TPA0223 2-W MONO AUDIO POWER AMPLIFIER WITH HEADPHONE DRIVE SLOS277C – JANUARY 2000 – REVISED NOVEMBER 2002 D Ideal for Notebook Computers, PDAs, and D D D D D D D D D D D Other Small Portable Audio Devices 2 W Into 4-Ω From 5-V Supply 0.6 W Into 4-Ω From 3-V Supply Stereo Head Phone Drive Separate Inputs for the Mono (BTL) Signal and Stereo (SE) Left/Right Signals Wide Power Supply Compatibility 3 V to 5 V Meets PC99 Desktop Specs (Target) Low Supply Current – 11 mA Typical at 5 V – 10 mA Typical at 3 V Shutdown Control . . . 1 µA Typical Shutdown Pin Is TTL Compatible –40°C to 85°C Operating Temperature Range Space-Saving, Thermally-Enhanced MSOP Packaging DGQ PACKAGE (TOP VIEW) MONO–IN SHUTDOWN VDD BYPASS RIN 1 2 3 4 5 10 9 8 7 6 LO/MO– LIN GND ST/MN RO/MO+ description The TPA0223 is a 2-W mono bridge-tied-load (BTL) amplifier designed to drive speakers with as low as 4-Ω impedance. The amplifier can be reconfigured on the fly to drive two stereo single-ended (SE) signals into head phones. This makes the device ideal for small notebook computers, PDAs, digital personal audio players, anyplace a mono speaker and stereo headphones are required. From a 5-V supply, the TPA0223 can deliver 2 W of power into a 4-Ω speaker. The gain of the input stage is set by the user-selected input resistor and a 50-kΩ internal feedback resistor (AV = – RF/ RI). The power stage is internally configured with a gain of –1.25 V/V in SE mode, and –2.5 V/V in BTL mode. Thus, the overall gain of the amplifier is 62.5 kΩ/ RI in SE mode and 125 kΩ/ RI in BTL mode. The input terminals, high-impedance CMOS inputs, can be used as summing nodes. The TPA0223 is available in the 10-pin thermally-enhanced MSOP package (DGQ) and operates over an ambient temperature range of –40°C to 85°C. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Copyright 2002, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 TPA0223 2-W MONO AUDIO POWER AMPLIFIER WITH HEADPHONE DRIVE SLOS277C – JANUARY 2000 – REVISED NOVEMBER 2002 CB 4 p140 BYPASS VDD 3 VDD GND 8 VDD BYPASS Mono Audio Input Right Audio Input CI CI 50 kΩ RI 1.25*R 100 kΩ 1 MONO-IN 5 RIN M U X R – – + CC RO/MO+ 6 + RI BYPASS BYPASS 100 kΩ 50 kΩ Stereo/Mono Control ST/MN 7 LO/MO– 10 50 kΩ 1.25*R Left Audio Input CI RI 9 LIN M U X R – – + CC + 1 kΩ BYPASS BYPASS From System Control 2 SHUTDOWN Shutdown and Depop Circuitry AVAILABLE OPTIONS TA PACKAGED DEVICES MSOP† (DGQ) MSOP SYMBOLIZATION – 40°C to 85°C TPA0223DGQ AEI † The DGQ package are available taped and reeled. To order a taped and reeled part, add the suffix R to the part number (e.g., TPA0223DGQR). 2 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 TPA0223 2-W MONO AUDIO POWER AMPLIFIER WITH HEADPHONE DRIVE SLOS277C – JANUARY 2000 – REVISED NOVEMBER 2002 Terminal Functions TERMINAL NAME NO. I/O DESCRIPTION I BYPASS is the tap to the voltage divider for internal mid-supply bias. This terminal should be connected to a 0.1-µF to 1-µF capacitor. BYPASS 4 GND 8 LIN 9 I Left-channel input terminal LO/MO– 10 O Left-output in SE mode and mono negative output in BTL mode. MONO-IN 1 I Mono input terminal RIN 5 I Right-channel input terminal RO/MO+ 6 O Right-output in SE mode and mono positive output in BTL mode SHUTDOWN 2 I SHUTDOWN places the entire device in shutdown mode when held low. TTL compatible input. ST/MN 7 I Selects between stereo and mono mode. When held high, the amplifier is in SE stereo mode, while held low, the amplifier is in BTL mono mode. VDD 3 I VDD is the supply voltage terminal. Ground terminal absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage, VDD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 V Input voltage range, VI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to VDD +0.3 V Continuous total power dissipation . . . . . . . . . . . . . . . . . . . . . internally limited (see Dissipation Rating Table) Operating free-air temperature range, TA (see Table 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 40°C to 85°C Operating junction temperature range, TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 40°C to 150°C Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. DISSIPATION RATING TABLE PACKAGE DGQ TA ≤ 25°C 2.14 W‡ DERATING FACTOR 17.1 mW/°C TA = 70°C 1.37 W TA = 85°C 1.11 W ‡ See the Texas Instruments document, PowerPAD Thermally Enhanced Package Application Report (SLMA002), for more