SPECIFICATION FOR LCD MODULE Model No. TM122ADA6 Prepared by: Date: Checked by : Date: Verified by : Date: Approved by: Date: TIANMA MICROELECTRONICS CO., LTD REVISION RECORD Date Ref. Page Revision No. 1/22 Revision Items Check & Approval 1 General Specifications: 1.1 Display type: STN 1.2 Display color*: Display color: Blue-Black Background: Grey 1.3 Polarizer mode: Reflective/Positive 1.4 Viewing Angle: 6:00 1.5 Driving Method: 1/16 Duty 1/5 Bias 1.6 Backlight: none 1.7 Controller: S6A0069X01-C0CX(KS0066UP-00CC) 1.8 Display Fonts: 5 x 7 dots+Cursor(1 Character) 1.9 Data Transfer: 8 Bit Parallel 1.10 Operating Temperature: 0----+50 Storage Temperature: -20----+60 1.11 Outline Dimensions: Refer to outline drawing on next page 1.12 Dot Matrix: 12 Characters X 2 Lines 1.13 Dot Size: 0.45X0.60(mm) 1.14 Dot Pitch: 0.55X0.70 (mm) 1.15 Weight: Approx. 30g * Color tone is slightly changed by temperature and driving voltage. 2/22 3 LCD Module Part Numbering System T M 122 A DA 6 MODIFICATION CODE DESIGNATOR BACKLIGHT TYPE A: REFLECTIVE, NO BACKLIGHT LCD TYPE D: GREY MODE STN POSITIVE MODULE SERIES MODULE TYPE 3 DIGITS INDICATING 12 CHARACTERS X 2 LINES T: TIANMA M: MODULE 4/22 4 Circuit Block Diagram 5/22 5 Absolute Maximum Ratings Item Symbol Min. Max. Power Supply Voltage VDD VSS -0.3 7.0 Unit Remark V LCD Driving Voltage VLCD Operating Temperature Range TOP Storage Temperature Range -0.3 0 -20 TST 6/22 13.0 +50 +60 No Condensation 6 Electrical Specifications and Instruction Code 6.1 Electrical characteristics Item Symbol Min. Typ. Max. Unit Supply Voltage (Logic) VDD VSS 4.5 5.0 5.5 V Supply Voltage (LCD Drive) VLCD - 4.5 - V 0.7VDD - VDD+0.3 V -0.3 - 0.2 VDD V Input Signal Voltage High VIH VDD=5.0 Low VIL VDD=5.0 Supply current (Logic) IDD - - 1.2 mA Supply current (LCD Drive) IEE - - 0.4 mA 7/22 6.2 Interface Signals Pin No. Symbol Level Description 1 Vss/K 0V 2 Vdd 5.0V Power supply voltage for logic and LCD(+) 3 V0 0.5V Power supply voltage for LCD(-) 4 RS H/L H:Select data register L: Select instruction register 5 R/W H/L Selects read or write Ground and Power supply voltage for LED(-) H: Read operation L: Write operation 6 E H/L Starts data read/write 7 DB0 H/L Data bit 0 8 DB1 H/L Data bit 1 9 DB2 H/L Data bit 2 10 DB3 H/L Data bit 3 11 DB4 H/L Data bit 4 12 DB5 H/L Data bit 5 13 DB6 H/L Data bit 6 14 DB7 H/L Data bit 7 15 NC - No Signal 8/22 )>"!0- (00-6&A%+&B++&CA*B58+ 0RGH &KDUDFWHULVWLF 6\PERO 0LQ 7\S 0D[ WF W5W) WZ 5:DQG566HWXS7LPH WVX 5:DQG56+ROG7LPH W+ 'DWD6HWXS7LPH WVX 'DWD+ROG7LPH W+ (&\FOH7LPH WF W5W) (3XOVH:LGWK+LJK/RZ WZ 5:DQG566HWXS7LPH WVX 5:DQG56+ROG7LPH W+ 'DWD2XWSXW'HOD\7LPH W' 'DWD+ROG7LPH W'+ (&\FOH7LPH (5LVH)DOO7LPH (3XOVH:LGWK+LJK/RZ :ULWH0RGH 5HIHUWR)LJ (5LVH)DOO7LPH 5HDG0RGH 5HIHUWR)LJ 7 8QLW QV QV 56 5: 9 , + 9 , / W68 W K 9 , / 9 , / W K WZ 9 , + 9 , / ( WI 9 , + 9 , / 9 , / W 68 WU 9 , + 9 , / '%a'% W K 9 , + 9 , / 9DOLG 'DWD W& )LJXUH:ULWH0RGH7LPLQJ'LDJUDP 56 9 , + 9 , / WK W 68 5: 9 , + 9 , + WK WZ WI ( WU '%a'% 9 , + 9 , / 9 , + 9 , / W' 9 , + 9 , / 9DOLG 'DWD 9 , / W' + 9 , + 9 , / W& )LJXUH5HDG0RGH7LPLQJ'LDJUDP )%>0 ,QVWUXFWLRQ&RGH ,QVWUXFWLRQ ([HFXWLRQ WLPHIRVF N+] 'HVFULSWLRQ 56 5: '% '% '% '% '% '% '% '% &OHDU 'LVSOD\ 5HWXUQ +RPH :ULWH¦+§WR''5$0DQGVHW ''5$0DGGUHVVWR¦+§IURP$& 6HW''5$0DGGUHVVWR¦+§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uGRWVuGRWV $& $& $& $& $& $& 6HW&*5$0DGGUHVVLQDGGUHVV FRXQWHU $& $& $& $& $& $& $& 6HW''5$0DGGUHVVLQDGGUHVV FRXQWHU PV PV PV PV :KHWKHUGXULQJLQWHUQDORSHUDWLRQ RUQRWFDQEHNQRZQE\UHDGLQJ%) %) $& $& $& $& $& $& $& 7KHFRQWHQWVRIDGGUHVVFRXQWHU FDQDOVREHUHDG :ULWH'DWDWR 5$0 ' ' ' ' ' ' ' ' :ULWHGDWDLQWRLQWHUQDO5$0 ''5$0&*5$0 PV ' ' ' ' ' ' ' ' 5HDGGDWDIURPLQWHUQDO5$0 ''5$0&*5$0 PV 5HDG%XV\ )ODJDQG $GGUHVV 5HDG'DWD IURP5$0 PV ¦¦GRQ©WFDUH )+0-;:,6D**))?