ICHAUS IC-HKBMSOP8

iC-HK, iC-HKB
155 MHz LASER SWITCH
Rev F1, Page 1/8
FEATURES
APPLICATIONS
♦
♦
♦
♦
♦
♦
♦
♦
♦ Data transmission
♦ Laser scanning devices
♦ Optical storage devices
♦
♦
♦
♦
♦
Laser switch for frequencies from CW up to 155 MHz
Spike-free switching of the laser current
Dual switching inputs with independent current control
Operates as a voltage-controlled current source
Pulsed operation with up to 700 mA per channel
CW operation with up to 150 mA per channel
Simple power control at pin CI
Control to the mean of the laser power in conjunction with
iC-WK/L (CW laser diode driver)
Supplement to iC-WK/L for pulsed operation
Thermal shutdown
Protective ESD circuitry
iC-HKB for driving blue laser diodes
Option: extended temperature range
PACKAGES
SO8
thermal pad
MSOP8
thermal pad
BLOCK DIAGRAM
LDA
MDK
MDA
iC−WK
CI
Suitable laser diode configurations:
7
Operation with constant
current (uncontrolled):
CLDA
4
P
5
M/N
MD LD
LD
RM
iC−HK/B
2
8
LDK
Operation in conjunction with
iC−WK (power controlled):
VDD
N
CI
M1
M2
MD LD
CI
EN1
EN2
1
M
5
LD
MD
OVERTEMP.
SHUTDOWN
AGND1
2
RK1
Copyright © 2009 iC-Haus
7
3
AGND2
4
GND
6
P
MD LD
RK2
http://www.ichaus.com
iC-HK, iC-HKB
155 MHz LASER SWITCH
Rev F1, Page 2/8
DESCRIPTION
Laser Switch iC-HK/B enables the spike-free switching of laser diodes with well-defined current pulses at
frequencies ranging from DC to 155 MHz.
of the emitted laser power is constant (APC), providing there is a constant duty cycle and a switching
frequency higher than 100 kHz.
+3.5..5 V
The diode current is determined by the voltage at
pin CI and by the resistors RK1 and RK2. The two
fast switches are controlled independently via CMOS
inputs EN1 and EN2. The laser diode can thus be
turned on and off or switched between different current levels defined by the ratio of RK1 and RK2.
CLDA
LD
VDD
CI
M1
M2
EN1
1
EN2
5
V(CI)
The integrated thermal shutdown feature prevents
damage from excessive temperature.
OVERTEMP.−
SHUTDOWN
AGND1
AGND2 GND
2
4
RK1
iC-HK/B supplements the laser diode driver iC-WK
which uses the monitor current of the laser diode to
control the laser power. iC-WK therefore controls the
voltage at pin CI in such a way that the mean value
VCC
LDK
iC−HK/B
8
Each channel can be operated on 150 mA DC and
up to 700 mA pulsed current depending on the frequency, duty cycle and heat dissipation.
6
7
3
6
RK2
Figure 1: Operation as a voltage-controlled current source
LDA
+3.5..5 V
CVCC
CLDA
100 nF
1 uF
TRANSIENT
CVDD
2.2 nF
100 nF
LED
PROTECTION
MD
MDK
LD
MDA
−
7
3
+
iC−HK/B
VREF
0.5 V
1
CLD
8
CI
LDK
VDD
CI
M2
M1
D
LDK
iC−WK
NQ
R
CM
CI
RM
OVER CURRENT
1
RGND
0V
GND
200 Ω..50 kΩ
FEEDBACK MON./
EN1
1
EN1
EN2
5
EN2
47 nF..
OVERTEMP.
AGND
OVERTEMP.−
SHUTDOWN
AGND1
AGND2
2
4
GND
DGND
RK1
0..
6
RK2
0..
Figure 2: Operation of iC-HK/B in conjunction with CW driver iC-WK (see application information on
optional parts/connections)
iC-HK, iC-HKB
155 MHz LASER SWITCH
Rev F1, Page 3/8
PACKAGES SO8tp, MSOP8tp to JEDEC
PIN CONFIGURATION SO8tp
PIN FUNCTIONS
No. Name Function
1
8
CI
EN1
2
7
VDD
AGND1
LDK
4
AGND2
HK
Code...