information on the PowerPAD package. The thermal data was measured on a PCB layout based on the information in the section entitled Texas Instruments Recommended Board for PowerPAD on page 33 of that document. recommended operating conditions ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ Supply voltage, VDD High-level input High level in ut voltage, VIH ST/MN VDD = 3 V VDD = 5 V SHUTDOWN Low-level Low level in input ut voltage, VIL ST/MN MIN MAX 2.5 5.5 UNIT V 2.7 4.5 V 2 VDD = 3 V VDD = 5 V 1.65 2.75 V ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ SHUTDOWN 0.8 Operating free-air temperature, TA – 40 85 °C PowerPAD is a trademark of Texas Instruments. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 3 TPA0223 2-W MONO AUDIO POWER AMPLIFIER WITH HEADPHONE DRIVE SLOS277C – JANUARY 2000 – REVISED NOVEMBER 2002 electrical characteristics at specified free-air temperature, VDD = 3 V, TA = 25°C (unless otherwise noted) ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁ ÁÁÁÁÁÁ ÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁ ÁÁÁ ÁÁÁ ÁÁÁ ÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ PARAMETER TEST CONDITIONS MIN |VOO| Output offset voltage (measured differentially) ST/MN = 0, RL = 4 Ω, SHUTDOWN = 2 V IDD IDD(SD) Supply current VDD = 2.5 V, SHUTDOWN = 2 V SHUTDOWN = 0 |IIH| High level input current High-level |IIL| Low level input current Low-level RF Feedback resistor Supply current, shutdown mode TYP MAX mV 10 13 mA 1 10 µA SHUTDOWN, VDD = 3.3 V, ST/MN, VDD = 3.3 V, VI = VDD VI = VDD 1 SHUTDOWN, VDD = 3.3 V, VI = 0 V VI = 0 V 1 ST/MN, VDD = 3.3 V, VDD = 2.5 V, RL = 4 Ω, ST/MN = 1.375 V, SHUTDOWN = 2 V 1 1 48 UNIT 30 50 57 µA A µA A kΩ operating characteristics, VDD = 3 V, TA = 25°C, RL = 4 Ω ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁ ÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁ ÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ PARAMETER PO power see Note 1 Output power, THD + N Total harmonic distortion plus noise BOM Maximum output power bandwidth TEST CONDITIONS MIN THD = 1%, BTL mode THD = 0.1%, SE mode, PO = 500 mW, Gain = 2, f = 20 Hz to 20 kHz TYP MAX UNIT 660 RL = 32 Ω mW 33 0.3% THD = 2% 20 kHz NOTE 1: Output power is measured at the output terminals of the device at f = 1 kHz. electrical characteristics at specified free-air temperature, VDD = 5 V, TA = 25°C (unless otherwise noted) ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁ ÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁ PARAMETER TEST CONDITIONS MIN TYP MAX |VOO| Output offset voltage (measured differentially) ST/MN = 0, RL = 4 Ω, SHUTDOWN = 2 V IDD IDD(SD) Supply current SHUTDOWN = 2 V Supply current, shutdown mode SHUTDOWN = 0 V High level input current High-level SHUTDOWN, VDD = 5.5 V, ST/MN, VDD = 5.5 V, VI = VDD VI = VDD 1 |IIH| Low level input current Low-level SHUTDOWN, VDD = 5.5 V, VI = 0 V VI = 0 V 1 |IIL| ST/MN, VDD = 5.5 V, UNIT 30 mV 11 17 mA 1 10 µA 1 1 µA A µA A operating characteristics, VDD = 5 V, TA = 25°C, RL = 4 Ω ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁ ÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ PARAMETER PO power see Note 1 Output power, THD + N Total harmonic distortion plus noise BOM Maximum output power bandwidth TEST CONDITIONS THD = 1%, BTL mode THD = 0.1%, SE mode, PO = 1 W, Gain = 2.5, RL = 32 Ω f = 20 Hz to 20 kHz THD = 2% NOTE 1: Output power is measured at the output terminals of the device at f = 1 kHz. 4 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 MIN TYP MAX UNIT 2 W 95 mW 0.2% 20 kHz TPA0223 2-W MONO AUDIO POWER AMPLIFIER WITH HEADPHONE DRIVE SLOS277C – JANUARY 2000 – REVISED NOVEMBER 2002 TYPICAL CHARACTERISTICS Table of Graphs FIGURE Supply ripple rejection ratio vs Frequency IDD Supply current vs Supply voltage 1, 2 3 vs Supply voltage 4, 5 PO Output power vs Load resistance 6, 7 vs Frequency THD+N Total harmonic distortion plus noise Vn Output noise voltage 8, 9, 10, 11 12, 13, 14, 15, 16, 17 vs Output power vs Frequency 18, 19 Closed loop response 20, 21 SUPPLY RIPPLE REJECTION RATIO vs FREQUENCY SUPPLY RIPPLE REJECTION RATIO vs FREQUENCY 0 0 RL = 8 Ω CB = 1 µF Mode = Mono –20 RL = 32 Ω CB = 1 µF Mode = Stereo –10 Supply Ripple Rejection Ratio – dB Supply Ripple Rejection Ratio – dB –10 –30 –40 –50 –60 –70 –80 –20 –30 –40 –50 –60 –70 –80 –90 –90 –100 –100 20 100 1k 10 k 20 k 20 100 1k 10 k 20 k f – Frequency – Hz f – Frequency – Hz Figure 1 Figure 2 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 5 TPA0223 2-W MONO AUDIO POWER AMPLIFIER WITH HEADPHONE DRIVE SLOS277C – JANUARY 2000 – REVISED NOVEMBER 2002 TYPICAL CHARACTERISTICS OUTPUT POWER vs SUPPLY VOLTAGE SUPPLY CURRENT vs SUPPLY VOLTAGE 3 18 VDD From Low to High Mode = Stereo RL = Open THD+N = 1% f = 1 kHz Mode = Mono AV = 8 dB 2.5 14 PO – Output Power – W I DD – Supply Current – mA 16 TA = 25 °C 12 10 8 6 RL = 4 Ω 2 RL = 8 Ω 1.5 1 4 0.5 2 0 0 0 0.5 1 1.5 2 2.5 3 3.5 4 VDD – Supply Voltage – V 4.5 5 5.5 3 3.5 4 4.5 5 VDD – Supply Voltage – V Figure 3 Figure 4 OUTPUT POWER vs LOAD RESISTANCE OUTPUT POWER vs SUPPLY VOLTAGE 2.5 500 THD+N = 1% f = 1 kHz Mode = Stereo AV = 2 dB THD+N = 1% f = 1 kHz Mode = Mono AV = 8 dB 2 PO – Output Power – W 400 PO – Output Power – mW 5.5 RL = 8 Ω 300 200 1.5 VDD = 5 V 1 RL = 32 Ω 100 0.5 0 0 VDD = 3 V 3 3.5 4 4.5 5 VDD – Supply Voltage – V 5.5 0 20 30 Figure 6 POST OFFICE BOX 655303 40 50 RL – Load Resistance – Ω Figure 5 6 10 • DALLAS, TEXAS 75265 60 TPA0223 2-W MONO AUDIO POWER AMPLIFIER WITH HEADPHONE DRIVE SLOS277C – JANUARY 2000 – REVISED NOVEMBER 2002 TYPICAL CHARACTERISTICS OUTPUT POWER vs LOAD RESISTANCE TOTAL HARMONIC DISTORTION PLUS NOISE vs FREQUENCY THD+N = 1% f = 1 kHz Mode = Stereo AV = 2 dB 600 PO – Output Power – mW THD+N – Total Harmonic Distortion Plus Noise – % 700 500 400 300 VDD = 5 V 200 100 VDD = 3 V 0 0 10 20 30 40 50 RL – Load Resistance – Ω 60 1 VDD = 3 V PO = 250 mW RL = 8 Ω Mode = Mono 0.1 AV = 20 dB AV = 8 dB 0.01 0.001 20 100 1k f – Frequency – Hz Figure 7 Figure 8 1 VDD = 5 V PO = 1 W RL = 8 Ω Mode = Mono 0.1 AV = 20 dB AV = 8 dB 0.01 0.001 100 1k f – Frequency – Hz TOTAL HARMONIC DISTORTION PLUS NOISE vs FREQUENCY THD+N – Total Harmonic Distortion Plus Noise – % THD+N – Total Harmonic Distortion Plus Noise – % TOTAL HARMONIC DISTORTION PLUS NOISE vs FREQUENCY 20 10 k 20 k 10 k 20 k 1 VDD = 3 V PO = 25 mW RL = 32 Ω Mode = Stereo 0.1 AV = 14 dB 0.01 AV = 2 dB 0.001 20 100 1k 10 k 20 k f – Frequency – Hz Figure 9 Figure 10 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 7 TPA0223 2-W MONO AUDIO POWER AMPLIFIER WITH HEADPHONE DRIVE SLOS277C – JANUARY 2000 – REVISED NOVEMBER 2002 TYPICAL CHARACTERISTICS 1 VDD = 5 V PO = 75 mW RL = 32 Ω Mode = Stereo 0.1 AV = 14 dB 0.01 AV = 2 dB 0.001 20 100 TOTAL HARMONIC DISTORTION PLUS NOISE vs OUTPUT POWER THD+N – Total Harmonic Distortion Plus Noise – % THD+N – Total Harmonic Distortion Plus Noise – % TOTAL HARMONIC DISTORTION PLUS NOISE vs FREQUENCY 1k f – Frequency – Hz 10 k 20 k 10 20 kHz 1 15 kHz 0.1 1 kHz 20 Hz 0.01 VDD = 3 V RL = 4 Ω Mode = Mono AV = 8 dB 0.001 10 m Figure 11 VDD = 3 V RL = 8 Ω Mode = Mono AV = 8 dB 20 kHz 15 kHz 0.1 1 kHz 20 Hz 0.01 100 m PO – Output Power – W 1 2 10 VDD = 3 V RL = 32 Ω Mode = Stereo AV = 2 dB 1 0.1 20 kHz 15 kHz 0.01 20 Hz 0.001 10 m Figure 13 8 2 TOTAL HARMONIC DISTORTION PLUS NOISE vs OUTPUT POWER THD+N – Total Harmonic Distortion Plus Noise – % THD+N – Total Harmonic Distortion Plus Noise – % 10 0.001 10 m 1 Figure 12 TOTAL HARMONIC DISTORTION PLUS NOISE vs OUTPUT POWER 1 100 m PO – Output Power – W 1 kHz 100 m PO – Output Power – mW Figure 14 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 TPA0223 2-W MONO AUDIO POWER AMPLIFIER WITH HEADPHONE DRIVE SLOS277C – JANUARY 2000 – REVISED NOVEMBER 2002 TYPICAL CHARACTERISTICS TOTAL HARMONIC DISTORTION PLUS NOISE vs OUTPUT POWER 10 THD+N – Total Harmonic Distortion Plus Noise – % THD+N – Total Harmonic Distortion Plus Noise – % TOTAL HARMONIC DISTORTION PLUS NOISE vs OUTPUT POWER VDD = 5 V RL = 4 Ω Mode = Mono AV = 8 dB 1 20 kHz 15 kHz 0.1 1 kHz 20 Hz 0.01 0.001 10 m 100 m 1 PO – Output Power – W 10 10 VDD = 5 V RL = 8 Ω Mode = Mono AV = 8 dB 1 20 KHz 15 kHz 0.1 20 Hz 0.01 0.001 10 m 100 m PO – Output Power – W Figure 15 Vn – Output Noise Voltage – µV RMS THD+N – Total Harmonic Distortion Plus Noise – % 1M VDD = 5 V RL = 32 Ω Mode = Stereo AV = 2 dB 15 kHz 20 kHz 0.01 20 Hz 1 kHz 0.001 10 m 2 OUTPUT NOISE VOLTAGE vs FREQUENCY 10 0.1 1 Figure 16 TOTAL HARMONIC DISTORTION PLUS NOISE vs OUTPUT POWER 1 1 kHz 100 m PO – Output Power – W 1 VDD = 5 V RL = 8 Ω Mode = Mono AV = 8 dB 100 10 1 20 100 Figure 17 1k f – Frequency – Hz 10 k 20 k Figure 18 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 9 TPA0223 2-W MONO AUDIO POWER AMPLIFIER WITH HEADPHONE DRIVE