IP9008 5-CH MOTOR DRIVE IC+ 2-Reg controllers DESCRIPTIONS IP9008 is a 5-CH motor driver for CD-P/VCDP/DVDP systems. It is composed of 4-CH BTL drivers, 1-CH forward /reverse controlled DC motor driver and two adjustable regulator controllers. ORDER INFORMATION FEATURES - 4-CH BTL driver. - 1-CH forward/reverse controlled DC motor driver. - Built-in two adjustable regulator controllers. - Built-in TSD (thermal shut down) circuit. - Built-in mute circuit. - Built-in power save circuit. - Operating supply voltage (4.3V~13.2V). * L : Lead Free * TF : Tape & Reel packing * L-TF : Lead Free and Tape & Reel packing June. 2005 (Rev. 4) 28SSOPH-375B Device Package Operating Temp IP9008 28SSOPH-375A -35OC ~ +85OC IP9008-TF 28SSOPH-375A -35OC ~ +85OC IP9008L 28SSOPH-375A -35OC ~ +85OC IP9008L-TF 28SSOPH-375A -35OC ~ +85OC IP9008 28SSOPH-375B -35OC ~ +85OC IP9008-TF 28SSOPH-375B -35OC ~ +85OC IP9008L 28SSOPH-375B -35OC ~ +85OC IP9008L-TF 28SSOPH-375B -35OC ~ +85OC www.interpionsemi.com -1- IP9008 5-CH MOTOR DRIVE IC+ 2-Reg controllers PIN CONNECTIONS PIN DESCRIPTIONS NO SYMBOL I/O DESCRIPTION NO SYMBOL I/O DESCRIPTION 1 FWD I Loading motor forward input 15 VO4+ O CH4 driver output(+) 2 REV I Loading motor reverse input 16 VO4- O CH4 driver output(-) 3 CTL I Loading motor speed control 17 VO3+ O CH3 driver output(+) 4 PS I Power save 18 VO3- O CH3 driver output(-) 5 IN1 I CH1 input 19 GND - Ground 6 IN2 I CH2 input 20 PVCC2 - Power supply 2 7 SVCC - Signal power supply 21 MUTE I Mute 8 PVCC1 - Power supply 1 22 IN3 I CH3 input 9 VOL- O Loading driver output(-) 23 IN4 I CH4 input 10 VOL+ O Loading driver output(+) 24 REOadj1 O Adjustable regulator 1 feedback 11 VO2- O CH2 driver output(-) 25 REBadj1 O Adjustable regulator 1 control 12 VO2+ O CH2 driver output(+) 26 REOadj2 O Adjustable regulator 2 feedback 13 VO1- O CH1 driver output(-) 27 REBadj2 O Adjustable regulator 2 control 14 VO1+ O CH1 driver output(+) 28 BIAS I Bias June. 2005 (Rev. 4) www.interpionsemi.com -2- IP9008 5-CH MOTOR DRIVE IC+ 2-Reg controllers ABSOLUTE MAXIMUM RATINGS CHARACTERISTICS SYMBOL VALUE UNIT Maximum supply voltage VCCmax 15 V Power dissipation Pd 2.3 * W Operating temperature Topr -35 ~ +85 O C Storage temperature Tstg -55 ~ 150 O C Note> 1. When mounted on 50mm X 50mm X 1mm PCB (Phenolic resin material). 2. Power dissipation reduces 18.4 mW/OC for using above Ta=25OC 3. Do not exceed Pd and SOA. Power Dissipation (mW) POWER DISSIPATION CURVE 3 2 1 0 25 50 75 100 125 150 175 Ambient Temperature (°C) RECOMMENDED OPERATING CONDITIONS CHARACTERISTICS SYMBOL VALUE UNIT Signal supply Voltage SVCC 4.3 ~ 13.2 V Power supply Voltage 1 PVCC1 4.3 ~ SVCC V Power supply Voltage 2 PVCC2 4.3 ~ SVCC V June. 2005 (Rev. 4) www.interpionsemi.com -3- IP9008 5-CH MOTOR DRIVE IC+ 2-Reg controllers ELECTRICAL CHARACTERISTICS (SVCC=12.0V,PVCC1=PVCC2=5V, RL=8ohm, Bias=1.65V, Ta = 25OC unless otherwise specified.) CHARACTERISTICS SYMBOL CONDITIONS MIN TYP MAX UNIT Quiescent circuit current Icc No Load - 15 23 mA Power save on current Ips Pin5=GND - 0.5 2.0 mA Power save on voltage Vpson Pin5=sweep - - 0.5 V Power save off voltage Vpsoff Pin5=sweep 2.0 - - V Vin=Vref -80 - +80 mV 3.6 4.0 - V 17 19 21 dB [ BTL DRIVE PART ] Output offset voltage Voos Maximum output voltage Voms Closed-loop voltage gain Avfs Vin=0.1Vrms, f=1kHz Mute on voltage Vmon Pin21=sweep - - 0.5 V Mute off voltage Vmoff Pin21=sweep 1.5 - - V Mute pin current Imp Pin21=5.0V 200 300 uA Bias pin current Ibias Pin28=2.5V 80 120 uA Vout* 0.95 Vout Vout* 1.05 V - [ ADJUSTABLE REGULATOR PART ] Output voltage VREG IL=100mA Load Regulation ΔVom IL=0->200mA -50 0 50 mV Line Regulation ΔVcc Vcc=6->10V,IL=100mA -50 0 50 mV [LOADING DRIVER PART] Input high level voltage Vih - 1.5 - - V Input low level voltage Vil - - - 0.5 V FWD/REV pin current Iin Pin1=Pin2=5.0V - 200 300 uA Maximum output voltage Vo RL=25 ohm 9.0 10 - V Voltage gain Gvf Pin3=sweep 7 9 11 dB June. 2005 (Rev. 4) www.interpionsemi.com -4- IP9008 5-CH MOTOR DRIVE IC+ 2-Reg controllers TYPICAL APPLICATION CIRCUIT June. 2005 (Rev. 4) www.interpionsemi.com -5- IP9008 5-CH MOTOR DRIVE IC+ 2-Reg controllers ELECTRICAL CHARACTERISTICS CURVES Icc vs. Vcc ICC(mA) 30 25 SVcc=PVcc1=PVcc2 20 15 10 5 0 6 8 10 12 Vcc(V) Icc vs. Temp Icc(mA) 32 28 24 20 16 12 8 -25 0 25 50 75 100 Temp June. 2005 (Rev. 4) www.interpionsemi.com -6- IP9008 5-CH MOTOR DRIVE IC+ 2-Reg controllers ELECTRICAL CHARACTERISTICS CURVES (Continued) Vom vs. Vcc (CH1,2,3,4) Vom(V) 8 Vref=2.5V, Vin=5V 6 4 2 0 6 8 10 12 14 Vcc(V) Avf vs. Vcc(CH1,2,3,4) Avf(dB) 32 28 24 20 16 12 8 4 0 6 8 10 12 14 Vcc(V) June. 2005 (Rev. 4) www.interpionsemi.com -7- IP9008 5-CH MOTOR DRIVE IC+ 2-Reg controllers ELECTRICAL CHARACTERISTICS CURVES (Continued) Vom(CH1,2,3,4) vs. Temp Vom(v) 10 8 6 4 2 0 -25 0 25 50 75 100 Temp Gvf (Loading) vs. Temp Gvf(dB) 12 11 10 9 8 7 6 5 -25 0 25 50 75 100 Temp June. 2005 (Rev. 4) www.interpionsemi.com -8- IP9008 5-CH MOTOR DRIVE IC+ 2-Reg controllers ELECTRICAL CHARACTERISTICS CURVES (Continued) Vreg vs. Vcc Vreg(V) 2.1 2.0 1.9 1.8 1.7 1.6 1.5 1.4 6 8 10 12 Vcc(V) Vreg vs. IL Vreg(V) 2.1 2.0 1.9 1.8 1.7 1.6 1.5 1.4 0 50 100 150 200 250 300 IL(mA) June. 2005 (Rev. 4) www.interpionsemi.com -9- IP9008 5-CH MOTOR DRIVE IC+ 2-Reg controllers ELECTRICAL CHARACTERISTICS CURVES (Continued) Vreg vs. Temp Vreg(v) 2.1 2.0 1.9 1.8 1.7 1.6 1.5 -25 0 25 50 75 100 Temp June. 2005 (Rev. 4) www.interpionsemi.com - 10 - IP9008 5-CH MOTOR DRIVE IC+ 2-Reg controllers PACKAGE DIMENSION(28SSOPH-375A) June. 2005 (Rev. 4) www.interpionsemi.com - 11 - IP9008 5-CH MOTOR DRIVE IC+ 2-Reg controllers PACKAGE DIMENSION(28SSOPH-375B) June. 2005 (Rev. 4) www.interpionsemi.com - 12 -