HMC695LP4 / 695LP4E v01.1109 SMT GaAs HBT MMIC x4 ACTIVE FREQUENCY MULTIPLIER, 11.4 - 13.2 GHz OUTPUT Typical Applications Features The HMC695LP4(E) is ideal for: Output Power: +7 dBm • Fiber Optic Applications Sub-Harmonic Suppression: >25 dBc • Point-to-Point Radios SSB Phase Noise: -140 dBc/Hz • Military Radar Single Supply: +5V @ 60 mA 5 24 Lead 4x4 mm SMT Package: 16 mm2 FREQ. MULTIPLIERS - ACTIVE - SMT Functional Diagram General Description The HMC695LP4(E) are active miniature x4 frequency multipliers utilizing InGaP GaAs HBT technology in 4x4 mm leadless surface mount packages. Power output is +7 dBm typical from a +5V supply voltage and varies little vs. input power, temperature and supply voltage. Suppression of undesired fundamental and sub-harmonics is >25 dBc typical with respect to output signal level. The low additive SSB phase noise of -140 dBc/Hz at 100 kHz offset helps the user maintain good system noise performance. The HMC695LP4(E) are ideal for use in LO multiplier chains allowing reduced parts count vs. traditional approaches. Electrical Specifications, TA = +25° C, Vcc= 5V Parameter Min. Frequency Range, Input Frequency Range, Output Max. -15 Output Power GHz 5 dBm 7 dBm Sub-Harmonic Suppression 25 dBc Input Return Loss 15 dB Output Return Loss 8 dB SSB Phase Noise (100 kHz Offset) Supply Current (Icc) 2 Units GHz 11.4 - 13.2 Input Power Range 5-1 Typ. 2.85 - 3.3 Pin= 0 dBm -140 60 dBc/Hz 75 mA For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC695LP4 / 695LP4E v01.1109 SMT GaAs HBT MMIC x4 ACTIVE FREQUENCY MULTIPLIER, 11.4 - 13.2 GHz OUTPUT Output Power vs. Drive Level 10 10 8 8 6 +25 C +85 C -40 C 4 2 6 2 0 0 11 11.5 12 12.5 13 13.5 14 11 11.5 OUTPUT FREQUENCY (GHz) 12.5 13 13.5 14 Input Return Loss vs. Temperature 10 0 -5 RETURN LOSS (dB) 8 POWER (dBm) 12 OUTPUT FREQUENCY (GHz) Output Power vs. Supply Voltage @ -10 dBm Drive Level 6 Vcc=4.5V Vcc=5.0V Vcc=5.5V 4 2 +25 C +85 C -40 C -10 -15 -20 -25 0 -30 11 11.5 12 12.5 13 13.5 14 2 OUTPUT FREQUENCY (GHz) 2.5 3 Fout 1Fin 2Fin 3Fin OUTPUT POWER (dBm) 30 -5 -10 +25 C +85 C -40 C -20 8 10 12 FREQUENCY (GHz) 14 4 4.5 5 Harmonics @ -10 dBm Drive Level 0 -15 3.5 FREQUENCY (GHz) Output Return Loss vs. Temperature RETURN LOSS (dB) 5 -20 dBm -15 dBm -10 dBm -5 dBm 0 dBm +5 dBm 4 16 5Fin 6Fin 7Fin 8Fin FREQ. MULTIPLIERS - ACTIVE - SMT POWER (dBm) POWER (dBm) Output Power vs. Temperature @ -10 dBm Drive Level 10 -10 -30 -50 -70 2.75 3 3.25 3.5 INPUT FREQUENCY (GHz) For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 5-2 HMC695LP4 / 695LP4E v01.1109 SMT GaAs HBT MMIC x4 ACTIVE FREQUENCY MULTIPLIER, 11.4 - 13.2 GHz OUTPUT FREQ. MULTIPLIERS - ACTIVE - SMT 5-3 SSB Phase Noise @ Pin = -10 dBm @ 12.5 GHz 0 0 -20 -20 SSB PHASE NOISE (dBc/Hz) 5 SSB PHASE NOISE (dBc/Hz) SSB Phase Noise @ Pin = 0 dBm @ 12.5 GHz -40 -60 -80 -100 -120 -140 -160 2 10 3 4 10 10 5 10 6 10 7 10 -40 -60 -80 -100 -120 -140 -160 2 10 3 10 OFFSET FREQUENCY (Hz) Absolute Maximum Ratings 4 10 5 6 10 10 7 10 OFFSET FREQUENCY (Hz) Typical Supply Current vs. Vcc RF Input (Vcc= +5V) +20 dBm Vcc (V) Icc (mA) Vcc +5.5V 4.75 59 Channel Temperature 135 °C 5.00 60 Continuous Pdiss (T=85 °C) (derate 10.8 mW/°C above 85 °C) 538 mW 5.25 61 Thermal Resistance (Rth) (junction to ground paddle) 93 °C/W Storage Temperature -65 to +150 °C Operating Temperature -40 to +85 °C ESD Sensitivity (HBM) Class 1B Note: Multiplier will operate over full voltage range shown above. ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC695LP4 / 695LP4E v01.1109 SMT GaAs HBT MMIC x4 ACTIVE FREQUENCY MULTIPLIER, 11.4 - 13.2 GHz OUTPUT Outline Drawing NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS] 3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE. 4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM. PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM. 5. PACKAGE WARP SHALL NOT EXCEED 0.05mm. 6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. 7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED LAND PATTERN. Package Information Part Number Package Body Material Lead Finish MSL Rating HMC695LP4 Low Stress Injection Molded Plastic Sn/Pb Solder MSL1 [1] HMC695LP4E RoHS-compliant Low Stress Injection Molded Plastic 100% matte Sn MSL1 [2] Package Marking [3] H695 XXXX FREQ. MULTIPLIERS - ACTIVE - SMT 5 H695 XXXX [1] Max peak reflow temperature of 235 °C [2] Max peak reflow temperature of 260 °C [3] 4-Digit lot number XXXX For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] 5-4 HMC695LP4 / 695LP4E v01.1109 SMT GaAs HBT MMIC x4 ACTIVE FREQUENCY MULTIPLIER, 11.4 - 13.2 GHz OUTPUT Pin Description Pin Number FREQ. MULTIPLIERS - ACTIVE - SMT 5 5-5 Function Description 1, 2, 5 - 14, 17, 18, 20 - 24 N/C The pins are not connected internally; however, all data shown herein was measured with these pins connected to RF/DC ground externally. 3 RFIN RF input needs to be DC blocked only if there is an external DC voltage applied to RFIN. 4, 15 GND All ground leads and ground paddle must be soldered to PCB RF/DC ground. 16 RFOUT Multiplied Output. AC coupled. No external DC blocks necessary. 19 Vcc Supply voltage 5V Interface Schematic For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] HMC695LP4 / 695LP4E v01.1109 SMT GaAs HBT MMIC x4 ACTIVE FREQUENCY MULTIPLIER, 11.4 - 13.2 GHz OUTPUT Evaluation PCB List of Materials for Evaluation PCB 106137 Item Description J1 - J3 PCB Mount SMA Connector C1 1,000 pF Capacitor, 0603 Pkg. U1 HMC695LP4(E) x4 Active Multiplier PCB [2] 104610 Eval Board [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Arlon 25FR or Rogers 4350 [1] The circuit board used in the application should be generated with proper RF circuit design techniques. Signal lines should have 50 ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. The evaluation circuit board shown is available from Hittite upon request. For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com Application Support: Phone: 978-250-3343 or [email protected] FREQ. MULTIPLIERS - ACTIVE - SMT 5 5-6