with internal oscillator is used to generate internal clocks from a 6 MHz
crystal input
•
Reset output available which is asserted for both system and USB reset
•
External MCU mode supports application firmware development
•
8K ROM with boot loader program and commonly used USB functions library
•
3.3 V core and I/O buffers
1.2 Functional Block Diagram
USB Serial
Interface
Engine
USB
UBM
1.5 k × 8
SRAM
CODEC
Interface
DMA
C–Port
SOF
6 MHz
Suspend
/Resume
Logic
OSC
PLL
ACG
Global
Control/Status
Registers
8052 Core
8 K ROM
I2C
Control
6 K RAM
Port–3
I2 C Bus
Port–1
1.3 Terminal Assignments – Normal Mode
CDATI
CSYNC
CRESET
DVDD
CSCHNE
P1.7
P1.6
P1.5
DVSS
P1.4
P1.3
P1.2
PFB PACKAGE (Normal Mode)
(TOP VIEW)
36 35 34 33 32 31 30 29 28 27 26 25
37
24
38
23
39
22
40
21
41
20
42
19
TAS1020
43
18
44
17
45
16
46
15
47
14
48
13
1
2 3 4
5 6 7
8
P1.1
P1.0
NC
DVDD
NC
P3.5
P3.4
P3.3
DVSS
P3.2/XINT
P3.1
P3.0
9 10 11 12
PLLFILO
AVDD
MCLKI
DVSS
PUR
DP
DM
DVDD
MRESET
TEST
EXTEN
RSTO
CSCLK
CDATO
MCLKO1
MCLKO2
RESET
VREN
SDA
SCL
AVSS
XTALO
XTALI
PLLFILI
1–3
1.4 Terminal Assignments – External MCU Mode
CDATI
CSYNC
CRESET
DVDD
CSCHNE
MCUAD7
MCUAD6
MCUAD5
DVSS
MCUAD4
MCUAD3
MCUAD2
PFB PACKAGE (External Mode)
(TOP VIEW)
36 35 34 33 32 31 30 29 28 27 26 25
37
24
38
23
39
22
40
21
41
20
42
19
TAS1020
43
18
44
17
45
16
46
15
47
14
48
13
2 3 4
5 6 7
8
PLLFILO
AVDD
MCLKI
DVSS
PUR
DP
DM
DVDD
1
MCUAD1
MCUAD0
MCURD
DVDD
MCUWR
MCUINTO
MCUALE
MCUA10
DVSS
XINT
MCUA9
MCUA8
9 10 11 12
MRESET
TEST
EXTEN
RSTO
CSCLK
CDATO
MCLKO1
MCLKO2
RESET
VREN
SDA
SCL
AVSS
XTALO
XTALI
PLLFILI
1.5 Ordering Information
T
Texas Instruments
Audio Solutions
Peripheral Device
Package Type
TQFP
48 pins
1–4
PFB
AS
1020
PFB
1.6 Terminal Functions – Normal Mode
TERMINAL
I/O
DESCRIPTION
PIN
TYPE
NO.
AVDD
AVSS
Power
2
Power
45
CSCLK
CMOS
37
I/O
Codec port interface serial clock: CSCLK is the serial clock for the codec port interface used to clock
the CSYNC, CDATO, CDATI, CRESET, AND CSCHNE signals.
CSYNC
CMOS
35
I/O
Codec port interface frame sync: CSYNC is the frame synchronization signal for the codec port
interface.
CDATO
CMOS
38
I/O
Codec port interface serial data out
CDATI
CMOS
36
I/O
Codec port interface serial data in
CRESET
CMOS
34
I/O
Codec port interface reset output
CSCHNE
CMOS
32
I/O
Codec port interface secondary channel enable
DP
CMOS
6
I/O
USB differential pair data signal plus. DP is the positive signal of the bidirectional USB differential
pair used to connect the TAS1020 device to the universal serial bus.
DM
CMOS
7
I/O
USB differential pair data signal minus. DM is the negative signal of the bidirectional USB differential
pair used to connect the TAS1020 device to the universal serial bus.
DVDD
Power
8, 21, 33
3.3-V digital supply voltage
DVSS
Power
4, 16, 28
Digital ground
EXTEN
CMOS
11
I
External MCU mode enable: Input used to enable the device for the external MCU mode
MCLKI
CMOS
3
I
Master clock input. An input that can be used as the master clock for the codec port interface or the
source for MCLKO2.
MCLKO1
CMOS
39
O
Master clock output 1: The output of the ACG that can be used as the master clock for the codec port
interface and the codec.
MCLKO2
CMOS
40
O
Master clock output 2: An output that can be used as the master clock for the codec port interface and
the codec used in I2S modes for receive. This clock signal can also be used as a miscellaneous
clock.
MRESET
CMOS
9
I
Master reset: An active low asynchronous reset for the device that resets all logic to the default state
P1.[0:7]
CMOS
23, 24,
25, 26,
27, 29,
30, 31
I/O
General-purpose I/O port [bits 0 through 1]: A bidirectional 8-bit I/O port with an internal 100 µA
active pullup
P3.[0:6]
CMOS
13, 14,
15, 17,
18, 19
I/O
General-purpose I/O port [bits 0 through 1]: A bidirectional I/O port with an internal 100 µA active
pullup
PLLFILI
CMOS
48
I
PLL loop filter input: Input to on-chip PLL from external filter components
PLLFILO
CMOS
1
O
PLL loop filter output: Output from on-chip PLL to external filter components
PUR
CMOS
5
O
USB data signal plus pullup resistor connect. PUR is used to connect the pullup resistor on the DP
signal to 3.3-V or a 3-state. When the DP signal is connected to 3.3-V the host PC detects the
connection of the TAS1020 device to the universal serial bus.
RESET
CMOS
41
O
General-purpose active-low output which is memory mapped
RSTO
CMOS
12
O
SCL
CMOS
44
O
Reset output: An output that is active while the master reset input or the USB reset is active
I2C interface serial clock
SDA
CMOS
43
I/O
I2C interface serial data
TEST
CMOS
10
I
Test mode enable: Factory test mode
VREN
CMOS
42
O
General-purpose active-low output which is memory mapped
XINT
CMOS
15
I
External interrupt: An active low input used by external circuitry to interrupt the on-chip 8052 MCU
XTALI
CMOS
47
I
Crystal input: Input to the on-chip oscillator from an external 6-MHz crystal
XTALO
CMOS
46
O
Crystal Output: Output from the on-chip oscillator to an external 6-MHz crystal
NAME
NC
3.3-V analog supply voltage
Analog ground
20,22
Not used
1–5
1.7 Terminal Functions – External MCU Mode
TERMINAL
PIN
TYPE
NO.
AVDD
AVSS
Power
2
Power
CSCLK
CMOS
CSYNC
NAME
I/O
DESCRIPTION
–
3.3-V Analog supply voltage
45
–
Analog ground
37
I/O
Codec port interface serial clock: CSCLK is the serial clock for the codec port interface used to
clock the CSYNC, CDATO, CDATI, CRESET AND CSCHNE signals.
CMOS
35
I/O
Codec port interface frame sync: CSYNC is the frame synchronization signal for the codec port
interface.
CDATO
CMOS
38
I/O
Codec port interface serial data output
CDATI
CMOS
36
I/O
Codec port interface serial data input
CRESET
CMOS
34
I/O
Codec port interface reset output
CSCHNE
CMOS
32
I/O
Codec port interface secondary channel enable
DP
CMOS
6
I/O
USB differential pair data signal plus: DP is the positive signal of the bidirectional USB differential
pair used to connect the TAS1020 device to the universal serial bus.
DM
CMOS
7
I/O
USB differential pair data signal minus. DM is the negative signal of the bidirectional USB differential pair used to connect the TAS1020 device to the universal serial bus.
DVDD
Power
8, 21, 33
–
3.3-V Digital supply voltage
DVSS
Power
4, 16, 28
–
Digital ground
EXTEN
CMOS
11
I
External MCU mode enable: Input used to enable the device for the external MCU mode. This signal uses a 3.3 V TTL/LVCMOS input buffer.
MCLKI
CMOS
3
I
Master clock input: An input that can be used as the master clock for the codec port interface or the
source for MCLKO2.
MCLKO1
CMOS
39
O
Master clock output 1: The output of the ACG that can be used as the master clock for the codec
port interface and the codec.
MCLKO2
CMOS
40
O
Master clock output 2: An output that can be used as the master clock for the codec port interface
and the codec. This clock signal can also be used as a miscellaneous clock.
MRESET
CMOS
9
I
Master reset: An active low asynchronous reset for the device that resets all logic to the default
state.
MCUAD
[0:7]
CMOS
23, 24, 25,
26, 27, 29,
30, 31
I/O
MCU multiplexed address/data bit 0: Multiplexed address bit 0/data bit 0 for external MCU access
to the TAS1020 external data memory space.
MCUA
[8:10]
CMOS
13, 14, 17
I/O
MCU address bus: Multiplexed address bus for external MCU access to the TAS1020 external
data memory space.
MCUALE
CMOS
18
I
MCU address latch enable: Address latch enable for external MCU access to the TAS1020 external data memory space.
MCUINTO
CMOS
19
O
MCU interrupt output: Interrupt output to be used for external MCU INTO input signal. All internal
TAS1020 interrupt sources are read together to generate this output signal.
MCUWR
CMOS
20
I
MCU write strobe: Write strobe for external MCU write access to the TAS1020 external data
memory space.
MCURD
CMOS
22
I
MCU read strobe: Read strobe for external MCU read access to the TAS1020 external data
memory space.
PLLFILI
CMOS
48
I
PLL loop filter input: Input to on-chip PLL from external filter components.
PLLFILO
CMOS
1
O
PLL loop filter output: Output to on-chip PLL from external filter components.
PUR
CMOS
5
O
USB Data signals plus pullup resistor connect. PUR is used to connect the pullup resistor on the
DP signal to 3.3V to a 3-state. When the DP signal is connect to a 3.3V, the host PC should detect
the connection of the TAS1020 device to the universal serial bus.
RESET
CMOS
41
O
General-purpose active-low output which is memory mapped
RSTO
CMOS
12
O
SCL
CMOS
44
O
Reset output: An output that is active while the master reset input or the USB reset is active.
I2C interface serial clock
SDA
CMOS
43
I/O
I2C interface serial data input/output
TEST
CMOS
10
I
Test mode enable: Factory text mode
1–6
1.7 Terminal Functions – External MCU Mode (Continued)
TERMINAL
I/O
DESCRIPTION
PIN
TYPE
NO.
VREN
CMOS
42
O
General-purpose active-low output which is memory mapped.
XINT
CMOS
15
I
External interrupt: An active low input used by external circuitry to interrupt the on-chip 8052 MCU.
XTALI
CMOS
47
I
Crystal input: Input to the on-chip oscillator from an external 6-MHz crystal.
XTALO
CMOS
46
O
Crystal output: Output from the on-chip oscillator to an external 6-MHz crystal.
NAME
1.8 Device Operation Modes
The EXTEN and TEST pins define the mode that the TAS1020 is in after reset.
EXTEN
TEST
Normal mode – internal MCU
MODE
0
0
External MCU mode
1
0
Factory test
0
1
Factory test
1
1
1.9 Terminal Assignments for Codec Port Interface Modes
The codec port interface has five modes of operation that support AC97, I2S, and AIC codecs. There is also a
general-purpose mode that is not specific to a serial interface. The mode is programmed by writing to the mode select
field of the codec port interface configuration register 1 (CPTCNF1). The codec port interface terminals CSYNC,
CSCLK, CDATO, CDATI, CRESET, and CSCHNE take on functionality appropriate to the mode programmed as
shown in the following table.
TERMINAL
NO.
GP
Mode 0
NAME
AIC
Mode 1
AC ’97 v1.X
Mode 2
AC ’97 v2.X
Mode 3
I2S
Mode 4
I2S
Mode 5
35
CSYNC
CSYNC
I/O
FS
O
SYNC
O
SYNC
O
LRCK
O
LRCK1
O
37
CSCLK
CSCLK
I/O
SCLK
O
BIT_CLK
I
BIT_CLK
I
SCLK
O
SCLK1
O
38
CDATO
CDATO
O
DOUT
O
SD_OUT
O
SD_OUT
O
SDOUT1
O
SDOUT1
O
36
CDATI
CDATI
I
DIN
I
SD_IN
I
SD_IN1
I
SDIN1
I
SDIN2
I
34
CRESET
CRESET
O
RESET
O
RESET
O
RESET
O
CRESET
O
SCLK2
O
32
CSCHNE
NC
O
FC
O
NC
O
SD_IN2
I
SDIN2
I
LRCK2
O
NOTES: 1. Signal names and I/O direction are with respect to the TAS1020 device. The signal names used for the TAS1020 terminals for the
various codec port interface modes reflect the nomenclature used by the codec devices.
2. NC indicates no connection for the terminal in a particular mode. The TAS1020 device drives the signal as an output for these cases.
3. The CSYNC and CSCLK signals can be programmed as either an input or an output in the general-purpose mode.
1–7
1–8
2 Description
2.1 Architectural Overview
2.1.1
Oscillator and PLL
Using an external 6-MHz crystal, the TAS1020 derives the fundamental 48-MHz internal clock signal using an on-chip
oscillator and PLL. Using the PLL output, the other required clock signals are generated by the clock generator and
adaptive clock generator.
2.1.2
Clock Generator and Sequencer Logic
Utilizing the 48-MHz input from the PLL, the clock generator logic generates all internal clock signals, except for the
codec port interface master clock (MCLK) and serial clock (CSCLK) signals. The TAS1020 internal clocks include
the 48-MHz clock, a 24-MHz clock, a 12-MHz clock and a USB clock. The USB clock also has a frequency of 12-MHz.
The USB clock is the same as the 12-MHz clock when the TAS1020 is transmitting data and is derived from the data
when the TAS1020 is receiving data. To derive the USB clock when receiving USB data, the TAS1020 utilizes an
internal digital PLL (DPLL) that uses the 48-MHz clock.
The sequencer logic controls the access to the SRAM used for the USB end-point configuration blocks and the USB
end-point buffer space. The SRAM can be accessed by the MCU, USB buffer manager (UBM), or DMA channels.
The sequencer controls the access to the memory using a round-robin fixed priority arbitration scheme. This means
that the sequencer logic generates grant signals for the MCU, UBM, and DMA channels at a predetermined fixed
frequency.
2.1.3
Adaptive Clock Generator (ACG)
The adaptive clock generator is used to generate a master clock output signal (MCLKO) to be used by the codec port
interface and the codec device. To synchronize data sent to or received from the codec to the USB frame rate, the
MCLKO signal generated by the adaptive clock generator must be used. The synchronization of the MCLKO signal
to the USB frame rate is controlled by the MCU by programming the adaptive clock generator frequency value. The
MCLKO frequency is monitored by the MCU and updated as required. For asynchronous operation, an external
source can be used to generate a master clock input signal (MCLKI) to be used by the codec port interface. In this
scenario, the codec device also uses the same master clock signal (MCLKI).
2.1.4
USB Transceiver
The TAS1020 provides an integrated transceiver for the USB port. The transceiver includes a differential output driver,
a differential input receiver, and two single ended input buffers. The transceiver connects to the USB DP and DM
signal terminals.
2.1.5
USB Serial Interface Engine (SIE)
The serial interface engine logic manages the USB packet protocol requirements for the packets being received and
transmitted on the USB by the TAS1020 device. For packets being received, the SIE decodes the packet identifier
field (PID) to determine the type of packet being received and to ensure the PID is valid. For token packets and data
packets being received, the SIE calculates the packet cycle redundancy check (CRC) and compares the value to the
CRC contained in the packet to verify that the packet was not corrupted during transmission. For token packets and
data packets being transmitted, the SIE generates the CRC that is transmitted with the packet. For packets being
transmitted, the SIE also generates the synchronization field (SYNC) that is an eight bit filed at the beginning of each
packet. In addition, the SIE generates the correct PID for all packets being transmitted. Another major function of the
SIE is the overall serial-to-parallel conversion of the data packets being received and the parallel-to-serial conversion
of the data packets being transmitted.
2–1
2.1.6
USB Buffer Manager (UBM)
The USB buffer manager provides the control logic that interfaces the SIE to the USB end-point buffers. One of the
major functions of the UBM is to decode the USB function address to determine if the host PC is addressing the
TAS1020 device USB peripheral function. In addition, the end-point address field and direction signal are decoded
to determine which particular USB end-point is being addressed. Based on the direction of the USB transaction and
the end-point number, the UBM will either write or read the data packet to/from the appropriate USB end-point data
buffer.
2.1.7
USB Frame Timer
The USB frame timer logic receives the start of frame (SOF) packet from the host PC each USB frame. Each frame,
the logic stores the 11-bit frame number value from the SOF packet in a register and asserts the internal SOF signal.
The frame number register can be read by the MCU and the value can be used as a time stamp. For USB frames
in which the SOF packet is corrupted or not received, the frame timer logic will generate a pseudo start of frame
(PSOF) signal and increment the frame number register.
2.1.8
USB Suspend and Resume Logic
The USB suspend and resume logic detects suspend and resume conditions on the USB. This logic also provides
the internal signals used to control the TAS1020 device when these conditions occur. The capability to resume
operation from a suspend condition with a locally generated remote wake-up event is also provided.
2.1.9
MCU Core
The TAS1020 uses an 8-bit microcontroller core that is based on the industry standard 8052. The MCU is software
compatible with the 8052, 8032, 80C52, 80C53, and 87C52 MCUs. The 8052 MCU is the processing core of the
TAS1020 and handles all USB control, interrupt and bulk end-point transfers. In addition, the MCU can also be the
source or sink for USB isochronous end-point transfers.
2.1.10 MCU Memory
In accordance with the industry standard 8052, the TAS1020 MCU memory is organized into program memory,
external data memory and internal data memory. A boot ROM program is used to download the application code to
a 6K byte RAM that is mapped to the program memory space. The external data memory includes the USB end-point
configuration blocks, USB data buffers, and memory mapped registers. The total external data memory space
available is 1.5K bytes. A total of 256 bytes are provided for the internal data memory.
2.1.11 USB End-Point Configuration Blocks and End-Point Buffer Space
The USB end-point configuration blocks are used by the MCU to configure and operate the required USB end-points
for a particular application. In addition to the control end-point, the TAS1020 supports a total of seven in end-points
and seven out end-points. A set of six bytes is provided for each end-point to specify the end-point type, buffer
address, buffer size, and data packet byte count.
The USB end-point buffer space provided is a total of 1440 bytes. The space is totally configurable by the MCU for
a particular application. Therefore, the MCU can configure each buffer based on the total number of end-points to
be used, the maximum packet size to be used for each end-point, and the selection of single or double buffering.
2.1.12 DMA Controller
Two DMA channels are provided to support the streaming of data for USB isochronous and bulk end-points. Each
DMA channel can support one USB isochronous and bulk end-points, either in or out. The DMA channels are used
to stream data between the USB end-point data buffers and the codec port interface. The USB end-point number and
direction can be programmed for each DMA channel. Also, the codec port interface time slots to be serviced by each
DMA channel can be programmed.
2–2
2.1.13 Codec Port Interface
The TAS1020 provides a configurable full duplex bidirectional serial interface that can be used to connect to a codec
or another device for streaming USB isochronous data. The interface can be configured to support several different
industry standard protocols, including AC ’97 1.X, AC ’97 2.X, AIC, and I2S. The TAS1020 also has a general-purpose
mode to support other protocols.
2.1.14 I2C Interface
The I2C interface logic provides a two-wire serial interface that the 8052 MCU can use to access other ICs. The
TAS1020 is an I2C master device only and supports single byte or multiple byte read and write operations. The
interface can be programmed to operate at either 100 kbps or 400 kbps. In addition, the protocol supports 8-bit or
16-bit addressing for accessing the I2C slave device memory locations. The TAS1020 supports I2C wait states. This
means slaves can assert wait state on the I2C bus by pulling the SCL low.
2.1.15 General-Purpose IO Ports (GPIO)
The TAS1020 provides two general-purpose IO ports that are controlled by the internal 8052 MCU. The two ports
are port 1 and port 3. Port 3 bit location 2 is used as the external interrupt (XINT) input to the TAS1020.
Each bit of both ports can be independently used as either an input or output. Hence each port bit consists of an output
buffer, an input buffer, and a pullup resistor. The pullup resistors for each GPIO port can be disabled using the PUDIS
bits in the global control register. Any port 3 pin can be used to wake up the host PC in low-power suspend mode.
2.1.16 Interrupt Logic
The interrupt logic monitors the various conditions that can cause an interrupt and asserts the interrupt 0 (INTO) input
to the 8052 MCU accordingly. All of the TAS1020 internal interrupt sources and the external interrupt (XINT) input
are OR’ed together to generate the INT0 signal. An interrupt vector register is used by the MCU to identify the interrupt
source.
2.1.17 Reset Logic
An external master reset (MRESET) input signal that is asynchronous to the internal clocks is used to reset the
TAS1020 logic. In addition to the master reset, the TAS1020 logic can be reset with the USB reset from the host PC.
The TAS1020 also provides a reset output (RSTO) signal that can be used by external devices. This signal is asserted
when either a master reset or USB reset occurs.
2.2 Device Operation
The operation of the TAS1020 is explained in the following sections. For additional information on USB, refer to the
Universal Serial Bus Specification version 1.1.
2.2.1
Clock Generation
The TAS1020 requires an external 6-MHz crystal and PLL loop filter components connected as shown in Figure 4-1
to derive all the clocks needed for both USB and codec operation. Using the low frequency 6-MHz crystal and
generating the required higher frequency clocks internal to the IC is a major advantage regarding EMI.
2.2.2
Device Initialization
After a power-on reset is applied to the TAS1020 device, the 8052 MCU executes a boot loader program from the
8K byte boot ROM mapped to the program memory space. During device initialization, the boot loader program
downloads the application program code from an external EEPROM through the I2C interface. This requires that a
binary image of the application code be written to the 6K byte code RAM in the TAS1020 device.
2–3
All memory mapped registers are initialized to a default value as defined in Appendix A, MCU Memory and MemoryMapped Registers. The TAS1020 device powers up with a default function address of zero and disconnected from
the USB.
2.2.2.1 Boot Load from EEPROM
Loading the application code from an external serial EEPROM requires a preprogrammed memory device containing
an informative header and the application code. While the application code is being downloaded, the TAS1020
remains disconnected from the USB. When the code download is complete, execution of the application code
connects the TAS1020 to the USB. In this situation, the TAS1020 enumerates using the vendor ID and product ID
contained in the application code.
2.2.2.2 EEPROM Header
For both application code and USB device information stored in a EEPROM device, a common header format is used
that precedes the data payload. Table 2-1 shows the format and information contained in the header.
Table 2–1. EEPROM Header
OFFSET
TYPE
SIZE
VALUE
0
headerChksum
1
Check sum of the header by adding the header, excluding the header cheksum, in bytes.
1
HeaderSize
1
Size of the header including strings if applied
2
Signature
2
Signature: 0x1234
4
VenderID
2
USB Vendor ID
6
ProductID
2
USB Vendor ID
8
ProductVersion
1
Product version
9
FirmwareVersion
1
Firmware version
10
UsbAttributes
1
USB attributes:
Bit 0: If set to 1, the header includes all three strings: language, manufacture, and product strings, if set
to 0, the header does not include any string.
Bit 2: If set to 1, the device can be self powered, if set to 0, it is not self powered.
Bit 3: If set to 1, the device can be bus powered, if set to 0, it is not be bus powered.
Bit 1 and 4 ... 7: Not used.
11
MaxPower
1
Maximum power the device needs in units of 2 mA.
12
Attribute
1
13
WPageSize
1
Device attributes:
Bit 3: If set to 1, the devices EEPROM support 400 kHz, if set to 0, it can not support 400 MHz.
Bit 0: If set to 1, the CPU speed runs at 24 MHz, if set to 0, the CPU speed runs at 12 MHz.
Bit 1, 2 and 4 ... 7: Not used.
Maximum I2C write page size
14
DataType
1
15
RpageSize
1
16
This value defines if the device is application EEPROM, device EEPROM.
0x01: Application EEPROM
0x02: Device EEPROM
Other values are invalid.
Maximum I2C read page size. If the value is zero, the whole payLoadSize is read in one I2C read
setup.
payLoadSize
2
Size of the application, if using EEPROM as an application EEPROM, otherwise the value is 0.
0xxx
Language string
4
Language string in standard USB string format if applied.
0xxx
Manufacture string
...
Manufacture string in standard USB string format if applied.
0xxx
Product string
...
Product string in standard USB string format if applied.
0xxx
Application Code
...
Application code if applied
The signature field is used for the detection of a EEPROM device connected to the TAS1020. The header size field
supports future updates of the header. Data begins right after the header. The version field identifies the header
version. The EEPROM type field identifies the specific EEPROM device being used. The data type field describes
the nature of data stored in the EEPROM (application code or USB device information). The data size field holds the
2–4
length of the data payload starting from the end of the header. The check sum field contains the check sum for the
data payload portion of the EEPROM.
2.2.2.3 EEPROM Data Type
The two types of data that are stored in the EEPROM are application code and USB device information.
2.2.2.3.1 Application Code
Application firmware is stored as a binary image of the code. The binary image is mapped to the MCU program
memory space starting at address zero and is stored in the EEPROM as a continuous linear block starting after the
header information. A utility program is available to convert a file in Intel hexadecimal format to a binary image data
file and appends it to the header.
2.2.2.4 EEPROM Device Type
The TAS1020 boot loader program supports several different types of serial EEPROM devices. The boot loader
program automatically identifies the EEPROM type from the header information and uses the correct serial interface
protocol accordingly. The boot loader program uses an I2C slave device address of A0h for the serial EEPROM
device.
These EEPROM devices require an I2C device address in addition to a two byte data word address. These devices
require the full 7-bit I2C device address. Depending on the memory size of the EEPROM device being used, the most
significant three or four bits of the two byte data word address are don’t care bits.
2.2.3
USB Enumeration
USB enumeration is accomplished by interaction between the host PC software and the TAS1020 code. After
power-on reset the boot loader code first reads the information from the EEPROM, then runs the application code.