SLOS277C – JANUARY 2000 – REVISED NOVEMBER 2002 TYPICAL CHARACTERISTICS OUTPUT NOISE VOLTAGE vs FREQUENCY CLOSED LOOP RESPONSE 180° 30 VDD = 5 V RL = 32 Ω Mode = Stereo AV = 2 dB 20 10 VDD = 5 V RL = 4 Ω Mode = Mono AV = 8 dB 135° Gain 90° 100 0 45° Phase –10 0° –20 –45° –30 –90° –40 –135° 10 –50 10 1 20 100 1k f – Frequency – Hz 10 k 20 k 100 1k 10k f – Frequency – Hz Figure 19 Figure 20 CLOSED LOOP RESPONSE 30 Gain – dB 10 135° Gain 90° 0 45° Phase –10 0° –20 –45° –30 –90° –40 –135° –50 10 100 1k 10k 100k f – Frequency – Hz Figure 21 10 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 –180° 1M Phase 20 180° VDD = 5 V RL = 32 Ω Mode = Stereo AV = 2 dB Phase Gain – dB Vn – Output Noise Voltage – µV RMS 1M 100k –180° 1M TPA0223 2-W MONO AUDIO POWER AMPLIFIER WITH HEADPHONE DRIVE SLOS277C – JANUARY 2000 – REVISED NOVEMBER 2002 APPLICATION INFORMATION gain setting via input resistance The gain of the input stage is set by the user-selected input resistor and a 50-kΩ internal feedback resistor. However, the power stage is internally configured with a gain of –1.25 V/V in SE mode, and –2.5 V/V in BTL mode. Thus, the feedback resistor (RF) is effectively 62.5 kΩ in SE mode and 125 kΩ in BTL mode. Therefore, the overall gain can be calculated using equations (1) and (2). A + –125 kW V R I (BTL) A + –62.5 kW V R I (SE) (1) (2) The –3 dB frequency can be calculated using equation 3: ƒ –3 dB + 1 2p R C I i (3) If the filter must be more accurate, the value of the capacitor should be increased while the value of the resistor to ground should be decreased. In addition, the order of the filter could be increased. input capacitor, Ci In the typical application an input capacitor, Ci, is required to allow the amplifier to bias the input signal to the proper dc level for optimum operation. In this case, Ci and the input resistance of the amplifier, RI, form a high-pass filter with the corner frequency determined in equation 4. –3 dB f c(highpass) + (4) 1 2 p RI Ci fc The value of Ci is important to consider as it directly affects the bass (low frequency) performance of the circuit. Consider the example where RI is 710 kΩ and the specification calls for a flat bass response down to 40 Hz. Equation 2 is reconfigured as equation 5. 1 C + i 2p R f c I (5) In this example, CI is 5.6 nF so one would likely choose a value in the range of 5.6 nF to 1 µF. A further consideration for this capacitor is the leakage path from the input source through the input network (Ci) and the feedback network to the load. This leakage current creates a dc offset voltage at the input to the amplifier that reduces useful headroom, especially in high gain applications. For this reason a low-leakage tantalum or ceramic capacitor is the best choice. When polarized capacitors are used, the positive side of the capacitor should face the amplifier input in most applications as the dc level there is held at VDD/2, which is likely higher than the source dc level. Note that it is important to confirm the capacitor polarity in the application. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 11 TPA0223 2-W MONO AUDIO POWER AMPLIFIER WITH HEADPHONE DRIVE SLOS277C – JANUARY 2000 – REVISED NOVEMBER 2002 APPLICATION INFORMATION input capacitor, Ci (continued) power supply decoupling, C(S) The TPA0223 is a high-performance CMOS audio amplifier that requires adequate power supply decoupling to ensure the output total harmonic distortion (THD) is as low as possible. Power supply decoupling also prevents oscillations for long lead lengths between the amplifier and the speaker. The optimum decoupling is achieved by using two capacitors of different types that target different types of noise on the power supply leads. For higher frequency transients, spikes, or digital hash on the line, a good low equivalent-series-resistance (ESR) ceramic capacitor, typically 0.1 µF placed as close as possible to the device VDD lead, works best. For filtering lower-frequency noise signals, a larger aluminum electrolytic capacitor of 10 µF or greater placed near the audio power amplifier is recommended. midrail bypass capacitor, C(BYP) The midrail bypass capacitor, C(BYP), is the most critical capacitor and serves several important functions. During start-up or recovery from shutdown mode, C(BYP) determines the rate at which the amplifier starts up. The second function is to reduce