HMC860LP3E v01.0811 QUAD LOW NOISE HIGH PSRR LINEAR VOLTAGE REGULATOR Typical Applications Features The HMC860LP3E is ideal for: Ultra Low Noise: 3nV/√Hz at 10 kHz, 7nV/√Hz at 1 kHz • Test Instrumentation High Power Supply Rejection Ratio (PSRR) 80 dB at 1 kHz, 60 dB at 1 MHz • Military Radios, Radar and ECM • Basestation Infrastructure Four Voltage Outputs: VR1 @ 3V / 80 mA VR2, VR3 @ 3V / 20 mA VR4 @ 4.5V / 120 mA • Ultra Low Noise Frequency Generation • Fractional-N Synthesizer Supply • Mixed-Signal Circuit Supply Adjustable Outputs: 2.5V to 5.2V Low Power-Down Current: <1 µA 16 Lead 3x3 mm SMT Package: 9mm² Functional Diagram General Description POWER CONDITIONING - SMT 9 The HMC860LP3E is a BiCMOS ultra low noise quad-output voltage regulator. It features a low noise band-gap reference externally decoupled for best in-close noise performance. High Power Supply Rejection Ratio (PSRR) in the 0.1 MHz to 10 MHz range provides excellent rejection of preceding switching regulator noise. The four voltage outputs are ideal for frequency generation subsystems including Hittite’s broad line of PLLs with Integrated VCOs. Each output voltage can be adjusted higher or lower than the default value by using one external resistor. Each output can be set to 5V by grounding the corresponding HV pin. The regulator can be powered down by the TTL-compatible Enable input. The HMC860LP3E is housed in a 3x3mm QFN SMT package. Electrical Specifications, TA = +25 °C Conditions Min Typ Max Default Output Voltage VR1, VR2, VR3 Parameter Vdd = 5.5V; Maximum load current 3 3.05 3.1 V Default Output Voltage VR4 Vdd = 5.5V; Maximum load current 4.4 4.5 4.6 V Output Voltage Tolerance Vdd = 5.5V; Maximum load current 2 % Input Voltage Range (Default) Default output voltage configuration 4.8 5.6 V E.g.: VR1 = VR2 = VR3 = VR4 = 3.05V; Vdd, min = 3.35V Max (VRx) + 0.3V 5.6 V Set by external resistors. Vdd = Max(VRx)+0.3V 2.5 5.2 V Input Voltage Range Output Voltage Range VR1 to VR4 9-1 Units For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 978-250-3343 tel • 978-250-3373 fax • Order On-line at www.hittite.com Application Support: [email protected] HMC860LP3E v01.0811 QUAD LOW NOISE HIGH PSRR LINEAR VOLTAGE REGULATOR Electrical Specifications (Continued) Conditions Reference Voltage VREF Min Vdd = 5.5V; REF cannot source/sink external current Typ Max Units 1.21 V Output Current VR1 [1] TA = -40°C to +85°C 80 mA Output Current VR2, VR3 [1] TA = -40°C to +85°C 20 mA TA = -40°C to +85°C 120 mA TA = -40°C to +85°C 240 mA Output Current VR4 [1] Total Output Current Output Noise Spectral Density 10 Hz 100 Hz 1 kHz 10 kHz 100 kHz Integrated Output Noise 100 Hz to 100 kHz 2200 157 7 3 3 Vdd = 5.5V; VRx = 3.05V; VR4 = 4.5V Measured on Application Schematic Maximum Load Current nV/√Hz Vdd = 5.5V; VRx = 3.05V 1.5 µVrms Load Regulation, VR1 Vdd = 5.5V 0.01 % / mA Load Regulation, VR2 & VR3 Vdd = 5.5V 0.02 % / mA Load Regulation, VR4 Vdd = 5.5V 0.02 % / mA PSRR 0 Hz (DC Line Regulation) 1 kHz 100 kHz 1 MHz 10 MHz 50 MHz Output Voltage Variation vs. Package Base Temperature 25°C to 85°C -40°C to 25°C Current Consumption (IGND) 36 80 65 60 35 45 Vdd = 5.5V; Maximum load current Vdd = 5.5V; Maximum load current 0.015 0.045 Ven = Vdd = 5.5V; Maximum Load Current 1.9 Power Down Current Vdd = 5.5V; EN = Low; VRx outputs are floating (high - impedance) in Power-Down mode Start-Up Transient Time 0 to 90% of final voltage; Cref=1 µF; Cload=10 µF; Vdd = 5.5V 25 0 to 90% of final output voltage Cref = 1 µF; Cload = 10 µF; Vdd = 5.5V EN transition from 0 to Vdd 25 EN Turn-On Delay Enable Input EN High Level Enable Input EN Low Level dB % / °C % / °C 2.3 mA 1 µA ms ms 2 Vdd + 0.3 V 0 0.8 V Output Load Capacitance To guarantee stability, noise and PSRR performance 10 Output Capacitor ESR Required if no series resistor is used at the output. See “Stability” section. 