The application code connects the TAS1020 to the USB. During the enumeration, the application code identifies the
device as an application specific device and the host loads the appropriate host driver(s). The boot loader and
application code both use the CONT, SDW and FRSTE bits to control the enumeration process. The function connect
(CONT) bit is set to a 1 by the MCU to connect the TAS1020 device to the USB. When this bit is set to a 1, the USB
data plus pullup resistor (PUR) output signal is enabled, which connects the pullup on the PCB to the TAS1020 3.3-V
digital supply voltage. When this bit is cleared to a 0, the PUR output is in the 3-state mode. This bit is not affected
by a USB reset. The shadow the boot ROM (SDW) bit is set to a 1 by the MCU to switch the MCU memory configuration
from boot loader mode to normal operating mode. The function reset enable (FRSTE) bit is set to a 1 by the MCU
to enable the USB reset to reset all internal logic including the MCU. However, the shadow the ROM (SDW) and the
USB function connect (CONT) bits will not be reset. When this bit is set, the reset output (RSTO) signal from the
TAS1020 device is also active when a USB reset occurs. This bit is not affected by USB reset.
2.2.4
USB Reset
The TAS1020 can detect a USB reset condition. When the reset occurs, the TAS1020 responds by setting the function
reset (RSTR) bit in the USB status register (USBSTA). If the corresponding function reset bit in the USB interrupt mask
register is set, an MCU interrupt will be generated and the USB function reset (0x17) vector will appear in the interrupt
vector register (VECINT).
The function reset enable bit (FRSTE) in the USB control register (USBCTL) is used to control the extent to which
the internal logic is reset. The function reset enable bit is set to a 1 by the MCU to enable the USB reset to reset all
internal logic including the MCU. However, the shadow the ROM (SDW) and the USB function connect (CONT) bits
will not be reset. When the FRSTE bit is set, the reset output (RSTO) signal from the device also is active when a
USB reset occurs. This bit is not affected by USB reset.
2–5
2.2.5
USB Suspend and Resume Modes
A suspend condition is defined as a constant idle state on the bus for more than 3 ms. A USB device must actually
be in the suspend state no more than 10 ms after the suspend condition is detected. There are two ways for the
TAS1020 device to exit the suspend mode: 1) detection of USB resume signaling and 2) detection of a local remote
wake-up event.
2.2.5.1 USB Suspend Mode
When a suspend condition is detected on the USB, the suspend/resume logic sets the function suspend request bit
(SUSR) in the USB status register. As a result, the function suspend request interrupt (SUSR) is generated. To enter
the low-power suspend state and disable all TAS1020 device clocks, the MCU firmware must set the idle mode bit
(IDL), which is bit 0 in the MCU power control (PCON) register. Note that the IDL bit must be set in the main ( ) routine,
not in the suspend interrupt service routine. The instruction that sets the IDL bit is the last instruction executed before
the MCU goes to idle mode. In idle mode, the MCU status is preserved. Note that the low power suspend state is a
state in which the TAS1020 clocks are disabled and the IC will consume the least amount of power possible.
2.2.5.2 USB Resume Mode
When the TAS1020 is in a suspend state, any non-idle signaling on the USB is detected by the suspend/resume logic
and device operation resumes. When the resume signal is detected, the TAS1020 clocks are enabled, the function
resume request bit (RESR) will be set, and the function resume request interrupt (RESR) will be generated. The
function resume request interrupt to the MCU automatically clears the idle mode bit in the PCON register. As a result,
MCU operation resumes servicing the new interrupt. After the RETI from the ISR, the next instruction to be executed
is the one following the instruction that set the IDL bit. Note that if the low-power suspend state was not entered by
setting the IDL bit, the clocks are already enabled, and the IDL bit is already cleared.
2.2.5.3 USB Remote Wake-Up Mode
The TAS1020 device has the capability to remotely wake-up the USB by generating resume signaling upstream. Note
that this feature must be enabled by the host software with the SET_FEATURE DEVICE_REMOTE_WAKEUP
request. The remote wake-up resume signaling must not be generated until the suspend state has been active for
at least 5 ms. In addition, the remote wake-up resume signaling must be generated for at least 1ms but for no more
than 15 ms. When the TAS1020 is in the low power suspend state, asserting the external interrupt input (XINT) to
the device enables the clocks and generates the XINT interrupt. The XINT interrupt to the MCU automatically clears
the idle mode bit in the PCON register. As a result, MCU operation resumes servicing the new interrupt. After the RETI
from the ISR, the next instruction to be executed is the one following the instruction that set the IDL bit. Note that if
the low-power suspend state was not entered by setting the IDL bit, the clocks is already enabled and the IDL bit is
already cleared. When the firmware sets the remote wake-up request bit (RWUP) in the USB control register, the
suspend/resume logic generates the resume signaling upstream on the USB.
The remote wakeup in the TAS1020 is set to level triggered, a default value. The bit TCON.2 in the MCU determines
whether it is an edge triggered or a level triggered. 1 indicates edge triggered, 0 indicates level triggered. The default
value is 0. In order to use the remote wakeup function, RWUP bit has to be set in the USBCTL register. If XINT pin
is used for remote wakeup, XINTEN bit has to be set in the GLOBCTL register. If one of the port 3 pins is used for
remote wakeup, the bit associated with the pin has to be unmasked in the P3MSK register.
2.2.6
Adaptive Clock Generator (ACG)
The adaptive clock generator is used to generate two programmable master clock output signals (MCLKO and
MCLKO2) that can be used by the codec port interface and the codec device. The ACG can be used to generate the
master clock for the codec for USB asynchronous, synchronous, and adaptive modes of operation. However, for the
USB asynchronous mode of operation, an external clock can be used to drive the MCLKI signal of the TAS1020. In
this scenario, the MCLKI signal is used as the clock source for the codec port interface instead of the clock output
from the ACG.
2–6
A block diagram of the adaptive clock generator is shown in Figure 2–1. The frequency synthesizer circuit generates
a programmable clock with a frequency range of 12 – 25 MHz. The output of the frequency synthesizer feeds the
divide-by-M circuit, which can be programmed to divide by 1 to 16. As a result, the frequency range of the MCLKO
signal is 750 kHz to 25 MHz. The duty cycle of the MCLKO signal is 50% for all programmable MCLKO frequencies.
As shown in Figure 2–1, the C-Port serial clock (CSCLK) is derived by setting the divide by B value in codec interface
configuration register CPTNCF4 [2:0] and the C-Port serial clock2 (CSCLK2) is derived by setting the divide by B
value in codec port receive interface register 4 CPTRXCNF4 [2:0].
SOF
ACGCAPH
ACGCAPL
16-Bit Counter
PSOF
ACG1DCTL[7:4]
4
ACGCTL[5]
ACGCTL[4]
ACGCTL[6]
6 MHz
Oscillator
PLL
Divide
by M1
Frequency 1
Synthesizer
MCLK0
Divide by B
CPTCNF4 [2:0]
ACG2DCTL[7:4]
4
ACGCTL[1]
ACGCTL[0]
ACGCTL[7]
Divide
by M2
Frequency 2
Synthesizer
CSCLK
MCLK02
ACG1DCTL[2:0]
Divide by B
CPTRXCNF4 [2:0]
3
CSCLK2
Divide
by I
MCLKI
Figure 2–1. Adaptive Clock Generator
The ACG is controlled by the following registers. Refer to section A.5.3 for details.
FUNCTIONAL REGISTER
24-bit frequency register #1
ACTUAL BYTE-WIDE REGISTERS
ACG1FRQ2
16-bit capture register
ACG1FRQ1
ACG1FRQ0
ACGCAPH
ACGCAPL
8-bit synthesizer 1 divider control register
ACG1DCTL
8-bit ACG control register
24-bit frequency register #2
ACGCTL
ACG2FRQ2
ACG2FRQ1
8-bit synthesizer 2 divider control register
ACG2FRQ0
ACG2DCTL
The main functional modules of the ACG are described in the following sections.
2.2.6.1 Programmable Frequency Synthesizer
The 24-bit ACG frequency register value is used to program the frequency synthesizer. This programming results
in high resolution to accurately select the desired codec master clock frequency. The value of the frequency register
may be updated by the MCU while the ACG is running. In audio applications, the firmware can adjust the frequency
value by ±LSB or more to lock onto the USB start-of-frame (SOF) signal and achieve a synchronous mode of
operation. The 24-bit frequency register value is updated and used by the frequency synthesizer only when MCU
writes to the ACGFRQ0 register.
Depending on the application, a smaller number of bits for controlling the synthesizer frequency can be chosen. The
frequency resolution also depends on the actual frequency being used. In general, the frequency resolution is less
for higher frequencies and more for lower frequencies. This is due to the fact that the 208 ps frequency resolution
becomes more significant compared to the period at higher frequencies than at lower frequencies. The resolution
increases with the number of bits used to represent the frequency as the quantization error reduces because more
bits are used to represent a fractional number.
2–7
The clock frequency of the MCLKO output signal is calculated by using the formula:
For N > 24 and N < 50, MCLKO frequency = (25/N) × 192/8 MHz
For N = 50, MCLKO frequency = 96/8 MHz
Where N is the value in the 24-bit frequency register (ACGFRQ). The value of N can range from 24 to 50. The six
most significant bits of the 24-bit frequency register are used to represent the integer portion of N, and the remaining
18 bits of the frequency register are used to represent the fractional portion of N. An example is shown below.
Example Frequency Register Calculation
Suppose the desired MCLKO frequency is 24.576 MHz. Using the above formula, N = 24.4140625 decimal. To
determine the binary value to be written to the ACGFRQ register, separately convert the integer value (24) to 6-bit
binary and the fractional value (4140625) to 18-bit binary. As a result, the 24-bit binary value is
011000.011010100000000000.
The corresponding values to program into the ACGFRQ registers are:
ACGFRQ2 = 01100001b = 61h
ACGFRQ1 = 10101000b = A8h
ACGFRQ0 = 00000000b = 00h
Keep in mind that writing to the ACGFRQ0 register loads the frequency synthesizer with the new 24-bit value.
Example Frequency Resolution Calculation
To illustrate the frequency resolution capabilities of the ACG, the next possible higher and lower frequencies for
MCLKO can be calculated.
To get the next possible higher frequency of MCLKO equal to 24.57600384 MHz, increase the value of N by 1 LSB.
Thus, N = 011000.011010100000000001 binary.
To get the next possible lower frequency of MCLKO equal to 24.57599600 MHz, decrease the value of N by 1 LSB.
Thus, N = 011000.011010011111111111 binary.
For this example with a nominal MCLKO frequency of 24.576 MHz, the frequency resolution is approximately 4 Hz.
Table 2-2 lists typically used frequencies and corresponding ACG frequency registers.
Table 2–2. ACG Frequency Registers
SYNTHESIZED CLOCK OUTPUT
ACG1FRQ2/ACG2FRQ2
ACG1FRQ1/ACG2FRQ1
ACG1FRQ0/ACG2FRQ0
25 MHz
0x60
0
0
24.576 MHz
0x61
0×A8
0x0F
22.579 MHz
0x6A
0x4B
0x20
18.432 MHz
0x82
0x35
0x55
16.934 MHz
0x8D
0xBA
0x09
16.384 MHz
0x92
0x7C
0x00
12.288 MHz
0xC3
0x50
0x00
12 MHz
0xC8
0
0
2.2.6.2 Capture Counter and Register
The capture counter and register circuit consists of a 16-bit free running counter which runs at the capture clock
frequency. The capture clock source can be selected by using the MCLKCP bit in the ACGCTL register to select either
the MCLKO or MCLKO2 signal. With each USB start-of-frame (SOF) signal or pseudo-start-of-frame (PSOF) signal,
the capture counter value is stored into the 16-bit capture register. This value is valid until the next SOF or PSOF signal
occurs (~1 ms). The MCU can read the 16-bit capture register value by reading the ACGCAPH and ACGCAPL
registers.
2–8
2.2.7
USB Transfers
The TAS1020 device supports all the USB data transfer types: control, bulk, interrupt, and isochronous. In accordance
with the USB specification, endpoint zero is reserved for the control endpoint and is bidirectional. In addition to the
control endpoint, the TAS1020 is capable of supporting up to 7 in endpoints and 7 out endpoints. These additional
endpoints can be configured as bulk, interrupt, or isochronous endpoints. The MCU handles all control, bulk, and
interrupt endpoint transactions. In addition, the MCU can handle isochronous endpoint transactions, such as a rate
feedback endpoint to the host PC. However, for streaming isochronous data between the host PC and the codec
interface port, the DMA channels are provided.
2.2.7.1 Control Transfers
Control transfers are used for configuration, command, and status communication between the host PC and the
TAS1020 device. Control transfers to the TAS1020 device use in endpoint 0 and out endpoint 0. The three types of
control transfers are control write, control write with no data stage, and control read. Note that the control endpoint
must be initialized before connecting the TAS1020 device to the USB.
2.2.7.1.1 Control Write Transfer (Out Transfer)
The host PC uses a control write transfer to write data to the USB function. A control write transfer consists of a setup
stage transaction, at least one out data stage transaction, and an in-status stage transaction.
The steps to be followed for a control write transfer are as follows:
Setup Stage Transaction:
1. MCU initializes in endpoint 0 and out endpoint 0 by programming the appropriate USB endpoint
configuration blocks. This entails programming the buffer size and buffer base address, selecting the buffer
mode, enabling the endpoint interrupt, initializing the TOGGLE bit, enabling the endpoint, and clearing the
NACK bit for both in endpoint 0 and out endpoint 0.
2. The host PC sends a setup token followed by the setup data packet addressed to out endpoint 0. If the data
is received without an error, then the UBM writes the data to the setup data packet buffer, set the setup stage
transaction (SETUP) bit to a 1 in the USB status register, return an ACK handshake to the host PC, and
assert the setup stage transaction interrupt. Note that as long as the setup transaction stage (SETUP) bit
is set to a 1, the UBM returns a NACK handshake for any data stage or status stage transactions
transactions regardless of the endpoint 0 NACK or STALL bit values.
3. The MCU services the interrupt and reads the setup data packet from the buffer then decodes the
command. If the command is not supported or valid, the MCU should set the STALL bit in the out endpoint
0 configuration byte and the endpoint 0 configuration byte before clearing the setup stage transaction
(SETUP) bit. This causes the device to return a STALL handshake for any data stage or status stage
transactions. After reading the data packet and decoding the command, the MCU clears the interrupt, which
automatically clears the setup stage transaction status bit. The MCU also sets the TOGGLE bit in the out
endpoint 0 configuration byte to a 1. For control write transfers, the PID used by the host for the first out data
packet is a DATA1 PID and the TOGGLE bit must match.
Data Stage Transaction:
1. The host PC sends an out token packet followed by a data packed addressed to out endpoint 0. If the data
packet is received without errors then the UBM writes the data to the endpoint buffer, updates the data count
value, toggles the TOGGLE bit, sets the NACK bit to a 1, returns an ACK handshake to the host PC, and
asserts the endpoint interrupt.
2. The MCU services the interrupt and reads the data packet from the buffer. To read the data packet, the MCU
first must obtain the data count value. After reading the data packet, the MCU must clear the interrupt and
clear the NACK bit to allow the reception of the next data packet from the host PC.
2–9
3. If the NACK bit is set to a 1 when the in token packet is received, the UBM simply returns a NAK handshake
to the host PC. If the STALL bit is set to a 1 when the in token packet is received, the UBM simply returns
a STALL handshake to the host PC. If a CRC or bit stuff error occurs when the data packet is received, then
no handshake is returned to the host PC.
Status Stage Transaction:
1. For in endpoint 0, the MCU updates the data count value to zero, sets the TOGGLE bit to 1, then clears the
NACK bit to a 0 to enable the data packet to be sent to the host PC. Note that for a status stage transaction
a null data packet with a DATA1 PID is sent to the host PC.
2. The host PC sends an in token packet addressed to in endpoint 0. After receiving the in token, the UBM
transmits a null data packet to the host PC. If the data packet is received without errors by the host PC, then
an ACK handshake is returned. The UBM then toggles the TOGGLE bit, sets the NACK bit to a 1, and
asserts the endpoint interrupt.
3. If the NACK bit is set to a 1 when the in token packet is received, the UBM simply returns a NAK handshake
to the host PC. If the STALL bit is set to a 1 when the in token packet is received, the UBM simply returns
a STALL handshake to the host PC. If no handshake packet is received from the host PC, then the UBM
prepares to retransmit the same data packet again.
2.2.7.1.2 Control Write With No Data Stage Transfer (Out Transfer)
The host PC uses a control write transfer to write data to the USB function. A control write with no data stage transfer
consists of a setup stage transaction and an in status stage transaction. For this type of transfer, the data to be written
to the USB function is contained in the two byte value field of the setup stage transaction data packet.
The steps to be followed for a control write with no data stage transfer are as follows:
1. MCU initializes in endpoint 0 and out endpint 0 by programming the appropriate USB endpoint configuration
blocks. This entails programming the buffer size and buffer base address, selecting the buffer mode,
enabling the endpoint interrupt, initializing the TOGGLE bit, enabling the endpoint, and clearing the NACK
bit for both in endpoint 0 and out endpoint 0.
Setup Stage Transaction:
2. The host PC sends a setup token packet followed by the setup data packet addressed to out endpoint 0.
If the data is received without an error then the UBM writes the data to the setup data packet buffer, sets
the setup state transaction (SETUP) bit to a 1 in the USB status register, returns an ACK handshake to the
host PC, and asserts the setup stage transaction interrupt. Note that as long as the setup transaction
(SETUP) bit is set to a 1, the UBM returns a NAK handshake for any data stage or status stage transactions
regardless of the endpoint 0 NACK or STALL bit values.
3. The MCU services the interrupt and reads the setup data packet from the buffer then decodes the
command. If the command is not supported or valid, the MCU sets the STALL bit in the out endpoint 0
configuration byte and the in endpoint 0 configuration byte before clearing the setup stage transaction
(SETUP) bit. This causes the device to return a STALL handshake for an data stage or status stage
transactions. After reading the data packet and decoding the command, the MCU clears the interrupt, which
automatically clears the setup stage transaction status bit.
Data Stage Transaction (s): Note, there are no data stage transactions for this type of transfer.
Status Stage Transaction:
1. For in endpoint 0, the MCU updates the data count value to zero, sets the TOGGLE bit to 1, then clears the
NACK bit to a 0 to enable the data packet to be sent to the host PC. Note that for a status stage transaction
a null data packet with a DATA1 PID is sent to the host PC.
2. The host PC sends an in taken packet addressed to in endpoint 0. After receiving the in token, the UBM
transmits a null data packet to the host PC. If the data packet is received without errors by the host PC, then
an ACK handshake is returned. The UBM then toggles the TOGGLE bit, sets the NACK bit to a 1, and
asserts the endpoint interrupt.
2–10
3. If the NACK bit is set to a 1 when the in token packet is received, the UBM simply returns a NAK handshake
to the host PC. If the STALL bit is set to a 1 when the in token packet is received, the UBM simply returns
a STALL handshake to the host PC. If no handshake packet is received from the host PC, then the UBM
prepares to retransmit the same data packet again.
2.2.7.1.3 Control Read Transfer (In Transfer)
The host PC uses a control read transfer to read data from the USB function. A control read transfer consists of a
setup stage transaction, at least one in data stage transaction, and an out-status stage transaction.
The steps to be followed for a control read transfer are as follows:
1. MCU initializes in endpoint 0 and out endpoint 0 by programming the appropriate USB endpoint
configuration blocks. This entails programming the buffer size and buffer base address, selecting the buffer
mode, enabling the endpoint interrupt, initializing the TOGGLE bit, enabling the endpoint, and clearing the
NACK bit for both in endpoint 0 and out endpoint 0.
Setup Stage Transaction:
2. The host PC sends a setup token followed by the setup data packet addressed to out endpoint 0. If the data
is received without an error, then the UBM writes the data to the setup data packet buffer, sets the setup
stage transaction (SETUP) bit to a 1 in the USB status register, returns an ACK handshake to the host PC,
and asserts the setup stage transaction interrupt. Note that as long as the setup transaction stage
transactions (SETUP) bit is set to a 1, the UBM returns a NACK handshake for any data stage or status stage
transactions regardless of the endpoint 0 NACK or STALL bit values.
3. The MCU services the interrupt and reads the setup data packet from the buffer then decodes the
command. If the command is not supported or valid, the MCU sets the STALL bit in the out endpoint 0
configuration byte and the endpoint 0 configuration byte before clearing the setup stage transaction
(SETUP) bit. This causes the device to return a STALL handshake for any data stage or status stage
transactions. After reading the data packet and decoding the command, the MCU clears the interrupt, which
automatically clears the setup stage transaction status bit. The MCU also sets the TOGGLE bit in the out
endpoint 0 configuration byte to a 1. For control read transfers, the PID used by the host for the first out data
packet is a DATA1 PID.
Data Stage Transaction:
1. The data packet to be sent to the host PC is written to the in endpoint 0 buffer by the MCU. The MCU also
updates the data count value then clears the in endpoint 0 NACK bit to a 0 to enable the data packet to be
sent to the host PC.
2. The host PC sends an out token packet addressed to out endpoint 0. After receiving the in token, the UBM
transmits the data packet to the host PC. If the data packet is received without an error by the host PC, then
an ACK handshake is returned. The UBM will then toggle the TOGGLE bit, set the NACK bit to a 1 and assert
the endpoint interrupt.
3. The MCU services the interrupt and prepares to send the next data packet to the host PC.
4. If the NACK bit is set to a 1 when the in token packet is received, the UBM simply returns a NAK handshake
to the host PC. If the STALL bit is set to a 1 when the in token packet is received, the UBM simply returns
a STALL handshake to the host PC. If no handshake packet is received from the host PC, then the UBM
prepares to retransmit the same data packet again.
5. MCU continues to send data packets until all data has been sent to the host PC.
Status Stage Transaction:
1. For output endpoint0, the MCU sets the TOGGLE bit to 1, then clears the NACK bit to a 0 to enable the data
packet to be sent to the host PC. Note that for a stage transaction a null data packet with the DATA1 PID
is sent to the host PC.
2. The host PC sends an out token packet addressed to out endpoint0. If the data packet is received without
an error the UBM updates the data count value, toggles to the TOGGLE bit, sets the NACK bit to a 1, returns
an ACK handshake to the host PC, and asserts the endpoint interrupt.
2–11
3. The MCU services the interrupt. If the status transaction completed successfully, then the MCU clears the
interrupt and clears the NACK bit.
4. If the NACK bit is set to a 1 when the in token packet is received, the UBM simply returns a NAK handshake
to the host PC. If the STALL bit is set to a 1 when the in token packet is received, the UBM simply returns
a STALL handshake to the host PC. If a CRC or bit stuff error occurs when the data packet is received, then
no handshake is returned to the host PC.
2.2.7.2 Interrupt Transfers
The TAS1020 supports interrupt data transfers both to and from the host PC. Devices that need to send or receive
a small amount of data with a specified service period should use the interrupt transfer type. In endpoints 1 through
7 and out endpoints 1 through 7 can all be configured as interrupt endpoints.
2.2.7.2.1 Interrupt Out Transaction
The steps to be followed for a interrupt out transaction are as follows:
1. MCU initializes one of the out endpoints as an out interrupt endpoint by programming the appropriate USB
endpoint configuration block. This entails programming the buffer size and buffer base address, selecting
the buffer mode, enabling the endpoint interrupt, initializing the toggle bit, enabling the endpoint and clearing
the NACK bit.
2. The host PC sends an out token packet followed by a data packet addressed to the out endpoint. If the data
is received without an error then the UBM writes the data to the endpoint buffer, updates the data count
value, toggles the toggle bit, sets the NACK bit to a 1, returns an ACK handshake to the host PC, and asserts
the endpoint interrupt.
3. The MCU services the interrupt and reads the data packet from the buffer. To read the data packet, the MCU
first must obtain the data count value. After reading the data packet, the MCU clears the interrupt and clears
the NACK bit to allow the reception of the next data packet from the host PC.
4. If the NACK bit is set to a 1 when the data packet is received, the UBM simply returns a NACK handshake
to the host PC. If the STALL bit is set to a 1 when the in token packet is received, the UBM simply returns
a STALL handshake to the host PC. If a CRC or bit stuff error occurs when the data packet is received, then
no handshake is returned to the host PC.
NOTE: In double buffer mode for interrupt out transactions, the UBM selects between the X
and Y buffer based on the value of the toggle bit. If the toggle bit is a 0, the UBM writes the data
packet to the X buffer. If the toggle bit is a 1, the UBM writes the data packet to the Y buffer.
When a data packet is received, the MCU determines which buffer contains the data packet
by reading the toggle bit. However, when using double buffer mode, the possibility exists for
data packets to be received and written to both the X and Y buffer before the MCU responds
to the endpoint interrupt. In this case, by simply using the toggle bit to determine which buffer
contains the data packet does not work. Hence, in double buffer mode, the MCU reads the X
buffer NACK bit, the Y buffer NACK bit, and the toggle bit to determine the status of the buffers.
2.2.7.2.2 Interrupt In Transaction
The steps to be followed for an interrupt in transaction are as follows:
1. MCU initializes one of the in endpoints as an in interrupt endpoint by programming the appropriate USB
endpoint configuration block. This entails programming the buffer size and buffer base address, selecting
the buffer mode, enabling the endpoint interrupt, initializing the toggle bit, enabling the endpoint, and setting
the NACK bit.
2. The data packet to be sent to the host PC is written to the buffer by the MCU. The MCU also updates the
data count value then clears the NACK bit to 0 to enable the data packet to be sent to the host PC.
2–12
3. The host PC sends an in token packet addressed to the in endpoint. After receiving the in token, the UBM
transmits the data packet to the host PC. If the data packet is received without errors by the host PC, then
an ACK handshake is returned. The UBM then toggles the toggle bit, sets the NACK bit to a 1, and asserts
the endpoint interrupt.
4. The MCU services the interrupt and prepares to send the next data packet to the host PC.
5. If the NACK bit is set to a 1 when the in token packet is received, the UBM simply returns a NACK handshake
to the host PC. If the STALL bit is set to a 1 when the in token packet is received, the UBM simply returns
a STALL handshake to the host PC. If no handshake packet is received from the host PC, then the UBM
prepares to retransmit the same data packet again.
