HMC485MS8G / 485MS8GE v03.0507 HIGH IP3 GaAs MMIC MIXER with INTEGRATED LO AMPLIFIER, 1.7 - 2.4 GHz Typical Applications Features High Dynamic Range Infrastructure: +34 dBm Input IP3 • GSM, GPRS & EDGE Conversion Loss: 9 dB • CDMA & W-CDMA Low LO Drive: -2 to +4 dBm • Cable Modem Termination Systems Single Positive Supply: 5V @ 45 mA Ultra Small MSOP Package: 14.8mm2 MIXERS - HIGH IP3 - SMT 9 Included in the HMC-DK003 Designer’s Kit Functional Diagram General Description The HMC485MS8G & HMC485MS8GE are high dynamic range passive MMIC mixers with integrated LO amplifier in plastic surface mount 8 lead Mini Small Outline Packages (MSOP) covering 1.7 to 2.4 GHz. Excellent input IP3 performance of +34 dBm for down conversion and +27 dBm for up conversion is provided for 2.5G & 3G GSM/CDMA based UMTS or PCS applications at an LO drive of 0 dBm. With an input 1 dB compression of +19 dBm, the RF port will accept a wide range of input signal levels. Conversion loss is 9.2 dB typical. The 50 to 300 MHz IF frequency response will satisfy many UMTS/ PCS transmit or receive frequency plans configured for low side LO. The HMC485MS8G(E) input IP3 performance coupled with its high P1dB rivals traditional active FET mixers while offering a much smaller 14.8mm2 standard IC footprint. Electrical Specifi cations, TA = +25°C, LO = 0 dBm, IF = 200 MHz*, Vdd= 5V Parameter Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. Min. Typ. Max 1.7 - 1.8 1.8 - 2.0 2.0 - 2.2 2.2 - 2.4 Frequency Range, LO 1.4 - 1.75 1.5 - 1.95 1.7 - 2.15 1.9 - 2.35 GHz Frequency Range, IF 50 - 300 50 - 300 50 - 300 50 - 300 MHz 9.8 Noise Figure (SSB) 9.8 9.2 9 9.5 dB LO to RF Isolation 12 8 5 5 dB 27 1 dB Gain Compression (Input) 16 Supply Current 9.2 7 IP3 (Input) LO Input Drive Level (Typical) 11 10.5 9 10 31 29 19 17 10 9.5 GHz Conversion Loss LO to IF Isolation 13 34 29 20 17 33 29 21 18.5 10.5 dB 12 dB 32 dBm 21.5 dBm -2 to +4 -2 to +4 -2 to +4 -2 to +4 dBm 45 45 45 45 mA *Unless otherwise noted, all measurements performed as a downconverter, with low side LO & IF = 200 MHz. 9 - 292 Units Frequency Range, RF For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC485MS8G / 485MS8GE v03.0507 HIGH IP3 GaAs MMIC MIXER with INTEGRATED LO AMPLIFIER, 1.7 - 2.4 GHz Conversion Gain vs. Temperature @ LO = 0 dBm Isolation @ LO = 0 dBm 0 -5 -5 -10 + 25C -15 + 85C - 40C 1.8 1.9 2 2.1 2.2 2.3 2.4 RF TO IF LO TO RF LO TO IF -25 1.7 2.5 1.8 1.9 2.1 2.2 2.3 2.4 2.5 2.3 2.4 2.5 Return Loss @ LO = 0 dBm Conversion Gain vs. LO Drive 0 0 RF LO -8 -5 RETURN LOSS (dB) CONVERSION GAIN (dB) 2 FREQUENCY (GHz) RF FREQUENCY (GHz) -10 LO = -4 dBm LO = -2 dBm LO = 0 dBm LO = +2 dBm LO = +4 dBm -15 -20 1.7 1.8 1.9 2 2.1 2.2 -16 -24 -32 2.3 2.4 -40 1.7 2.5 1.8 1.9 2 2.1 2.2 FREQUENCY (GHz) RF FREQUENCY (GHz) Upconverter Performance Conversion Gain @ LO = 0 dBm IF Bandwidth @ LO = 0 dBm 0 0 -5 -5 RESPONSE (dB) CONVERSION GAIN (dB) 9 -15 -20 -20 1.7 -10 MIXERS - HIGH IP3 - SMT ISOLATION (dB) CONVERSION GAIN (dB) 0 -10 -15 CONVERSION GAIN RETURN LOSS -10 -15 -20 -20 1.7 1.8 1.9 2 2.1 2.2 RF FREQUENCY (GHz) 2.3 2.4 2.5 0 50 100 150 200 250 300 350 IF FREQUENCY (MHz) 400 450 500 *Unless otherwise noted, all measurements performed as a downconverter, with low side LO & IF = 200 MHz. