IP9009 5-CH Motor Drive IC with Regulator and Reset controllers DESCRIPTIONS IP9009 is a 5-CH motor driver with LDO regulator and reset controller. It is suitable for CD-P/VCD-P/DVD-P systems. The motor driver part is composed of four BTL drivers and one forward/reverse controlled DC motor driver. FEATURES ORDER INFORMATION - 4-CH BTL driver. - 1-CH forward/reverse controlled DC motor driver. - Built-in adjustable LDO regulator controller. - Built-in reset controller. - Built-in TSD (thermal shut down) circuit. - Built-in mute circuit. - Built-in power save circuit. * L : Lead Free * TF : Tape & Reel packing * L-TF : Lead Free and Tape & Reel packing June. 2005 (Rev. 3) 28SSOPH-375B Device Package Operating Temp IP9009 28SSOPH-375A -35OC ~ +85OC IP9009-TF 28SSOPH-375A -35OC ~ +85OC IP9009L 28SSOPH-375A -35OC ~ +85OC IP9009L-TF 28SSOPH-375A -35OC ~ +85OC IP9009 28SSOPH-375B -35OC ~ +85OC IP9009-TF 28SSOPH-375B -35OC ~ +85OC IP9009L 28SSOPH-375B -35OC ~ +85OC IP9009L-TF 28SSOPH-375B -35OC ~ +85OC www.interpionsemi.com -1- IP9009 5-CH Motor Drive IC with Regulator and Reset controllers PIN CONNECTIONS PIN DESCRIPTIONS NO SYMBOL I/O DESCRIPTION NO SYMBOL I/O DESCRIPTION 1 FWD I Loading motor forward input 15 VO4+ O CH4 driver output(+) 2 REV I Loading motor reverse input 16 VO4- O CH4 driver output(-) 3 CTL I Loading motor speed control 17 VO3+ O CH3 driver output(+) 4 PS I Power save 18 VO3- O CH3 driver output(-) 5 IN1 I CH1 input 19 GND - Ground 6 IN2 I CH2 input 20 PVCC2 - Power supply 2 7 SVCC - Signal power supply 21 MUTE I Mute 8 PVCC1 - Power supply 1 22 IN3 I CH3 input 9 VOL- O Loading driver output(-) 23 IN4 I CH4 input 10 VOL+ O Loading driver output(+) 24 Vdet I Reset controller input 11 VO2- O CH2 driver output(-) 25 Reset O Reset controller output 12 VO2+ O CH2 driver output(+) 26 REOadj O Adjustable regulator feedback 13 VO1- O CH1 driver output(-) 27 REBadj O Adjustable regulator control 14 VO1+ O CH1 driver output(+) 28 BIAS I Bias June. 2005 (Rev. 3) www.interpionsemi.com -2- IP9009 5-CH Motor Drive IC with Regulator and Reset controllers ABSOLUTE MAXIMUM RATINGS CHARACTERISTICS SYMBOL VALUE UNIT Maximum supply voltage VCCmax 15 V Power dissipation Pd 2.3 * W Operating temperature Topr -35 ~ +85 O C Storage temperature Tstg -55 ~ 150 O C Note> 1. When mounted on 50mm X 50mm X 1mm PCB (Phenolic resin material). 2. Power dissipation reduces 18.4 mW/OC for using above Ta=25OC 3. Do not exceed Pd and SOA. Power Dissipation (mW) POWER DISSIPATION CURVE 3 2 1 0 25 50 75 100 125 150 175 Ambient Temperature (°C) RECOMMENDED OPERATING CONDITIONS CHARACTERISTICS SYMBOL VALUE UNIT Signal supply Voltage SVCC 4.3 ~ 13.2 V Power supply Voltage 1 PVCC1 4.3 ~ SVCC V Power supply Voltage 2 PVCC2 4.3 ~ SVCC V June. 2005 (Rev. 3) www.interpionsemi.com -3- IP9009 5-CH Motor Drive IC with Regulator and Reset controllers ELECTRICAL CHARACTERISTICS (SVCC=12.0V,PVCC1=PVCC2=5V, RL=12ohm, Bias=1.65V, Ta = 25OC unless otherwise specified.) CHARACTERISTICS SYMBOL CONDITIONS MIN TYP MAX UNIT Quiescent circuit current Icc No Load - 20 30 mA Power save on current Ips Pin5=GND - 0.5 2.0 mA Power save on voltage Vpson Pin5=sweep - - 0.5 V Power save off voltage Vpsoff Pin5=sweep 2.0 - - V Vout* 0.95 Vout Vout* 1.05 V [ ADJUSTABLE REGULATOR PART ] Output voltage VREG IL=100mA Load Regulation ΔVom IL=0->200mA -50 0 50 mV Line Regulation ΔVcc Vcc=6->10V,IL=100mA -50 0 50 mV Detecting voltage Vdet Pin24=sweep (low->high) 2.6 2.9 3.2 V Hysteresis voltage ΔVdet - 50 - mV Maximum output sink current Isink 3 6 - mA Output saturation voltage Vsat RL=1k ohm - - 0.4 V Output offset voltage Voos Vin=Vref -100 - +100 mV Maximum output voltage Voms 3.6 4.0 - V Closed-loop voltage gain Avfs Vin=0.1Vrms, f=1kHz 17 19 21 dB Mute on voltage Vmon Pin21=sweep - - 0.5 V Mute off voltage Vmoff Pin21=sweep 1.5 - - V Mute pin current Imp Pin21=5.0V 200 300 uA Bias pin current Ibias Pin28=2.5V 80 120 uA [ RESET CONTROLLER PART ] [ BTL DRIVE PART ] June. 2005 (Rev. 3) www.interpionsemi.com -4- IP9009 5-CH Motor Drive IC with Regulator and Reset controllers ELECTRICAL CHARACTERISTICS (SVCC=12.0V,PVCC1=PVCC2=5V, RL=12ohm, Bias=1.65V, Ta = 25OC unless otherwise specified.) CHARACTERISTICS SYMBOL CONDITIONS MIN TYP MAX UNIT [ LOADING DRIVER PART ] Input high level voltage Vih 1.5 - - V Input low level voltage Vil - - 0.5 V FWD/REV pin current Iin Pin1=Pin2=5.0V - 200 300 uA Maximum output voltage Vo RL=25 ohm 9.0 10 - V Voltage gain Gvf Pin3=sweep 7 9 11 dB June. 2005 (Rev. 3) www.interpionsemi.com -5- IP9009 5-CH Motor Drive IC with Regulator and Reset controllers TYPICAL APPLICATION CIRCUIT June. 2005 (Rev. 3) www.interpionsemi.com -6- IP9009 5-CH Motor Drive IC with Regulator and Reset controllers PACKAGE DIMENSION(28SSOPH-375A) June. 2005 (Rev. 3) www.interpionsemi.com -7- IP9009 5-CH Motor Drive IC with Regulator and Reset controllers PACKAGE DIMENSION(28SSOPH-375B) June. 2005 (Rev. 3) www.interpionsemi.com -8-