NOTE: In double buffer mode for interrupts in transactions, the UBM selects between the X and
Y buffer based on the value of the toggle bit. If the toggle bit is a 0, the UBM will read the data
packet to the X buffer. If the toggle bit is a 1, the UBM will read the data packet to the Y buffer.
2.2.7.3 Bulk Transfers
The TAS1020 supports bulk data transfers both to and from the host PC. Devices that need to send or receive a large
amount of data without a suitable bandwidth should use the bulk transfer type. In endpoints 1 through 7 and out
endpoints 1 through 7 can be configured as bulk endpoints. TAS1020 supports single and double buffering for bulk
transfers.
2.2.7.3.1 Bulk Out Transaction Using MCU
The steps to be followed for a bulk out transaction are as follows:
1. MCU initializes one of the out endpoints as an out bulk endpoint by programming the appropriate USB
endpoint configuration block. This entails programming the buffer size and buffer base address, selecting
the buffer mode, enabling the endpoint interrupt, initializing the toggle bit, enabling the endpoint, and
clearing the NACK bit.
2. The host PC sends an out token packet followed by a data packet addressed to the out endpoint. If the data
is received without an error then the UBM writes the data to the endpoint buffer, updates the data count
value, toggles the toggle bit, sets the NACK bit to a 1, returns an ACK handshake to the host PC, and asserts
the endpoint interrupt.
3. The MCU services the interrupt and reads the data packet from the buffer. To read the data packet, the MCU
first needs to obtain the data count value. After reading the data packet, the MCU clears the interrupt and
clears the NACK bit to allow the reception of the next data packet from the host PC.
4. If the NACK bit is set to a 1 when the data packet is received, the UBM simply returns a NACK handshake
to the host PC. If the STALL bit is set to a 1 when the data packet is received, the UBM simply returns a
STALL handshake to the host PC. If a CRC or bit stuff error occurs when the data packet is received, then
no handshake is returned to the host PC.
NOTE: In double buffer mode for bulk out transactions, the UBM selects between the X and
Y buffer based on the value of the toggle bit. If the toggle bit is a 0, the UBM writes the data
packet to the X buffer. If the toggle bit is a 1, the UBM writes the data packet to the Y buffer.
When a data packet is received, the MCU determines which buffer contains the data packet
by reading the toggle bit. However, when using double buffer mode, data packets may be
received and written to both the X and Y buffer before the MCU responds to the endpoint
interrupt. In this case, simply using the toggle bit to determine which buffer contains the data
packet does not work. Hence, in double buffer mode, the MCU reads the X buffer NACK bit,
the Y buffer NACK bit, and the toggle bit to determine the status of the buffers.
2–13
2.2.7.3.2 Bulk In Transaction Using MCU
The steps to be followed for a bulk in transaction are as follows:
1. MCU initializes one of the in endpoints as an in bulk endpoint by programming the appropriate USB endpoint
configuration block. This entails programming the buffer size and buffer base address, selecting the buffer
mode, enabling the endpoint interrupt, initializing the toggle bit, enabling the endpoint and setting the NACK
bit.
2. The data packet to be sent to the host PC is written to the buffer by the MCU. The MCU also updates the
data count value then clears the NACK bit to a 0 to enable the data packet to be sent to the host PC.
3. The host PC sends an in token packet addressed to the in endpoint. After receiving the in token, the UBM
transmits the data packet to the host PC. If the data packet is received without errors by the host PC, then
an ACK handshake is returned. The UBM then toggles the toggle bit, sets the NACK bit to a 1, and asserts
the endpoint interrupt.
4. The MCU services the interrupt and prepares to send the next data packet to the host PC.
5. If the NACK bit is set to a 1 when the in token packet is received, the UBM simply returns a NAK handshake
to the host PC. If the STALL bit is set to a 1 when the in token packet is received, the UBM simply returns
a STALL handshake to the host PC. If no handshake packet is received from the host PC, then the UBM
prepares to retransmit the same data packet again.
NOTE: In double buffer mode for bulk in transactions, the UBM selects between the X and Y
buffer based on the value of the toggle bit. If the toggle bit is a 0, the UBM reads the data packet
to the X buffer. If the toggle bit is a 1, the UBM reads the data packet to the Y buffer.
2.2.7.3.3 Bulk Out Transaction Through DMA
This transaction is used for mass storage class USB applications to move bulk data through DMA to C-Port. C-Port
can be programmed in General Purpose mode or AC97 mode. When in general purpose mode, SYNC is disabled
when no data is there to send out. In the AC97 mode, Tag fields are de-asserted when no valid data is in the buffer
to be sent out.
A sample for the Bulk Out transaction is the number of bytes to be transferred in a codec frame.
Two modes of transfer are possible. The first one is the software handshake mode using MCU and external controller
(DSP) and the second one is no handshake mode where MCU intervention is less for higher rates of transfer.
Software Handshake Using MCU and External Controller (DSP)
The following steps explain the operation:
1. hsken (Handshake enable) bit in DMA channel control definition register = 1.
2. UBM after receiving BULK packet, it puts it into the buffer, sets the NACK bit and the data count in the data
count register, and generates an interrupt to the MCU.
3. MCU after receiving interrupt can decide to use DMA to send the packet to C-Port.
4. MCU decides how many BULK OUT packets need to be handled by DMA without MCU intervention. MCU
writes this value (16-bit) to DMAPCNT1, MDMAPCNT0 registers.
5. MCU configures the C-Port to be in AC97/GP modes. If C-Port is used as GP mode, then MCU must set
the CptBlk bit in GLOBCTRL register.
6. Then, MCU enables the DMA.
7. DMA then transfers data through the C-Port and once it finishes the number of packets programmed by
MCU, it disables itself and then generates DMA0 or DMA1 interrupt to MCU.
8. MCU after receiving DMA interrupt will know that the DMAPCNT packets are sent out to the C-Port and
takes control again.
2–14
9. Handshaking between MCU and DSP can be done in software at a higher level, depending on the
application.
No Handshake Mode
If the MCU intervention in the above handshake mode limits the bandwidth on the BULK out endpoint, no Handshake
mode can be used.
1. hsken (Handshake enable) bit in DMA channel control definition register = 0.
2. MCU configures the C-Port to be in AC97/GP modes. If C-Port is used as GP mode, then MCU must set
the CptBlk bit in GLOBCTRL register.
3. MCU configures the endpoint configuration registers and enables the DMA.
4. Now handshaking is only between DMA and UBM. DMA moves data once it is filled by UBM. This continues
until MCU disables DMA.
2.2.7.3.4 Bulk In Transaction Through DMA
TAS1020 does not support BULK IN through DMA.
2.2.7.4 ISO OUT/IN. USB to/from C-Port Through DMA
2.2.7.4.1 ISO Out
Here the ISO packets from the host are received by UBM and put into the buffer. DMA collects the data from the buffer
and streams it through the C-Port to a codec or a DSP. DMA looks at the UBM writer pointers to make a decision about
the availability of ISO data in the buffer. C-Port can be programmed into different modes based on the application
and the codecs being used. Here MCU must program the endpoint configuration registers, DMA and C-Port. DMA
also updates the buffer content registers which is the difference of UBM writer pointer and DMA read pointer after
the end of every USB frame.
•
UBM Operation
–
Reads endpoint configuration byte. Checks if endpoint is enabled. If not enabled, ignores the ISO
packet.
–
If it is ISO endpoint, checks the endpoint number with the endpoint number in the DMA channel 0/1
definition register. If either of the DMA channels is used, UBM behaves as described below. If not, the
ISO traffic is directed to MCU, which the MCU is able to handle it in a different way.
–
Reads OEPBBAXn. This is the starting address for the circular buffer being used for the endpoint. For
the first ISO OUT packet UBM initializes the write pointer to OEPBBAXn. UBM locally stores this starting
address as MCU can relocate the buffer anytime. Each time an ISO OUT packet comes, UBM compares
this local buffer starting address with OEPBBAXn. If this is not same, UBM re-initializes the write pointer
to OEPBBAXn.
–
Reads OEPSIZn. This is the circular buffer size for the ISO endpoint. This is used to wrap-around the
UBM write pointer to the starting address of the buffer when it reaches the end of the buffer.
–
Buffer end address = buffer starting address + buffer size
–
UBM proceeds with reading the data from the SIE and storing the data into the circular buffer in the
shared RAM. The 11-bit write pointer is incremented after receiving each byte. Once the buffer write
pointer reaches the buffer end address, UBM rewinds the write pointer to the starting buffer address.
–
At the end of transaction, UBM updates the sample count in the OEPDCNTX or OEPDCNTY register
based on the LSB of frame counter.
–
NAK bit not used for ISO to DMA.
2–15
–
If UBM write pointer overtakes the DMA read pointer, UBM sets the buffer overflow (OVF) bit in the ISO
endpoint configuration register.
–
UBM write pointer is reset to the buffer starting address once DMA is disabled.
DMA Operation
•
DMA must be enabled before getting any ISO packets from the Host. Typically, MCU enables the DMA
before playing audio to the device.
–
After DMA is enabled, it reads the DMA channel control register to get the endpoint number and
direction.
–
Based on the endpoint number, it reads the endpoint configuration register. If it is ISO endpoint, it works
as follows.
–
DMA reads the OEPBBAXn, OEPBSIZn registers to determine the buffer starting address and buffer
size.
–
DMA reads the C-port registers to understand the C-port mode.
–
DMA reads the DMA time slot assignment registers.
–
DMA, for the first time, keeps monitoring the OEPDCNTXn or OEPDCNTYn register to see if an ISO
OUT packet is received. Once a new ISO OUT packet is received, DMA waits for next SOF/PSOF
signaling and goes to the next step.
–
DMA starts with the read pointer equal to the buffer starting address. Once an ISO OUT packet is
received, the UBM pointer is incremented very fast as the ISO OUT is packet is received at 12 Mb/sec.
–
DMA starts reading the samples out of the buffer and sends to the C-port till it catches up with the UBM
pointer.
–
Each time DMA receives SOF/PSOF signaling, it completes streaming the current sample, and
calculates the buffer content based on UBM write pointer and DMA read pointer. Buffer content is in
number of bytes. This buffer size is written into DmaBCnt0/DMABCnt1 registers.
NOTE: In AC97 mode, if buffer under-run happens, DMA should send this information to the
C-port to clear the tag bits for the corresponding slots to indicate that the data in those codec
frames is invalid. For I2S, AIC, GP modes, it must send zeros. C-port logic sends zeros if DMA
does not stream anything to the C-port for a codec frame.
2.2.7.4.2 ISO IN
The serial data coming from the codec/DSP is received by the C-Port. DMA moves the bytes from C-Port holding
registers into the buffer and updates the endpoint data count registers. UBM packetizes the data and sends the
packets to host when it receives an ISO IN request. MCU has to program the endpoint configuration registers, DMA
and C-Port. The following section explains how DMA and UBM works.
UBM Operation
2–16
•
After ISO IN token is received, UBM reads the endpoint configuration register if the endpoint is enabled.
If not enabled, it ignores the IN request.
•
UBM reads the IEPBBAXn, IEPBSIZXn registers to get the circular buffer starting address and buffer size
and calculates the buffer maximum address.
•
UBM reads IEPDCNTXn or IEPDCNTYn depending on the LSB of the frame counter register to determine
how many samples (bytes) need to be transferred to the host.
•
UBM initializes the read pointer to one of the 11-bit pointers from DMA(depending on the LSB of frame
counter) to start reading the samples out of the buffer. If the address reaches buffer maximum address UBM
rewinds the read pointer to the buffer starting address.
•
After the last sample is moved to the SIE transmit holding registers, UBM clears the data count register for
the IEPDCNTXn or IEPDCTNYn registers.
DMA Operation
•
In general, DMA must packetize the serial data coming from the C-port for 1 ms before UBM sends it to the
host when an ISO IN token is received.
•
If DMA draws packet boundaries when it receives SOF/PSOF, then it might be in the middle of receiving
a sample when an IN token is received. Hence, DMA must finish packetizing way before the SOF/PSOF.
For the worst case, at 8kHz, there are 8 codec frames in 1 USB frame. So, to make room for one 8-kHz codec
frame, the IN packet switch point should occur at least 12000% 8 = 1500 USB clocks before SOF. Taking
the variation in USB clocks per SOF into account, the IN packet switch event is set to 1511 USB_clocks
before SOF/PSOF.
•
After DMA is enabled, it reads all the DMA control registers, DMA time slot registers, the endpoint base
address, and size registers.
•
DMA write pointer is initialized to the buffer start address.
•
As DMA packetizes continuously regardless of host sending ISO IN tokens, DMA must pass pointers to
UBM to clearly tell the UBM about the packet boundaries for each USB frame.
•
Two data count registers are required in the IN direction.
•
DMA waits for IN packet switch event to start its operation. At this time DMA stores its write pointer to convey
the buffer start address for this packet to UBM.
•
DMA has to pass two pointers based on the LSB of the frame counter.
•
DMA stores the samples into the buffer, incrementing its 11-bit write pointer.
•
Once it receives next packet switch event, the DMA puts the last sample into the buffer and updates the
IEPDCNTXn or IEPDCNTYn data count register with the number of samples received based on the LSB
of the frame counter.
2.2.8
Microcontroller Unit
The 8052 core used in the TAS1020 is based on the industry standard 8052 MCU and is software compatible with
the 8052, 8032, 80C52, 80C53, and 87C52 MCUs. Therefore, refer to a standard 8052 data manual for more details,
if needed.
2.2.9
External MCU Mode Operation
The external MCU mode of operation is provided for firmware development using an in-circuit emulator (ICE). In the
external MCU mode, the internal 8052 MCU core of the TAS1020 is disabled. Also in the external MCU mode, the
GPIO ports are used for the external MCU data, address, and control signals. Refer to section 1.7, Terminal Functions
– External MCU Mode, for details. In this mode, the external MCU or ICE is able to access the memory mapped IO
registers, the USB configuration blocks and the USB buffer space. Refer to section 1.8, Device Operation Modes,
for information regarding the various modes of operation.
Texas Instruments has developed the TAS1020 evaluation module (EVM) to allow customers to develop application
firmware and to evaluate device performance. The EVM board provides a 40-pin dip socket for an ICE and headers
to allow expansion of the system in a variety of ways.
2.2.10 Interrupt Logic
The 8052 MCU core used in the TAS1020 supports all the standard interrupt sources. The five standard MCU interrupt
sources are timer 0, timer 1, serial port, external 1 (INT1), and external 0 (INT0).
All of the additional interrupt sources within the TAS1020 device are read together to generate the INT0 signal to the
MCU. Refer to the interrupt vector register for more details on the other TAS1020 interrupt sources.
2–17
The other interrupt sources are: the eight USB in end-points, the eight USB out end-points, USB function reset, USB
function suspend, USB function resume, USB start-of-frame, USB pseudo start-of-frame, USB setup stage
transaction, USB setup stage transaction over-write, codec port interface transmit data register empty, codec port
interface receive data register full, I2C interface transmit data register empty, I2C interface receive data register full,
and the external interrupt input.
The interrupts for the USB in end-points and USB out end-points can be masked. An interrupt for a particular end-point
occurs at the end of a successful transaction to that end-point. A status bit for each in and out end-point also exists.
However, these status bits are read only, and therefore, these bits are intended to be used for diagnostic purposes
only. After a successful transaction to an end-point, both the interrupt and status bit for an end-point are asserted until
the interrupt is cleared by the MCU.
The USB function reset, USB function suspend, USB function resume, USB start-of-frame, USB pseudo
start-of-frame, USB setup stage transaction, and USB setup stage transaction over-write interrupts can all be
masked. A status bit for each of these interrupts also exists. Refer to the USB interrupt mask register and the USB
status register for more details. Note that the status bits for these interrupts are read only. For these interrupts, both
the interrupt and status bit are asserted until the interrupt is cleared by the MCU.
The codec port interface transmit data register empty, codec port interface receive data register full, I2C Interface
transmit data register empty, and I2C interface receive data register full interrupts can all be masked. A status bit for
each of these interrupts also exists. Note that the status bits for these interrupts are read only. However, for these
interrupts, the status bits are not cleared automatically when the interrupt is cleared by the MCU. Refer to the codec
port interface control/status register and the I2C interface control/status register for more details.
The external interrupt input (XINT) is also read together with the on-chip interrupt sources. An enable bit exists for
this interrupt in the global control register. This interrupt does not have a status bit.
2.2.11 DMA Controller
The TAS1020 provides two DMA channels for transferring data between the USB end-point buffers and the codec
port interface. The DMA channels are provided to support the streaming of data for USB isochronous end-points only.
Each DMA channel can be programmed to service only one isochronous end-point. The end-point number and
direction are programmable using the DMA channel control register provided for each of the DMA channels.
A DMA channel can also be used to send bulk endpoint data to the C-port for higher throughput. For more details
refer to the Bulk Out Transaction Using DMA section 2.2.7.3.3.
The codec port interface time slots to be serviced by a particular DMA channel must also be programmed. For
example, an AC’97 mode stereo speaker application uses time slots 3 and 4 for audio playback. Therefore, the DMA
channel used to move the audio data to the codec port interface must set time slot assignment bits 3 and 4 to a 1.
Each DMA channel is capable of being programmed to transfer data for time slots 0 through 13 using the two DMA
channel time slot assignment registers provided for each DMA channel.
The number of bytes to be transferred for each time slot is also programmable. The number of bytes used must be
set based on the desired audio data format.
2.2.12 Codec Port Interface
The codec port interface is a configurable serial interface used to transfer data between the TAS1020 IC and a codec
device. The serial protocol and formats supported include AC ’97 1.0, AC ’97 2.0, and several I2S modes. In addition,
a general-purpose mode is provided that can be configured to various user defined serial interface formats. The
TAS1020 also provides a bulk mode where DMA can send bulk data to C-port directly.
Configuration of the interface is accomplished using the four codec port interface configuration registers: CPTCNF1,
CPTCNF2, CPTCNF3, and CPTCNF4. In I2S mode 5, CPTRXCNF2, CPTRXCNF3, and CPTRXCNF4 are used to
configure the C-port in receive direction. Refer to section A.5.4 for more details on these registers. The serial interface
is a time division multiplexed (TDM) time slot based scheme. The basic serial format is programmed by setting the
number of time slots per codec frame and the number of serial clock cycles (or bits) per time slot. The interface in
2–18
all modes is bidirectional and full duplex. For some modes, both audio data and command/status data are transferred
via the serial interface. The sources of the USB end-point data buffer are the transmit data and destination of the
receive data for all audio data time slots. Transfer of the audio data packets to/from the USB end-point data buffers
and the codec port interface is controlled by one or more of the DMA channels. Remember that each DMA channel
can be assigned to one USB isochronous end-point. The source and/or the destination of the command/status
address and data values is the MCU.
The features of the codec port interface that can be configured are:
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
The mode of operation
The number of time slots per codec frame
The number of serial clock cycles for slot 0
The number of serial clock cycles for all slots other than slot 0
The number of valid data bits per audio data time slot
The time slots to be used for command/status address and data
The serial clock (CSCLK) frequency in relation to the codec master clock (MCLK) frequency
The source of the serial clock signal (internally generated or an input from the codec device)
The source of the codec master clock signal used to generate the internal serial clock signal (internally
generated by the ACG or an input to the TAS1020 device)
The polarity, duration, and direction of the codec frame sync signal
The relationship between the codec frame sync signal and the serial clock signal
The relationship between the codec frame sync signal and the serial data signals
The relationship between the serial clock signal and the serial data signals
The use of zero padding or a 3-state level for unused time slots and/or bits
The byte ordering to be used
2.2.12.1 Audio Codec (AC) ’97 1.0 Mode of Operation
In AC ’97 1.0 mode, the codec port interface can be configured as an AC link serial interface to the AC ’97 codec
device. Refer to the Audio codec ’97 Specification Revision 1.03 for additional information. The AC link serial interface
is a time division multiplexed (TDM) slot based serial interface that is used to transfer both audio data and
command/status data between the TAS1020 IC and the codec device.
Table 2–3. Terminal Assignments for Codec Port Interface AC ’97 1.0 Mode
TERMINAL
1 0 MODE 2
AC ’97 VERSION 1.0
NO.
NAME
35
CSYNC
SYNC
37
CSCLK
BIT_CLK
I
38
CDATO
SD_OUT
O
36
CDATI
SD_IN
I
34
CRESET
RESET
O
32
CSCHNE
NC
O
O
In this mode, the codec port interface is configured as a bidirectional full duplex serial interface with a fixed rate of
48 kHz. Each 48-kHz frame is divided into 13 time slots, with the use of each time slot predefined by the Audio codec
’97 Specification. Each time slot is 20 serial clock cycles in length except for time slot 0, which is only 16 serial clock
cycles. The serial clock, which is referred to as the BIT_CLK for AC ’97 modes, is set to 12.288 MHz. Based on the
length of each slot, there is a total of 256 serial clock cycles per frame at a frequency of 12.288 MHz. As a result the
frame frequency is 48 kHz. For the AC ’97 modes, the BIT_CLK is input to the TAS1020 device from the codec. The
BIT_CLK is generated by the codec from the master clock (MCLK) input. The codec MCLK input, which can be
generated by the TAS1020 device, must be a frequency of 24.576 MHz. The start of each 48-kHz frame is
2–19
synchronized to the rising edge of the SYNC signal, which is an output of the TAS1020 device. The SYNC signal is
driven high each frame for the duration of slot 0. See Figure 2–2 for details on connecting the TAS1020 to a codec
device in this mode.
TAS1020
AC’97 IC
MCLKO1
AC97CLK
CSYNC
SYNC
CSCLK
BIT_CLK
CDATO
SD_IN
CDATI
SD_OUT
CRESET
CRESET
CSCHNE
Figure 2–2. Connection of the TAS1020 to an AC ’97 Codec
The AC link protocol defines slot 0 as a special slot called the tag slot and defines slots 1 through 12 as data slots.
Slot 1 and slot 2 are used to transfer command and status information between the TAS1020 device and the codec.
Slot 1 and slot 2 of the outgoing serial data stream are defined as the command address and command data slots,
respectively. These slots are used for writing to the control registers in the codec. Slot 1 and slot 2 of the incoming
serial data stream are defined as the status address and status data slots, respectively. These slots are used for
reading from the control registers in the codec.
Unused or reserved time slots and unused bit locations within a valid time slot are filled with zeros. Since each data
time slot is 20 bits in length, the protocol supports 8-bit, 16-bit, 18-bit, or 20-bit data transfers.
2.2.12.2 Audio Codec (AC) ’97 2.0 Mode of Operation
The basic serial protocol for the AC ’97 2.0 mode is the same as the AC ’97 1.0 mode. The AC ’97 2.0 mode, however,
offers some additional features. In this mode, the TAS1020 provides support for multiple codec devices and also
on-demand sampling. The TAS1020 can connect directly to two AC ’97 codecs as shown in Figure 2–3. Note that
if only one codec is used, then the SD_IN2 input (pin 40) should be tied to DVSS.
Table 2–4. Terminal Assignments for Codec Port Interface AC ’97 2.0 Mode
TERMINAL
2–20
AC ’97 VERSION 2.0
2 0 MODE 3
NO.
NAME
35
CSYNC
SYNC
37
CSCLK
BIT_CLK
I
38
CDATO
SD_OUT
O
36
CDATI
SD_IN1
I
34
CRESET
RESET
O
32
CSCHNE
SD_IN2
I
O
TAS1020
AC’97 IC
MCLKO
CSYNC
CSCLK
CDATO
CDATI
CRESET
CSCHNE
AC97CLK
SYNC
BIT_CLK
SD_IN
SD_OUT
CRESET
Primary
AC97 or MC97
AC97CLK
SYNC
BIT_CLK
SD_IN
SD_OUT
CRESET
Secondary
Figure 2–3. Connection of the TAS1020 to Multiple AC ’97 Codecs
2.2.12.3 Inter-IC Sound (I2S) Modes of Operation
The TAS1020 offers two I2S modes of operation. However, the serial format is the same for these two I2S modes.
The difference in the I2S modes is simply the number of serial data outputs and/or serial data inputs supported. For
instance, in codec port interface mode 4, there is one serial data output (SDOUT1) and two serial data inputs (SDIN1,
SDIN2). Hence, mode 4 can be used to connect the TAS1020 device to a codec with one stereo DAC and two ADCs.
Table 2–5 shows the TAS1020 codec terminal assignments and the respective signal names for each of the I2S
modes.
Table 2–5. Terminal Assignments for Codec Port Interface I2S Modes
TERMINAL
NO.
NAME
I2S
MODE 4
I2S
MODE 5
35
CSYNC
LRCK
O
LRCK1
O
37
CSCLK
SCLK
O
SCLK1
O
38
CDATO
SDOUT1
O
SDOUT1
O
36
CDATI
SDIN1
I
SDIN2
I
34
CRESET
CRESET
O
SCLK2
O
32
CSCHNE
SDIN2
I
LRCK2
O
In all I2S modes, the codec port interface is configured as a bidirectional full duplex serial interface with two time slots
per frame. The frame sync signal is the left/right clock (LRCK) signal. Time slot 0 is used for the left channel audio
data, and time slot 1 is used for the right channel audio data. Both time slots must be set to 32 serial clock (SCLK)
cycles in length giving an SCLK-to-LRCK ratio of 64. The serial clock frequency is based on the audio sample rate
and the codec master clock (MCLK) frequency. For example, when using an audio sample rate (FS) of 48 kHz and
an MCLK frequency of 12.288 MHz (256xFS), the SCLK frequency must be set to 3.072 MHz (64xFS). Note that the
codec frame sync, the audio sample rate (FS), and the LRCK are all synonymous.
The LRCK signal has a 50% duty cycle. The LRCK signal is low for the left channel time slot and is high for the right
channel time slot. In addition, the LRCK signal is synchronous to the falling edge of the SCLK. Serial data is shifted
out on the falling edge of SCLK and shifted in on the rising edge of SCLK. There is a one SCLK cycle delay from the
edge of the LRCK before the most significant bit of the data is shifted out for both the left channel and right channel.