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 9 - 293 HMC485MS8G / 485MS8GE v03.0507 HIGH IP3 GaAs MMIC MIXER with INTEGRATED LO AMPLIFIER, 1.7 - 2.4 GHz Input IP3 vs. LO Drive 40 35 35 INPUT IP3 (dBm) 40 30 + 25C + 85C - 40C 25 30 LO = -2dBm LO = 0dBm LO = +2dBm LO = +4dBm 25 20 20 1.7 1.8 1.9 2 2.1 2.2 FREQUENCY (GHz) 2.3 2.4 2.5 Input IP2 vs. Temperature @ LO= 0 dBm 1.7 45 45 40 40 35 30 + 25C - 40C + 85C 25 1.8 1.9 20 2.4 2.5 2.3 2.4 2.5 2.3 2.4 2.5 30 - 2 dBm 0 dBm + 2 dBm + 4 dBm 20 1.7 1.8 1.9 2 2.1 2.2 FREQUENCY (GHz) 2.3 2.4 2.5 1.7 1.8 1.9 40 - 2dBm 0dBm - 2dBm - 4dBm 23 INPUT IP3 (dBm) 35 21 19 + 25C + 85C - 40C 17 30 25 20 15 1.7 2 2.1 2.2 FREQUENCY (GHz) Upconverter IP3 vs. LO Drive, IF= 200 MHz 25 INPUT P1dB (dBm) 2.3 35 25 Input P1dB vs. Temperature @ LO= 0 dBm 9 - 294 2 2.1 2.2 FREQUENCY (GHz) Input IP2 vs. LO Drive @ IF= 200 MHz INPUT IP2 (dBm) INPUT IP2 (dBm) MIXERS - HIGH IP3 - SMT 9 INPUT IP3 (dBm) Input IP3 vs. Temperature @ LO= 0 dBm 1.8 1.9 2 2.1 2.2 2.3 FREQUENCY (GHz) 2.4 2.5 1.7 1.8 1.9 2 2.1 2.2 FREQUENCY (GHz) For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC485MS8G / 485MS8GE HIGH IP3 GaAs MMIC MIXER with INTEGRATED LO AMPLIFIER, 1.7 - 2.4 GHz Input IP3 vs. LO Drive, IF= 120 MHz 40 40 35 35 INPUT IP3 (dBm) INPUT IP3 (dBm) Input IP3 vs. LO Drive, IF= 70 MHz 30 - 2 dBm 0 dBm + 2 dBm + 4 dBm 25 20 1.8 1.9 2 2.1 2.2 FREQUENCY (GHz) 2.3 2.4 35 35 INPUT IP3 (dBm) 40 30 - 2 dBm 0 dBm + 2 dBm + 4 dBm 25 1.8 1.9 2 2.1 2.2 FREQUENCY (GHz) 2.3 2.4 2.5 Input IP3 vs. LO Drive, IF= 247 MHz 40 30 - 2 dBm 0 dBm + 2 dbm + 4 dBm 25 20 20 1.8 1.9 2 2.1 2.2 FREQUENCY (GHz) 2.3 2.4 2.5 1.7 1.8 1.9 2 2.1 2.2 FREQUENCY (GHz) 2.3 2.4 2.5 Input IP3 vs. LO Drive, IF= 297 MHz 40 35 INPUT IP3 (dBm) INPUT IP3 (dBm) 1.7 2.5 Input IP3 vs. LO Drive, IF= 170 MHz 1.7 9 - 2 dBm 0 dBm + 2 dBm + 4 dBm 25 20 1.7 30 MIXERS - HIGH IP3 - SMT v03.0507 30 - 2dBm 0 dBm + 2dBm + 4dBm 25 20 1.7 1.8 1.9 2 2.1 2.2 FREQUENCY (GHz) 2.3 2.4 2.5 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 9 - 295 HMC485MS8G / 485MS8GE v03.0507 HIGH IP3 GaAs MMIC MIXER with INTEGRATED LO AMPLIFIER, 1.7 - 2.4 GHz MxN Spurious Outputs Harmonics of LO nLO MIXERS - HIGH IP3 - SMT 9 9 - 296 mRF 0 1 2 0 xx -1. 19 1 4 0 30 2 54 69 39 3 75 82 4 78 82 nLO Spur at RF Port 4 LO Freq GHz 1 15 15 1.5 25 44 1.6 56 55 83 74 83 83 RF Freq = 1.9 GHz @ 0 dBm LO Freq = 1.7 GHz @ 0 dBm All values in dBc Relative to the IF power level. 