...yymm
3
6
GND
5
EN2
1
LDK
AGND2
iC−HK
Code
AGND1
EN1
AGND1
LDK
AGND2
EN2
GND
VDD
CI
Channel 1 Switching Input
Channel 1 Reference Ground
Driver Output (LD Cathode)
Channel 2 Reference Ground
Channel 2 Switching Input
Ground
+5 V Supply Voltage
Voltage Reference for Current Control
The Thermal Pad is to be connected to a Ground Plane
on the PCB.
PIN CONFIGURATION MSOP8tp
EN1
1
2
3
4
5
6
7
8
CI
VDD
GND
EN2
iC-HK, iC-HKB
155 MHz LASER SWITCH
Rev F1, Page 4/8
ABSOLUTE MAXIMUM RATINGS
Beyond these values damage may occur; device operation is not guaranteed.
Item
No.
Symbol
Parameter
Conditions
Unit
Min.
Max.
G001 VDD
Voltage at VDD
-0.7
6
V
G002 I(VDD)
Current in VDD
-10
150
mA
G003 V(CI)
Voltage at CI
-0.7
6
V
G004 I(LDK)
Current in LDK
DC current
-10
300
mA
G005 I(AGND1)
Current in AGND1
DC current
-150
10
mA
G006 I(AGND2)
Current in AGND2
DC current
-150
10
mA
G007 V()
Voltage at EN1, EN2, AGND1 and
AGND2
-0.7
6
V
G008 V(LDK)
Voltage at LDK
iC-HK
iC-HKB
-0.7
-0.7
6
15
V
V
G009 Vd()
Susceptibility to ESD at all pins
HBM, 100 pF discharged through 1.5 kΩ
1
kV
G010 Tj
Operating Junction Temperature
-40
150
°C
G011 Ts
Storage Temperature Range
-40
150
°C
THERMAL DATA
Operating Conditions: VDD = 3.5...5.5 V
Item
No.
Symbol
Parameter
Conditions
T01
Ta
Operating Ambient Temperature Range
(extended range on request)
T02
Rthja
Thermal Resistance Chip/Ambient
(SO8)
soldered to PCB, no additional cooling areas
therm. pad soldered to approx. 2 cm² cooling
area
Thermal Resistance Chip/Ambient
(MSOP8)
soldered to PCB, therm. pad soldered to
approx. 2 cm² cooling area
T03
Unit
Min.
Rthja
Typ.
-25
All voltages are referenced to ground unless otherwise stated.
All currents into the device pins are positive; all currents out of the device pins are negative.
Max.
85
°C
30
170
50
K/W
K/W
30
60
K/W
iC-HK, iC-HKB
155 MHz LASER SWITCH
Rev F1, Page 5/8
ELECTRICAL CHARACTERISTICS
Operating Conditions: VDD = 3.5...5.5 V, Tj = -25...125 °C unless otherwise stated
Item
No.
Symbol
Parameter
Conditions
Tj
°C
Fig.
Unit
Min.
Typ.
Max.