For the I2S modes of the codec port interface, there is a 24-bit transmit and 24-bit receive shift register for each
SDOUT and SDIN signal, respectively. As a result, the interface can actually support 16-bit, 18-bit, 20-bit or 24-bit
transfers. The interface pads the unused bits automatically with zeros.
2–21
The I2S protocol does not provide for command/status data transfers. Therefore, when using the TAS1020 device
with a codec that uses an I2S serial interface for audio data transfers, the TAS1020 I2C serial interface can be used
for codec command/status data transfers.
In addition, the TAS1020 codec port interface is very flexible. As a result, many variations of the serial interface
protocol can be configured including an SCLK-to-LRCK ratio of 32.
2.2.12.4 Mapping of DMA Time Slots to Codec Port Interface Time Slots for I 2S Modes
The I2S serial data format requires two time slots (left channel and right channel) for each serial data output or input.
As discussed in the previous section. Each of the serial data outputs and/or inputs has a unique left channel time slot
(slot number 0) and right channel time slot (slot number 1). For the I2S modes of operation, the DMA channel time
slot assignments must be mapped to the different left channel and right channel time slots for the serial data outputs
and inputs. Each DMA channel has fourteen time slot bits, which are time slot assignment bits 0 through 13. Table 2–6
and 2–7 show the codec port interface time slot numbers and the corresponding time slot numbers for the DMA
channels.
As an example, suppose that Codec port interface mode 4 is to be used with one serial data output and two serial
data inputs. The DMA channel to be programmed to support the serial data output must have time slot assignment
bits 0 and 1 set to 1. The DMA channel to be programmed to support the serial data input must have time slot
assignment bits 0 and 2 set to 1.
Table 2–6. SLOT Assignments for Codec Port Interface I2S Mode 4
SERIAL DATA
Codec PORT INTERFACE TIME SLOT NUMBER
DMA CHANNELS(s) TIME SLOT NUMBER
LEFT CHANNEL
RIGHT CHANNEL
LEFT CHANNEL
RIGHT CHANNEL
SDOUT1
0
1
0
1
SDIN1
0
1
0
2
SDIN2
0
1
1
3
Table 2–7. SLOT Assignments for Codec Port Interface I2S Mode 5
SERIAL DATA
Codec PORT INTERFACE TIME SLOT NUMBER
DMA CHANNELS(s) TIME SLOT NUMBER
LEFT CHANNEL
RIGHT CHANNEL
LEFT CHANNEL
RIGHT CHANNEL
SDOUT1
0
1
0
1
SDIN2
0
1
0
1
2.2.12.5 General-Purpose Mode of Operation
In the general-purpose mode the codec port interface can be configured to various user defined serial interface
formats using the pin assignments shown in Table 2–8. This mode gives the user the flexibility to configure the
TAS1020 to connect to various codecs and DSPs that do not use a standard serial interface format.
Table 2–8. Terminal Assignments for Codec Port Interface General-Purpose Mode
TERMINAL
GP
MODE 0
NO.
NAME
35
CSYNC
CSYNC
I/O
37
CSCLK
CSCLK
I/O
38
CDATO
CDAT0
O
36
CDATI
CDAT1
I
34
CRESET
CRESET
O
32
CSCHNE
NC
O
2.2.12.6 AIC Mode
AIC mode is used to connect TAS1020 to a voice codec which has AIC interface as described in TI’s TLV320AIC10
data sheet.
2–22
2.2.12.7 Bulk Mode
TAS1020 supports bulk data transfer through the codec port using one of the two available DMA channels. The codec
port needs to be configured in AC97 or general purpose modes for the operation. This mode is selected by writing
a 1 to CPTBLK bit of the CPTCNF4 register. When the codec port is running in general purpose bulk mode, CSYNC
is active only when valid data is present in the current frame. In ’AC97 bulk mode, CSYNC is active all the time, but
the tag bits in slot 0 indicate the valid data.
2.2.13 I2C Interface
The TAS1020 has a bidirectional two-wire serial interface that can be used to access other ICs. This serial interface
is compatible with the I2C (Inter IC) bus protocol and supports both 100-kbps and 400-kbps data transfer rates. The
TAS1020 is a master only device that does not support a multimaster bus environment (no bus arbitration) or wait
state insertion. Hence this interface can be used to access I2C slave devices including EEPROMs and codecs. For
example, if the application program code is stored in an EEPROM on the PCB, then the MCU will download the code
from the EEPROM to the TAS1020 on-chip RAM using the I2C interface. Another example is the control of a codec
device that uses an I2S interface for audio data transfers and an I2C interface for control register read/write access.
2.2.13.1 Data Transfers
The two-wire serial interface uses the serial clock signal, SCL, and the serial data signal, SDA. As stated above, the
TAS1020 is a master only device, and therefore, the SCL signal is an output only. The SDA signal is a bidirectional
signal that uses an open-drain output to allow the TAS1020 to be wire-ORed with other devices that use open-drain
or open-collector outputs.
All read and write data transfers on the serial bus are initiated by a master device. The master device is also
responsible for generating the clock signal used for all data transfers. The data is transferred on the bus serially one
bit at a time. However, the protocol requires that the address and data be transferred in byte (8-bit) format with the
most-significant bit (MSB) transferred first. In addition, each byte transferred on the bus is acknowledged by the
receiving device with an acknowledge bit. Each transfer operation begins with the master device driving a start
condition on the bus and ends with the master device driving a stop condition on the bus.
The timing relationship between the SCL and SDA signals for each bit transferred on the bus is shown in Figure 3-7.
As shown, the SDA signal must be stable while the SCL signal is high, which also means that the SDA signal can
only change states while the SCL signal is low.
The timing relationship between the SCL and SDA signals for the start and stop conditions is shown in Figure 3-8.
As shown, the start condition is defined as a high-to-low transition of the SDA signal while the SCL signal is high. Also
as shown, the stop condition is defined as a low-to-high transition of the SDA signal while the SCL signal is high.
When the TAS1020 is the device receiving data information, the TAS1020 acknowledges each byte received by
driving the SDA signal low during the acknowledge SCL period. During the acknowledge SCL period, the slave device
must stop driving the SDA signal. If the TAS1020 is unable to receive a byte, the SDA signal is not driven low and
is pulled high external to the TAS1020 device. A high during the SCL period indicates a not-acknowledge to the slave
device. The acknowledge timing is shown in Figure 3-9.
Read and write data transfers by the TAS1020 device can be done using single byte or multiple byte data transfers.
Therefore, the actual transfer type used depends on the protocol required by the I2C slave device being accessed.
2–23
2.2.13.2 Single Byte Write
As shown is Figure 2-4, a single byte data write transfer begins with the master device transmitting a start condition
followed by the I2C device address and the read/write bit. The read/write bit determines the direction of the data
transfer. For a write data transfer, the read/write bit must be a 0. After receiving the correct I2C device address and
the read/write bit, the I2C slave device responds with an acknowledge bit. Next, the TAS1020 transmits the address
byte or bytes corresponding to the I2C slave device internal memory address being accessed. After receiving the
address byte, the I2C slave device again responds with an acknowledge bit. Next, the TAS1020 device transmits the
data byte to be written to the memory address being accessed. After receiving the data byte, the I2C slave device
again responds with an acknowledge bit. Finally, the TAS1020 device transmits a stop condition to complete the single
byte data write transfer.
Acknowledge
Start Condition
SDA
A6
A5
A4
A3
A2
A1
A0 R/W ACK A7
Acknowledge
A6
I2C Device Address and
Read/Write Bit
A5
A4
A3
A2
A1
A0
Acknowledge
ACK D7
D6
D5
Memory or Register Address
D4
D3
D2
D1
D0 ACK
Stop
Condition
Data Byte
Figure 2–4. Single Byte Write Transfer
2.2.13.3 Multiple Byte Write
A multiple byte data write transfer is identical to a single byte data write transfer except that multiple data bytes are
transmitted by the TAS1020 device to the I2C slave device as shown in Figure 2-5. After receiving each data byte,
the I2C slave device responds with an acknowledge bit.
Acknowledge
Start Condition
SDA
A6
A5
A1
A0 R/W ACK A7
I2C Device Address and
Read/Write Bit
Acknowledge
A6
A5
A4
A3
A1
Memory or Register Address
A0 ACK D7
D6
D1
D0 ACK
First Data Byte
Figure 2–5. Multiple Byte Write Transfer
2–24
Acknowledge
Acknowledge
D7
Other
Data Bytes
D6
D1
Last Data Byte
D0 ACK
Stop
Condition
2.2.13.4 Single Byte Read
As shown in Figure 2-6, a single byte data read transfer begins with the TAS1020 device transmitting a start condition
followed by the I2C device address and the read/write bit. For the data read transfer, both a write followed by a read
are actually performed. Initially, a write is performed to transfer the address byte or bytes of the internal memory
address to be read. As a result, the read/write bit must be a 0. After receiving the I2C device address and the read/write
bit, the I2C slave device responds with an acknowledge bit. Also, after sending the internal memory address byte or
bytes, the TAS1020 device transmits another start condition followed by the I2C slave device address and the
read/write bit again. This time the read/write bit is a 1 indicating a read transfer. After receiving the I2C device address
and the read/write bit the I2C slave again responds with an acknowledge bit. Next, the I2C slave device transmits the
data byte from the memory address being read. After receiving the data byte, the TAS1020 device transmits a
not-acknowledge followed by a stop condition to complete the single byte data read transfer.
Repeat Start Condition
Start
Condition
Acknowledge
A6
SDA
A5
A1
Acknowledge
A0 R/W ACK A7
I2C Device Address and
Read/Write Bit
A6
A5
A4
A0
ACK
A6
A5
A1
A0 R/W ACK D7
I2C Device Address and
Read/Write Bit
Memory or Register Address
Not
Acknowledge
Acknowledge
D6
D1
D0 ACK
Data Byte
Stop
Condition
Figure 2–6. Single Byte Read Transfer
2.2.13.5 Multiple Byte Read
A multiple byte data read transfer is identical to a single byte data read transfer except that multiple data bytes are
transmitted by the I2C slave device to the TAS1020 device as shown in Figure 2-7. Except for the last data byte, the
TAS1020 device responds with an acknowledge bit after receiving each data byte.
Repeat Start
Condition
Start
Condition
SDA
Acknowledge
A6
A0 R/W ACK A7
I2C Device Address and
Read/Write Bit
Acknowledge
A6
A7
A4
A0
Memory or Register Address
ACK
Acknowledge
A6
A0 R/W ACK D7
I2C Device Address and
Read/Write Bit
Not
Acknowledge
Acknowledge
D0 ACK
First Data Byte
D7
Other
Data Bytes
D6
D1
Last Data Byte
D0 ACK
Stop
Condition
Figure 2–7. Multiple Byte Read Transfer
2–25
2–26
3 Electrical Specifications
3.1 Absolute Maximum Ratings Over Operating Temperature Ranges (unless
otherwise noted)†
Supply voltage range, DVDD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 0.5 to 3.6 V
Input voltage range, VI: 3.3 V TTL/LVCMOS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 0.5 V to DVDD + 0.5 V
Output voltage range, VO: 3.3 V TTL/LVCMOS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 0.5 V to DVDD + 0.5 V
Continuous power dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table
Operating free air temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 70°C
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 65°C to 150°C
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
DISSIPATION RATING TABLE
PACKAGE
TA ≤ 25°C
POWER RATING
TQFP
0.923 W
DERATING FACTOR
ABOVE TA = 25°C
TA = 70°C
POWER RATING
10.256 mW/°C
0.461 W
3.2 Recommended Operating Conditions
MIN
NOM
MAX
UNIT
Digital supply voltage, DVDD
3
3.3
3.6
V
Analog supply voltage, AVDD
3
3.3
3.6
V
High-level input voltage, VIH
CMOS inputs
0.7 VCC
Low-level input voltage, VIL
CMOS inputs
0
0.2 VCC
V
Input voltage, VI
CMOS inputs
0
DVDD
V
Output voltage, VO
CMOS inputs
0
DVDD
Input transition time, tt (tr and tf, 10% to 90%)
V
0
6
V
ns
3.3 Electrical Characteristics Over Recommended Operating Conditions (unless
otherwise noted)
PARAMETER
VOH
VOL
High-level output voltage, P3 [0-7]
VOH
VOL
High-level output voltage, P1 [0-7]
IOZ
High-impedance output current
IIL
Low level input current
Low-level
IIH
High level input current
High-level
Low-level output voltage, P3 [0-7]
Low-level output voltage, P1 [0-7]
Pullup disabled
TEST CONDITIONS
DVDD–0.5
IOH = – 8 mA
IOL = 8 mA
DVDD–0.5
IDD
(3 3 V)
Analog supply voltage AVDD (3.3
MAX
UNIT
V
0.5
V
V
0.5
V
± 20
µA
– 20
–250
VI = VIH
Enabled
Digital supply voltage DVDD (3.3 V)
TYP
VI = VIL
Enabled
Pullup disabled
MIN
IOH = – 4 mA
IOL = 4 mA
20
20
µA
µA
CPU clock 12 MHz
45.9
CPU clock 24 MHz
Suspend†
50.9
196
µA
Normal
14.7
mA
mA
Suspend
24
nA
† In this 196 µA measurement, the bulk or suspend current (190 µA) is delivered to the USB cable through PUR pin. The remaining 6 µA is
consumed by the device. As described in section 7.2.3 of USB 1.1 specification, When computing suspend current, the current from VBus through
the pull-up and pullown resistors must be included.
3–1
3.4 Timing Characteristics
3.4.1
Clock and Control Signals Over Recommended Operating Conditions
(unless otherwise noted)
MIN
MAX
UNIT
fMCLKO1
fMCLKO2
Clock frequency, MCLKO1
PARAMETER
CL = 50 pF, See Note 1
TEST CONDITIONS
1
25
MHz
Clock frequency, MCLKO2
CL = 50 pF, See Note 1
1
25
MHz
fMCLKI
tw(L)
Clock frequency, MCLKI
See Note 1
5
25
MHz
Pulse duration, XINT low
CL = 50 pF
0.2
10
µs
NOTE 1: Worst case duty cycle is 45/55.
tw(L)
XINT
Figure 3–1. External Interrupt Timing Waveform
3.4.2
USB Transceiver Signals Over Recommended Operating Conditions
(unless otherwise noted)
MIN
MAX
tr
tf
Transition rise time for DP or DM
PARAMETER
TEST CONDITIONS
4
20
ns
Transition fall time for DP or DM
4
20
ns
tRFM
VO(CRS)
Rise/fall time matching
90%
110%
1.3
2
(tr / tf) × 100
Voltage output signal crossover
DM
VO(CRS)
DP
90%
10%
tr , t f
Figure 3–2. USB Differential Driver Timing Waveform
3–2
VOH
VOL
UNIT
V
3.4.3
Codec Port Interface Signals (AC ’97 Modes), TA = 25°C, DVDD = 3.3 V, AVDD = 3.3 V
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
fBIT_CLK
Frequency, BIT_CLK
See Note 1
12.288
tcyc1
tw1(H)
Cycle time, BIT_CLK
See Note 1
81.4
Pulse duration, BIT_CLK high
See Note 1
36
40.7
45
tw1(L)
fSYNC
Pulse duration, BIT_CLK low
See Note 1
36
40.7
45
Frequency, SYNC
CL = 50 pF
48
tcyc2
tw2(H)
Cycle time, SYNC
CL = 50 pF
20.8
µs
Pulse duration, SYNC high
CL = 50 pF
1.3
µs
tw2(L)
Pulse duration, SYNC low
CL = 50 pF
19.5
µs
tpd1
Propagation delay time, BIT_CLK rising edge to SYNC, SD_OUT
and RESET
CL = 50 pF
tsu
th
MHz
ns
ns
ns
kHz
15
ns
Setup time, SD_IN to BIT_CLK falling edge
10
ns
Hold time, SD_IN from BIT_CLK falling edge
10
ns
NOTE 1: Worst case duty cycle is 45/55.
tw1(H)
tw1(L)
BIT_CLK
tcyc1
tw2(H)
tw2(L)
SYNC
tcyc2
Figure 3–3. BIT_CLK and SYNC Timing Waveforms
BIT_CLK
tpd1
SYNC, SD_OUT, RESET
tsu
th
SD_IN
Figure 3–4. SYNC, SD_IN, and SD_OUT Timing Waveforms
3–3
3.4.4
Codec Port Interface Signals (I2S Modes) Over Recommended Operating Conditions
(unless otherwise noted)
TEST CONDITIONS
fSCLK
tcyc
Frequency, SCLK
CL = 50 pF
Cycle time, SCLK
CL = 50 pF, See Note 1
tpd
tsu
Propagation delay, SCLK falling edge to LRCLK and SDOUT
CL = 50 pF
MIN
MAX
UNIT
(32)FS
1/(64)FS
(64)FS
1/(32)FS
MHz
15
Setup time, SDIN to SCLK rising edge
th
Hold time, SDIN from SCLK rising edge
NOTE 1: Worst case duty cycle is 45/55.
ns
ns
10
ns
10
ns
SCLK
tcyc
tpd
LRCLK, SD_OUT
tsu
th
SD_IN
Figure 3–5. I2S Mode Timing Waveforms
3.4.5
Codec Port Interface Signals (General-Purpose Mode) Over Recommended Operating
Conditions (unless otherwise noted)
TEST CONDITIONS
MIN
MAX
UNIT
fCSCLK
tcyc
Frequency, CSCLK
CL = 50 pF
0.125
25
MHz
Cycle time, CSCLK
CL = 50 pF, See Note 2
0.040
8
µs
tpd
tsu
Propagation delay, CSCLK to CSYNC, CDATO, CSCHNE and CRESET
CL = 50 pF
15
ns
Setup time, CDATI to CSCLK
10
ns
th
Hold time, CDATI from CSCLK
10
ns
NOTE 2: The timing waveforms in Figure 3-6 show the CSYNC, CDATO, CSCHNE, and CRESET signals generated with the rising edge of the
clock and the CDATI signal sampled with the falling edge of the clock. The edge of the clock used is programmable. However, the timing
characteristics are the same regardless of which edge of the clock is used.
CSCLK
tcyc
tpd
CSYNC, CDATO,
CSCHNE, CRESET
tsu
th
CDATI
Figure 3–6. General-Purpose Mode Timing Waveforms
3–4
3.4.6
I2C Interface Signals Over Recommended Operating Conditions
(unless otherwise noted)
PARAMETER
TEST CONDITIONS
STANDARD
MODE
FAST MODE
MIN
MAX
MIN
MAX
0
100
0
400
UNIT
fSCL
tw(H)
Frequency, SCL
tw(L)
tr
Pulse duration, SCL low
Rise time, SCL and SDA
1000
300
ns
tf
tsu1
Fall time, SCL and SDA
300
300
ns
th1
tbuf
Hold time, SCL to SDA
0
0
ns
Bus free time between stop and start condition
4.7
1.3
µs
tsu2
th2
Setup time, SCL to start condition
4.7
0.6
µs
Hold time, start condition to SCL
4
0.6
µs
tsu3
CL
Setup time, SCL to stop condition
4
0.6
µs
Pulse duration, SCL high
Setup time, SDA to SCL
4
0.6
µs
4.7
1.3
µs
250
Load capacitance for each bus line
100
400
tw(H)
tw(L)
tr
kHz
ns
400
pF
tf
SCL
tsu1
th1
SDA
Figure 3–7. SCL and SDA Timing Waveforms
SCL
tsu2
th2
tsu3
tbuf
SDA
Start Condition
Stop Condition
Figure 3–8. Start and Stop Conditions Timing Waveforms
SCL
1
2
8
9
SDA OUT
SDA IN
Figure 3–9. Acknowledge Timing Waveform
3–5
3–6
4 Application Information
27 pF
DGND
24C64
SDA GND
SCL
A2
XTAL0
6 MHz
27 pF
AGND
4.99 kΩ
100 pF
4.99 kΩ
WP
A1
VCC
A0
3.3 VD
AGND
USB_CONN
PLLFILI
XTALI
XTALO
AVSS
SCL
SDA
VREN
RESET
MCLKO2
MCLKO1
CDATO
CSCLK
VCC
1000 pF
1
VCC
2
4
D–
GND
3
5
Shield D+
6
Shield
48 47 46 45 44 43 42 41 40 39 38 37
PLLFILO
AVDD
3.3 VA
MCLKI
DVSS
1.5 kΩ
PUR
27.4 Ω
DP
27.4 Ω
DM
DVDD
47 pF
MRESET
TEST
EXTEN
RSTO
1
36
35
2
3
4
34
5
32
31
6
33
TAS1020
7
30
8
29
9
10
28
11
26
12
25
27
CDATI
CSYNC
CRESET
DVDD
CSCHNE
P1.7
P1.6
P1.5
DVSS
P1.4
P1.3
P1.2
3.3 VD
13 14 15 16 17 18 19 20 21 22 23 24
3.3 VD
P3.0
P3.1
P3.2/XINT
DV SS
P3.3
P3.4
P3.5
NC
DVDD
NC
P1.0
P1.1
47 pF
3.09 kΩ
MCLKO
1.5 kΩ
1 µF
DGND
3.3 VD
Figure 4–1. Typical TAS1020 Device Connections
4–1
4–2
Appendix A
MCU Memory and Memory-Mapped Registers
This section describes the TAS1020 MCU memory configurations and operation. In general, the MCU memory
operation is the same as the industry standard 8052 MCU.
A.1 MCU Memory Space
The TAS1020 MCU memory is organized into three individual spaces: program memory, external data memory, and
internal data memory. The total address range for the program memory and the external data memory spaces is 64K
bytes each. The total address range for the internal data memory is 256 bytes.
The read only program memory contains the instructions to be executed by the MCU. The TAS1020 uses a 8K boot
ROM as the program memory during initialization. The boot ROM program code downloads the application program
code from a nonvolatile memory (that is, EEPROM) on the peripheral PCB. The application program code is written
to an 6K RAM mapped to the external data memory space. After downloading the application program code to RAM,
the boot ROM enables the normal operating mode by setting the ROM disable (SDW) bit (refer to memory
configuration register) to enable program code execution from the 6K RAM instead of the boot ROM. In the normal
operating mode, the boot ROM is still mapped to program memory space starting at address 8000h. Refer to
Figures A–1 and A–2 for details.
The external data memory contains the data buffers for the USB end-points, the configuration blocks for the USB
end-points, the setup data packet buffer for the USB control end-point, and memory mapped registers. The data
buffers for the USB end-points, the configuration blocks for the USB end-points and the setup data packet buffer for
the USB control end-point are all implemented in RAM. The memory mapped registers used for control and status
registers are implemented in hardware with flip-flops. The data buffers for the USB end-points are a total of 1304
bytes, the configuration blocks for the USB end-points are a total of 128 bytes, the setup packet buffer for the USB
control end-point is 8 bytes, and the memory mapped registers space is 80 bytes. The total external data memory
space used for these blocks of memory is 1520 bytes. In addition to these memory blocks, a 6K (6016 bytes) RAM
is mapped to the external data memory space in the boot loader mode of operation. The 6K RAM is read/write in this
mode and is used to store the application program code during download by the boot ROM. In the normal mode of
operation, the 6K RAM is mapped to the program memory space and is read-only.
A–1
A.2 Internal Data Memory
The internal data memory space is a total of 256 bytes of RAM, which includes the 128 bytes of special function
registers (SFR) space. The internal data memory space is mapped in accordance with the industry standard 8052
MCU. The internal data memory space is mapped from 00h to FFh with the SFRs mapped from 80h to FFh. The lower
128 bytes are accessible with both direct and indirect addressing. However, the upper 128 bytes, which is the SFR
space, is only accessible with direct addressing.
Program Memory
FFFFh
External Data Memory
FFFFh
Memory Mapped Registers
(80 Bytes)
FFB0h
FFAFh
USB End-Point Configuration
Blocks and Buffer Space
(1440 Bytes)
28K - Reserved
FA10h
FA0Fh
A000h
9FFFh
Boot ROM (8K)
58K – Reserved
8000h
7FFFh
28K - Reserved
1780h
177Fh
2000h
1FFFh
Code RAM (6K)
(6016 bytes)
(Read/Write)
Boot ROM (8K)
0000h
0000h
Figure A–1. Boot Loader Mode Memory Map
A–2
Program Memory
FFFFh
External Data Memory
FFFFh
Memory Mapped Registers
(80 Bytes)
FFB0h
FFAFh
USB End-Point Configuration
Blocks and Buffer Space
(1440 Bytes)
28K - Reserved
FA10h
FA0Fh
A000h
9FFFh
Boot ROM (8K)
8000h
7FFFh
64016 bytes
26752 bytes
1780h
177Fh
Code RAM (6K)
(6016 bytes)
(Read/Write)
0000h
0000h
Figure A–2. Normal Operating Mode Memory Map
A.3 External MCU Mode Memory Space
When using an external MCU for firmware development, only the USB configuration blocks, the USB buffer space,
and the memory mapped registers are accessible by the external MCU. See Section A.4 for details. In this mode,
only address lines A0 to A10 are input to the TAS1020 device from the external MCU. Therefore, the USB buffer space
and the memory mapped registers in the external data memory space are not fully decoded since all sixteen address
lines are not available. Hence, the USB buffer space and the memory mapped registers are actually accessible at
any 2K boundary within the total 64K external data memory space of the external MCU. As a result, when using the
TAS1020 in the external MCU mode, nothing can be mapped to the external data memory space of the external MCU
except the USB buffer space and the memory mapped registers of the TAS1020 device.
A–3
A.4 USB End-Point Configuration Blocks and Data Buffers Space
A.4.1
USB End-Point Configuration Blocks
The USB end-point configuration space contains 16 blocks of 8 bytes which define configuration, buffer location,
buffer size, and data count for 16 (8 input and 8 output) USB end-points. The MCU, UBM, and DMA all have access
to these configuration blocks.
