NSD05-S 5W DC-DC Regulated Single Output series Features : Wide 4:1 DC input range Protections: Short circuit / Overload / Over voltage 1000VDC I/O isolation Cooling by free air convection Built-in remote ON-OFF control 100% full load burn-in test Low cost High reliability 2 years warranty SPECIFICATION MODEL OUTPUT NSD05-12S3 NSD05-12S5 NSD05-12S12 NSD05-12S15 NSD05-48S3 NSD05-48S5 NSD05-48S12 NSD05-48S15 DC VOLTAGE 3.3V 5V 12V 15V 3.3V 5V 12V 15V RATED CURRENT 1.2A 1A 0.42A 0.33A 1.2A 1A 0.42A 0.33A CURRENT RANGE 0 ~ 1.2A 0 ~ 1A 0 ~ 0.42A 0 ~ 0.33A 0 ~ 1.2A 0 ~ 1A 0 ~ 0.42A 0 ~ 0.33A RATED POWER 3.96W 5W 5.04W 4.95W 3.96W 5W 5.04W 4.95W CAPACITIVE LOAD (max.) 1000uF 1000uF 120uF 120uF 1000uF 1000uF 120uF 120uF 1.0% 1.0% 1.0% 2.0% 1.0% 1.0% 1.0% RIPPLE & NOISE (max.) Note.2 75mVp-p VOLTAGE TOLERANCE Note.3 2.0% max. LINE REGULATION 1.0% 2.0% LOAD REGULATION INPUT RATED DC INPUT VOLTAGE RANGE EFFICIENCY (Typ.) 12VDC 9.2 ~ 36VDC 72% DC CURRENT SHUTDOWN IDLE CURRENT 0.7A/12VDC 5mA/12VDC OVERLOAD PROTECTION FUNCTION ENVIRONMENT OVER VOLTAGE(CLAMP) SHORT CIRCUIT ON/OFF CONTROL -25 ~ +70 STORAGE TEMP., HUMIDITY 83% 78% -40 ~ +85 83% 85% 13.5 ~ 16.5V 16.2 ~ 19.8V 0.2A/48VDC 5mA/48VDC 0% ~ 95% RH max. EMC IMMUNITY MTBF , 0 ~ 95% RH 0.03%/ (0~60 IEC60950-1 CB approved by TUV I/P-O/P:1KVDC I/P-O/P:100M Ohms / 500VDC / 25 / 70% RH Compliance to EN55022 (CISPR22) Class B Compliance to EN61000-4-2,3,4,5,6,8; EN55024, light industry level, criteria A 914.4K hrs min. MIL-HDBK-217F (25 ) 40.6*25.4*8.3mm (1.6"*1"*0.327") (L*W*H) 0.007Kg; 700pcs/5.9Kg/0.97CUFT DIMENSION PACKING NOTE 82% Above 105% rated output power Protection type : Over power limiting, recovers automatically after fault condition is removed 3.8 ~ 4.6V 5.6 ~ 6.8V 13.5 ~ 16.5V 16.2 ~ 19.8V 3.8 ~ 4.6V 5.6 ~ 6.8V Recovers automatically after fault condition is removed Logic "1" or open circuit : ON Logic "0" or short to PIN2 : OFF WORKING TEMP. WORKING HUMIDITY TEMP. COEFFICIENT SAFETY STANDARDS SAFETY & ISOLATION VOLTAGE ISOLATION RESISTANCE EMC (Note 4) EMC EMISSION OTHERS 76% 48VDC 18 ~ 72VDC 75% 1. All parameters NOT specially mentioned are measured at 12, 48VDC input, rated load and 25 of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. For guidance on how to perform these EMC tests, please refer to EMI testing of component power supplies. (as available on http://www.meanwell.com) 5. To insure proper operation, a 47uF/100V electrolytic capacitor with Esr <1 must be added to the input line. 6.EMC filter suggestion(TBD): 5.5uH + Vin - + 680uF + PSU Vo - File Name:NSD05-S-SPEC 2011-08-17 NSD05-S 5W DC-DC Regulated Single Output Mechanical Specification series Unit:mm[inch] 40.6 [1.6] 30.48 [1.2] 4 2 22.86[0.9] 5 2.54[0.1] 10.16[0.4] 15.24[0.6] 25.4[1] 2.54[0.1] 10.16 [0.4] 1 8.3 [0.327] 6 [0.236] 3 [0.118] 1.5[0.059] 3 0.64mm square pins Pin No. Assignment Pin No. 1 2 3 Assignment +INPUT -INPUT(GND) +VOUT Pin No. 4 5 Assignment -VOUT CONTROL Block Diagram fosc : 350KHz POWER SWITCHING I/P O.L.P. RECTIFIERS & FILTER DETECTION CIRCUIT PWM CONTROL C TRL +VOUT -VOUT O.V.P. Derating Curve ON/OFF Control 1 +VIN +VOUT 3 100 2 LOAD -VIN 80 75 5 LOAD (%) 60 C TRL -VOUT 4 40 CONTROL INPUT.....................................PIN5 20 CONTROL COMMON................................PIN2 LOGIC COMPATIBILITY......CMOS OR OPEN COLLECTOR TTL -25 -10 0 10 20 30 40 50 AMBIENT TEMPERATURE ( ) 60 70 (HORIZONTAL) CONTROL VOLTAGE ON............+5.5VDC min OR OPEN CIRCUIT OFF......+2.5VDC max. OR SHORT TO PIN2 File Name:NSD05-S-SPEC 2011-08-17