Total Device
001
VDD
Permissible Supply Voltage
3.5
5.5
V
002
I(VDD)
Supply Current in VDD
CW operation
0
80
µA
003
I(VDD)
Supply Current in VDD
pulsed operation,
f(EN1, EN2) = 150 MHz
0
150
mA
004
V(LDK)
Permissible Voltage at LDK
iC-HK
iC-HKB
0
0
5.5
12
V
V
005
Vc(CI)hi
Clamp Voltage hi at CI
Vc(CI) = V(CI) – VDD,
I(CI) = 10 mA, other pins open
0.4
1.25
V
006
Vc(EN)hi
Clamp Voltage hi at EN1, EN2
Vc(EN) = V(EN) – VDD,
I(EN) = 1 mA, other pins open
0.4
1.25
V
007
Vc()lo
Clamp Voltage lo at VDD, LDK,
CI, EN1, EN2, AGND1, AGND2
I() = -10 mA, other pins open
-1.25
-0.4
V
008
Ipd()
Pull-Down Current at CI, EN1,
EN2
1
5
µA
009
Toff
Overtemperature Shutdown
110
150
°C
150
mA
Laser Control LDK, CI, EN1, EN2
101
Icw(LDK)
Permissible CW Current in LDK
(per channel)
102
Ipk(LDK)
Permissible Pulsed Current in
LDK (per channel)
f > 100 kHz, thi/T < 1:10
700
mA
107
Vs(LDK)
Saturation Voltage at LDK
I(LDK) = 40 mA
I(LDK) = 60 mA
I(LDK) = 150 mA, iC-HK
I(LDK) = 150 mA, iC-HKB
1.2
1.3
1.5
1.8
V
V
V
V
108
I0(LDK)
Leakage Current in LDK
ENx = lo, V(LDK) = VDD
10
µA
109
tr()
LDK Current Rise Time
Iop = 150 mA,
I(LDK): 10% → 90%Iop
3
1.5
ns
110
tf()
LDK Current Fall Time
Iop(LDK) = 150 mA,
I(LDK): 90% → 10%Iop
3
1.5
ns
111
tp()
Propagation Delay
V(ENx) → I(LDK)
ENx hi ↔ lo, V(50%) → I(50%)
3
ns
112
Vt(ENx)
Input Threshold Voltage
33
67
%VDD
113
V(CI)
Permissible Voltage at CI
0
5.5
V
114
Vt(CI)
Threshold Voltage at CI
I(LDK) < 5 mA
0.75
1.15
V
115
CR()
Current Matching Channel1/Channel2
V(CI) = 0...VDD,
I(LDK) = 30...300 mA, RK1 = RK2
0.9
0
1
50
1
1.1
iC-HK, iC-HKB
155 MHz LASER SWITCH
Rev F1, Page 6/8
ELECTRICAL CHARACTERISTICS DIAGRAMS
I(LDK)
300 mA
RKx= 0 Ω
250
I(LDK)
tr
RKx= 1 Ω
200
tf
RKx= 2 Ω
I op
150
RKx= 3 Ω
100
RKx= 4 Ω
RKx= 5 Ω
RKx= 6 Ω
90 % I op
RKx= 8 Ω
RKx= 10 Ω
RKx= 15
RKx= 20
RKx= 30
RKx= 50
50
0
10 % I op
1
1.2
1.4
1.6
1.8
2
2.2
2.4
2.6 V
V(CI)
t
Figure 3: Laser current pulse in LDK
Figure 4: Diode current vs. V(Cl) at Tj = 27 °C
I(LDK)
700 mA
Ω
Ω
Ω
Ω
RKx = 0Ω
I(LDK)
1200 mA
RKx = 0Ω
600
1000
500
RKx = 1Ω
800
400
RKx = 1Ω
RKx = 2Ω
300
RKx = 3Ω
200
RKx = 4Ω
RKx = 5Ω
RKx = 6Ω
RKx = 8Ω
RKx = 10 Ω
100
0
2.2
RKx = 15 Ω
RKx = 20 Ω
RKx = 30 Ω
RKx = 50 Ω
2.4
2.6
2.8
3
3.2
3.4
3.6
600
RKx = 3Ω
400
RKx = 4Ω
RKx = 5Ω
RKx = 6Ω
RKx = 8Ω
RKx = 10 Ω
RKx = 15 Ω
RKx = 20 Ω
RKx = 30 Ω
RKx = 50 Ω
200
0
3.5
3.8V
V(CI)
Figure 5: Diode current vs. V(Cl) at Tj = 27 °C
RKx = 2Ω
4
5V
4.5
V(CI)
Figure 6: Diode current vs. V(Cl) at Tj = 27 °C
I(LDK)
1.5 A
I(LDK)
250 mA
200
1
RKx = 0Ω
RKx = 0Ω
max
max
150
min
0.5
100
min
50
0
0
0
0.5
1
1.5
2
0
V(CI)
Figure 7: Diode current variation vs. V(CI) at
V(LDK) = 3 V
1
2
3
4
5V
V(CI)
Figure 8: Diode current variation vs. V(CI) at
V(LDK) = 3 V
iC-HK, iC-HKB
155 MHz LASER SWITCH
Rev F1, Page 7/8
DESCRIPTION OF FUNCTIONS
Laser current dependency of V(Cl), RK1, RK2
Depending on the laser diode different diode currents
are necessary to obtain the required laser power. The
values for V(CI), RK1 and RK2 can be determined for
the required diode current at room temperature from
the opposite diagram. A parallel to the x axis must be
drawn through the desired diode current. Either RKx
can be obtained for a required value of V(CI) or the
respective value of V(VI) can be achieved for a given
RKx.