The device defines an end-point of a USB pipe by initializing the configuration block configuration byte. It defines the
location of the pipe X and Y buffers in end-point data buffer space by writing to the X buffer base address byte and
Y buffer base address byte. Base addresses are octlet (8-byte) aligned. The device sets the X and Y buffer size to
allocate fixed sized buffers for the pipe. Both X and Y buffer size must be greater than or equal to the USB packet
size associated with the end-point. If the buffer size is greater than the USB packet size, each buffer will independently
recirculate.
A.4.2
Data Buffers Space
The end-point data buffer space (1304 bytes) provides rate buffering between the USB and codecs attached to the
TAS1020. Buffers are defined in this space by base address pointers and size descriptors in the USB end-point
configuration blocks. The MCU also has access to this space.
Among the 1304 bytes of endpoint data buffer (FA10h-FF27h), the locations (FA10h-FAC7h) are used by current
TAS1020 ROM mode. If ROM code service is used,the DMA data buffer loations available for customer’s application
are limited to 1120 bytes (FAC8h-FF27h) which should be enough for applications upto 5 channels, 48 kHz sampling
rate with 16 bits per sample or 3 channels, 48 kHz sampling rate with 24 bits per sample.
The UBM associates USB end-points with buffers in the end-point data buffer space by looking up configuration for
an end-point in USB end-point configuration space. A particular DMA channel is associated with a buffer through an
end-point number in the DMA channel’s control register.
External Data Memory
FFFFh
Memory Mapped Registers
(80 Bytes)
FFB0h
FFAFh
End-Point Configuration Blocks
(128 Bytes)
DMA Access
FF30h
FF2Fh
MCU Access
UBM Access
Setup Data Packet Buffer
(8 Bytes)
FF28h
FF27h
End-Point Data Buffers
(1304 Bytes)
DMA Access
FA10h
Figure A–3. USB End-Point Configuration Blocks and Buffer Space Memory Map
A–4
Table A–1. USB End-Point Configuration Blocks Address Map
ADDRESS
MNEMONIC
NAME
FFAFh
OEPDCNTY0
Out end-point 0 - Y buffer data count byte
FFAEh
Reserved
Reserved for future use
FFADh
OEPBBAY0
Out end-point 0 - Y buffer base address byte
FFACh
Reserved
Reserved for future use
FFABh
OEPDCNTX0
Out end-point 0 - X buffer data count byte
FFAAh
OEPBSIZ0
Out end-point 0 - X and Y buffer size byte
FFA9h
OEPBBAX0
Out end-point 0 - X buffer base address byte
FFA8h
OEPCNF0
Out end-point 0 – configuration byte
FFA7h
OEPDCNTY1
Out end-point 1 - Y buffer data count byte
FFA6h
Reserved
Reserved for future use
FFA5h
OEPBBAY1
Out end-point 1 - Y buffer base address byte
FFA4h
Reserved
Reserved for future use
FFA3h
OEPDCNTX1
Out end-point 1 - X buffer data count byte
FFA2h
OEPBSIZ1
Out end-point 1 - X and Y buffer size byte
FFA1h
OEPBBAX1
Out end-point 1 - X buffer base address byte
FFA0h
OEPCNF1
Out end-point 1 – configuration byte
FF9Fh
OEPDCNTY2
Out end-point 2 - Y buffer data count byte
FF9Eh
Reserved
Reserved for future use
FF9Dh
OEPBBAY2
Out end-point 2 - Y buffer base address byte
FF9Ch
Reserved
Reserved for future use
FF9Bh
OEPDCNTX2
Out end-point 2 - X buffer data count byte
FF9Ah
OEPBSIZ2
Out end-point 2 - X and Y buffer size byte
FF99h
OEPBBAX2
Out end-point 2 - X buffer base address byte
FF98h
OEPCNF2
Out end-point 2 – configuration byte
FF97h
OEPDCNTY3
Out end-point 3 - Y buffer data count byte
FF96h
Reserved
Reserved for future use
FF95h
OEPBBAY3
Out end-point 3 - Y buffer base address byte
FF94h
Reserved
Reserved for future use
FF93h
OEPDCNTX3
Out end-point 3 - X buffer data count byte
FF92h
OEPBSIZ3
Out end-point 3 - X and Y buffer size byte
FF91h
OEPBBAX3
Out end-point 3 - X buffer base address byte
FF90h
OEPCNF3
Out end-point 3 – configuration byte
FF8Fh
OEPDCNTY4
Out end-point 4 - Y buffer data count byte
FF8Eh
Reserved
Reserved for future use
FF8Dh
OEPBBAY4
Out end-point 4 - Y buffer base address byte
FF8Ch
Reserved
Reserved for future use
FF8Bh
OEPDCNTX4
Out end-point 4 - X buffer data count byte
FF8Ah
OEPBSIZ4
Out end-point 4 - X and Y buffer size byte
FF89h
OEPBBAX4
Out end-point 4 - X buffer base address byte
FF88h
OEPCNF4
Out end-point 4 – configuration byte
FF87h
OEPDCNTY5
Out end-point 5 - Y buffer data count byte
FF86h
Reserved
Reserved for future use
FF85h
OEPBBAY5
Out end-point 5 - Y buffer base address byte
FF84h
Reserved
Reserved for future use
FF83h
OEPDCNTX5
Out end-point 5 - X buffer data count byte
FF82h
OEPBSIZ5
Out end-point 5 - X and Y buffer size byte
FF81h
OEPBBAX5
Out end-point 5 - X Buffer Base Address Byte
FF80h
OEPCNF5
Out end-point 5 – configuration byte
A–5
Table A–1. USB End-Point Configuration Blocks Address Map (Continued)
ADDRESS
A–6
MNEMONIC
NAME
FF7Fh
OEPDCNTY6
Out end-point 6 - Y buffer data count byte
FF7Eh
Reserved
Reserved for future use
FF7Dh
OEPBBAY6
Out end-point 6 - Y buffer base address byte
FF7Ch
Reserved
Reserved for future use
FF7Bh
OEPDCNTX6
Out end-point 6 - X buffer data count byte
FF7Ah
OEPBSIZ6
Out end-point 6 - X and Y buffer size byte
FF79h
OEPBBAX6
Out end-point 6 - X buffer base address byte
FF78h
OEPCNF6
Out end-point 6 – configuration byte
FF77h
OEPDCNTY7
Out end-point 7 - Y buffer data count byte
FF76h
Reserved
Reserved for future use
FF75h
OEPBBAY7
Out end-point 7 - Y buffer base address byte
FF74h
Reserved
Reserved for future use
FF73h
OEPDCNTX7
Out end-point 7 - X buffer data count byte
FF72h
OEPBSIZ7
Out end-point 7 - X and Y buffer size byte
FF71h
OEPBBAX7
Out end-point 7 - X buffer base address byte
FF70h
OEPCNF7
Out end-point 7 – configuration byte
FF6Fh
IEPDCNTY0
In end-point 0 - Y buffer data count byte
FF6Eh
Reserved
Reserved for future use
FF6Dh
IEPBBAY0
In end-point 0 - Y buffer base address byte
FF6Ch
Reserved
Reserved for future use
FF6Bh
IEPDCNTX0
In end-point 0 - X buffer data count byte
FF6Ah
IEPBSIZ0
In end-point 0 - X and Y buffer size byte
FF69h
IEPBBAX0
In end-point 0 - X buffer base address byte
FF68h
IEPCNF0
In end-point 0 – configuration byte
FF67h
IEPDCNTY1
In end-point 1 - Y buffer data count byte
FF66h
Reserved
Reserved for future use
FF65h
IEPBBAY1
In end-point 1 - Y buffer base address byte
FF64h
Reserved
Reserved for future use
FF63h
IEPDCNTX1
In end-point 1 - X buffer data count byte
FF62h
IEPBSIZ1
In end-point 1 - X and Y buffer size byte
FF61h
IEPBBAX1
In end-point 1 - X buffer base address byte
FF60h
IEPCNF1
In end-point 1 – configuration byte
FF5Fh
IEPDCNTY2
In end-point 2 - Y buffer data count byte
FF5Eh
Reserved
Reserved for future use
FF5Dh
IEPBBAY2
In end-point 2 - Y buffer base address byte
FF5Ch
Reserved
Reserved for future use
FF5Bh
IEPDCNTX2
In end-point 2 - X buffer data count byte
FF5Ah
IEPBSIZ2
In end-point 2 - X and Y buffer size byte
FF59h
IEPBBAX2
In end-point 2 - X buffer base address byte
FF58h
IEPCNF2
In end-point 2 – configuration byte
FF57h
IEPDCNTY3
In end-point 3 - Y buffer data count byte
FF56h
Reserved
Reserved for future use
FF55h
IEPBBAY3
In end-point 3 - Y buffer base address byte
FF54h
Reserved
Reserved for future use
FF53h
IEPDCNTX3
In end-point 3 - X buffer data count byte
FF52h
IEPBSIZ3
In end-point 3 - X and Y buffer size byte
FF51h
IEPBBAX3
In end-point 3 - X buffer base address byte
FF50h
IEPCNF3
In end-point 3 – configuration byte
Table A–1. USB End-Point Configuration Blocks Address Map (Continued)
ADDRESS
MNEMONIC
NAME
FF4Fh
IEPDCNTY4
In end-point 4 - Y buffer data count byte
FF4Eh
Reserved
Reserved for future use
FF4Dh
IEPBBAY4
In end-point 4 - Y buffer base address byte
FF4Ch
Reserved
Reserved for future use
FF4Bh
IEPDCNTX4
In end-point 4 - X buffer data count byte
FF4Ah
IEPBSIZ4
In end-point 4 - X and Y buffer size byte
FF49h
IEPBBAX4
In end-point 4 - X buffer base address byte
FF48h
IEPCNF4
In end-point 4 – configuration byte
FF47h
IEPDCNTY5
In end-point 5 - Y buffer data count byte
FF46h
Reserved
Reserved for future use
FF45h
IEPBBAY5
In end-point 5 - Y buffer base address byte
FF44h
Reserved
Reserved for future use
FF43h
IEPDCNTX5
In end-point 5 - X buffer data count byte
FF42h
IEPBSIZ5
In end-point 5 - X and Y buffer size byte
FF41h
IEPBBAX5
In end-point 5 - X buffer base address byte
FF40h
IEPCNF5
In end-Point 5 – configuration byte
FF3Fh
IEPDCNTY6
In end-point 6 - Y buffer data count byte
FF3Eh
Reserved
Reserved for future use
FF3Dh
IEPBBAY6
In end-point 6 - Y buffer base address byte
FF3Ch
Reserved
Reserved for future use
FF3Bh
IEPDCNTX6
In end-point 6 - X buffer data count byte
FF3Ah
IEPBSIZ6
In end-point 6 - X and Y buffer size byte
FF39h
IEPBBAX6
In end-point 6 - X buffer base address byte
FF38h
IEPCNF6
In end-point 6 – configuration byte
FF37h
IEPDCNTY7
In end-point 7 - Y buffer data count byte
FF36h
Reserved
Reserved for future use
FF35h
IEPBBAY7
In end-point 7 - Y buffer base address byte
FF34h
Reserved
Reserved for future use
FF33h
IEPDCNTX7
In end-point 7 - X buffer data count byte
FF32h
IEPBSIZ7
In end-point 7 - X and Y buffer size byte
FF31h
IEPBBAX7
In end-point 7 - X buffer base address byte
FF30h
IEPCNF7
In end-point 7 – configuration byte
A–7
A.4.3
USB Out End-Point Configuration Bytes
This section describes the individual bytes in the USB end-point configuration blocks for the out end-points. A set of
8 bytes is used for the control and operation of each USB out end-point. In addition to the USB control end-point, the
TAS1020 supports up to a total of seven out end-points.
A.4.3.1 USB Out End-Point – Y Buffer Data Count Byte (OEPDCNTYx)
The USB out end-point Y buffer data count byte contains the 7-bit value used to specify the amount of data received
in a data packet from the host PC. The no acknowledge status bit is also contained in this byte.
Bit
Mnemonic
7
6
5
4
3
2
1
0
NACK
DCNTY6
DCNTY5
DCNTY4
DCNTY3
DCNTY2
DCNTY1
DCNTY0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Type
BIT
7
6:0
MNEMONIC
NAME
DESCRIPTION
NACK
No acknowledge
The no acknowledge status bit is set to a 1 by the UBM at the end of a successful USB out
transaction to this end-point to indicate that the USB end-point Y buffer contains a valid data
packet and that the Y buffer data count value is valid. For control, interrupt, or bulk end-points,
when this bit is set to a 1, all subsequent transactions to the end-point will result in a NACK
handshake response to the host PC. Also for control, interrupt, and bulk end-points to enable
this end-point to receive another data packet from the host PC, this bit must be cleared to a 0 by
the MCU. For isochronous end-points, a NACK handshake response to the host PC is not allowed. Therefore, the UBM ignores this bit in reference to receiving the next data packet. However, the MCU or DMA must clear this bit before reading the data packet from the buffer.
DCNTY(6:0)
Y Buffer data count
The Y buffer data count value is set by the UBM when a new data packet is written to the Y
buffer for the out end-point. The 7-bit value is set to the number of bytes in the data packet for
control, interrupt or bulk end-point transfers and is set to the number of samples in the data
packet for isochronous end-point transfers. To determine the number of samples in the data
packet for isochronous transfers, the bytes per sample value in the configuration byte is used.
The data count value is read by the MCU or DMA to obtain the data packet size.
A.4.3.2 USB Out End-Point – Y Buffer Base Address Byte (OEPBBAYx)
The USB out end-point Y buffer base address byte contains the 8-bit value used to specify the base memory location
for the Y data buffer for a particular USB out end-point.
Bit
Mnemonic
Type
7
6
5
4
3
2
1
0
BBAY10
BBAY9
BBAY8
BBAY7
BBAY6
BBAY5
BBAY4
BBAY3
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
BIT
MNEMONIC
7:0
BBAY(10:3)
A–8
NAME
Y Buffer base address
DESCRIPTION
The Y buffer base address value is set by the MCU to program the base address location in
memory to be used for the Y data buffer. A total of 11 bits is used to specify the base address
location. This byte specifies the most significant 8 bits of the address. All 0s are used by the
hardware for the three least significant bits.
A.4.3.3 USB Out End-Point – X Buffer Data Count Byte (OEPDCNTXx)
The USB out end-point X buffer data count byte contains the 7-bit value used to specify the amount of data received
in a data packet from the host PC. The no acknowledge status bit is also contained in this byte.
Bit
Mnemonic
7
6
5
4
3
2
1
0
NACK
DCNTX6
DCNTX5
DCNTX4
DCNTX3
DCNTX2
DCNTX1
DCNTX0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Type
BIT
7
6:0
MNEMONIC
NAME
DESCRIPTION
NACK
No acknowledge
The no acknowledge status bit is set to a 1 by the UBM at the end of a successful USB out
transaction to this end-point to indicate that the USB end-point X buffer contains a valid data
packet and that the X buffer data count value is valid. For control, interrupt, or bulk end-points,
when this bit is set to a 1, all subsequent transactions to the end-point will result in a NACK
handshake response to the host PC. Also for control, interrupt, and bulk end-points to enable
this end-point to receive another data packet from the host PC, this bit must be cleared to a 0
by the MCU. For isochronous end-points, a NACK handshake response to the host PC is not
allowed. Therefore, the UBM ignores this bit in reference to receiving the next data packet.
However, the MCU or DMA must clear this bit before reading the data packet from the buffer.
DCNTX(6:0)
X Buffer data count
The X buffer data count value is set by the UBM when a new data packet is written to the X
buffer for the out end-point. The 7-bit value is set to the number of bytes in the data packet for
control, interrupt, or bulk end-point transfers and is set to the number of samples in the data
packet for isochronous end-point transfers. To determine the number of samples in the data
packet for isochronous transfers, the bytes per sample value in the configuration byte is
used. The data count value is read by the MCU or DMA to obtain the data packet size.
A.4.3.4 USB Out End-Point – X and Y Buffer Size Byte (OEPBSIZx)
The USB out end-point X and Y buffer size byte contains the 8-bit value used to specify the size of the two data buffers
to be used for this end-point.
Bit
Mnemonic
7
6
5
4
3
2
1
0
BSIZ7
BSIZ6
BSIZ5
BSIZ4
BSIZ3
BSIZ2
BSIZ1
BSIZ0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Type
BIT
7:0
MNEMONIC
NAME
BSIZ(7:0)
Buffer size
DESCRIPTION
The X and Y buffer size value is set by the MCU to program the size of the X and Y data packet
buffers. Both buffers are programmed to the same size based on this value. This value is in
8-byte units. For example, a value of 18h results in the size of the X and Y buffers each being
set to 192 bytes.
A.4.3.5 USB Out End-Point – X Buffer Base Address Byte (OEPBBAXx)
The USB out end-point X buffer base address byte contains the 8-bit value used to specify the base memory location
for the X data buffer for a particular USB out end-point.
Bit
Mnemonic
7
6
5
4
3
2
1
0
BBAX10
BBAX9
BBAX8
BBAX7
BBAX6
BBAX5
BBAX4
BBAX3
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Type
BIT
7:0
MNEMONIC
BBAX(10:3)
NAME
DESCRIPTION
X Buffer base address
The X buffer base address value is set by the MCU to program the base address location in
memory to be used for the X data buffer. A total of 11 bits is used to specify the base address
location. This byte specifies the most significant 8 bits of the address. All 0s are used by the
hardware for the three least significant bits.
A.4.3.6 USB Out End-Point – Configuration Byte (OEPCNFx)
The USB out end-point configuration byte contains the various bits used to configure and control the end-point. Note
that the bits in this byte take on different functionality based on the type of end-point defined. The control, interrupt,
and bulk end-points function differently than the isochronous end-points.
A–9
A.4.3.6.1 USB Out End-Point – Control, Interrupt or Bulk configuration byte
This section defines the functionality of the bits in the USB out end-point configuration byte for control, interrupt, and
bulk end-points.
Bit
Mnemonic
Type
BIT
7
6
5
4
3
2
1
0
OEPEN
ISO
TOGGLE
DBUF
STALL
OEPIE
—
—
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
MNEMONIC
NAME
DESCRIPTION
7
OEPEN
End-Point enable
The end-point enable bit is set to a 1 by the MCU to enable the out end-point.
6
ISO
Isochronous end-point
The isochronous end-point bit is set to a 1 by the MCU to specify the use of a particular out
end-point for isochronous transactions. This bit must be cleared to a ’0’ by the MCU to use a
particular out end-point for control, interrupt, or bulk transactions.
5
TOGGLE
Toggle
The toggle bit is controlled by the UBM and is toggled at the end of a successful out data
stage transaction if a valid data packet is received and the data packet PID matches the
expected PID.
4
DBUF
Double buffer mode
The double buffer mode bit is set to a 1 by the MCU to enable the use of both the X and Y
data packet buffers for USB transactions to a particular out end-point. This bit must be
cleared to a 0 by the MCU to use the single buffer mode. In the single buffer mode, only the X
buffer is used.
3
STALL
Stall
The stall bit is set to a ’1’ by the MCU to stall end-point transactions. When this bit is set, the
hardware will automatically return a stall handshake to the host PC for any transaction
received for the end-point. An exception is the control end-point setup stage transaction,
which must always be received. This requirement allows a Clear_Feature_Stall request to
be received from the host PC. Control end-point data and status stage transactions
however can be stalled. The stall bit is cleared to a ’0’ by the MCU if a Clear_Feature_Stall
request or a USB reset is received from the host PC. For a control write transaction, if the
amount of data received is greater than expected, the UBM will set the stall bit to a 1 to stall
the end-point. When the stall bit is set to a 1 by the UBM, the USB out end-point 0 interrupt
will be generated.
2
OEPIE
Interrupt enable
The interrupt enable bit is set to a 1 by the MCU to enable the out end-point interrupt. See
section A.5.7.1 for details on the out end-point interrupts.
—
Reserved
Reserved for future use
1:0
A–10
A.4.3.6.2 USB Out End-Point – Isochronous Configuration Byte
This section defines the functionality of the bits in the USB out end-point configuration byte for isochronous
end-points.
Bit
7
Mnemonic
6
5
4
3
2
1
0
OEPEN
ISO
OVF
BPS4
BPS3
BPS2
BPS1
BPS0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Type
BIT
MNEMONIC
NAME
DESCRIPTION
7
OEPEN
End-Point enable
The end-point enable bit is set to a 1 by the MCU to enable the out end-point.
6
ISO
Isochronous end-point
The isochronous end-point bit is set to a 1 by the MCU to specify the use of a particular out
end-point for isochronous transactions. This bit must be cleared to a 0 by the MCU for a
particular out end-point to be used for control, interrupt, or bulk transactions.
5
OVF
Overflow
The overflow bit is set to a 1 by the UBM to indicate a buffer overflow condition has occurred.
This bit is used for diagnostic purposes only and is not used for normal operation. This bit
can only be cleared to a 0 by the MCU.
BPS(4:0)
Bytes per sample
The bytes per sample bits are used to define the number of bytes per isochronous data
sample. In other words, the total number of bytes in an entire audio codec frame. For
example, a PCM 16-bit stereo audio data sample consists of 4 bytes. There are two bytes of
left channel data and two bytes of right channel data. For a four channel system using 16-bit
data, the total number of bytes is 8, which is the isochronous data sample size.
00h = 1 byte, 01h = 2 bytes, …, 1Fh = 32 bytes
4:0
A.4.4
USB In End-Point Configuration Bytes
This section describes the individual bytes in the USB end-point configuration blocks for the in end-points. A set of
8 bytes is used for the control and operation of each USB in end-point. In addition to the USB control end-point, the
TAS1020 supports up to a total of seven in end-points.
A.4.4.1 USB In End-Point – Y Buffer Data Count Byte (IEPDCNTYx)
The USB in end-point Y buffer data count byte contains the 7-bit value used to specify the amount of data to be
transmitted in a data packet to the host PC. The no acknowledge status bit is also contained in this byte.
Bit
Mnemonic
7
6
5
4
3
2
1
0
NACK
DCNTY6
DCNTY5
DCNTY4
DCNTY3
DCNTY2
DCNTY1
DCNTY0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Type
BIT
7
6:0
MNEMONIC
NAME
DESCRIPTION
NACK
No acknowledge
The no acknowledge status bit is set to a 1 by the UBM at the end of a successful USB in
transaction to this end-point to indicate that the USB end-point Y buffer is empty. For
control, interrupt, or bulk end-points, when this bit is set to a 1, all subsequent transactions
to the end-point will result in a NACK handshake response to the host PC. Also for control,
interrupt, and bulk end-points to enable this end-point to transmit another data packet to the
Host PC, this bit must be cleared to a 0 by the MCU. For isochronous end-points, a NACK
handshake response to the host PC is not allowed. Therefore, the UBM ignores this bit in
reference to sending the next data packet. However, the MCU or DMA must clear this bit
after writing a data packet to the buffer.
DCNTY(6:0)
Y Buffer data count
The Y buffer data count value is set by the MCU or DMA when a new data packet is written
to the Y buffer for the in end-point. The 7-bit value is set to the number of bytes in the data
packet for control, interrupt, or bulk end-point transfers and is set to the number of samples
in the data packet for isochronous end-point transfers. To determine the number of samples
in the data packet for isochronous transfers, the bytes per sample value in the configuration
byte is used.
A–11
A.4.4.2 USB In End-Point – Y Buffer Base Address Byte (IEPBBAYx)
The USB in end-point Y buffer base address byte contains the 8-bit value used to specify the base memory location
for the Y data buffer for a particular USB in end-point.
Bit
Mnemonic
7
6
5
4
3
2
1
0
BBAY10
BBAY9
BBAY8
BBAY7
BBAY6
BBAY5
BBAY4
BBAY3
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Type
BIT
7:0
MNEMONIC
NAME
BBAY(10:3)
Y Buffer base address
DESCRIPTION
The Y buffer base address value is set by the MCU to program the base address location in
memory to be used for the Y data buffer. A total of 11 bits is used to specify the base address
location. This byte specifies the most significant 8 bits of the address. All 0s are used by the
hardware for the three least significant bits.
A.4.4.3 USB In End-Point – X Buffer Data Count Byte (IEPDCNTXx)
The USB in end-point X buffer data count byte contains the 7-bit value used to specify the amount of data received
in a data packet from the host PC. The no acknowledge status bit is also contained in this byte.
Bit
Mnemonic
7
6
5
4
3
2
1
0
NACK
DCNTX6
DCNTX5
DCNTX4
DCNTX3
DCNTX2
DCNTX1
DCNTX0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Type
BIT
7
6:0
MNEMONIC
NAME
DESCRIPTION
NACK
No acknowledge
The no acknowledge status bit is set to a 1 by the UBM at the end of a successful USB in
transaction to this end-point to indicate that the USB end-point X buffer is empty. For
control, interrupt, or bulk end-points, when this bit is set to a 1, all subsequent transactions
to the end-point will result in a NACK handshake response to the host PC. Also for control,
interrupt, and bulk end-points to enable this end-point to transmit another data packet to the
host PC, this bit must be cleared to a 0 by the MCU. For isochronous end-points, a NACK
handshake response to the host PC is not allowed. Therefore, the UBM ignores this bit in
reference to sending the next data packet. However, the MCU or DMA must clear this bit
after writing a data packet to the buffer.
DCNTX(6:0)
X Buffer data count
The X buffer data count value is set by the MCU or DMA when a new data packet is written
to the X buffer for the in end-point. The 7-bit value is set to the number of bytes in the data
packet for control, interrupt, or bulk end-point transfers and is set to the number of samples
in the data packet for isochronous end-point transfers. To determine the number of samples
in the data packet for isochronous transfers, the bytes per sample value in the configuration
byte is used.
A.4.4.4 USB In End-Point – X and Y Buffer Size Byte (IEPBSIZx)
The USB in end-point X and Y buffer size byte contains the 8-bit value used to specify the size of the two data buffers
to be used for this end-point.
Bit
Mnemonic
Type
BIT
7
A–12
7
6
5
4
3
2
1
0
BSIZ7
BSIZ6
BSIZ5
BSIZ4
BSIZ3
BSIZ2
BSIZ1
BSIZ0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
MNEMONIC
BSIZ(7:0)
NAME
Buffer size
DESCRIPTION
The X and Y buffer size value is set by the MCU to program the size of the X and Y data
packet buffers. Both buffers are programmed to the same size based on this value. This
value should be in 8 byte units. For example, a value of 18h results in the size of the X and Y
buffers each being set to 192 bytes.