noise produced by the power supply caused by coupling into the output drive signal. This noise is from the midrail generation circuit internal to the amplifier, which appears as degraded PSRR and THD+N. Bypass capacitor, C(BYP), values of 0.47 µF to 1 µF ceramic or tantalum low-ESR capacitors are recommended for the best THD and noise performance. output-coupling capacitor, C(C) In the typical single-supply SE configuration, an output-coupling capacitor (C(C)) is required to block the dc bias at the output of the amplifier, thus preventing dc currents in the load. As with the input-coupling capacitor, the output-coupling capacitor and impedance of the load form a high-pass filter governed by equation 6. –3 dB f c(high) + 1 2 p R L C (C) (6) fc The main disadvantage, from a performance standpoint, is that the load impedances are typically small, which drives the low-frequency corner higher, degrading the bass response. Large values of C(C) are required to pass low frequencies into the load. Consider the example where a C(C) of 330 µF is chosen and loads vary from 3 Ω, 4 Ω, 8 Ω, 32 Ω, 10 kΩ, to 47 kΩ. Table 1 summarizes the frequency response characteristics of each configuration. 12 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 TPA0223 2-W MONO AUDIO POWER AMPLIFIER WITH HEADPHONE DRIVE SLOS277C – JANUARY 2000 – REVISED NOVEMBER 2002 APPLICATION INFORMATION Table 1. Common Load Impedances vs Low Frequency Output Characteristics in SE Mode RL C(C) 330 µF Lowest Frequency 3Ω 4Ω 330 µF 120 Hz 161 Hz 8Ω 330 µF 60 Hz 32 Ω 330 µF Ą15 Hz 10,000 Ω 330 µF 0.05 Hz 47,000 Ω 330 µF 0.01 Hz As Table 1 indicates, most of the bass response is attenuated into a 4-Ω load, an 8-Ω load is adequate, headphone response is good, and drive into line level inputs (a home stereo for example) is exceptional. Furthermore, the total amount of ripple current that must flow through the capacitor must be considered when choosing the component. As shown in the application circuit, one coupling capacitor must be in series with the mono loudspeaker for proper operation of the stereo-mono switching circuit. For a 4-Ω load, this capacitor must be able to handle about 700 mA of ripple current for a continuous output power of 2 W. using low-ESR capacitors Low-ESR capacitors are recommended throughout this applications section. A real (as opposed to ideal) capacitor can be modeled simply as a resistor in series with an ideal capacitor. The voltage drop across this resistor minimizes the beneficial effects of the capacitor in the circuit. The lower the equivalent value of this resistance the more the real capacitor behaves like an ideal capacitor. bridged-tied load versus single-ended mode Figure 22 shows a Class-AB audio power amplifier (APA) in a BTL configuration. The TPA0223 BTL amplifier consists of two Class-AB amplifiers driving both ends of the load. There are several potential benefits to this differential drive configuration, but initially consider power to the load. The differential drive to the speaker means that as one side is slewing up, the other side is slewing down, and vice versa. This, in effect, doubles the voltage swing on the load as compared to a ground referenced load. Plugging 2 × VO(PP) into the power equation, where voltage is squared, yields 4× the output power from the same supply rail and load impedance. See equation 7. V V (RMS) + V Power + O(PP) 2 Ǹ2 (7) 2 (RMS) R L POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 13 TPA0223 2-W MONO AUDIO POWER AMPLIFIER WITH HEADPHONE DRIVE SLOS277C – JANUARY 2000 – REVISED NOVEMBER 2002 APPLICATION INFORMATION bridged-tied load versus single-ended mode (continued) VDD VO(PP) 2x VO(PP) RL VDD –VO(PP) Figure 22. Bridge-Tied Load Configuration In a typical computer sound channel operating at 5 V, bridging raises the power into an 8-Ω speaker from a singled-ended (SE, ground reference) limit of 250 mW to 1 W. In sound power, that is a 6-dB improvement— which is loudness that can be heard. In addition to increased power, there are frequency response concerns. Consider the single-supply SE configuration shown in Figure 23. A coupling capacitor is required to block the dc offset voltage from reaching the load. These capacitors can be quite large (approximately 33 µF to 1000 µF) so they tend to be expensive, heavy, occupy valuable PCB area, and have the additional drawback of limiting