HITTITE HMC370LP4E

HMC370LP4 / 370LP4E
v04.0110
SMT GaAs HBT MMIC x4 ACTIVE
FREQUENCY MULTIPLIER, 14.4 - 16.4 GHz OUTPUT
FREQ. MULTIPLIERS - ACTIVE - SMT
7
Typical Applications
Features
The HMC370LP4(E) is ideal for:
Output Power: 0 dBm
• Point-to-Point & VSAT Radios
Sub-Harmonic Suppression: >22 dBc
• Fiber Optic
SSB Phase Noise: -140 dBc/Hz
• Military
Single Supply: +5V @ 55 mA
24 Lead 4x4 mm SMT Package: 16 mm2
Functional Diagram
General Description
The HMC370LP4(E) is an active miniature x4 frequency multiplier utilizing InGaP GaAs HBT
technology in a 4x4 mm leadless surface mount
package. Power output is 0 dBm typical from a
5V supply voltage and varies little vs. input power,
temperature and supply voltage. Suppression of
undesired fundamental and sub-harmonics is >22
dBc typical with respect to output signal level. The
low additive SSB phase noise of -140 dBc/Hz at
100 kHz offset helps the user maintain good system noise performance. The HMC370LP4(E) are ideal
for use in LO multiplier chains allowing reduced parts
count vs. traditional approaches.
Electrical Specifi cations, TA = +25° C, Vcc = 5V
Parameter
Min.
Frequency Range, Input
Frequency Range, Output
Max.
-15
Output Power
-4
Units
GHz
14.4 - 16.4
Input Power Range
GHz
+5
dBm
0
dBm
Sub-Harmonic Suppression
22
dBc
Input Return Loss
18
dB
Output Return Loss
7
dB
SSB Phase Noise (100 kHz Offset)
Supply Current (Icc)
7 - 46
Typ.
3.6 - 4.1
Pin = 0 dBm
-140
55
dBc/Hz
73
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
mA
HMC370LP4 / 370LP4E
v03.0907
SMT GaAs HBT MMIC x4 ACTIVE
FREQUENCY MULTIPLIER, 14.4 - 16.4 GHz OUTPUT
Output Power vs. Drive Level
4
4
3
3
2
2
OUTPUT POWER (dBm)
1
0
-1
-2
-3
+25 C
+85 C
-40 C
-4
7
1
0
-1
-2
-20 dBm
-15 dBm
-10 dBm
-5 dBm
0 dBm
+5 dBm
-3
-4
-5
-5
-6
-6
14
14.4
14.8
15.2
15.6
16
16.4
16.8
14
14.4
OUTPUT FREQUENCY (GHz)
0
3
-5
RETURN LOSS (dB)
2
1
0
-1
-2
Vcc=4.5V
Vcc=5.0V
Vcc=5.5V
16
16.4
16.8
-10
-15
-20
-25
-30
+25 C
+85 C
-40 C
-35
-5
-40
-6
14
14.4
14.8
15.2
15.6
16
16.4
0
16.8
1
2
3
4
FREQUENCY (GHz)
OUTPUT FREQUENCY (GHz)
5
6
Output Return Loss vs. Temperature
0
-5
RETURN LOSS (dB)
OUTPUT POWER (dBm)
15.6
Input Return Loss vs. Temperature
4
-4
15.2
OUTPUT FREQUENCY (GHz)
Output Power vs.
Supply Voltage @ -10 dBm Drive Level
-3
14.8
FREQ. MULTIPLIERS - ACTIVE - SMT
OUTPUT POWER (dBm)
Output Power vs.