A.4.4.5 SB In End-Point – X Buffer Base Address Byte (IEPBBAXx)
The USB in end-point X buffer base address byte contains the 8-bit value used to specify the base memory location
for the X data buffer for a particular USB in end-point.
Bit
Mnemonic
7
6
5
4
3
2
1
0
BBAX10
BBAX9
BBAX8
BBAX7
BBAX6
BBAX5
BBAX4
BBAX3
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Type
BIT
7:0
MNEMONIC
NAME
BBAX(10:3)
X Buffer base address
DESCRIPTION
The X buffer base address value is set by the MCU to program the base address location in
memory to be used for the X data buffer. A total of 11 bits is used to specify the base address
location. This byte specifies the most significant 8 bits of the address. All 0s are used by the
hardware for the three least significant bits.
A.4.4.6 USB In End-Point – Configuration Byte (IEPCNFx)
The USB in end-point configuration byte contains the various bits used to configure and control the end-point. Note
that the bits in this byte take on different functionality based on the type of end-point defined. Basically, the control,
interrupt and bulk end-points function differently than the isochronous end-points.
A.4.4.6.1 USB In End-Point – Control, Interrupt or Bulk Configuration Byte
This section defines the functionality of the bits in the USB in end-point configuration byte for control, interrupt, and
bulk end-points.
Bit
Mnemonic
Type
BIT
7
6
5
4
3
2
1
0
IEPEN
ISO
TOGGLE
DBUF
STALL
IEPIE
—
—
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
MNEMONIC
NAME
DESCRIPTION
7
IEPEN
End-Point enable
The end-point enable bit is set to a 1 by the MCU to enable the in end-point. This bit does not
affect the reception of the control end-point setup stage transaction.
6
ISO
Isochronous end-point
The isochronous end-point bit is set to a 1 by the MCU to specify the use of a particular in
end-point for isochronous transactions. This bit must be cleared to a 0 by the MCU to use a
particular in end-point for control, interrupt, or bulk transactions.
5
TOGGLE
Toggle
The toggle bit is controlled by the UBM and is toggled at the end of a successful in data
stage transaction if a valid data packet is transmitted. If this bit is a 0, a DATA0 PID is
transmitted in the data packet to the host PC. If this bit is a 1, a DATA1 PID is transmitted in
the data packet.
4
DBUF
Double buffer mode
The double buffer mode bit is set to a 1 by the MCU to enable the use of both the X and Y
data packet buffers for USB transactions to a particular in end-point. This bit must be
cleared to a 0 by the MCU to use the single buffer mode. In the single buffer mode, only the X
buffer is used.
3
STALL
Stall
The stall bit is set to a 1 by the MCU to stall end-point transactions. When this bit is set, the
hardware will automatically return a stall handshake to the host PC for any transaction
received for the end-point.
2
IEPIE
Interrupt enable
The interrupt enable bit is set to a 1 by the MCU to enable the in end-point interrupt. See
section A.5.7.2 for details on the in end-point interrupts.
—
Reserved
Reserved for future use.
1:0
A–13
A.4.4.6.1 USB In End-Point – Isochronous Configuration Byte
This section defines the functionality of the bits in the USB in end-point configuration byte for isochronous end-points.
Bit
Mnemonic
Type
BIT
7
6
5
4
3
2
1
0
IEPEN
ISO
OVF
BPS4
BPS3
BPS2
BPS1
BPS0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
MNEMONIC
NAME
DESCRIPTION
7
IEPEN
End-Point enable
The end-point enable bit is set to a 1 by the MCU to enable the in end-point.
6
ISO
Isochronous end-point
The isochronous end-point bit is set to a 1 by the MCU to specify the use of a particular in
end-point for isochronous transactions. This bit must be cleared to a 0 by the MCU for a
particular in end-point to be used for control, interrupt, or bulk transactions.
5
OVF
Overflow
The overflow bit is set to a 1 by the UBM to indicate a buffer overflow condition has occurred.
This bit is used for diagnostic purposes only and is not used for normal operation. This bit
can only be cleared to a 0 by the MCU.
4:0
BPS(4:0)
Bytes per sample
The bytes per sample bits are used to define the number of bytes per isochronous data
sample. In other words, the total number of bytes in an entire audio codec frame. For
example, a PCM 16-bit stereo audio data sample consists of 4 bytes. There are two bytes of
left channel data and two bytes of right channel data. For a four channel system using 16-bit
data, the total number of bytes is 8, which is the isochronous data sample size.
00h = 1 byte, 01h = 2 bytes, …, 1Fh = 32 bytes
A.4.5
USB Control End-Point Setup Stage Data Packet Buffer
The USB control end-point setup stage data packet buffer is the buffer space used to store the 8-byte data packet
received from the host PC during a control end-point transfer setup stage transaction. Refer to Chapter 9 of the USB
Specification for details on the data packet.
Table A–2. USB Control End-Point Setup Data Packet Buffer Address Map
ADDRESS
A–14
NAME
FF2Fh
wLength – Number of bytes to transfer in the data stage
FF2Eh
wLength – Number of bytes to transfer in the data stage
FF2Dh
wIndex – Index or offset value
FF2Ch
wIndex – Index or offset value
FF2Bh
wValue – Value of a parameter specific to the request
FF2Ah
wValue – Value of a parameter specific to the request
FF29h
bRequest – Specifies the particular request
FF28h
bmRequestType – Identifies the characteristics of the request
A.5 Memory-Mapped Registers
The TAS1020 device provides a set of control and status registers to be used by the MCU to control the overall
operation of the device. This section describes the memory-mapped registers.
Table A–3. Memory Mapped Registers Address Map
ADDRESS
MNEMONIC
NAME
SECTION
PAGE
FFFFh
USBFADR
USB function address register
A.5.1.1
A–17
FFFEh
USBSTA
USB status register
A.5.1.2
A–18
FFFDh
USBIMSK
USB interrupt mask register
A.5.1.3
A–19
FFFCh
USBCTL
USB control register
A.5.1.4
A–19
FFFBh
USBFNL
USB frame number register (low-byte)
A.5.1.5
A–20
FFFAh
USBFNH
USB frame number register (high-byte)
A.5.1.6
A–20
FFF9h
ACG2FRQ0
Adaptive clock generator2 frequency register (Byte 0)
A.5.3.6
A–25
FFF8h
ACG2FRQ1
Adaptive clock generator2 frequency register (Byte 1)
A.5.3.7
A–25
FFF7h
ACG2FRQ2
Adaptive clock generator2 frequency register (Byte 2)
A.5.3.8
A–26
FFF6h
ACG2DCTL
Adaptive clock generator2 divider control register
A.5.3.9
A–26
FFF5h
Reserved
Reserved for future use
FFF4h
DMABCNT1H
DMA buffer content register (high-byte) (channel 1)
A.5.2.5
A–22
FFF3h
DMABCNT1L
DMA buffer content register (low-byte) (channel 1)
A.5.2.4
A–21
FFF2h
DMABPCT0
DMA bulk packet count register (low-byte)
A.5.2.6
A–22
FFF1h
DMABPCT1
DMA bulk packet count register (high-byte)
A.5.2.7
A–22
FFF0h
DMATSL1
DMA time slot assignment register (low-byte) (channel 1)
A.5.2.1
A–20
FFEFh
DMATSH1
DMA time slot assignment register (high-byte) (channel 1)
A.5.2.2
A–21
FFEEh
DMACTL1
DMA control register (channel 1)
A.5.2.3
A–21
FFEDh
Reserved
Reserved for future use
FFECh
DMABCNT0H
DMA current buffer content register (high-byte) (channel 0)
A.5.2.5
A–22
FFEBh
DMABCNT0L
DMA current buffer content register (low-byte) (channel 0)
A.5.2.4
A–21
FFEAh
DMATSL0
DMA time slot assignment register (low-byte) (channel 0)
A.5.2.1
A–20
FFE9h
DMATSH0
DMA time slot assignment register (high-byte) (channel 0)
A.5.2.2
A–21
FFE8h
DMACTL0
DMA control register (channel 0)
A.5.2.3
A–21
FFE7h
ACG1FRQ0
Adaptive clock generator1 frequency register (byte 0)
A.5.3.1
A–24
FFE6h
ACG1FRQ1
Adaptive clock generator1 frequency register (byte 1)
A.5.3.2
A–24
FFE5h
ACG1FRQ2
Adaptive clock generator1 frequency register (byte 2)
A.5.3.3
A–24
FFE4h
ACGCAPL
Adaptive clock generator1 MCLK capture register (low byte)
A.5.3.4
A–25
FFE3h
ACGCAPH
Adaptive clock generator1 MCLK capture register (high byte)
A.5.3.5
A–25
FFE2h
ACG1DCTL
Adaptive clock generator1 divider control register
A.5.3.10
A–26
FFE1h
ACGCTL
Adaptive clock generator control register
A.5.3.11
A–27
FFE0h
CPTCNF1
Codec port interface configuration register 1
A.5.4.1
A–27
FFDFh
CPTCNF2
Codec port interface configuration register 2
A.5.4.2
A–28
FFDEh
CPTCNF3
Codec port interface configuration register 3
A.5.4.3
A–29
FFDDh
CPTCNF4
Codec port interface configuration register 4
A.5.4.4
A–30
FFDCh
CPTCTL
Codec port interface control and status register
A.5.4.5
A–31
FFDBh
CPTADR
Codec port interface address register
A.5.4.6
A–32
FFDAh
CPTDATL
Codec port interface data register (low-byte)
A.5.4.7
A–32
FFD9h
CPTDATH
Codec port interface data register (high-byte)
A.5.4.8
A–33
FFD8h
CPTVSLL
Codec port interface valid slots register (low-byte)
A.5.4.9
A–33
FFD7h
CPTVSLH
Codec port interface valid slots register (high-byte)
A.5.4.10
A–34
A–15
Table A–3. Memory-Mapped Registers Address Map (Continued)
ADDRESS
MNEMONIC
NAME
SECTION
PAGE
FFD6h
CPTRXCNF2
Codec port interface receive configuration register 2
A.5.4.11
A–34
FFD5h
CPTRXCNF3
Codec port interface receive configuration register 3
A.5.4.12
A–35
FFD4h
CPTRXCNF4
Codec port interface receive configuration register 4
A.5.4.13
A–36
FFD3h
Reserved
Reserved for future use
FFD2h
Reserved
Reserved for future use
FFD1h
Reserved
Reserved for future use
FFD0h
Reserved
Reserved for future use
FFCFh
Reserved
Reserved for future use
FFCEh
Reserved
Reserved for future use
FFCDh
Reserved
Reserved for future use
FFCCh
Reserved
Reserved for future use
FFCBh
Reserved
Reserved for future use
FFCAh
P3MSK
Mask register for P3
A.5.5.1
A–36
FFC9h
Reserved
Reserved for future use
FFC8h
Reserved
Reserved for future use
FFC7h
Reserved
Reserved for future use
FFC6h
Reserved
Reserved for future use
FFC5h
Reserved
Reserved for future use
FFC4h
Reserved
FFC3h
I2CADR
Reserved for future use
I2C interface address register
A.5.6.1
A–36
A.5.6.2
A–37
A.5.6.3
A–37
A.5.6.4
A–38
FFC2h
I2CDATI
FFC1h
I2CDATO
I2C interface receive data register
I2C interface transmit data register
FFC0h
I2CCTL
I2C interface control and status register
FFBFh
Reserved
Reserved for future use
FFBEh
Reserved
Reserved for future use
FFBDh
Reserved
Reserved for future use
FFBCh
Ch0WrPtrL
UBM write pointer (low-byte) (8 bits)
A.5.2.8
A–22
FFBBh
Ch0WrPtrH
UBM write pointer (high-byte) (3 bits)
A.5.2.9
A–23
FFBAh
Ch0RdPtrL
DMA read pointer (low-byte) (8 bits)
A.5.2.10
A–23
FFB9h
Ch0RdPtrH
DMA read pointer (high-byte) (3 bits)
A.5.2.11
A–23
FFB8h
Ch1WrPtrL
UBM write pointer (low-byte) (8 bits)
A.5.2.8
A–22
FFB7h
Ch1WrPtrH
UBM write pointer (high-byte) (3 bits)
A.5.2.9
A–23
FFB6h
Ch1RdPtrL
DMA read pointer (low-byte) (8 bits)
A.5.2.10
A–23
FFB5h
Ch1RdPtrH
DMA read pointer (high-byte) (3 bits)
A.5.2.11
A–23
FFB4h
OEPINT
USB out end-point interrupt register
A.5.7.1
A–39
FFB3h
IEPINT
USB in end-point interrupt register
A.5.7.2
A–39
FFB2h
VECINT
Interrupt vector register
A.5.7.3
A–40
FFB1h
GLOBCTL
Global control register
A.5.7.4
A–41
FFB0h
MEMCFG
Memory configuration register
A.5.7.5
A–41
A–16
A.5.1
USB Registers
This section describes the memory-mapped registers used for control and operation of the USB functions. This
section consists of six registers used for USB functions.
A.5.1.1 USB Function Address Register (USBFADR – Address FFFFh)
The USB function address register contains the current setting of the USB device address assigned to the function
by the host. After power-on reset or USB reset, the default address will be 00h. During enumeration of the function
by the host, the MCU should load the assigned address to this register when a USB Set_Address request is received
by the control end-point.
Bit
7
6
5
4
3
2
1
0
Mnemonic
—
FA6
FA5
FA4
FA3
FA2
FA1
FA0
Type
R
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Default
0
0
0
0
0
0
0
0
BIT
7
6:0
MNEMONIC
NAME
DESCRIPTION
—
Reserved
Reserved for future use
FA(6:0)
Function address
The function address bit values are set by the MCU to program the USB device address assigned
by the host PC.
A–17
A.5.1.2 USB Status Register (USBSTA – Address FFFEh)
The USB status register contains various status bits used for USB operations.
Bit
Mnemonic
7
6
5
4
3
2
1
0
RSTR
SUSR
RESR
SOF
PSOF
SETUP
—
STPOW
Type
R
R
R
R
R
R
R
R
Default
0
0
0
0
0
0
0
0
BIT
MNEMONIC
NAME
DESCRIPTION
7
RSTR
Function reset
The function reset bit is set to a 1 by hardware in response to the host PC initiating a USB
reset to the function. When a USB reset occurs, all of the USB logic blocks, including the
SIE, UBM, frame timer, and suspend/resume are automatically reset. The function reset
enable (FRSTE) control bit in the USB control register can be used to enable the USB reset
to reset all TAS1020 logic, except the shadow the ROM (SDW) and the USB function
connect (CONT) bits. When the FRSTE control bit is set to a 1, the reset output (RSTO)
signal from the TAS1020 device will also be active when a USB reset occurs. This bit is read
only and is cleared when the MCU writes to the interrupt vector register.
6
SUSR
Function suspend
The function suspend bit is set to a 1 by hardware when a USB suspend condition is
detected by the suspend/resume logic. See section 2.2.5 for details on the USB suspend
and resume operation. This bit is read only and is cleared when the MCU writes to the
interrupt vector register.
5
RESR
Function resume
The function resume bit is set to a 1 by hardware when a USB resume condition is detected
by the suspend/resume logic. See section 2.2.5 for details on the USB suspend and
resume operation. This bit is read only and is cleared when the MCU writes to the interrupt
vector register.
4
SOF
Start-of-frame
The start-of-frame bit is set to a 1 by hardware when a new USB frame starts. This bit is set
when the SOF packet from the host PC is detected, even if the TAS1020 frame timer is not
locked to the host PC frame timer. This bit is read only and is cleared when the MCU writes
to the interrupt vector register. The nominal SOF rate is 1 ms.
3
PSOF
Pseudo start-of-frame
The pseudo start-of-frame bit is set to a 1 by hardware when a USB pseudo SOF occurs.
The pseudo SOF is an artificial SOF signal that is generated when the TAS1020 frame timer
is not locked to the host PC frame timer. This bit is read only and is cleared when the MCU
writes to the interrupt vector register. The nominal pseudo SOF rate is 1 ms.
2
SETUP
Setup stage transaction
The setup stage transaction bit is set to a 1 by hardware when a successful control
end-point setup stage transaction is completed. Upon completion of the setup stage
transaction, the USB control end-point setup stage data packet buffer should contain a new
setup stage data packet.
1
—
Reserved
Reserved for future use
0
STPOW
Setup stage transaction
over-write
The setup stage transaction over-write bit is set to a 1 by hardware when the data in the
USB control end-point setup data packet buffer is over-written. This scenario occurs when
the host PC prematurely terminates a USB control transfer by simply starting a new control
transfer with a new setup stage transaction.
A–18
A.5.1.3 USB Interrupt Mask Register (USBMSK – Address FFFDh)
The USB interrupt mask register contains the interrupt mask bits used to enable or disable the generation of interrupts
based on the corresponding status bits.
Bit
Mnemonic
Type
7
6
5
4
3
2
1
0
RSTR
SUSR
RESR
SOF
PSOF
SETUP
—
STPOW
R/W
R/W
R/W
R/W
R/W
R/W
R
R/W
0
0
0
0
0
0
0
0
Default
BIT
MNEMONIC
NAME
DESCRIPTION
7
RSTR
Function reset
The function reset interrupt mask bit is set to a 1 by the MCU to enable the USB function
reset interrupt.
6
SUSR
Function suspend
The function suspend interrupt mask bit is set to a 1 by the MCU to enable the USB function
suspend interrupt.
5
RESR
Function resume
The function resume interrupt mask bit is set to a 1 by the MCU to enable the USB function
resume interrupt.
4
SOF
Start-of-frame
The start-of-frame interrupt mask bit is set to a 1 by the MCU to enable the USB
start-of-frame interrupt.
3
PSOF
Pseudo start-of-frame
The pseudo start-of-frame interrupt mask bit is set to a 1 by the MCU to enable the USB
pseudo start-of-frame interrupt.
2
SETUP
Setup stage transaction
The setup stage transaction interrupt mask bit is set to a 1 by the MCU to enable the USB
setup stage transaction interrupt.
1
—
Reserved
Reserved for future use
0
STPOW
Setup stage transaction
over-write
The setup stage transaction over-write interrupt mask bit is set to a 1 by the MCU to enable
the USB setup stage transaction over-write interrupt.
A.5.1.4 USB Control Register (USBCTL – Address FFFCh)
The USB control register contains various control bits used for USB operations.
Bit
Mnemonic
Type
7
6
5
4
3
2
1
0
CONT
FEN
RWUP
FRSTE
—
—
—
SDW_OK
R/W
R/W
R/W
R/W
R
R
R
R/W
0
0
0
0
0
0
0
0
Default
BIT
MNEMONIC
NAME
DESCRIPTION
7
CONT
Function connect
The function connect bit is set to 1 by the MCU to connect the TAS1020 device to the USB. As a
result of connecting to the USB, the host PC should enumerate the function. When this bit is set,
the USB data plus pullup resistor (PUR) output signal is enabled, which will connect the pullup on
the PCB to the TAS1020 3.3-V supply voltage. When this bit is cleared to 0, the PUR output is in the
3-stated. This bit is not affected by a USB reset.
6
FEN
Function enable
The function enable bit is set to 1 by the MCU to enable the TAS1020 device to respond to USB
transactions. If this bit is cleared to 0, the UBM will ignore all USB transactions. This bit is cleared
by a USB reset.
5
RWUP
Remote wake-up
The remote wake-up bit is set to 1 by the MCU to request the suspend/resume logic to generate
resume signaling upstream on the USB. This bit is used to exit a USB low-power suspend state
when a remote wake-up event occurs. After initiating the resume signaling by setting this bit, the
MCU should clear this bit within 2.5 µs.
4
FRSTE
Function reset
enable
The function reset enable bit is set to 1 by the MCU to enable the USB reset to reset all internal logic
including the MCU. However, the shadow the ROM (SDW) and the USB function connect (CONT)
bits will not be reset. When this bit is set, the reset output (RSTO) signal from the TAS1020 device
will also be active when a USB reset occurs. This bit is not affected by USB reset.
3
—
Reserved
Reserved for future use.
2
—
Reserved
Reserved for future use.
1
—
Reserved
Reserved for future use.
0
SDW_OK
SDW bit confirm
This bit is used as a confirmation bit to prevent a user to spuriously clear the SDW bit in the
MEMCFG register. This bit must be set to 1 before clearing the SDW bit to switch from normal
mode to boot mode. This bit is not affected by USB reset.
A–19
A.5.1.5 USB Frame Number Register (Low-byte) (USBFNL – Address FFFBh)
The USB frame number register (low byte) contains the least significant byte of the 11-bit frame number value
received from the host PC in the start-of-frame packet.
Bit
7
6
5
4
3
2
1
0
FN7
FN6
FN5
FN4
FN3
FN2
FN1
FN0
Type
R
R
R
R
R
R
R
R
Default
0
0
0
0
0
0
0
0
Mnemonic
BIT
7:0
MNEMONIC
NAME
FN(7:0)
DESCRIPTION
Frame number
The frame number bit values are updated by hardware each USB frame with the frame number
field value received in the USB start-of-frame packet. The frame number can be used as a time
stamp by the USB function. If the TAS1020 frame timer is not locked to the host PC frame timer,
then the frame number is incremented from the previous value when a pseudo start-of-frame
occurs.
A.5.1.6 USB Frame Number Register (High-byte) (USBFNH – Address FFFAh)
The USB frame number register (high byte) contains the most significant 3 bits of the 11-bit frame number value
received from the host PC in the start-of-frame packet.
Bit
7
6
5
4
3
2
1
0
Mnemonic
—
—
—
—
—
FN10
FN9
FN8
Type
R
R
R
R
R
R
R
R
Default
0
0
0
0
0
0
0
0
BIT
MNEMONIC
NAME
DESCRIPTION
7:3
—
Reserved
Reserved for future use.
2:0
FN(10:8)
Frame number
The frame number bit values are updated by hardware each USB frame with the frame number
field value received in the USB start-of-frame packet. The frame number can be used as a time
stamp by the USB function. If the TAS1020 frame timer is not locked to the host PC frame timer,
then the frame number is incremented from the previous value when a pseudo start-of-frame
occurs.
A.5.2
DMA Registers
This section describes the memory-mapped registers used for the two DMA channels. Each DMA channel has a set
of three registers.
A.5.2.1 DMA Time Slot Assignment Register (Low-byte) (DMATSL1 – Address FFF0h)
(DMATSL0 – Address FFEAh)
Bit
7
6
5
4
3
2
1
0
Mnemonic
TSL7
TSL6
TSL5
TSL4
TSL3
TSL2
TSL1
TSL0
Type
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
0
0
0
0
0
0
0
0
Default
BIT
7:0
A–20
MNEMONIC
TSL(7:0)
NAME
Time slot assignment
DESCRIPTION
The DMA time slot assignment bits are set to 1 by the MCU to define the codec port
interface time slots supported by this DMA channel.
A.5.2.2 DMA Time Slot Assignment Register (High-byte) (DMATSH1 – Address FFEFh)
(DMATSH0 – Address 0xFFE9)
Bit
Mnemonic
7
6
5
4
3
2
1
0
BPTS1
BPTS0
TSL13
TSL12
TSL11
TSL10
TSL9
TSL8
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
0
0
0
0
0
0
0
0
Type
Default
BIT
MNEMONIC
NAME
DESCRIPTION
7:6
BPTS(1:0)
Bytes per time slot
The bytes per time slot bits are used to define the number of bytes to be transferred for each
time slot supported by this DMA channel.
00b = 1 byte,
01b = 2 bytes,
10b = 3 bytes,
11b = 4 bytes
5:0
TSL(13:8)
Time slot assignment
The DMA time slot assignment bits are set to 1 by the MCU to define the codec port
interface time slots supported by this DMA channel.
A.5.2.3 DMA Control Register (DMACTL1 – Address FFEEh) (DMACTL0 – Address FFE8h)
Bit
Mnemonic
7
6
5
4
3
2
1
0
DMAEN
HSKEN
—
—
EPDIR
EPNUM2
EPNUM1
EPNUM0
R/W
R/W
R
R
R/W
R/W
R/W
R/W
0
0
0
0
0
0
0
0
Type
Default
BIT
MNEMONIC
NAME
DESCRIPTION
7
DMAEN
DMA enable
The DMA enable bit is set to a 1 by the MCU to enable this DMA channel. Before enabling
the DMA channel, all other DMA channel configuration bits must be set to the desired value.
6
HSKEN
Handshake enable
This bit is relevant for BULK data transfer in the OUT direction through DMA. MCU must set
this bit to a 1 to enable the handshake mode for the data transfer. If MCU sets this bit, MCU
has to enable DMA for each received BULK OUT packet. DMA, once enabled, transfers the
BULK OUT packet to the C-port, disables itself and generates an interrupt to the MCU. If
MCU clears this bit, DMA handles the BULK OUT data transfer to the C-port without MCU
intervention. For more details, refer to section 2.2.7.3.3.
5
—
Reserved
Reserved for future use
4
—
Reserved
Reserved for future use
3
EPDIR
USB end-point direction
The USB end-point direction bit controls the direction of data transfer by this DMA channel.
The MCU should set this bit to a 1 to configure this DMA channel to be used for a USB in
end-point. The MCU must clear this bit to a 0 to configure this DMA channel to be used for a
USB out end-point.
EPNUM(2:0)
USB end-point number
The USB end-point number bits are set by the MCU to define the USB end-point number
supported by this DMA channel. Keep in mind that end-point 0 is always used for the control
end-point, which is serviced by the MCU and not a DMA channel.
001b = End-Point 1, 010b = End-Point 2, …, 111b = End-Point 7
2:0
A.5.2.4 DMA Current Buffer Content Register (Low-Byte) (DMABCNT1L – Address FFE3h)
(DMABCNT0L– Address FFEBh)
Bit
Mnemonic
7
6
5
4
3
2
1
0
Size 7
Size 6
Size 5
Size 4
Size 3
Size 2
Size 1
Size 0
Type
R
R
R
R
R
R
R
R
Default
0
0
0
0
0
0
0
0
BIT
7:0
MNEMONIC
Size(7:0)
NAME
Buffer content
DESCRIPTION
This register shows the buffer content (bytes) for an ISO OUT end-point. This register is updated
every SOF and is stable for the following USB frame which MCU can read it to implement USB
audio synchronization.