low-frequency performance of the system. This frequency-limiting effect is due to the high pass filter network created with the speaker impedance and the coupling capacitance and is calculated with equation 8. fc + 1 2p R C L (C) (8) For example, a 68-µF capacitor with an 8-Ω speaker would attenuate low frequencies below 293 Hz. The BTL configuration cancels the dc offsets, which eliminates the need for the blocking capacitors. Low-frequency performance is then limited only by the input network and speaker response. Cost and PCB space are also minimized by eliminating the bulky coupling capacitor. VDD –3 dB VO(PP) C(C) RL VO(PP) fc Figure 23. Single-Ended Configuration and Frequency Response 14 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 TPA0223 2-W MONO AUDIO POWER AMPLIFIER WITH HEADPHONE DRIVE SLOS277C – JANUARY 2000 – REVISED NOVEMBER 2002 APPLICATION INFORMATION bridged-tied load versus single-ended mode (continued) Increasing power to the load does carry a penalty of increased internal power dissipation. The increased dissipation is understandable considering that the BTL configuration produces 4× the output power of the SE configuration. Internal dissipation versus output power is discussed further in the crest factor and thermal considerations section. single-ended operation In SE mode (see Figure 22 and Figure 23), the load is driven from the primary amplifier output for each channel (LO and RO, terminals 6 and 10) The amplifier switches to single-ended operation when the ST/MN terminal is held high. input MUX operation The input MUX allows two separate inputs to be applied to the amplifier. When the ST/MN terminal is held high, the headphone inputs (LIN and RIN) are active. When the ST/MN terminal is held low, the line BTL input (MONO-IN) is active. BTL amplifier efficiency Class-AB amplifiers are inefficient. The primary cause of inefficiencies is the voltage drop across the output stage transistors. There are two components of the internal voltage drop. One is the headroom or dc voltage drop that varies inversely to output power. The second component is due to the sinewave nature of the output. The total voltage drop can be calculated by subtracting the RMS value of the output voltage from VDD. The internal voltage drop multiplied by the RMS value of the supply current, IDDrms, determines the internal power dissipation of the amplifier. An easy-to-use equation to calculate efficiency starts out as being equal to the ratio of power from the power supply to the power delivered to the load. To accurately calculate the RMS and average values of power in the load and in the amplifier, the current and voltage waveform shapes must first be understood. See Figure 24. IDD VO IDD(avg) V(LRMS) Figure 24. Voltage and Current Waveforms for BTL Amplifiers Although the voltages and currents for SE and BTL are sinusoidal in the load, currents from the supply are very different between SE and BTL configurations. In an SE application the current waveform is a half-wave rectified shape, whereas in BTL it is a full-wave rectified waveform. This means RMS conversion factors are different. Keep in mind that for most of the waveform both the push and pull transistors are not on at the same time, which supports the fact that each amplifier in the BTL device only draws current from the supply for half the waveform. The following equations are the basis for calculating amplifier efficiency. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 15 TPA0223 2-W MONO AUDIO POWER AMPLIFIER WITH HEADPHONE DRIVE SLOS277C – JANUARY 2000 – REVISED NOVEMBER 2002 APPLICATION INFORMATION BTL amplifier efficiency (continued) Efficiency of a BTL amplifier + where PL + V LRMS RL 2 PL (9) P SUP 2 V V , and V LRMS + P , therefore, P L + P Ǹ2 2 RL and P SUP + V DD I DDavg 1 I DDavg + p and ŕ p 0 VP 1 sin(t) dt + p RL VP RL [cos(t)] p 2V P + 0 p RL therefore, P SUP + 2 V DD V P p RL substituting PL and PSUP into equation 9, 2 Efficiency of a BTL amplifier + where VP + VP 2 RL 2 V DD V P p RL + p VP 4 V DD Ǹ2 P L RL therefore, h BTL + p Ǹ2 PL R L (10) 4 V DD PL = Power devilered to load PSUP = Power drawn from power supply VLRMS = RMS voltage on BTL load RL = Load resistance VP = Peak voltage on BTL load IDDavg = Average current drawn from the power supply VDD = Power supply voltage ηBTL = Efficiency of a BTL amplifier Table 2 employs