HMC356LP3 / 356LP3E v03.0610 AMPLIFIERS - LOW NOISE - SMT 7 GaAs PHEMT MMIC LOW NOISE AMPLIFIER, 350 - 550 MHz Typical Applications Features The HMC356LP3 / HMC356LP3E is ideal for basestation receivers: Noise Figure: ≤1.0 dB • GSM 450 & GSM 480 Gain: 17 dB • CDMA 450 Very Stable Gain vs. Supply & Temperature • Private Land Mobile Radio Single Supply: +5V @ 104 mA +38 dBm Output IP3 50 Ohm Matched Output Functional Diagram General Description The HMC356LP3 & HMC356LP3E are high dynamic range GaAs PHEMT MMIC Low Noise Amplifiers is ideal for GSM & CDMA cellular basestation and Mobile Radio front-end receivers operating between 350 and 550 MHz. This LNA has been optimized to provide 1.0 dB noise figure, 17 dB gain and +38 dBm output IP3 from a single supply of +5V @ 104 mA. Input and output return losses are 15 dB typical, with the LNA requiring only four external components to optimize the RF input match, RF ground and DC bias. For applications which require improved noise figure, please see the HMC616LP3(E). Electrical Specifi cations, TA = +25° C, Vs = +5V Parameter Min. Frequency Range Gain 15 Gain Variation Over Temperature Max. Units MHz 17 dB 0.0032 0.010 Noise Figure 1.0 1.4 Input Return Loss 17 dB Output Return Loss 12 dB Reverse Isolation Output Power for 1dB Compression (P1dB) 17 Saturated Output Power (Psat) Output Third Order Intercept (IP3) (-20 dBm Input Power per tone, 1 MHz tone spacing) Supply Current (Idd) 7 - 46 Typ. 350 - 550 34 dB / °C dB 24 dB 21 dBm 22.5 dBm 38 dBm 104 mA For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC356LP3 / 356LP3E v03.0610 GaAs PHEMT MMIC LOW NOISE AMPLIFIER, 350 - 550 MHz 1.5 20 1.4 15 1.3 10 5 S21 S11 S22 -5 -10 1.1 1 0.9 0.8 0.7 -20 0.6 0.25 0.5 0.75 1 1.25 1.5 FREQUENCY (GHz) 1.75 0.5 0.3 2 1.4 18 1.3 NOISE FIGURE (dB) 1.5 19 17 16 15 +25 C +85 C -40 C 13 0.5 0.55 0.6 0.55 0.6 0.55 0.6 1 0.9 0.8 0.7 0.6 10 0.4 0.45 0.5 FREQUENCY (GHz) 0.55 0.5 0.3 0.6 +4.5 V +5.0 V +5.5 V 1.1 11 0.35 0.45 1.2 12 0.3 0.4 Noise Figure vs. Vdd 20 14 0.35 FREQUENCY (GHz) Gain vs. Temperature GAIN (dB) 1.2 -15 -25 +25 C +85 C -40 C 0.35 0.4 0.45 0.5 AMPLIFIERS - LOW NOISE - SMT 25 0 7 Noise Figure vs. Temperature NOISE FIGURE (dB) RESPONSE (dB) Broadband Gain & Return Loss FREQUENCY (GHz) Reverse Isolation Gain vs. Vdd 0 20 19 -5 18 ISOLATION (dB) GAIN (dB) 17 16 15 14 +5.0 V +4.5 V +5.5 V 13 12 +25 C +85 C -40 C -10 -15 -20 -25 11 10 0.3 -30 0.35 0.4 0.45 0.5 FREQUENCY (GHz) 0.55 0.6 0.3 0.35 0.4 0.45 0.5 FREQUENCY (GHz) For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 7 - 47 HMC356LP3 / 356LP3E v03.0610 Output Return Loss vs. Temperature 0 0 -5 -5 RETURN LOSS (dB) RETURN LOSS (dB) Input Return Loss vs. Temperature +25 C +85 C -40 C -10 -15 -20 0.3 0.4 0.45 0.5 FREQUENCY (GHz) 0.55 0.6 0.3 25 40 24 COMPRESSION (dBm) 26 41 39 38 37 36 35 0.4 0.45 0.5 FREQUENCY (GHz) 0.55 20 19 +25 C +85 C -40 C P1dB 0.35 0.4 0.45 0.55 0.6 0.55 0.6 P1dB vs. Vdd 26 25 40 24 39 38 37 36 +4.5 V +5.0 V +5.5 V 23 22 21 20 19 18 33 +4.5 V +5.0 V +5.5 V 17 32 0.35 0.5 FREQUENCY (GHz) COMPRESSION (dBm) OUTPUT IP3 (dBm) 21 41 0.3 PSAT 22 42 34 0.6 23 16 0.3 0.6 Output IP3 vs. Vdd 35 0.55 17 32 0.35 0.4 0.45 0.5 FREQUENCY (GHz) 18 +25 C +85 C -40 C 33 0.35 P1dB & Psat vs. Temperature 42 34 7 - 48 -15 -25 0.35 Output IP3 vs. Temperature 0.3 +25 C +85 C -40 C -10 -20 -25 OUTPUT IP3 (dBm) AMPLIFIERS - LOW NOISE - SMT 7 GaAs PHEMT MMIC LOW NOISE AMPLIFIER, 350 - 550 MHz 0.4 0.45 0.5 FREQUENCY (GHz) 0.55 0.6 16 0.3 0.35 0.4 0.45 0.5 FREQUENCY (GHz) For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC356LP3 / 356LP3E v03.0610 GaAs PHEMT MMIC LOW NOISE AMPLIFIER, 350 - 550 MHz Typical Supply Current vs. Vdd Drain Bias Voltage (Vdd) +8.0 Vdc Vdd (Vdc) Idd (mA) RF Input Power (RFIN)(Vdd = +5.0 Vdc) +15 dBm +4.5 103 Channel Temperature 150 °C +5.0 104 Continuous Pdiss (T = 85 °C) (derate 14 mW/°C above 85 °C) 0.910 W +5.5 105 Thermal Resistance (channel to ground paddle) 71.4 °C/W Storage Temperature -65 to +150 °C Operating Temperature -40 to +85 °C ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS Outline Drawing 7 AMPLIFIERS - LOW NOISE - SMT Absolute Maximum Ratings NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS] 3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE 4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM. PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM. 5. PACKAGE WARP SHALL NOT EXCEED 0.05mm. 6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. 7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED LAND PATTERN. Package Information Part Number Package Body Material Lead Finish MSL Rating HMC356LP3 Low Stress Injection Molded Plastic Sn/Pb Solder MSL1 HMC356LP3E RoHS-compliant Low Stress Injection Molded Plastic 100% matte Sn MSL1 Package Marking [3] [1] 356 XXXX [2] 356 XXXX [1] Max peak reflow temperature of 235 °C [2] Max peak reflow temperature of 260 °C [3] 4-Digit lot number XXXX For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 7 - 49 HMC356LP3 / 356LP3E v03.0610 AMPLIFIERS - LOW NOISE - SMT 7 GaAs PHEMT MMIC LOW NOISE AMPLIFIER, 350 - 550 MHz Pin Descriptions Pin Number Function Description Interface Schematic 1, 5, 8, 9, 10, 12, 13, 14 N/C No connection necessary. These pins may be connected to RF/DC ground. 2, 4, 6,16 GND These pins and package ground paddle must be connected to RF/DC ground. 3 RFIN This pin is matched to 50 Ohms with a 51 nH inductor to ground. See Application Circuit. 7 ACG AC Ground - An external capacitor of 0.01μF to ground is required for low frequency bypassing. See Application Circuit for further details. 11 RFOUT This pin is AC coupled and matched to 50 Ohms. 15 Vdd Power supply voltage. Choke inductor and bypass capacitor are required. See application circuit. Application & Evaluation PCB Circuit Note 1: Choose value of capacitor C1 for low frequency bypassing. A 0.01 μF ±10% capacitor is recommended. Note 2: L1, L2 and C1 should be located as close to pins as possible. 7 - 50 For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC356LP3 / 356LP3E v03.0610 GaAs PHEMT MMIC LOW NOISE AMPLIFIER, 350 - 550 MHz 7 AMPLIFIERS - LOW NOISE - SMT Evaluation PCB List of Materials for Evaluation PCB 107795 [1] Item Description J1 - J2 PCB Mount SMA RF Connector J3 - J4 DC Pin C1 10,000 pF Capacitor, 0402 Pkg. C2 10,000 pF Capacitor, 0603 Pkg. L1 51 nH Inductor, 0402 Pkg. L2 36 nH Inductor, 0603 Pkg. U1 HMC356LP3 / HMC356LP3E Amplifier PCB [2] 106722 Evaluation PCB The circuit board used in the application should use RF circuit design techniques. Signal lines should have 50 Ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350 For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 7 - 51