A–21
A.5.2.5 DMA Current Buffer Content Register (High-Byte) (DMABCNT1H – Address FFE4h)
(DMABCNT0H – Address FFECh)
Bit
7
6
5
4
3
2
1
0
Size 15
Size 14
Size 13
Size 12
Size 11
Size 10
Size 9
Size 8
Type
R
R
R
R
R
R
R
R
Default
0
0
0
0
0
0
0
0
Mnemonic
BIT
7:0
MNEMONIC
NAME
Size(15:8)
DESCRIPTION
Buffer content
This register shows the buffer content (bytes) for an ISO OUT end-point. This register is updated
every SOF and is stable for the following USB frame which MCU can read it to implement USB
audio synchronization.
A.5.2.6 DMA Bulk Packet Count Register (Low-byte) (DMABPCT0 – Address FFF2h)
Bit
Mnemonic
7
6
5
4
3
2
1
0
PCNT7
PCNT6
PCNT5
PCNT4
PCNT3
PCNT2
PCNT1
PCNT0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
0
0
0
0
0
0
0
0
Type
Default
BIT
7:0
MNEMONIC
PCNT (7:0)
NAME
DESCRIPTION
Bulk packet count
This register shows the number of BULK OUT packets DMA has to handle in handshake mode.
MCU writes to this register before enabling the DMA to program the DMA to handle up to 64K
BULK packets without MCU intervention. MCU can read this register anytime.
A.5.2.7 DMA Bulk Packet Count Register (High-byte) (DMABPCT1 – Address FFF1h)
Bit
Mnemonic
7
6
5
4
3
2
1
0
PCNT15
PCNT14
PCNT13
PCNT12
PCNT11
PCNT10
PCNT9
PCNT8
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
0
0
0
0
0
0
0
0
Type
Default
BIT
7:0
MNEMONIC
PCNT (15:8)
NAME
DESCRIPTION
Bulk packet count
This register shows the number of BULK OUT packets DMA has to handle in handshake mode.
MCU writes to this register before enabling the DMA to program the DMA to handle up to 64K
BULK packets without MCU intervention. MCU can read this register anytime.
A.5.2.8 UBM Write Pointer (Low Byte) (Ch0WrPtrL – Address FFBCh) (Ch1WrPtrL – Address FFB8h)
Bit
Mnemonic
7
6
5
4
3
2
1
0
WRPTR7
WRPTR6
WRPTR5
WRPTR4
WRPTR3
WRPTR2
WRPTR1
WRPTR0
Type
R
R
R
R
R
R
R
R
Default
0
0
0
0
0
0
0
0
BIT
7:0
A–22
MNEMONIC
WRPTR(7:0)
NAME
DESCRIPTION
UBM Write Pointer
This register contains 8 LSB bits of 11-bit UBM Write Pointer of the isochronous OUT endpoint
buffer. MCU can read this register anytime. This 11-bit UBM Write Pointer WRPTR can be used
in conjunction with the corresponding 11-bit Chn DMA RDPTR to estimate the isochronous OUT
endpoint buffer size.
A.5.2.9 UBM Write Pointer (High Byte) (Ch0WrPtrH – Address FFBBh)
(Ch1WrPtrH – Address FFB7h)
Bit
7
6
5
4
3
2
1
0
Mnemonic
—
—
—
—
—
WRPTR10
WRPTR9
WRPTR8
Type
—
—
—
—
—
R
R
R
Default
—
—
—
—
—
0
0
0
BIT
MNEMONIC
NAME
DESCRIPTION
2:0
WRPTR(10:8)
UBM Write Pointer
This register contains 3 MSB bits of 11-bit UBM Write Pointer of the isochronous OUT endpoint
buffer. MCU can read this register anytime. This 11-bit UBM Write Pointer WRPTR can be used
in conjunction with the corresponding 11-bit Chn DMA RDPTR to estimate the isochronous OUT
endpoint buffer size.
A.5.2.10DMA Read Pointer (Low Byte) (Ch0RdPtrH – Address FFBAh) (Ch1RrPtrH – Address FFB6h)
Bit
7
6
5
4
3
2
1
0
RDPTR7
RDPTR6
RDPTR5
RDPTR4
RDPTR3
RDPTR2
RDPTR1
RDPTR0
Type
R
R
R
R
R
R
R
R
Default
0
0
0
0
0
0
0
0
Mnemonic
BIT
7:0
MNEMONIC
RDPTR(7:0)
NAME
DESCRIPTION
DMA Read Pointer
This register contains 8 LSB bits of 11-bit DMA channel n (n can be 0 or 1) Read Pointer of the
Isochronous OUT endoint buffer. MCU can read this register anytime. This 11-bit CHn DMA
Read pointer RDPTR can be used in conjunction with the corresponding 11-bit UBM Write
Pointer WRPTR to estimate the isochronous OUT endpoint buffer size.
A.5.2.11DMA Read Pointer (High Byte) (Ch0RdPtrH – Address FFB9h) (Ch1RrPtrH – Address FFB5h)
Bit
7
6
5
4
3
2
1
0
Mnemonic
—
—
—
—
—
WRPTR10
WRPTR9
WRPTR8
Type
—
—
—
—
—
R
R
R
Default
—
—
—
—
—
0
0
0
BIT
MNEMONIC
NAME
DESCRIPTION
2:0
RDPTR(10:8)
DMA Read Pointer
This register contains 3 MSB bits of 11-bit channel n (n can be 0 or 1) Read Pointer of the
Isochronous OUT endoint buffer. MCU can read this register anytime. This 11-bit CHn DMA
RDPTR can be used in conjunction with the corresponding 11-bit UBM Write Pointer WRPTR to
estimate the isochronous OUT endpoint buffer size.
A–23
A.5.3
Adaptive Clock Generator Registers
This section describes the memory-mapped registers used for two adaptive clock generators for their controls and
operations.
A.5.3.1 Adaptive Clock Generator1 Frequency Register (Byte 0) (ACG1FRQ0 – Address FFE7h)
The adaptive clock generator frequency register (byte 0) contains the least significant byte of the 24-bit ACG
frequency value. The adaptive clock generator frequency registers, ACG1FRQ0, ACG1FRQ1, and ACG1FRQ2,
contain the 24-bit value used to program the ACG1 frequency synthesizer. The 24-bit value of these three registers
is used to determine the codec master clock output (MCLKO) signal frequency. See section 2.2.8 for the operation
details of the adaptive clock generator including instructions for programming the 24-bit ACG frequency value.
Bit
Mnemonic
Type
7
6
5
4
3
2
1
0
FRQ7
FRQ6
FRQ5
FRQ4
FRQ3
FRQ2
FRQ1
FRQ0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
0
0
0
0
0
0
0
0
Default
BIT
7:0
MNEMONIC
NAME
FRQ(7:0)
DESCRIPTION
ACG frequency
The ACG frequency bit values are set by the MCU to program the ACG frequency synthesizer to
obtain the desired codec master clock output (MCLKO) signal frequency.
A.5.3.2 Adaptive Clock Generator1 Frequency Register (Byte 1) (ACGFRQ1 – Address FFE6h)
The adaptive clock generator frequency register (byte 1) contains the middle byte of the 24-bit ACG 1 frequency
value.
Bit
Mnemonic
7
6
5
4
3
2
1
0
FRQ15
FRQ14
FRQ13
FRQ12
FRQ11
FRQ10
FRQ9
FRQ8
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
0
0
0
0
0
0
0
0
Type
Default
BIT
7:0
MNEMONIC
NAME
FRQ(15:8)
DESCRIPTION
ACG frequency
The ACG frequency bit values are set by the MCU to program the ACG frequency synthesizer to
obtain the desired codec master clock output (MCLKO) signal frequency.
A.5.3.3 Adaptive Clock Generator1 Frequency Register (Byte 2) (ACG1FRQ2 – Address FFE5h)
The adaptive clock generator frequency register (byte 2) contains the most significant byte of the 24-bit ACG
frequency value.
Bit
Mnemonic
7
6
5
4
3
2
1
0
FRQ23
FRQ22
FRQ21
FRQ20
FRQ19
FRQ18
FRQ17
FRQ16
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
0
0
0
0
0
0
0
0
Type
Default
BIT
7:0
A–24
MNEMONIC
FRQ(23:16)
NAME
ACG frequency
DESCRIPTION
The ACG frequency bit values are set by the MCU to program the ACG frequency synthesizer to
obtain the desired codec master clock output (MCLKO) signal frequency.
A.5.3.4 Adaptive Clock Generator1 MCLK Capture Register (Low byte)
(ACG1CAPL – Address FFE4h)
The adaptive clock generator MCLK capture register (low byte) contains the least significant byte of the 16-bit codec
master clock (MCLK) signal cycle count that is captured each time a USB start of frame (SOF) occurs. The value of
a16-bit free running counter, which is clocked with the MCLK signal, is captured at the beginning of each USB frame.
The source of the MCLK signal used to clock the 16-bit timer can be selected to be either the MCLKO signal or the
MCLKO2 signal. See section 2.2.10 for the operation details of the adaptive clock generator.
Bit
7
6
5
4
3
2
1
0
CAP7
CAP6
CAP5
CAP4
CAP3
CAP2
CAP1
CAP0
Type
R
R
R
R
R
R
R
R
Default
0
0
0
0
0
0
0
0
Mnemonic
BIT
7:0
MNEMONIC
NAME
CAP(7:0)
ACG MCLK capture
DESCRIPTION
The ACG MCLK capture bit values are updated by hardware each time a USB start of frame
occurs. This register contains the least signification byte of the 16-bit value.
A.5.3.5 Adaptive Clock Generator1 MCLK Capture Register (High-byte)
(ACGCAPH – Address FFE3h)
The adaptive clock generator MCLK capture register (high byte) contains the most significant byte of the 16-bit codec
master clock (MCLK) signal cycle count that is captured each time a USB start of frame (SOF) occurs.
Bit
7
6
5
4
3
2
1
0
CAP15
CAP14
CAP13
CAP12
CAP11
CAP10
CAP9
CAP8
Type
R
R
R
R
R
R
R
R
Default
0
0
0
0
0
0
0
0
Mnemonic
BIT
7:0
MNEMONIC
NAME
CAP(15:8)
ACG MCLK capture
DESCRIPTION
The ACG MCLK capture bit values are updated by hardware each time a USB start of frame
occurs. This register contains the most signification byte of the 16-bit value.
A.5.3.6 Adaptive Clock Generator2 Frequency Register (Byte 0) (ACG2FRQ0 – Address FFF9h)
The adaptive clock generator control registers ACG2FRQ0, ACG2FRQ1, and ACG2FRQ2, contain the 24-bit value
used to program the ACG2 frequency synthesizer.
Bit
Mnemonic
Type
7
6
5
4
3
2
1
0
FRQ7
FRQ6
FRQ5
FRQ4
FRQ3
FRQ2
FRQ1
FRQ0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
0
0
0
0
0
0
0
0
Default
BIT
7:0
MNEMONIC
NAME
FRQ(7:0)
ACQ2 frequency
DESCRIPTION
The ACG2 frequency bit values are set by the MCU to program the ACG2 frequency
synthesizer.
A.5.3.7 Adaptive Clock Generator Frequency Register (Byte 1) (ACG2FRQ1 – Address FFF8h)
Bit
Mnemonic
Type
7
6
5
4
3
2
1
0
FRQ15
FRQ14
FRQ13
FRQ12
FRQ11
FRQ10
FRQ9
FRQ8
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
0
0
0
0
0
0
0
0
Default
BIT
7:0
MNEMONIC
FRQ(15:8)
NAME
ACQ2 frequency
DESCRIPTION
The ACG2 frequency bit values are set by the MCU to program the ACG2 frequency
synthesizer.
A–25
A.5.3.8 Adaptive Clock Generator Frequency Register (Byte 2) (ACG2FRQ2 – Address FFF7h)
Bit
Mnemonic
7
6
5
4
3
2
1
0
FRQ23
FRQ22
FRQ21
FRQ20
FRQ19
FRQ18
FRQ17
FRQ16
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
0
0
0
0
0
0
0
0
Type
Default
BIT
7:0
MNEMONIC
FRQ(23:16)
NAME
DESCRIPTION
ACQ2 frequency
The ACG2 frequency bit values are set by the MCU to program the ACG2 frequency synthesizer.
A.5.3.9 Adaptive Clock Generator2 Divider Control Register (ACG2DCTL – Address FFF6h)
Bit
Mnemonic
Type
7
6
5
4
3
2
1
DIVM3
DIVM2
DIVM1
DIVM0
–
–
–
–
R/W
R/W
R/W
R/W
R
R
R
R
0
0
0
0
0
0
0
0
Default
BIT
MNEMONIC
NAME
0
DESCRIPTION
7:0
DIVM(3:0)
Divide by M value
The divide by M control bits are set by the MCU to program the ACG2 frequency divider.
0000b = divide by 1, 0001b = divide by 2, ... 1111b = divide by 16
3:0
–
Reserved
Reserved for future use.
A.5.3.10 Adaptive Clock Generator1 Divider Control Register (ACG1DCTL – Address FFE2h)
Bit
Mnemonic
Type
7
6
5
4
DIVM3
DIVM2
DIVM1
R/W
R/W
R/W
0
0
0
Default
BIT
MNEMONIC
NAME
3
2
1
0
DIVM0
–
DIV12
DIV11
DIV10
R/W
R
R/W
R/W
R/W
0
0
0
0
0
DESCRIPTION
7:0
DIVM(3:0)
Divide by M value
The divide by M control bits are set by the MCU to program the ACG1 frequency divider.
0000b = divide by 1, 0001b = divide by 2, ... 1111b = divide by 16
2:0
DIVI(2:0)
Divide by I value
The divide by I control bits are set by the MCU to program the MCKLKI divider.
000b = divide by 1, 001b = divide by 2, ..., 111b = divide by 8
A–26
A.5.3.11 Adaptive Clock Generator Control Register (ACGCTL – Address FFE1h)
Bit
Mnemonic
7
6
5
4
3
2
1
0
MCLKO2EN
MCLKO2EN
–
MCLKO1S1
MCLKO1S0
DIVEN
MCLKO2S1
MCLKO2S0
R/W
R/W
R
R/W
R/W
R/W
R/W
R/W
0
0
0
0
0
0
0
0
Type
Default
BIT
NAME
DESCRIPTION
7
MCLKO2EN
MCLKO2 Output enable
This bit is set to 1 by the MCU to enable the MCLKO2 signal to be an output from the
TAS1020 device. If the MCLKO2 signal is not being used, then the MCU can clear this bit to
0 to disable the output.
6
MCLKO1EN
MCLKO1 Output enable
This bit is set to 1 by the MCU to enable the MCLKO1 signal to be an output from the
TAS1020 device. If the MCLKO1 signal is not being used, then the MCU can clear this bit to
0 to disable the output.
4
MCLKO1S1
MCLKO1 Clock select
This bit in conjunction with MCLKO1S0, selects the MCLKO1. Refer to ACG block diagram.
MCLKO1S1
MCLKO1S0
MCLKO1
0
0
acg_clk (after %M)
x
1
mclki (after %I)
1
0
acg2_clk(after %M)
3
MCLKO1S0
MCLKO1 Clock select
Refer to the description above.
2
DIVEN
Divider Enable
The Divider Enable bit is set to 1 by the MCU to enable the Divide-by-I and Divide-by-M
circuits.
1
MCLKO2
MCLKO1 Clock select
This bit in conjunction with MCLKO2S0, selects the MCLKO2. Refer to ACG block diagram.
MCLKO2S1
MCLKO2S0
MCLKO2
0
0
acg_clk (after %M)
x
1
mclki (after %I)
1
0
acg2_clk(after %M)
0
MCLKO2S0
MCLKO2 Clock select
Refer to the description above.
A.5.4
MNEMONIC
Codec Port Interface Registers
This section describes the memory-mapped registers used for the codec port interface control and operation. The
codec port interface has a set of ten registers. Note that the four codec port interface configuration registers can only
be written to by the MCU if the codec port enable bit (CPTEN) in the global control register is a 0.
A.5.4.1 Codec Port Interface Configuration Register 1 (CPTCNF1 – Address FFE0h)
The codoec port interface configuration register 1 is used to store various control bits for the codec port interface
operation.
Bit
Mnemonic
Type
7
6
5
4
3
2
1
0
NTSL4
NTSL3
NTSL2
NTSL1
NTSL0
MODE2
MODE1
MODE0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
0
0
0
0
0
0
0
0
Default
BIT
NAME
DESCRIPTION
7:3
NTSL(4:0)
MNEMONIC
Number of time slots
The number of time slots bits are set by the MCU to program the number of time slots per audio
frame.
00000b = 1 time slot per frame, 00001b = 2 time slots per frame, …, 01101 = 14 time slots per
frame
2:0
MODE(2:0)
Mode select
The mode select bits are set by the MCU to program the codec port interface mode of
operation. In addition to selecting the desired mode of operation, the MCU must also program
the other configuration registers to obtain the correct serial interface format.
000b = mode 0 - General-purpose mode
001b = mode 1 - AIC mode
010b = mode 2 - AC ’97 1.X mode
011b = mode 3 - AC ’97 2.X mode
100b = mode 4 - I2S mode – 1 OUT and 2 IN at same frequency
101b = mode 5 - I2S mode – 1 OUT and 1 IN at different frequencies
A–27
A.5.4.2 Codec Port Interface Configuration Register 2 (CPTCNF2 – Address FFDFh)
The codec port interface configuration register 2 is used to store various control bits for the codec port interface
operation.
Bit
Mnemonic
7
6
5
4
3
2
1
0
TSL0L1
TSL0L0
BPTSL2
BPTSL1
BPTSL0
TSLL2
TSLL1
TSLL0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
0
0
0
0
0
0
0
0
Type
Default
BIT
MNEMONIC
NAME
DESCRIPTION
7:6
TSL0L(1:0)
Time slot 0 length
The time slot 0 Length bits are set by the MCU to program the number of serial clock
(CSCLK) cycles for time slot 0.
00b = CSCLK cycles for time slot 0 same as other time slots
01b = 8 CSCLK cycles for time slot 0
10b = 16 CSCLK cycles for time slot 0
11b = 32 CSCLK cycles for time slot 0
5:3
BPTSL(2:0)
Data bits per time slot
The data bits per time slot bits are set by the MCU to program the number of data bits per
audio time slot. Note that this value in not used for the secondary communication address
and data time slots.
000b = 8 data bits per time slot
001b = 16 data bits per time slot
010b = 18 data bits per time slot
011b = 20 data bits per time slot
100b = 24 data bits per time slot
101b = 32 data bits per time slot
110b = reserved
111b = reserved
2:0
TSLL(2:0)
Time slot length
The time slot length bits are set by the MCU to program the number of serial clock (CSCLK)
cycles for all time slots except time slot 0.
000b = 8 CSCLK cycles per time slot
001b = 16 CSCLK cycles per time slot
010b = 18 CSCLK cycles per time slot
011b = 20 CSCLK cycles per time slot
100b = 24 CSCLK cycles per time slot
101b = 32 CSCLK cycles per time slot
110b = reserved
111b = reserved
A–28
A.5.4.3 Codec port interface configuration register 3 (CPTCNF3 – Address FFDEh)
The codec port interface configuration register 3 is used to store various control bits for the codec port interface
operation.
Bit
Mnemonic
Type
7
6
5
4
3
2
1
0
DDLY
TRSEN
CSCLKP
CSYNCP
CSYNCL
BYOR
CSCLKD
CSYNCD
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
0
0
1
1
0
0
0
0
Default
BIT
MNEMONIC
NAME
DESCRIPTION
7
DDLY
Data delay
The data delay bit is set to a 1 by the MCU to program a one CSCLK cycle delay of the serial
data output and input signals in reference to the leading edge of the CSYNC signal. The
MCU must clear this bit to a 0 for no delay between these signals.
6
TRSEN
3-State enable
The 3-state enable bit is set to a 1 by the MCU to program the hardware to 3-state the serial
data output signal for the time slots during the audio frame that are not valid. The MCU must
clear this bit to a 0 to program the hardware to use zero-padding for the serial data output
signal for time slots during the audio frame that are not valid.
5
CSCLKP
CSCLK polarity
The CSCLK polarity bit is used by the MCU to program the clock edge used for the codec
port interface frame sync (CSYNC) output signal, codec port interface serial data output
(CDATO) signal and codec port interface serial data Input (CDATI) signal. When this bit is
set to a 1, the CSYNC signal will be generated with the negative edge of the codec port
interface serial clock (CSCLK) signal. Also, when this bit is set to a 1, the CDATO signal is
generated with the negative edge of the CSCLK signal and the CDATI signal is sampled
with the positive edge of the CSCLK signal. When this bit is cleared to a 0, the CSYNC
signal is generated with the positive edge of the CSCLK signal. Also, when this bit is
cleared to a 0, the CDATO signal is generated with the positive edge of the CSCLK signal
and the CDATI signal is sampled with the negative edge of the CSCLK signal.
4
CSYNCP
CSYNC polarity
The CSYNC polarity bit is set to a 1 by the MCU to program the polarity of the codec port
interface frame sync (CSYNC) output signal to be active high. The MCU must clear this bit
to a 0 to program the polarity of the CSYNC output signal to be active low.
3
CSYNCL
CSYNC length
The CSYNC length bit is set to a 1 by the MCU to program the length of the codec port
interface frame sync (CSYNC) output signal to be the same number of CSCLK cycles as
time slot 0. The MCU must clear this bit to a 0 to program the length of the CSYNC output
signal to be one CSCLK cycle.
2
BYOR
Byte order
The byte order bit is used by the MCU to program the byte order for the data moved by the
DMA between the USB end-point buffer and the codec port interface. When this bit is set to
a 1, the byte order of each audio sample is reversed when the data is moved to/from the
USB end-point buffer. When this bit is cleared to a 0, the byte order of the each audio
sample is unchanged.
1
CSCLKD
CSCLK direction
The CSCLK direction bit is set to a 1 by the MCU to program the direction of the codec port
interface serial clock (CSCLK) signal as an input to the TAS1020 device. The MCU must
clear this bit to a 0 to program the direction of the CSCLK signal as an output from the
TAS1020 device.
0
CSYNCD
CSYNC direction
The CSYNC direction bit is set to a 1 by the MCU to program the direction of the codec port
interface frame sync (CSYNC) signal as an input to the TAS1020 device. The MCU must
clear this bit to a 0 to program the direction of the CSYNC signal as an output from the
TAS1020 device.
A–29
A.5.4.4 Codec Port Interface Configuration Register 4 (CPTCNF4 – Address FFDDh)
The codec port interface configuration register 4 is used to store various control bits for the codec port interface
operation.
Bit
Mnemonic
Type
7
6
5
4
3
2
1
0
ATSL3
ATSL2
ATSL1
ATSL0
CLKS
DIVB2
DIVB1
DIVB0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
0
0
0
0
0
0
0
0
Default
BIT
7:4
3
2:0
A–30
NAME
DESCRIPTION
ATSL(3:0)
MNEMONIC
Command/status address/data
time slot
The command/status address/data time slot bits are set by the MCU to program the
time slots to be used for the secondary communication address and data values. For
the AC ’97 modes of operation, this value must be set to 0001b which results in time
slot 1 being used for the address and time slot 2 being used for the data. For the AIC
and general-purpose modes of operation, the same time slot is used for both
address and data. For the AIC mode of operation, for example, this value must be
set to 0111b which results in time slot 7 being used for both the address and data.
0000b = time slot 0, 0001b = time slot 1, …, 1111b = time slot 15
CptBlk
C-port bulk mode
This bit is used when C-port is in Mode 0. In this mode, MCU or DMA can send ISO or
BULK data to the C-port. If this bit is cleared to 0, the C-port sync/clocks are free
running once C-port is enabled. If this bit is set to 1, DMA controls the C-port
sync/clocks. The sync/clocks are active only when valid data is present in a codec
frame.
DIVB(2:0)
Divide by B value
The divide by B control bits are set by the MCU to program the CSCLK signal divider.
000b = disabled
001b = divide by 2
010b = divide by 3
011b = divide by 4
100b = divide by 5
101b = divide by 6
110b = divide by 7
111b = divide by 8
A.5.4.5 Codec Port Interface Control and Status Register (CPTCTL – Address FFDCh)
The codec port interface control and status register contains various control and status bits used for the codec port
interface operation.
Bit
7
6
5
4
3
2
1
0
RXF
RXIE
TXE
TXIE
—
CID1
CID0
CRST
Type
R
R/W
R
R/W
R
R/W
R/W
R/W
Default
0
0
0
0
0
0
0
0
Mnemonic
BIT
MNEMONIC
NAME
DESCRIPTION
7
RXF
Receive data register full
The receive data register full bit is set to a 1 by hardware when a new data value has
been received into the receive data register from the codec device. This bit is read
only and is cleared to a 0 by hardware when the MCU reads the new value from the
receive data register. Note that when the MCU writes to the interrupt vector register,
the codec port interface receive data register full interrupt is cleared but this status
bit is not cleared at that time.
6
RXIE
Receive interrupt enable
The receive interrupt enable bit is set to a 1 by the MCU to enable the C-port receive
data register full interrupt.
5
TXE
Transmit data register empty
The transmit data register empty bit is set to a 1 by hardware when the data value in
the transmit data register has been sent to the codec device. This bit is read only and
is cleared to a 0 by hardware when a new data byte is written to the transmit data
register by the MCU. Note that when the MCU writes to the interrupt vector register,
the codec port interface transmit data register empty interrupt is cleared but this
status bit is not cleared at that time.
4
TXIE
Transmit interrupt enable
The transmit interrupt enable bit is set to a 1 by the MCU to enable the codec port
interface transmit data register empty interrupt.
3
—
Reserved
Reserved for future use
CID(1:0)
Codec ID
The codec ID bits are used by the MCU to select between the primary codec device
and the secondary codec device for secondary communication in the AC ’97 modes
of operation. When the bits are cleared to ’00’, the primary codec device is selected.
