Finisar Product Specification RoHS Compliant 80km Extended Reach GBIC Transceiver FTL-1519-3D Product Features • Up to 1.25Gb/s bi-directional data links • 1550nm DFB laser transmitter • Digital Diagnostics • Extended operating temperature range (0°C to +70°C) • Compatible with 3.3 & 5V systems • Hot-pluggable (complies with GBIC specification Rev. 5.5) • Fully metallic enclosure for low EMI • Low power dissipation • RoHS Compliant and Lead Free Applications • • 1.0625 Gb/s Fibre Channel 1.25 Gb/s Ethernet Finisar’s FTL-1519-3D 1550nm Extended GBIC transceivers have a maximum fiber length of 80km and comply with GBIC Specification Revision 5.51. They are compatible with Gigabit Ethernet as specified in IEEE 802.32, Fibre Channel FC-PH, PH2, PH33 and FC-PI-2 Rev. 104. They are RoHS-6 compliant per Directive 2002/95/EC5 and Finisar Application Note AN-20389. © Finisar Corporation November 16, 2007 Rev. B1 Page 1 FTL-1519-3D 80km Extended Reach GBIC Product Specification – November 2007 I. Finisar Pin Out Pin Name Pin # Sequence RX_LOS 1 2 GND 2 2 GND 3 2 MOD_DEF(0) 4 2 MOD_DEF(1) 5 2 MOD_DEF(2) 6 2 TX_DISABLE 7 2 GND 8 2 GND 9 2 TX_FAULT 10 2 GND 11 1 -RX_DAT 12 1 +RX_DAT 13 1 GND 14 1 VCC 15 2 VCC 16 2 GND 17 1 +TX_DAT 18 1 -TX_DAT 19 1 GND 20 1 Table 1. GBIC to host connector pin assignment “Sequence” indicates the order in which pins make contact when the device is hot plugged. See “Table 3: Signal Definitions” in the GBIC Specification Revision 5.5.1 for a description of the function of each pin list above. © Finisar Corporation November 16, 2007 Rev. B1 Page 2 FTL-1519-3D 80km Extended Reach GBIC Product Specification – November 2007 II. Finisar Electrical Power Interface Finisar FTL-1519-3D GBICs have an extended power supply voltage range of 3.15 V to 5.5 V as described in Table 2. They are compatible with both 3.3V and 5V systems. Parameter Symbol Min Supply Current Inrush Current Is Isurge Absolute Supply Voltage Vmax -0.3 Operating Supply Voltage Vcc 3.15 Typ Max Units 200 300 30 mA mA 6 V 5.5 V 3.3, 5 Notes/Conditions Hot plug, above steady state current. Not to be applied continuosly Referenced to GND Table 2. Electrical power interface III. Low Speed Signals RX_LOS and TX_DISABLE are TTL signals as described in Table 3. MOD_DEF(1) (SCL) and MOD_DEF(2) (SDA), are open drain CMOS signals (see section VIII, “Serial Communication Protocol”). Both MOD_DEF(1) and MOD_DEF(2) must be pulled up to host_Vcc. For more detailed information, see sections 5.3.1 – 5.3.8 in the GBIC Specification Rev. 5.51. Parameter GBIC Output LOW GBIC Output HIGH GBIC Input LOW GBIC Input HIGH Symbol Min Max VOL 0 0.5 Units Notes/Conditions 4.7k to 10k pull-up to host_Vcc, measured at host side of connector VOH host_Vcc - 0.5 host_Vcc + 0.3 V 4.7k to 10k pull-up to host_Vcc, measured at host side of connector VIL 0 0.8 V 4.7k to 10k pull-up to Vcc, measured at GBIC side of connector VIH 2 Vcc + 0.3 V 4.7k to 10k pull-up to Vcc, measured at GBIC side of connector Table 3. Low speed signals – electronic characteristics © Finisar Corporation November 16, 2007 Rev. B1 V Page 3 FTL-1519-3D 80km Extended Reach GBIC Product Specification – November 2007 Parameter Symbol Min Typ Max RX_LOS Assert Level RX_LOS Deassert Level RX_LOS Hysteresis RX_LOS Assert Delay --34 --0.5 t_loss_on 100 RX_LOS Negate Delay t_loss_off 100 TX_DISABLE Assert Time t_off 10 TX_DISABLE Negate Time t_on 1000 -24 TX_DISABLE Reset Time t_reset 10 TX_FAULT Initialize Time t_init 300 TX_FAULT Assert Time t_fault 100 Finisar Units Notes/Conditions dBm dBm dB µsec From detection of loss of signal to assertion of RX_LOS µsec From