Chunghwa Picture Tubes, Ltd. Inspection Specification To : Ceramate 光碁 Date : 091124 CPT TFT-LCD Incoming Inspection Standards Model :CLAA070LC0ACW _Y ACCEPTED BY： APPROVED BY CHECKED BY PREPARED BY 張聖暉 李家銘 劉紀平 Prepared by : Product Planning Management Division Small & Medium Product TFT Business Unit CHUNGHWA PICTUER TUBES, LTD. 1127 Hopin Rd., Padeh, Taoyuan, Taiwan 334, R.O.C. TEL: +886-3-3675151 FAX: +886-3-377-3001 Doc.No Issue Date INCOMING INSPECTION STANDARDS IIS_CLAA070LC0ACW _Y_V1_Ceramate_091124 091124 CPT Disallow Disclosure, Reproduction or Distribution 1. Incoming inspection right (1) The Incoming Inspection Standard will be agreed and signed by both sides(Customer and CPT) before CPT receives the PO(Purchase Order) forward 7days. (2) The Customer shall notify CPT inspection result in writing within 14 day, otherwise goods will be deemed accepted by customer. 2. Inspection conditions is as follows: (1) Viewing distance is approximately 35 ~ 40 cm (2) Viewing angle is normal to the LCD panel as Fig _1(30°) (3) Ambient temperature is approximately 25 ± 5℃ (4) (5) (6) (7) Ambient humidity is 60 ± 5% RH Ambient illuminance is from 300 ~ 500 Lux. Input signal timing should be typical value. Mura & Light leakage inspection at ND-Filter 2% Fig _ 1 3. Special condition (1) Viewing distance is close for inspection of adjacent dots and distance between defect dots. (2) Viewing condition of “Shot block non-uniformity from oblique angle” is as Fig _2. (3) Exceptional case: View angle ± 40° while inspected image-sticking. Fig _ 2 CPT Confidential and Property 1/5 IIS_CLAA070LC0ACW _Y_V1_Ceramate_091124 CPT Disallow Disclosure, Reproduction or Distribution 4. Inspection Criteria DEFECT TYPE LIMIT 0.1mm＜W≦0.2mm SCRATCH L≦20mm SPOT FIBER INTERNAL POLARIZER BUBBLE Dent ELECTRICAL DEFECT N=0 0.4mm≦φ≦0.6mm N≦3 0.6mm＜φ N=0 L≦2.5mm N≦5 0.3mm＜W, 2.5mm＜L N=0 0.4mm≦φ≦0.6mm N≦4 0.6mm＜φ N=0 0.5mm≦φ≦0.6mm N≦6 0.6mm＜φ N=0 C Area BRIGHT DOT N≦3 20mm＜L, 0.1mm＜W 0.2mm≦W≦0.3mm, VISUAL DEFECT Note O Area Note1 Note1 Note1 Note1 Note1 Total N≦3 Note2 DARK DOT N≦3 Note3 TOTAL DOT N≦6 TWO ADJACENT DOT N≦2 THREE OR MORE ADJACENT DOT LINE DEFECT NOT ALLOWED NOT ALLOWED Note4 - (1) One pixel consists of 3 sub-pixels, including R, G, and B dot. (Sub-pixel = Dot) (2) Panel is acceptable if distance between 2 dot defects are greater or equal to 15mm. CPT Confidential and Property 2/5 IIS_CLAA070LC0ACW _Y_V1_Ceramate_091124 CPT Disallow Disclosure, Reproduction or Distribution L : Length[mm], N : Number, φ: Average Diameter Scratch & Fiber [Note2] The definition of Bright dot (1)The defective area of the dot is larger than 50% of one sub-pixel area. (2)The bright dot shall be visible under ND-Filter 2%as following. [Note3] C Area: Center of display area O Area: Outer of display area CPT Confidential and Property 3/5 IIS_CLAA070LC0ACW _Y_V1_Ceramate_091124 CPT Disallow Disclosure, Reproduction or Distribution [Note4] Judge defect dot and adjacent dot as following. Allow below (as A, B, C and D status) adjacent defect dots, including bright and dart adjacent dot. And they will be counted 2 defect dots in total quantity. [Note5] Other condition (1) The defects that are not defined above and considered to be problem shall be reviewed and discussed by both parties. (2) Defects on the Black Matrix, out of Display area, are not considered as a defect or counted. 5. Mechanical : (1) Regarding the mechanical dimension, please refer the Technical Specification. a. The tolerance of mechanical dimension is ± 0.3mm. b. And the tolerance of length of lamp cable is ± 5.0mm. (2) Label position CPT Confidential and Property 4/5 IIS_CLAA070LC0ACW _Y_V1_Ceramate_091124 CPT Disallow Disclosure, Reproduction or Distribution (3) The code principle of Panel Label. The Panel ID has 15 figures as below: XXXXXXXXXXXXXXX 1st 7th~11th 13th~14th Discrimination Method for manufacture date: In this figures, the 1st, 13th and 14th figure is representative “Year”, “Month” and ”Day”. Ex “Year”: “8”→2008, “9”→2009, “0”→2010, “1”→2011 Ex “Month”: “1”, “2”, “3”,‧‧‧”9”, “A”, “B”, “C” (“A”→October) Ex “Day”: “1”, “2”, “3”,‧‧‧”9”, “A”, “B”, “C” ‧‧‧”V” (“A”→10th) Discrimination Method for serial number of panel: In this figures, the 7th, 8th, 9th and 10th figure is representative the serial number of panel. Ex: 0001, 0002, ……, 9998, 9999, A000, A001… Discrimination Method for assembling: In this figures, the 11th figure is representative of the key part source. Ex.1: XXXXXXXXXX1XXXX → Assembling 1(01x) Ex.2: XXXXXXXXXX2XXXX → Assembling 2(02x) 6. Handling precaution (1) Don’t disassemble and reassemble the module by self. (禁止自行拆解。) (2) Acid, alkali, alcohol or touched directly by hand will damage the display. (酸性、鹼性、酒精或手的直接接觸將會損傷顯示面。) (3) Static electricity will damage the module. Please configure grounding device. (靜電會損傷模組。請裝配接地設備。) (4) The strong vibration, shock, twist or bend will cause material damage, even module broken. (強烈的衝擊、震動、扭轉或彎曲將會造成原材損傷，甚至面板破裂) 。 (5) It is easy to cause image sticking while displaying the same pattern for very long time. (長期顯示同一畫面亦造成影像殘留。) (6) The response time, brightness and performance will vary from different temperature. (反應時間、亮度與均勻性會因溫度而有所變化。) CPT Confidential and Property 5/5 IIS_CLAA070LC0ACW _Y_V1_Ceramate_091124