0.2 2 Ohm Required if ESR is insufficient for one or more output capacitors. See “Stability” section. 0.1 1 Ohm Output series resistance µF [1] The regulator does not include short-circuit or over-temperature protection circuitry. The outputs will withstand short-circuit conditions for a duration of less than 10s. For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 978-250-3343 tel • 978-250-3373 fax • Order On-line at www.hittite.com Application Support: [email protected] 9 POWER CONDITIONING - SMT Parameter 9-2 HMC860LP3E v01.0811 QUAD LOW NOISE HIGH PSRR LINEAR VOLTAGE REGULATOR VR1 Noise Spectral Density, Vdd = 5.5V 10 -6 10 VR1=3.0V I(VR1)=75mA C=10μF Rs1=0.1Ohm -7 10 VR1 INSTRUMENT NOISE FLOOR 10 -8 10 -9 10 NOISE (V/rtHz) NOISE (V/rtHz) 10 VR2, VR3 Noise Spectral Density, Vdd = 5.5V -10 10 2 10 3 10 4 10 5 10 6 10 VR2=VR3=3.0V I(VR2 or VR3)=15mA C=10μF -7 VR2, VR3 INSTRUMENT NOISE FLOOR 10 -8 10 -9 10 7 -6 -10 10 2 10 3 10 FREQUENCY (Hz) VR4 Noise Spectral Density, Vdd = 5.5V NOISE (V/rtHz) 10 VR4=4.5V I(VR4)=100mA C=10μF Rs4=0.1Ohm -7 10 -8 10 -9 -10 10 2 10 3 10 4 10 5 10 10 6 10 7 6 10 7 10 8 -30 -40 -50 VR1: 3.0V/75mA VR4: 4.5V/100mA Rs1=0.1Ohm; C Rs4=0.1Ohm; C -70 VR1 VR4 -80 -90 2 10 10 3 10 4 10 5 10 6 10 7 VR1 Voltage vs. Supply, I(VR1) = 75 mA 3.10 -30 VR2: 3.0V/15mA VR3: 3.0V/15mA OUTPUT VOLTAGE (V) 3.08 -50 C =10.11μF LOAD -60 -70 -80 3.06 3.04 +25 C +90 C -40 C 3.02 VR2 VR3 -90 -100 2 10 =10.11μF LOAD FREQUENCY (Hz) VR2, VR3 Power Supply Rejection Ratio (PSRR), Vdd = 5.5V -40 =10.11μF LOAD -60 FREQUENCY (Hz) 10 3 10 4 10 5 10 FREQUENCY (Hz) 9-3 5 -6 VR4 INSTRUMENT NOISE FLOOR 10 POWER SUPPLY REJECTION RATIO (dB) POWER CONDITIONING - SMT 9 10 VR1, VR4 Power Supply Rejection Ratio (PSRR), Vdd = 5.5V POWER SUPPLY REJECTION RATIO (dB) 10 4 FREQUENCY (Hz) 6 10 7 10 8 3.00 4.8 5 5.2 5.4 5.6 5.8 6 SUPPLY VOLTAGE (V) For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 978-250-3343 tel • 978-250-3373 fax • Order On-line at www.hittite.com Application Support: [email protected] HMC860LP3E v01.0811 QUAD LOW NOISE HIGH PSRR LINEAR VOLTAGE REGULATOR VR4 Voltage vs. Supply, I(VR4) = 100 mA VR1 Voltage vs. Supply, T = 25 °C 4.6 3.08 OUTPUT VOLTAGE (V) 3.06 I(VR1) = 77mA I(VR1) = 13mA 3.04 3.02 3.00 4.8 5 5.2 5.4 5.6 5.8 4.55 4.5 4.45 4.4 6 +25 C +90 C -40 C 4.8 5 5.2 5.8 6 4.60 3.1 OUTPUT VOLTAGE (V) 3.08 OUTPUT VOLTAGE (V) 5.6 VR4 Voltage vs. Temperature, I(VR4) = 100 mA VR1 Voltage vs. Temperature, I(VR1) = 75 mA 3.06 3.04 Vdd = 5.0V Vdd = 5.5V Vdd = 6.0V 3.02 3.00 -40 5.4 SUPPLY VOLTAGE (V) SUPPLY VOLTAGE (V) -20 0 20 40 60 80 4.50 Vdd = 5.0V Vdd = 5.5V Vdd = 6.0V 4.45 4.40 -40 100 9 4.55 -20 0 20 40 60 80 100 TEMPERATURE (C) TEMPERATURE (C) Supply Turn-Off Transient, T = 90 °C Supply Turn-On Transient, T = 90 °C 5 5 VR4 4 OUTPUT VOLTAGE (V) OUTPUT VOLTAGE (V) VR4 VR3 3 VR1 2 1 0 4 VR3 3 VR1 2 1 0 0 10 20 30 TIME (ms) 40 50 0 10 20 30 40 POWER CONDITIONING - SMT OUTPUT VOLTAGE (V) 3.10 50 TIME (ms) For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 978-250-3343 tel • 978-250-3373 fax • Order On-line at www.hittite.com Application Support: [email protected] 9-4 HMC860LP3E v01.0811 QUAD LOW NOISE HIGH PSRR LINEAR VOLTAGE REGULATOR Absolute Maximum Ratings Vdd to GND Voltage +6.5V / -0.3V EN to GND Voltage Vdd + 0.5V / -0.3V RDx / HVx to GND Voltage Vdd + 0.5V / -0.3V Thermal Resistance (Junction to ground paddle) 30 °C/W Maximum Junction Temperature +125 °C Storage Temperature -65 to +150 °C Operating Temperature -40 to +85 °C ESD Sensitivity (HBM) Class 1C Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. The absolute maximum ratings apply individually only and not in combination. ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS Outline Drawing POWER CONDITIONING - SMT 9 NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS]. 3. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.15mm PER SIDE. 4. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.25mm PER SIDE. 5. ALL GROUND LEADS MUST BE SOLDERED TO PCB GROUND. 6. CLASSIFIED AS MOISTURE SENSITIVITY LEVEL (MSL) 1. Package Information Part Number Package Body Material Lead Finish HMC860LP3E RoHS-compliant Low Stress Injection Molded Plastic 100% matte Sn MSL Rating MSL1 [2] Package Marking [1] H860 XXX X [1] 4-Digit lot number XXXX [2] Max peak reflow temperature of 260 °C 9-5 For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 978-250-3343 tel • 978-250-3373 fax • Order On-line at www.hittite.com Application Support: [email protected] HMC860LP3E v01.0811 QUAD LOW NOISE HIGH PSRR LINEAR VOLTAGE REGULATOR Pin Descriptions Pin Number Function Description 1 Vdd Unregulated power supply input 2 GND Supply Ground 3 EN Enable Input, TTL Logic Level. The VRx outputs are floating (high impedance) when EN = Low. 4 REF Reference voltage (bandgap) output. Cannot be used to source/sink current to/from external circuits Interface Schematic 5 HV3 Sets VR3 to 5V output when connected to ground, otherwise no connection. 8 HV4 Sets VR4 to 5V output when connected to ground, otherwise no connection. 13 HV2 Sets VR2 to 5V output when connected to ground, otherwise no connection. 16 HV1 Sets VR1 to 5V output when connected to ground, otherwise no connection. 6 RD3 Resistive feedback for VR3, see “Output Voltage Adjust” section. 7 RD4 Resistive feedback for VR4, see “Output Voltage Adjust” section. 14 RD2 Resistive feedback for VR2, see “Output Voltage Adjust” section. 15 RD1 Resistive feedback for VR1, see “Output Voltage Adjust” section. 9 VR4 Regulator #4 Output 10 VR3 Regulator #3 Output 11 VR2 Regulator #2 Output 12 VR1 Regulator #1 Output Package Base N/C Should contact PCB metallic area for best thermal dissipation. Can be connected to Ground. For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 978-250-3343 tel • 978-250-3373 fax • Order On-line at www.hittite.com Application Support: [email protected] POWER CONDITIONING - SMT 9 9-6 HMC860LP3E v01.0811 QUAD LOW NOISE HIGH PSRR LINEAR VOLTAGE REGULATOR Application Schematic POWER CONDITIONING - SMT 9 The specified noise performance requires the 1µF decoupling capacitor between pins REF and GND (C1) and the 100nF capacitors connected between output VRx (x=1,2,3,4) and the respective RDx pin (C2, C3, C4 and C5). If noise performance is not critical for a particular output, the 100nF capacitor can be omitted for the respective regulator. In this case, noise spectral density will typically increase by a factor of 20X at 10kHz. The 1µF REF capacitor causes a 25ms typical turn-on start-up time. Stability Two approaches are recommended to manage the stability of the high-current regulators VR1 and VR4. If only one decoupling capacitor is used at the output, the capacitor series resistance Resr must be between 0.2 Ohm and 2 Ohm to insure stability across all loading conditions. This is shown at output VR4 in the application schematic. Note that ceramic capacitors typically have much lower Resr (as low as 0.02 Ohm at resonance) hence they will need a series resistor to insure stability. In the case when several capacitors