detection of presence of signal to negation of RX_LOS µsec Rising edge of TX_DISABLE to fall of output signal below 10% of nominal µsec Falling edge of TX_DISABLE to rise of output signal above 90% of nominal µsec TX_DISABLE HIGH before TX_DISABLE set LOW msec From power on after VCC > 4.5V µsec From occurrence of fault Table 4. Low speed signal parameters IV. High Speed Electrical Interface All high-speed PECL signals are AC-coupled internally. Parameter Data Input Voltage Data Output Voltage PECL rise/fall Bit Error Rate Tx Input Impedance Rx Output Impedance Symbol Min Vin Vout tr,tf BER Zin Zout 650 370 Typ 75 75 Max Units Notes/Conditions 2000 2000 260 10-12 mV mV psec PECL differential peak - peak PECL differential peak - peak 20%-80% differential PRBS 27 - 1 test data pattern Ohm Ohm Table 5. High-speed electrical interface © Finisar Corporation November 16, 2007 Rev. B1 Page 4 FTL-1519-3D 80km Extended Reach GBIC Product Specification – November 2007 V. Finisar Optical Parameters Parameter Symbol TRANSMITTER CHARACTERISTICS Transmitter Center Wavelength λc Side Mode Suppression Ratio SMSR Spectral Width (-20dB) σ Transmitter Optical Output Power Pout Min Typ 1540 30 Max 1570 1 +4 0 Transmitter Extinction Ratio Transmitter Eye Mask Margin ER -- Transmitter Rise/Fall Time tr /tf 260 RIN 160 -120 2 Total Transmitter Jitter Relative Intensity Noise Dispersion Penalty at 80km RECEIVER CHARACTERISTICS Optical Input Wavelength Receiver Reflectance Optical Input Power λin RRX Pin 9 20 1260 Units Notes/Conditions nm dB nm dBm Average power coupled into single mode fiber dB % Conforms to IEEE 802.3 and Fibre Channel Eye Masks ps 20%-80% differential unfiltered ps Peak to peak, filtered dB / Hz dB With SMF-28 fiber 1610 -14 -1 nm dB -24 dBm BER < 10-12 w/ PRBS 27 - 1 test pattern @ 1.25Gb/s Total Receiver Jitter 160 ps Peak to peak, filtered in loopback Note: Parameters are specified over temperature and voltage, at end of life unless otherwise noted. Table 6. Optical parameters VI. General Specifications Parameter Data Rate Symbol Min BR Typ Max Units Notes/Conditions 1.25 1.0625 Gb/sec Fibre Channel, IEEE 802.3 Compatible Fiber Length* L 0 80 km 9μm Core Single Mode Fiber Total System Budget -24 dB *Fiber loss budget plus all other system penalties must not exceed 24 dB. Table 7. General specifications © Finisar Corporation November 16, 2007 Rev. B1 Page 5 FTL-1519-3D 80km Extended Reach GBIC Product Specification – November 2007 Finisar VII. Environmental Specifications Parameter Operating Temp Relative Humidity Storage Temp Eye Safety Symbol Min Top RH Tsto -- 0 0 -40 Typ Max 70 85 85 Units Notes/Conditions °C % °C Case Temperature Non Condensing CDRH and IEC-825 Class 1 Laser Product. See Note 1 Note 1: Complies with FDA performance standards for laser products except for deviations pursuant to Laser Notice No. 50, dated July 26, 2001. Table 8. Environmental specifications VIII. Serial Communication Protocol All Finisar optical GBICs implement serial identification features described for ‘Module Definition “4”’ as outlined in Annex D of the GBIC Specification1. These GBICs use an Atmel AT24C01A 128 byte E2PROM at address A0H. For details on interfacing with the E2PROM, see the Atmel data sheet titled “AT24C01A/02/04/08/16 2-Wire Serial CMOS E2PROM.”6 The FTL-1519-3D also supports extended diagnostic features as described in Finisar Applications Note AN-2030, “Digital Diagnostic Monitoring Interface for Optical Transceivers”8, and additional information is available in SFF standard titled: “Digital Diagnostic Monitoring Interface for Optical Transceivers”7 (SFF-8472 rev9.3). A