equation 10 to calculate efficiencies for four different output power levels. Note that the efficiency of the amplifier is quite low for lower power levels and rises sharply as power to the load is increased resulting in a nearly flat internal power dissipation over the normal operating range. Note that the internal dissipation at full output power is less than in the half power range. Calculating the efficiency for a specific system is the key to proper power supply design. For a stereo 1-W audio system with 8-Ω loads and a 5-V supply, the maximum draw on the power supply is almost 3.25 W. Table 2. Efficiency Vs Output Power in 5-V 8-Ω BTL Systems Output Power (W) Efficiency (%) Peak Voltage (V) Internal Dissipation (W) 0.25 31.4 2.00 0.55 0.50 44.4 2.83 0.62 1.00 62.8 70.2 4.00 4.47† 0.59 1.25 † High peak voltages cause the THD to increase. 16 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 0.53 TPA0223 2-W MONO AUDIO POWER AMPLIFIER WITH HEADPHONE DRIVE SLOS277C – JANUARY 2000 – REVISED NOVEMBER 2002 APPLICATION INFORMATION BTL amplifier efficiency (continued) A final point to remember about Class-AB amplifiers (either SE or BTL) is how to manipulate the terms in the efficiency equation to utmost advantage when possible. Note that in equation 10, VDD is in the denominator. This indicates that as VDD goes down, efficiency goes up. crest factor and thermal considerations Class-AB power amplifiers dissipate a significant amount of heat in the package under normal operating conditions. A typical music CD requires 12 dB to 15 dB of dynamic range, or headroom above the average power output, to pass the loudest portions of the signal without distortion. In other words, music typically has a crest factor between 12 dB and 15 dB. When determining the optimal ambient operating temperature, the internal dissipated power at the average output power level must be used. The TPA0223 data sheet shows that when the TPA0223 is operating from a 5-V supply into a 4-Ω speaker 4-W peaks are available. Converting watts to dB: P dB + 10Log PW P ref + 10 Log 4 W + 6 dB 1W (11) Subtracting the headroom restriction to obtain the average listening level without distortion yields: 6 dB – 15 dB = –9 dB (15-dB crest factor) 6 dB – 12 dB = –6 dB (12-dB crest factor) 6 dB – 9 dB = –3 dB (9-dB crest factor) 6 dB – 6 dB = 0 dB (6-dB crest factor) 6 dB – 3 dB = 3 dB (3-dB crest factor) Converting dB back into watts: P W + 10 PdBń10 + + + + + + P ref (12) 63 mW (18-dB crest factor) 125 mW (15-dB crest factor) 250 mW (12-dB crest factor) 500 mW (9-dB crest factor) 1000 mW (6-dB crest factor) 2000 mW (3-dB crest factor) This is valuable information to consider when attempting to estimate the heat dissipation requirements for the amplifier system. Comparing the absolute worst case, which is 2 W of continuous power output with a 3 dB crest factor, against 12 dB and 15 dB applications drastically affects maximum ambient temperature ratings for the system. Table 3 shows maximum ambient temperatures and TPA223 internal power dissipation for various output-power levels. Table 3. TPA0223 Power Rating, 5-V, 3-Ω, Mono PEAK OUTPUT POWER (W) AVERAGE OUTPUT POWER POWER DISSIPATION (W) 4 2 W (3-dB crest factor) 1.7 4 1000 mW (6-dB crest factor) 1.6 6°C 4 500 mW (9-dB crest factor) 1.4 24°C 4 250 mW (12-dB crest factor) 1.1 51°C 4 125 mW (15-dB crest factor) 0.8 78°C 4 63 mW (18-dB crest factor) 0.6 96°C POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 MAXIMUM AMBIENT TEMPERATURE – 3°C 17 TPA0223 2-W MONO AUDIO POWER AMPLIFIER WITH HEADPHONE DRIVE SLOS277C – JANUARY 2000 – REVISED NOVEMBER 2002 APPLICATION INFORMATION crest factor and thermal considerations (continued) Table 4. TPA0223 Power Rating, 5-V, 8-Ω, Stereo PEAK OUTPUT POWER (W) AVERAGE OUTPUT POWER POWER DISSIPATION (W) MAXIMUM AMBIENT TEMPERATURE 2.5 1250 mW (3-dB crest factor) 0.55 100°C 2.5 1000 mW (4-dB crest factor) 0.62 94°C 2.5 500 mW (7-dB crest factor) 0.59 97°C 2.5 250 mW (10-dB crest factor) 0.53 102°C The maximum dissipated power, PDmax, is reached at a much lower output power level for an 4-Ω load than for an 8-Ω load. As a result, this simple formula for calculating PDmax may be used for a 4-Ω application: P Dmax + 2V 2 DD (13) p 2R L However, in the case of a 8-Ω load, the PDmax occurs at a point well above the normal operating power level. The amplifier may therefore be