are connected at the output (which is often the case with noise and spurious sensitive circuits), an alternate approach is to insert a small resistor in series with the load but after the 100nF feedback capacitor. This is shown by Rs1 at the VR1 output in the application schematic. The minimum resistor value is 0.1 Ohm, while the maximum value is set by the acceptable output voltage drop. Due to the lower current, regulators VR2 and VR3 do not have special stability requirements. Typical 10µF ceramic capacitor ESR of 0.02 Ohm is sufficient for their stability. 9-7 For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 978-250-3343 tel • 978-250-3373 fax • Order On-line at www.hittite.com Application Support: [email protected] HMC860LP3E v01.0811 QUAD LOW NOISE HIGH PSRR LINEAR VOLTAGE REGULATOR Output Voltage Adjust There are several ways to adjust the output voltage for each regulator. A 5V setting for any output can be achieved by grounding the respective HVx (x=1,2,3,4) pin. Any other value requires an external resistor, connected between RDx and GND for a voltage higher than the default, or between VRx and RDx for a voltage lower than the default. The figures below show the values of the internal resistive dividers that set the default output voltage a. for 3V and b. for 4.5V and two examples of two different voltage settings: c. shows a default 3V output changed to 3.3V by connecting a 220k Ohm resistor between RDx and GND, while d. shows the same output adjusted to 2.5V by connecting a 120k Ohm resistor between VRx and RDx. The internal resistors have a temperature coefficient (TempCo) of +270ppm/°C. When the default output voltage is modified by using an external resistor with a different TempCo, the temperature behavior of the respective output will differ from this specification, although the difference will likely be very small. R1× (R2 + RX ) VRX ≈ VREF × 1 + (R2 × RX ) For VRx > VRx_default; X = 1, 2, 3, 4 VREF=1.21 Resistor values in KΩ VRx_default = 3V for VR1, VR2 & VR3 VRx_default = 4.5V for VR4 R1× RX VRX ≈ VREF × 1 + R2 × (R1 + RX ) For VRx < VRx_default; X = 1, 2, 3, 4 VREF=1.21 Resistor values in KΩ For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 978-250-3343 tel • 978-250-3373 fax • Order On-line at www.hittite.com Application Support: [email protected] POWER CONDITIONING - SMT 9 9-8 HMC860LP3E v01.0811 QUAD LOW NOISE HIGH PSRR LINEAR VOLTAGE REGULATOR 9-9 Evaluation Schematic POWER CONDITIONING - SMT 9 For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 978-250-3343 tel • 978-250-3373 fax • Order On-line at www.hittite.com Application Support: [email protected] HMC860LP3E v01.0811 QUAD LOW NOISE HIGH PSRR LINEAR VOLTAGE REGULATOR Evaluation PCB List of Materials for Evaluation PCB 124352 [1] Item Description Item Description J7 - J20 2 Pos Vertical TIN PCB [2] 124072 Evaluation PCB C7 4.7 µF Capacitor, 0805 Pkg. C10, C11, C13, C14, C19, C21, C23, C25 100 nF Capacitor, 0402 Pkg. C12 1.0 µF Capacitor, 0603 Pkg. C15 - C18 10 µF Capacitor, 0805 Pkg. C20, C22, C24, C26 1000 pF Capacitor, 0402 Pkg. R13, R16, R18, R21, R29 1 Ohm Resistor, 0402 Pkg. R23, R25 0.2 Ohm Resistor, 0402 Pkg. R24, R26 - R28 0 Ohm Resistor, 0402 Pkg. TP1 - TP3 Test Point PC Compact U1 HMC860LP3E Quad Regulator [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350 or FR4 A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. For price, delivery and to place orders: Hittite Microwave Corporation, 2 Elizabeth Drive, Chelmsford, MA 01824 978-250-3343 tel • 978-250-3373 fax • Order On-line at www.hittite.com Application Support: [email protected] POWER CONDITIONING - SMT 9 9 - 10