Temperature @ -10 dBm Drive Level
-10
-15
+25 C
+85 C
-40 C
-20
-25
8
9
10
11
12
13
14
15
16
17
18
FREQUENCY (GHz)
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
7 - 47
HMC370LP4 / 370LP4E
v03.0907
SMT GaAs HBT MMIC x4 ACTIVE
FREQUENCY MULTIPLIER, 14.4 - 16.4 GHz OUTPUT
SSB Phase Noise
Performance, Fout= 15.0 GHz
Output Spectrum
7 - 48
0
10
-20
SSB PHASE NOISE (dBc/Hz)
0
OUTPUT POWER (dBm)
FREQ. MULTIPLIERS - ACTIVE - SMT
7
-10
-20
-30
-40
-60
Pin = 0 dBm
Pin = -10 dBm
-80
-100
-40
-120
-140
-50
-160
-60
0
2
4
6
8
10
12
14
16
FREQUENCY (GHz)
18
20
22
24
26
10
2
10
3
10
4
10
5
10
OFFSET FREQUENCY (Hz)
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
6
10
7
HMC370LP4 / 370LP4E
v03.0907
SMT GaAs HBT MMIC x4 ACTIVE
FREQUENCY MULTIPLIER, 14.4 - 16.4 GHz OUTPUT
Typical Supply Current vs. Vcc
RF Input (Vcc = +5V)
+20 dBm
Vcc (V)
Icc (mA)
Vcc
+5.5V
4.5
54
Channel Temperature
135 °C
5.0
55
5.5
57
Continuous Pdiss (T=85 °C)
(derate 8.1 mW/°C above 85 °C)
530 mW
Thermal Resistance (Rth)
(junction to ground paddle)
123.6 °C/W
Storage Temperature
-65 to +150 °C
Operating Temperature
-40 to +85 °C
Note: Multiplier will operate over full voltage range shown
above.
ELECTROSTATIC SENSITIVE DEVICE
OBSERVE HANDLING PRECAUTIONS
Outline Drawing
7
FREQ. MULTIPLIERS - ACTIVE - SMT
Absolute Maximum Ratings
NOTES:
1. LEADFRAME MATERIAL: COPPER ALLOY
2. DIMENSIONS ARE IN INCHES [MILLIMETERS]
3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE.
4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM.
PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM.
5. PACKAGE WARP SHALL NOT EXCEED 0.05mm.
6. ALL GROUND LEADS AND GROUND PADDLE MUST BE
SOLDERED TO PCB RF GROUND.
7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED
LAND PATTERN.
Package Information
Part Number
Package Body Material
Lead Finish
MSL Rating
HMC370LP4
Low Stress Injection Molded Plastic
Sn/Pb Solder
MSL1
HMC370LP4E
RoHS-compliant Low Stress Injection Molded Plastic
100% matte Sn
MSL1
Package Marking [3]
[1]
H370
XXXX
[2]
H370
XXXX
[1] Max peak reflow temperature of 235 °C
[2] Max peak reflow temperature of 260 °C
[3] 4-Digit lot number XXXX
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
7 - 49
HMC370LP4 / 370LP4E
v03.0907
SMT GaAs HBT MMIC x4 ACTIVE
FREQUENCY MULTIPLIER, 14.4 - 16.4 GHz OUTPUT
Pin Description
FREQ. MULTIPLIERS - ACTIVE - SMT
7
7 - 50
Pin Number
Function
Description
1, 2, 5-14, 17,
18, 20-24
N/C
The pins are not connected internally; however, all
data shown herein was measured with these pins
connected to RF/DC ground externally.
3
RFIN
RF input needs to be DC blocked only if there is an
external DC voltage applied to RF IN.
4, 15
GND
All ground leads and ground paddle must be soldered
to PCB RF/DC ground.
16
RFOUT
Multiplied Output. AC coupled. No external DC blocks
necessary.
19
Vcc
Supply voltage 5V ± 0.5V.
Interface Schematic
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC370LP4 / 370LP4E
v03.0907
SMT GaAs HBT MMIC x4 ACTIVE
FREQUENCY MULTIPLIER, 14.4 - 16.4 GHz OUTPUT
Evaluation PCB
FREQ. MULTIPLIERS - ACTIVE - SMT
7
List of Materials for Evaluation PCB 106137 [1]
Item
Description
J1 - J3
PCB Mount SMA Connector
C1
1,000 pF Capacitor, 0603 Pkg.
U1
HMC370LP4(E) x4 Active Multiplier
PCB [2]
104610 Eval Board
[1] Reference this number when ordering complete evaluation PCB
[2] Circuit Board Material: Rogers 4350
The circuit board used in the application should
be generated with proper RF circuit design techniques. Signal lines should have 50 Ohm impedance while the package ground leads and exposed
paddle should be connected directly to the ground
plane similar to that shown. The evaluation circuit
board shown is available from Hittite upon request.
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
7 - 51