**7 )+0-;:,6D**))?**7 7 Optical Characteristics 7.1 Optical Characteristics Item Symbol Ta=25 Condition y =0 x Viewing Angle Response Time Turn on Turn off -35 Typ. -- Max. Cr Unit 20 Cr≥2 Deg x =0 y Contrast Ratio Min. x =0 y =0 Ton -30 -- 30 4.0 - - - - 250 x =0 ms y =0 - Toff 13/22 - 250 7.2 Definition of Optical Characteristics 7.2.1 Definition of Viewing Angle Top Top Bottom 7.2.2 Definition of Contrast Ratio Bottom Contrast Ratio = B2/B1 = Measuring Conditions: 1) Ambient Temperature: 25 7.2.3 Definition of Response time Turn on time: t o n = t d + t r Measuring Condition: 1) Operating Voltage: 4.5V unselected state brightness selected state brightness ; 2) Frame frequency: Turn off time: t o ff = t d + t f 2) Frame frequency: 84.3Hz 14/22 84.3Hz 8 Reliability 8.1 Content of Reliability Test No. Test Item 1 High Temperature Storage Low Temperature 2 Storage Content of Test Endurance test applying the high storage temperature for a long time Endurance test applying the low storage temperature for a long time Endurance test applying the electric current) and the stress (voltage thermal stress to the element for a long time Endurance test applying the electric stress under low temperature for a long time Endurance test applying the high temperature and high humidity storage for a long time Endurance test applying the low and high temperature cycle 25 80 25 -30 30min 5min 30min 5min ──────────── 1 cycle 3 High Temperature Operation 4 Low Temperature Operation 5 High Temperature /Humidity Storage 6 Temperature Cycle 7 Vibration Test (package state) Endurance test applying the vibration during transportation 8 Shock Test (package state) Endurance test applying the shock during transportation 9 Atmospheric Pressure Test Endurance test applying the atmospheric pressure during transportation by air 15/22 Ta=25 Test condition 60 240H -20 240H 50 240H 0 240H 60 95%RH 240H -30 /80 10 cycles 10Hz~500Hz, 100m/s2, 120min Half- sine wave, 300m/s2, 18ms 25kPa 16H 8.2 Failure Judgment Criterion Criterion Item Test Item No. 1 2 3 4 5 6 7 8 9 Failure Judgement Criterion Basic Specification √ √ √ √ √ √ √ √ √ Out of the basic Specification Electrical specification √ √ √ √ √ Mechanical Specification Optical Characteristic Note Remark Out of the electrical specification √ √ √ √ √ √ √ √ Out of the mechanical specification √ Out of the optical specification For test item refer to 8.1 Basic specification = Optical specification + Mechanical specification 16/22 9 QUALITY LEVEL Examination or Test At Ta=25 (unless otherwise stated) Inspection Min. Max. Unit IL AQL Under normal Major External illumi-nation and 1.0 Visual eyesight condition, the See Appendix A II Minor Inspection dis-tance between eyes 2.5 and LCD is 25cm. Under normal Major Display illumi-nation and 1.0 See Appendix B II Defects eyesight condition, Minor display on inspection. 2.5 Note: Major defects: Open segment or common, Short, Serious damages, Leakage Miner defects: Others Sampling standard conforms to GB2828 17/22 10 Precautions for Use of LCD Modules 10.1 Handling Precautions 10.1.1 The display panel is made of glass. Do not subject it to a mechanical shock by dropping it from a high place, etc. 10.1.2 If the display panel is damaged and the liquid crystal substance inside it leaks out, be sure not to get any in your mouth, if the substance comes into contact with your skin or clothes, promptly wash it off using soap and water. 