3 2 3 4 19 15 35 24 17 15 33 24 1.7 14 14 29 23 72 1.8 10 15 25 24 82 1.9 8 20 22 23 2 6 20 22 24 LO power = 0 dBm All values in dBc below input LO level measured at RF port. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC485MS8G / 485MS8GE v03.0507 HIGH IP3 GaAs MMIC MIXER with INTEGRATED LO AMPLIFIER, 1.7 - 2.4 GHz Absolute Maximum Ratings +27 dBm LO Drive +10 dBm Bias Supply (Vdd) +7 Vdc Channel Temperature 150 °C Continuous Pdiss (T = 85°C) (Derate 13.2 mW/°C above 85°C) 0.85 W Storage Temperature -65 to +150 °C Operating Temperature -40 to +85 °C IF DC Current ±40 mA ESD Sensitivity (HBM) Class 1A ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS 9 MIXERS - HIGH IP3 - SMT RF/IF Input Outline Drawing NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS] 3. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.15mm PER SIDE. 4. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.25mm PER SIDE. 5. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. Package Information Part Number Package Body Material Lead Finish MSL Rating HMC485MS8G Low Stress Injection Molded Plastic Sn/Pb Solder MSL1 HMC485MS8GE RoHS-compliant Low Stress Injection Molded Plastic 100% matte Sn MSL1 Package Marking [3] [1] H485 XXXX [2] H485 XXXX [1] Max peak reflow temperature of 235 °C [2] Max peak reflow temperature of 260 °C [3] 4-Digit lot number XXXX For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 9 - 297 HMC485MS8G / 485MS8GE v03.0507 HIGH IP3 GaAs MMIC MIXER with INTEGRATED LO AMPLIFIER, 1.7 - 2.4 GHz Pin Descriptions MIXERS - HIGH IP3 - SMT 9 9 - 298 Pin Number Function Description 1 LO This pin is AC coupled and matched to 50 Ohms. 2 N/C Not connected. 3, 6, 7 GND This pin must be connected to RF ground. 4 Vdd Power supply for LO amplifier. An external RF bypass capacitor is required. 5 IF Port This pin is DC coupled. For applications not requiring operation to DC this port should be DC blocked externally using a series capacitor. Choose value of capacitor to pass IF frequency desired. For operation to DC, this pin must not sink/source more than 40 mA of current or failure may result. 8 RF Port This pin is DC coupled and matched to 50 Ohms. Interface Schematic For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC485MS8G / 485MS8GE v03.0507 HIGH IP3 GaAs MMIC MIXER with INTEGRATED LO AMPLIFIER, 1.7 - 2.4 GHz Evaluation PCB List of Materials for Evaluation PCB 105188 [1] Item Description J1 - J3 PCB Mount SMA RF Connector J4 - J5 DC Pin C1 10,000 pF Chip Capacitor, 0603 Pkg. U1 HMC485MS8G / HMC485MS8GE Mixer PCB [2] 104813 Evaluation Board, 1.0” x 1.0” [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350 The circuit board used in the final application should use RF circuit design techniques. Signal lines should have 50 ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com MIXERS - HIGH IP3 - SMT 9 9 - 299