operated at a higher ambient temperature than required by the PDmax formula for an 8-Ω load. The maximum ambient temperature depends on the heat sinking ability of the PCB system. The derating factor for the DGQ package is shown in the dissipation rating table (see page 4). Converting this to ΘJA: Θ JA + 1 1 + + 58.48°CńW 0.0171 Derating Factor (14) To calculate maximum ambient temperatures, first consider that the numbers from the dissipation graphs are per channel so the dissipated power needs to be doubled for two channel operation. Given ΘJA, the maximum allowable junction temperature, and the total internal dissipation, the maximum ambient temperature can be calculated with the following equation. The maximum recommended junction temperature for the TPA0223 is 150°C. The internal dissipation figures are taken from the Power Dissipation vs Output Power graphs. T A Max + T J Max * Θ JA P D + 150 * 58.48 (0.8 2) + 56°C (15-dB crest factor) (15) NOTE: Internal dissipation of 0.8 W is estimated for a 2-W system with 15-dB crest factor per channel. Tables 3 and 4 show that for some applications no airflow is required to keep junction temperatures in the specified range. The TPA0223 is designed with thermal protection that turns the device off when the junction temperature surpasses 150°C to prevent damage to the IC. Tables 3 and 4 were calculated for maximum listening volume without distortion. When the output level is reduced the numbers in the table change significantly. Also, using 8-Ω speakers dramatically increases the thermal performance by increasing amplifier efficiency. ST/MN (stereo/mono) operation The ability of the TPA0223 to easily switch between mono BTL and stereo SE modes is one of its most important cost saving features. This feature eliminates the requirement for an additional headphone amplifier in applications where an internal speaker is driven in BTL mode but external stereo headphone or speakers must be accommodated. When ST/MN is held high, the input mux selects the RIN and LIN inputs and the output is in stereo SE mode. When ST/MN is held low, the input mux selects the mono-in input and the output is in mono BTL mode. Control of the ST/MN input can be from a logic-level CMOS source or, more typically, from a switch-controlled resistor divider network as shown in Figure 25. 18 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 TPA0223 2-W MONO AUDIO POWER AMPLIFIER WITH HEADPHONE DRIVE SLOS277C – JANUARY 2000 – REVISED NOVEMBER 2002 APPLICATION INFORMATION ST/MN (stereo/mono) operation (continued) CB 4 VDD 3 BYPASS VDD GND Ci 50 kΩ RI 1.25*R 100 kΩ 1 Right Audio Input 5 Ci VDD BYPASS 50 kΩ Mono Audio Input 1 kΩ 8 MONO-IN RIN RI M U X – R – + CC RO/MO+ 6 + BYPASS BYPASS 100 kΩ 50 kΩ Stereo/Mono Control 50 kΩ ST/MN 7 LO/MO– 10 50 kΩ 1.25*R Left Audio Input Ci RI 9 M U X LIN – R – + CC + 1 kΩ BYPASS From System Control BYPASS 2 SHUTDOWN Shutdown and Depop Circuitry Figure 25. TPA0223 Resistor Divider Network Circuit Using a readily available 1/8-in. (3,5 mm) stereo headphone jack, the control switch is closed when no plug is inserted. When closed, the 100-kΩ/1-kΩ divider pulls the ST/MN input low. When a plug is inserted, the 1-kΩ resistor is disconnected and the ST/MN input is pulled high. The mono speaker is also physically disconnected from the RO/MO+ output so that no sound is heard from the speaker while the headphones are inserted. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 19 PACKAGE OPTION ADDENDUM www.ti.com 6-Dec-2006 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty TPA0223DGQR ACTIVE MSOPPower PAD DGQ 10 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPA0223DGQRG4 ACTIVE MSOPPower PAD DGQ 10 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Lead/Ball Finish MSL Peak Temp (3) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 27-Jan-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device TPA0223DGQR Package Package Pins Type Drawing MSOPPower PAD DGQ 10 SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) 2500 330.0 12.4 Pack Materials-Page 1 5.3 B0 (mm) K0 (mm) P1 (mm) 3.4 1.4 8.0 W Pin1 (mm) Quadrant 12.0 Q1 PACKAGE MATERIALS INFORMATION www.ti.com 27-Jan-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) TPA0223DGQR MSOP-PowerPAD DGQ 10 2500 358.0 335.0 35.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2012, Texas Instruments Incorporated