controller IC that monitors system parameters such as laser current, module temperature, transmitter power, and received power is accessible at address A2H. I2C clock speed, digital diagnostic accuracy and digital diagnostic range can be found in the table below. Values in the table represent the worst-case values over temperature, voltage, and life. © Finisar Corporation November 16, 2007 Rev. B1 Page 6 FTL-1519-3D 80km Extended Reach GBIC Product Specification – November 2007 Parameter I2C Clock Speed Accuracy Internal Transceiver Temperature Internal Transceiver Supply Voltage Tx Bias Current Tx Output Power Received Average Power Range Internal Transceiver Temperature Internal Transceiver Supply Voltage Tx Bias Current Tx Output Power Received Average Power Symbol Min Typ Max Finisar Units Notes/Conditions 0 100,000 Hz Bus can be driven blind DDTemperature -3 +3 °C Measured at controller IC DDVoltage -3 +3 % Measured at controller IC DDBias DDTxPower -10 -3 +10 +3 % dB DDRxPower -3 +3 dB DDTemperature -40 85 °C DDVoltage 3.0 6.0 V DDBias DDTxPower DDRxPower 0 -3 -24 100 5 -1 mA dBm dBm 100% tested in production tested at room temp to ±2 dB 100% tested in production tested at room temp to ±2 dB Table 9. Digital Diagnostic Accuracy and Range Limits © Finisar Corporation November 16, 2007 Rev. B1 Page 7 FTL-1519-3D 80km Extended Reach GBIC Product Specification – November 2007 IX. Finisar Mechanical Specifications Finisar GBICs are compatible with the mechanical specifications outlined in the GBIC Specification Revision 5.5, Section 61. Insertion, Extraction, and Retention Forces Parameter GBIC insertion GBIC extraction GBIC retention Symbol Min Typ Max Units Notes/Conditions FI 0 20 Newtons ~4.5 lbs FE 0 15 Newtons ~3.3 lbs FR 130 N/A Newtons Straight out ~29.3 lbs Table 10. Insertion, extraction, and retention forces Figure 1. GBIC outline drawing © Finisar Corporation November 16, 2007 Rev. B1 Page 8 FTL-1519-3D 80km Extended Reach GBIC Product Specification – November 2007 Finisar X. References 1. “Gigabit Interface Converter (GBIC) Revision 5.5”. Sun Microsystems Computer Company et. al., August 16, 1999. http://playground.sun.com/pub/OEmod/ 2. IEEE Std 802.3. IEEE Standards Department, 2002. 3. “Fibre Channel Physical and Signaling Interface (FC-PH, FC-PH2, FC-PH3)”. American National Standard for Information Systems. 4. “Fibre Channel Draft Physical Interface Specification (FC-PI-2 Rev. 10). American National Standard for Information Systems. 5. Directive 2002/95/EC of the European Council Parliament and of the Council, “on the restriction of the use of certain hazardous substances in electrical and electronic equipment.” January 27, 2003. 6. “AT24C01A/02/04/08/16 2-Wire Serial CMOS E2PROM”. Atmel Corporation. www.Atmel.com 7. “Digital Diagnostics Monitoring Interface for Optical Transceivers”. SFF Document Number SFF-8472, Revision 9.3. 8. “Application Note AN-2030: Digital Diagnostic Monitoring Interface for Optical Transceivers”, Finisar Corporation, April 2002. 9. “Application Note AN-2038: Finisar Implementation of RoHS Compliant Transceivers”, Finisar Corporation, March 2005. * The GBIC Standard, FC-PI-2 and IEEE 802.3 do not specify an 80km single-mode interface. The FTL-1519-3D complies with these standards expect for the following optical parameters: laser wavelength, receiver sensitivity and transmit output power. See Table 6 for details. XI. For More Information Finisar Corporation 1389 Moffett Park Drive Sunnyvale, CA 94089-1133 Tel. 1-408-548-1000 Fax 1-408-541-6138 [email protected] www.finisar.com © Finisar Corporation November 16, 2007 Rev. B1 Page 9