When the bits are set to ’01’, ’10’ or ’11’, the secondary codec device is selected.
Note that when only a primary codec device is connected to the TAS1020, the bits
remain cleared to ’00’.
CRST
Codec reset
The codec reset bit is used by the MCU to control the codec port interface reset
(CRESET) output signal from the TAS1020 device. When this bit is set to a 1, the
CRESET signal is a high. When this bit is cleared to a 0, the CRESET signal is active
low. At power up this bit is cleared to a 0, which means the CRESET output signal is
active low and remains active low until the MCU sets this bit to a 1. Note that this
output signal is not used in the I2S modes of operation.
2:1
0
A–31
A.5.4.6 Codec Port Interface Address Register (CPTADR –@ Address FFDBh)
The codec port interface address register contains the read/write control bit and address bits used for secondary
communication between the TAS1020 MCU and the codec device. For write transactions to the codec, the 8-bit value
in this register is sent to the codec in the designated time slot and appropriate bit locations. Note that for the different
modes of operation, the number of address bits and the bit location of the read/write bit is different. For example, the
AC ’97 modes require 7 address bits and the bit location of the read/write bit to be the most significant bit. The AIC
mode only requires 4 address bits and the bit location of the read/write bit to be bit 13 of the 16-bits in the time slot.
The MCU must load the read/write and address bits to the correct bit locations within this register for the different
modes of operation. Shown below are the read/write control bit and address bits for the AC ’97 mode of operation.
Bit
7
6
5
4
3
2
1
0
Mnemonic
R/W
A6
A5
A4
A3
A2
A1
A0
Type
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
0
0
0
0
0
0
0
0
Default
BIT
7
6:0
MNEMONIC
NAME
DESCRIPTION
R/W
Command/status read/write
control
The command/status read/write control bit value is set by the MCU to program the
type of secondary communication transaction to be done. This bit must be set to a 1
by the MCU for a read transaction and cleared to a 0 by the MCU for a write
transaction.
A(6:0)
Command/status address
The command/status address value is set by the MCU to program the codec device
control/status register address to be accessed during the read or write transaction.
The command/status address value is updated by hardware with the control/status
register address value received from the codec device for read transactions.
A.5.4.7 Codec Port Interface Data Register (Low Byte) (CPTDATL – Address FFDAh)
The codec port interface data register (low byte) contains the least significant byte of the 16-bit command or status
data value used for secondary communication between the TAS1020 MCU and the codec device. Note that for
general-purpose mode or AIC mode only an 8-bit data value is used for secondary communication.
Bit
7
Mnemonic
Type
7:0
A–32
4
3
2
1
0
D7
D6
D5
D4
D3
D2
D1
D0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
0
0
0
0
0
0
0
0
MNEMONIC
D(7:0)
5
R/W
Default
BIT
6
NAME
Command/status data
DESCRIPTION
The command/status data value is set by the MCU with the command data to be
transmitted to the codec device for write transactions. The command/status data
value is updated by hardware with the status data received from the codec device for
read transactions.
A.5.4.8 Codec Port Interface Data Register (High Byte) (CPTDATH – Address FFD9h)
The codec port interface data register (high byte) contains the most significant byte of the 16-bit command or status
data value used for secondary communication between the TAS1020 MCU and the codec device. This register is not
used for general-purpose mode or AIC mode since these modes only support an 8-bit data value for secondary
communication.
Bit
7
6
5
4
3
2
1
0
Mnemonic
D15
D14
D13
D12
D11
D10
D9
D8
Type
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
0
0
0
0
0
0
0
0
Default
BIT
7:0
MNEMONIC
NAME
D(15:8)
DESCRIPTION
Command/status data
The command/status data value is set by the MCU with the command data to be
transmitted to the codec device for write transactions. The command/status data
value is updated by hardware with the status data received from the codec device for
read transactions.
A.5.4.9 Codec Port Interface Valid Time Slots Register (Low Byte) (CPTVSLL – Address FFD8h)
The codec port interface valid time slots register (low byte) contains the control bits used to specify which time slots
in the audio frame contain valid data. This register is only used in the AC ’97 modes of operation.
Bit
Mnemonic
7
6
5
4
3
2
1
0
VTSL8
VTSL9
VTSL10
VTSL11
VTSL12
—
—
—
R/W
R/W
R/W
R/W
R/W
R
R
R
0
0
0
0
0
0
0
0
Type
Default
BIT
MNEMONIC
NAME
DESCRIPTION
7:3
VTSL(8:12)
Valid time slot
The valid time slot bits are set to a 1 by the MCU to define which time slots in the
audio frame contain valid data. The MCU must clear to a 0 the bits corresponding to
time slots that do not contain valid data. Note that bits 7 to 3 of this register
correspond to time slots 8 to 12.
2:0
—
Reserved
Reserved for future use
A–33
A.5.4.10 Codec Port Interface Valid Time Slots Register (High Byte) (CPTVSLH – Address FFD7h)
The codec port interface valid time slots register (high byte) contains the control bits used to specify which time slots
in the audio frame contain valid data. In addition the valid frame, primary codec ready and secondary codec ready
bits are contained in this register. This register is only used in the AC ’97 modes of operation.
Bit
Mnemonic
Type
6
5
4
3
2
1
0
VF
PCRDY
SCRDY
VTSL3
VTSL4
VTSL5
VTSL6
VTSL7
R/W
R
R
R/W
R/W
R/W
R/W
R/W
0
0
0
0
0
0
0
0
Default
BIT
7
MNEMONIC
NAME
DESCRIPTION
7
VF
Valid frame
The valid frame bit is set to a 1 by the MCU to indicate that the current audio frame
contains at least one time slot with valid data. The MCU must clear this bit to a 0 to
indicate that the current audio frame does not contain any time slots with valid data.
6
PCRDY
Primary codec ready
The primary codec ready bit is updated by hardware each audio frame based on the
value of bit 15 in time slot 0 of the incoming serial data from the primary codec. This
bit is set to a 1 to indicate the primary codec is ready for operation.
5
SCRDY
Secondary codec ready
The secondary codec ready bit is updated by hardware each audio frame based on
the value of bit 15 in time slot 0 of the incoming serial data from the secondary codec.
This bit is set to a 1 to indicate the secondary codec is ready for operation. Note that
this bit is only used if a secondary codec is connected to the TAS1020 device.
VTSL(3:7)
Valid time slot
The valid time slot bits are set to a 1 by the MCU to define which time slots in the
audio frame contain valid data. The MCU must clear to a 0 the bits corresponding to
time slots that do not contain valid data. Note that bits 4 to 0 of this register
correspond to time slots 3 to 7.
4:0
A.5.4.11 Codec Port Receive Interface Configuration Register 2 (CPTRXCNF2 – Address FFD6h)
The codec port receive interface configuration register2 is only used in I2S Mode 5.
Bit
7
6
5
4
3
2
1
0
Mnemonic
–
–
BPTSL2
BPTSL1
BPTSL0
TSLL2
TSLL1
TSSL0
Type
R
R
R/W
R/W
R/W
R/W
R/W
R/W
Default
0
0
0
0
0
0
0
0
BIT
MNEMONIC
NAME
DESCRIPTION
5:3
BPTSL(2:0)
Data bits per time slot.
The data bits per time slot bits are set by the MCU to program the number of data bits
per audio time slot. Note that this value in not used for the secondary communication
address and data time slots.
000b = 8 data bits per time slot
001b = 16 data bits per time slot
010b = 18 data bits per time slot
011b = 20 data bits per time slot
100b = 24 data bits per time slot
101b = 32 data bits per time slot
110b = reserved
2:0
TSSL(2:0)
Time slot length
The time slot length bits are set by the MCU to program the number of serial clock
(CSCLK2) cycles for all time slots except time slot 0.
000b = 8 CSCLK cycles per time slot
001b = 16 CSCLK cycles per time slot
010b = 18 CSCLK cycles per time slot
011b = 20 CSCLK cycles per time slot
100b = 24 CSCLK cycles per time slot
101b = 32 CSCLK cycles per time slot
110b = reserved
111b= reserved
A–34
A.5.4.12 Codec Port Receive Interface Configuration Register 3 (CPTRXCNF3 – Address FFD5h)
The codec port receive interface configuration register3 is only used in I2S Mode 5.
Bit
Mnemonic
Type
7
6
5
4
3
2
1
0
DDLY
TRSEN
CSCLKP
CSYNCP
CSYNCL
BYOR
CSCLKD
CSYNCD
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
0
0
1
1
0
0
0
0
Default
BIT
MNEMONIC
NAME
DESCRIPTION
7
DDLY
Data delay
The data delay bit is set to 1 by the MCU to program a one CSCLK2 cycle delay of the serial data
output and input signals in reference to the leading edge of the CSYNC2 signal. The MCU must
clear this bit to a 0 for no delay between these signals.
6
TRSEN
Tri-state enable
The 3-state enable bit is set to a 1 by the MCU to program the hardware to 3-state the serial data
output signal for time slots during the audio frame that are not valid. The MCU must clear this bit to
a 0 to program the hardware to use zero-padding for the serial data output signal for time slots
during the audio frame that are not valid.
5
CSCLKP
CSCLK polarity
The CSCLK2 polarity bit is used by the MCU to program the clock edge used for the codec Port
Interface Frame Sync (CSYNC2) output signal and codec Port Interface Serial Data Input
(CDAT() signal. When this bit is set to a 1, the CSYNC2 signal is generated with the negative edge
of the codec Port Interface Serial Clock (CSCLK2) signal. Also, when this bit is set a 1, the CDATI
signal is sampled with the positive edge of the CLSCLK2 signal. When this bit is cleared to 0, the
CDATI signal is sampled with the negative edge of the CSCLK2 signal.
4
CSYNCP
CSYNC polarity
The CSCLK2 polarity bit is set to a 1 by the MCU to program the polarity of the codec Port Interface
Frame Sync (CSYNC2) output signal to be active high. The MCU must clear this bit to a 0 to
program the polarity of the CSYNC2 output signal to be active low.
3
CSYNCL
CSYNC length
The CSCLK2 polarity bit is set to a 1 by the MCU to program the polarity of the codec Port Interface
Frame Sync (CSYNC2) output signal to be the same number of CSCLK cycles as time slot 0. The
MCU must clear this bit to a 0 to program the length of the CSYNC2 output signal to be one
CSCLK2 cycle.
2
BYOR
Byte order
The byte order bit is used by the MCU to program the byte order for the data moved by the DMA
between the USB end-point buffer and the codec port interface. When this bit is set to a 1, the byte
order of each audio sample is reversed when the data is moved to/from the USB end-point buffer.
When this bit is cleared to a 0, the byte order of the each audio sample is unchanged.
1
CSCLKD
CSCLK direction
The CSCLK2 direction bit is set to a 1 by the MCU to program the direction of the codec port
interface serial clock (CSCLK2) signal as an input of the TAS1020 device. The MCU must clear
this bit to a 0 to program the direction of the CSCLK signal as an output from the TAS1020 device.
0
CSYNCD
CSYNC direction
The CSCLK2 direction bit is set to a 1 by the MCU to program the direction of the codec port
interface frame sync (CSYNC2) signal as an input of the TAS1020 device. The MCU must clear
this bit to a 0 to program the direction of the CSYNC2 signal as an output from the TAS1020
device.
A–35
A.5.4.13 Codec Port Receive Interface Configuration Register 4 (CPTRXCNF4 – Address FFD4h)
The codec port receive interface configuration register4 is only used in I2S Mode 5.
Bit
7
6
5
4
3
2
1
0
Mnemonic
–
–
–
–
–
DIVB2
DIVB1
DIVB0
Type
R
R
R
R
R
R/W
R/W
R/W
Default
0
0
0
0
0
0
0
0
BIT
2:0
A.5.5
MNEMONIC
NAME
DIVB(2:0)
Divide by B value
DESCRIPTION
The divide by B control bits are set by the MCU to program the CSCLK2 signal divider.
000b = disabled
001b = divide by 2
010b = divide by 3
011b = divide by 4
100b = divide by 5
101b = divide by 6
110b = divide by 7
111b = divide by 8
P3 Mask Register
Mask register for P3 to enable the wake-up function for these pins when the device is in low-power mode.
A.5.5.1 P3 Mask Register (P3MSK–Address FFCAh)
Bit
Mnemonic
7
6
5
4
3
2
1
0
P3MSK7
P3MSK6
P3MSK5
P3MSK4
P3MSK3
P3MSK2
P3MSK1
P3MSK0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
0
0
0
0
0
0
0
0
Type
Default
BIT
7:0
A.5.6
MNEMONIC
NAME
P3MSK(7:0)
DESCRIPTION
0 = Unmasked
1 = Masked
I2C Interface Registers
This section describes the memory-mapped registers used for the I2C Interface control and operation. The I2C
interface has a set of four registers. See section 2.2.17 for the operation details of the I2C Interface.
A.5.6.1 I2C Interface Address Register (I2CADR – Address FFC3h)
The I2C interface address register contains the 7-bit I2C slave device address and the read/write transaction control
bit.
Bit
Mnemonic
Type
7
6
5
4
3
2
1
0
A6
A5
A4
A3
A2
A1
A0
RW
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
0
0
0
0
0
0
0
0
Default
BIT
7:1
0
A–36
MNEMONIC
NAME
A(6:0)
Address
RW
Read/w3rite control
DESCRIPTION
The address bit values are set by the MCU to program the 7-bit I2C slave address of the device
to be accessed. Each I2C slave device must have a unique address on the I2C bus. This
address is used to identify the device on the bus to be accessed and is not the internal memory
address to be accessed within the device.
The read/write control bit value is set by the MCU to program the type of I2C transaction to be
done. This bit must be set to a 1 by the MCU for a read transaction and cleared to a 0 by the
MCU for a write transaction.
A.5.6.2 I2C Interface Receive Data Register (I2CDATI – Address FFC2h)
The I2C interface receive data register contains the most recent data byte received from the slave device.
Bit
7
6
5
4
3
2
1
0
RXD7
RXD6
RXD5
RDXD4
RXD3
RXD2
RXD1
RXD0
Type
R
R
R
R
R
R
R
R
Default
0
0
0
0
0
0
0
0
Mnemonic
BIT
7
MNEMONIC
NAME
RXD(7:0)
Receive data
DESCRIPTION
The receive data byte value is updated by hardware for each data byte received from the I2C
slave device.
A.5.6.3 I2C Interface Transmit Data Register (I2CDATO – Address FFC1h)
The I2C interface transmit data register contains the next address or data byte to be transmitted to the slave device
in accordance with the protocol. Note that for both read and write transactions, the internal register or memory
address of the slave device being accessed must be transmitted to the slave device.
Bit
7
6
5
4
3
2
1
0
TXD7
TXD6
TXD5
TXD4
TXD3
TXD2
TXD1
TXD0
Type
W
W
W
W
W
W
W
W
Default
0
0
0
0
0
0
0
0
Mnemonic
BIT
7:0
MNEMONIC
TXD(7:0)
NAME
Transmit data
DESCRIPTION
The transmit data byte value is set by the MCU for each address or data byte to be transmitted to
the I2C slave device.
A–37
A.5.6.4 I2C Interface Control and Status Register (I2CCTL – Address FFC0h)
The I2C interface control and status register contains various control and status bits used for the I2C interface
operation.
Bit
Mnemonic
7
6
5
4
3
2
1
0
RXF
RXIE
ERR
FRQ
TXE
TXIE
STPRD
STPWR
Type
R
R/W
R/W
R/W
R
R/W
R/W
R/W
Default
0
0
0
0
0
0
0
0
BIT
MNEMONIC
NAME
DESCRIPTION
7
RXF
Receive data register full
6
RXIE
Receive interrupt enable
5
ERR
Error condition
4
FRQ
Frequency select
3
TXE
Transmit data register empty
2
TXIE
Transmit interrupt enable
1
STPRD
Stop – read transaction
The stop read transaction bit is set to a 1 by the MCU to enable the hardware to
generate a stop condition on the I2C bus after the next data byte from the slave
device is received into the receive data register. The MCU must clear this bit to a 0
after the read transaction has concluded.
0
STPWR
Stop – write transaction
The stop write transaction bit is set to a 1 by the MCU to enable the hardware to
generate a stop condition on the I2C bus after the data byte in the transmit data
register is sent to the slave device. The MCU must clear this bit to a 0 after the write
transaction has concluded.
A–38
The receive data register full bit is set to a 1 by hardware when a new data byte has
been received into the receive data register from the slave device. This bit is read
only and is cleared to a 0 by hardware when the MCU reads the new byte from the
receive data register. Note that when the MCU writes to the interrupt vector register,
the I2C receive data register full interrupt is cleared but this status bit is not cleared at
that time.
The receive interrupt enable bit is set to a 1 by the MCU to enable the I2C receive
data register full interrupt.
The error condition bit is set to a 1 by hardware when the slave device does not
respond. This bit is read/write and can only be cleared by the MCU.
The frequency select bit is used by the MCU to program the I2C serial clock (SCL)
output signal frequency. A value of 0 sets the SCL frequency to 100 kHz and a value
of 1 sets the SCL frequency to 400 kHz.
The transmit data register empty bit is set to a 1 by hardware when the data byte in
the transmit data register has been sent to the slave device. This bit is read only and
is cleared to a 0 by hardware when a new data byte is written to the transmit data
register by the MCU. Note that when the MCU writes to the interrupt vector register,
the I2C transmit data register empty interrupt is cleared but this status bit is not
cleared at that time.
The transmit interrupt enable bit is set to a 1 by the MCU to enable the I2C transmit
data register empty interrupt.
A.5.7
Miscellaneous Registers
This section describes the memory-mapped registers used for the control and operation of miscellaneous functions
in the TAS1020 device. The registers include the USB out end-point interrupt register, the USB in end-point interrupt
register, the interrupt vector register, the global control register, and the memory configuration register.
A.5.7.1 USB Out End-Point Interrupt Register (OEPINT – Address FFB4h)
The USB out end-point interrupt register contains the interrupt pending status bits for the USB out end-points. These
bits do not apply to the USB isochronous end-points. Also, these bits are read only by the MCU and are used for
diagnostic purposes only.
Bit
Mnemonic
7
6
5
4
3
2
1
0
OEPI7
OEPI6
OEPI5
OEPI4
OEPI3
OEPI2
OEPI1
OEPI0
Type
R
R
R
R
R
R
R
R
Default
0
0
0
0
0
0
0
0
BIT
7:0
MNEMONIC
NAME
OEPI(7:0)
Out end-point interrupt
DESCRIPTION
The out end-point interrupt status bit for a particular USB out end-point is set to a 1 by the
UBM when a successful completion of a transaction occurs to that out end-point. When a
bit is set, an interrupt to the MCU will be generated and the corresponding interrupt vector
will result. The status bit is cleared when the MCU writes to the interrupt vector register.
These bits do not apply to isochronous out end-points.
A.5.7.2 USB In End-Point Interrupt Register (IEPINT – Address FFB3h)
The USB in end-point interrupt register contains the interrupt pending status bits for the USB in end-points. These
bits do not apply to the USB isochronous end-points. Also, these bits are read only by the MCU and are used for
diagnostic purposes only.
Bit
7
6
5
4
3
2
1
0
IEPI7
IEPI6
IEPI5
IEPI4
IEPI3
IEPI2
IEPI1
IEPI0
Type
R
R
R
R
R
R
R
R
Default
0
0
0
0
0
0
0
0
Mnemonic
BIT
7:0
MNEMONIC
IEPI(7:0)
NAME
In end-point interrupt
DESCRIPTION
The in end-point interrupt status bit for a particular USB in end-point is set to a 1 by the UBM
when a successful completion of a transaction occurs to that in end-point. When a bit is set,
an interrupt to the MCU is generated and the corresponding interrupt vector will result. The
status bit will be cleared when the MCU writes to the interrupt vector register. These bits do
not apply to isochronous in end-points.
A–39
A.5.7.3 Interrupt Vector Register (VECINT – Address FFB2H)
The interrupt vector register contains a 6-bit vector value that identifies the interrupt source for the INT0 input to the
MCU. All of the TAS1020 internal interrupt sources and the external interrupt input to the device are ORed together
to generate the internal INT0 signal to the MCU. When there is not an interrupt pending, the interrupt vector value
will be set to 24h. To clear any interrupt and update the interrupt vector value to the next pending interrupt, the MCU
should simply write any value to this register. The interrupt priority is fixed in order, ranging from vector value 1Fh with
the highest priority to vector value 00h with the lowest priority. An exception to this priority is the control endpoint EP0
which has top priority.
Bit
7
6
5
4
3
2
1
0
Mnemonic
—
—
IVEC5
IVEC4
IVEC3
IVEC2
IVEC1
IVEC0
Type
R
R
R
R
R
R
R
R
Default
0
0
0
0
0
0
0
0
BIT
MNEMONIC
NAME
DESCRIPTION
7
—
Reserved
Reserved for future use
6
—
Reserved
Reserved for future use
IVEC(5:0)
Interrupt vector
00h = USB out end-point 0
01h = USB out end-point 1
02h = USB out end-point 2
03h = USB out end-point 3
04h = USB out end-point 4
05h = USB out end-point 5
06h = USB out end-point 6
07h = USB out end-point 7
08h = USB in end-point 0
09h = USB in end-point 1
0Ah = USB in end-point 2
0Bh = USB in end-point 3
0Ch = USB in end-point 4
0Dh = USB in end-point 5
0Eh = USB in end-point 6
0Fh = USB in end-point 7
10h = USB setup stage transaction over-write
11h = Reserved
12h = USB setup stage transaction
13h = USB pseudo start-of-frame
14h = USB start-of-frame
15h = USB function resume
16h = USB function suspend
17h = USB function reset
18h = C-port receive data register full
19h = C-port transmit data register empty
1Ah = Reserved
1Bh = Reserved
1Ch = I2C receive data register full
1Dh = I2C transmit data register empty
1Eh = Reserved
1Fh = External interrupt input
20h = DMA Ch.0 interrupt
21h = DMA Ch.1 interrupt
22h - 23h = Reserved
24h = No interrupt pending
25h – 3Fh = Reserved
5:0
A–40
A.5.7.4 Global Control Register (GLOBCTL – Address FFB1h)
The global control register contains various global control bits for the TAS1020 device.
Bit
Mnemonic
Type
7
6
5
4
3
2
1
0
MCUCLK
XINTEN
P1PUDIS
VREN
RESET
LPWR
P3PUDIS
CPTEN
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
0
0
0
0
0
0
0
0
Default
BIT
MNEMONIC
NAME
DESCRIPTION
7
MCUCLK
MCU clock select
The MCU clock select bit is used by the MCU to program the clock frequency to be used for
the MCU operation.
0b = 12 MHz and 1b = 24 MHz
POR (Power On Reset) value is 0 (12 MHz). Setting this bit to 1 will change MCU clock
frequency to 24 MHz. But, once set, only cleared by master reset.
6
XINTEN
External interrupt enable
The external interrupt enable bit is set to a 1 by the MCU to enable the use of the external
interrupt input to the TAS1020 device.
5
P1PUDIS
Pull-up resistor disable
If set to 1, disables on-chip pullup resistors on P1 GPIO pins.
4
VREN
VREN
Memory-mapped GPIO pin.
3
RESET
RESET
Memory-mapped GPIO pin.
2
LPWR
Low power mode
The low power mode disable bit is used by the MCU to put the TAS1020 into a semi-low
power state. When this bit is cleared to a 0, all USB functional blocks are powered-down.
For normal operation, the MCU must set this bit to a 1.
1
P3PUDIS
Pull-up resistor disable
If set to 1, disables on-chip pullup resistors on P3 GPIO pins.
0
CPTEN
Codec port enable
The codec port enable bit is set to a 1 by the MCU to enable the operation of the codec port
interface. Note that the codec port interface configuration registers must be fully
programmed before this bit is set by the MCU.
A.5.7.5 Memory Configuration Register (MEMCFG – Address FFB0h)
The memory configuration register contains various bits pertaining to the memory configuration of the TAS1020
device.
Bit
Mnemonic
7
6
5
4
3
2
1
0
MEMTYP
CODESZ1
CODESZ0
REV3
REV2
REV1
REV0
SDW
Type
R
R
R
R
R
R
R
R/W
Default
1
0
1
0
0
0
0
0
BIT
MNEMONIC
NAME
DESCRIPTION
7
MEMTYP
Code memory type
The code memory type bit identifies if the type of memory used for the application program
code space is ROM or RAM. For the TAS1020, an 8K byte RAM is used and this bit is tied to 1.
6:5
CODESZ
Code space size
The code space size bits identify the size of the application program code memory space. For
the TAS1020, an 8K byte RAM is used and these bits are tied to 01b.
00b = 4K bytes, 01b = 8K bytes, 10b = 16K bytes, 11b = 32K bytes
4:1
REV
IC revision
The IC revision bits identify the revision of the IC.
0000b = Rev. -, 0001b = Rev. A, …, 1111b = Rev. F
0
SDW
Shadow the boot ROM
The shadow the boot ROM bit is set to a 1 by the MCU to switch the MCU memory
configuration from boot loader mode to normal operating mode. This must occur after
completion of the download of the application program code by the boot ROM.
Reference SDW protection bit in USBCTL register.
A–41
A–42
Appendix B
Mechanical Data
PFB (S-PQFP-G48)
PLASTIC QUAD FLATPACK
0,27
0,17
0,50
36
0,08 M
25
37
24
48
13
0,13 NOM
1
12
5,50 TYP
7,20
SQ
6,80
9,20
SQ
8,80
Gage Plane
0,25
0,05 MIN
0°– 7°
1,05
0,95
Seating Plane
1,20 MAX
0,75
0,45
0,08
4073176 / B 10/96
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
C. Falls within JEDEC MS-026
B–1
B–2
PACKAGE OPTION ADDENDUM
www.ti.com
30-Mar-2005
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
TAS1020PFB
OBSOLETE
TQFP
PFB
Pins Package Eco Plan (2)
Qty
48
TBD
Lead/Ball Finish
Call TI
MSL Peak Temp (3)
Call TI
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS) or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 1