10.1.3 Do not apply excessive force to the display surface or the adjoining areas since this may cause the color tone to vary. 10.1.4 The polarizer covering the display surface of the LCD module is soft and easily scratched. Handle this polarizer carefully. 10.1.5 If the display surface is contaminated, breathe on the surface and gently wipe it with a soft dry cloth. If still not completely clear, moisten cloth with one of the following solvents: Isopropyl alcohol Ethyl alcohol Solvents other than those mentioned above may damage the polarizer. Especially, do not use the following: Water Ketone Aromatic solvents 10.1.6 Do not attempt to disassemble the LCD Module. 10.1.7 If the logic circuit power is off, do not apply the input signals. 10.1.8 To prevent destruction of the elements by static electricity, be careful to maintain an optimum work environment. a. Be sure to ground the body when handling the LCD Modules. b. Tools required for assembly, such as soldering irons, must be properly ground. c. To reduce the amount of static electricity generated, do not conduct assembly and other work under dry conditions. d. The LCD Module is coated with a film to protect the display surface. Be care when peeling off this protective film since static electricity may be generated. 18/22 10.2 Storage precautions 10.2.1 When storing the LCD modules, avoid exposure to direct sunlight or to the light of fluorescent lamps. 10.2.2 The LCD modules should be stored under the storage temperature range. If the LCD modules will be stored for a long time, the recommend condition is: Temperature : 0 40 Relatively humidity: 80% 10.2.3 The LCD modules should be stored in the room without acid, alkali and harmful gas. 10.3 The LCD modules should be no falling and violent shocking during transportation, and also should avoid excessive press, water, damp and sunshine. 19/22 Appendix A Inspection items and criteria for appearance defects Items Contents Criteria Leakage Not permitted Rainbow According to the limit specimen Polarizer Black spot (in viewing area) Wrong polarizer attachment Not permitted Bubble between polarizer and glass Not counted Scratches of polarizer According to the limit specimen φ<0.3mm Max. 3 defects allowed 0.3mm φ 0.5mm Not counted Max. 3 spots allowed X<0.2mm 0.2mm X 0.5mm X=(a+b)/2 Black line (in viewing area) Not counted Max. 3 lines allowed a<0.02mm 0.02mm a 0.05mm b 2.0mm Progressive cracks Not permitted 20/22 Max. 3 spots (lines) allowed Appendix B Inspection items and criteria for display defects Items Contents Critera Open segment or open common Not permitted Short Not permitted Wrong viewing angle Not permitted Contrast radio uneven According to the limit specimen Crosstalk According to the limit specimen Not counted X<0.1mm Max.3 dots allowed 0.1mm X 0.2mm X=(a+b)/2 Pin holes and cracks in segment (DOT) Black spot (in viewing area) Not counted Max.2 dots allowed A<0.1mm 0.1mm A 0.2mm D<0.25mm Not counted Max.3 spots allowed X<0.1mm 0.1mm X 0.2mm X=(a+b)/2 Black line (in viewing area) Not counted Max.3 lines allowed a<0.02mm 0.02mm a 0.05mm b 0.5mm 21/22 Max.3 dots allowed Max.3 spots (lines) allowed Appendix B Inspection items and criteria for display defects (continued) Items Content Critera Not counted Max. 2 defects allowed x 0.1mm 0.1mm x 0.2mm x=(a+b)/2 Not counted Transformation of segment a 0.1mm Max. 1 defects allowed 0.1mm a 0.2mm D>0 Max.2 defects allowed 0.8W a 1.2W a=measured value of width W=nominal value of width 22/22 Max.3 defects allowed