I(LDK)
300 mA
RKx= 0 Ω
2
250
RKx= 1 Ω
200
RKx= 2 Ω
150
RKx= 3 Ω
100
RKx= 4 Ω
RKx= 5 Ω
RKx= 6 Ω
1
RKx= 8 Ω
RKx= 10 Ω
RKx= 15
RKx= 20
RKx= 30
RKx= 50
50
0
1
1.2
1.4
1.6 3
1.8
1.75
Thermal Shutdown
iC-HK/B is protected by an integrated thermal shutdown feature. When the shutdown temperature is
reached both channels are locked.
2
2.2
2.4
Ω
Ω
Ω
Ω
2.6 V
V(CI)
Figure 9: Diode current vs. V(Cl) at Tj = 27 °C
APPLICATION NOTES
Application notes for iC-HK are available as a separate document.
iC-Haus expressly reserves the right to change its products and/or specifications. An Infoletter gives details as to any amendments and additions made to the
relevant current specifications on our internet website www.ichaus.de/infoletter; this letter is generated automatically and shall be sent to registered users by
email.
Copying – even as an excerpt – is only permitted with iC-Haus approval in writing and precise reference to source.
iC-Haus does not warrant the accuracy, completeness or timeliness of the specification on this site and does not assume liability for any errors or omissions
in the materials. The data specified is intended solely for the purpose of product description. No representations or warranties, either express or implied, of
merchantability, fitness for a particular purpose or of any other nature are made hereunder with respect to information/specification or the products to which
information refers and no guarantee with respect to compliance to the intended use is given. In particular, this also applies to the stated possible applications or
areas of applications of the product.
iC-Haus conveys no patent, copyright, mask work right or other trade mark right to this product. iC-Haus assumes no liability for any patent and/or other trade
mark rights of a third party resulting from processing or handling of the product and/or any other use of the product.
As a general rule our developments, IPs, principle circuitry and range of Integrated Circuits are suitable and specifically designed for appropriate use in technical
applications, such as in devices, systems and any kind of technical equipment, in so far as they do not infringe existing patent rights. In principle the range of
use is limitless in a technical sense and refers to the products listed in the inventory of goods compiled for the 2008 and following export trade statistics issued
annually by the Bureau of Statistics in Wiesbaden, for example, or to any product in the product catalogue published for the 2007 and following exhibitions in
Hanover (Hannover-Messe).
We understand suitable application of our published designs to be state-of-the-art technology which can no longer be classed as inventive under the stipulations
of patent law. Our explicit application notes are to be treated only as mere examples of the many possible and extremely advantageous uses our products can
be put to.
iC-HK, iC-HKB
155 MHz LASER SWITCH
Rev F1, Page 8/8
ORDERING INFORMATION
Type
Package
Order Designation
iC-HK
SO8tp
MSOP8tp
iC-HK SO8
iC-HK MSOP8
iC-HKB
SO8tp
MSOP8tp
iC-HKB SO8
iC-HKB MSOP8
For technical support, information about prices and terms of delivery please contact:
iC-Haus GmbH
Am Kuemmerling 18
D-55294 Bodenheim
GERMANY
Tel.: +49 (61 35) 92 92-0
Fax: +49 (61 35) 92 92-192
Web: http://www.ichaus.com
E-Mail: [email protected]
Appointed local distributors: http://www.ichaus.de/support_distributors.php