TPA0213 2-W MONO AUDIO POWER AMPLIFIER WITH HEADPHONE DRIVE SLOS276C – JANUARY 2000 – REVISED APRIL 2001 D D D D D D D D D D D Ideal for Notebook Computers, PDAs, and Other Small Portable Audio Devices 2 W Into 4 Ω From 5-V Supply 0.6 W Into 4 Ω From 3-V Supply Stereo Headphone Drive Separate Inputs for the Mono (BTL) Signal, and Stereo (SE) Left/Right Signals Wide Power Supply Compatibility 2.5 V to 5.5 V Low Supply Current – 4.2 mA Typical at 5 V – 3.6 mA Typical at 3 V Shutdown Control . . . 1 µA Typical Shutdown Pin Is TTL Compatible –40°C to 85°C Operating Temperature Range Space-Saving, Thermally-Enhanced MSOP Packaging DGQ PACKAGE (TOP VIEW) MONO–IN SHUTDOWN VDD BYPASS RIN 1 2 3 4 5 10 9 8 7 6 LO/MO– LIN GND ST/MN RO/MO+ description The TPA0213 is a 2-W mono bridge-tied-load (BTL) amplifier designed to drive speakers with as low as 4-Ω impedance. The amplifier can be reconfigured on-the-fly to drive two stereo single-ended (SE) signals into headphones. This makes the device ideal for use in small notebook computers, PDAs, personal digital audio players, anywhere a mono speaker and stereo headphones are required. From a 5-V supply, the TPA0213 can deliver 2-W of power into a 4-Ω speaker. The gain of the input stage is set by the user-selected input resistor and a 50-kΩ internal feedback resistor (AV = – RF/RI). The power stage is internally configured with a gain of –1.25 V/V in SE mode, and –2.5 V/V in BTL mode. Thus, the overall gain of the amplifier is –62.5 kΩ/RI in SE mode and –125 kΩ/RI in BTL mode. The TPA0213 is available in the 10-pin thermally-enhanced MSOP package (DGQ) and operates over an ambient temperature range of –40°C to 85°C. AVAILABLE OPTIONS TA PACKAGED DEVICES MSOP† (DGQ) MSOP SYMBOLIZATION – 40°C to 85°C TPA0213DGQ AEH † The DGQ package are available taped and reeled. To order a taped and reeled part, add the suffix R to the part number (e.g., TPA0213DGQR). Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PowerPAD is a trademark of Texas Instruments Copyright 2001, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 TPA0213 2-W MONO AUDIO POWER AMPLIFIER WITH HEADPHONE DRIVE SLOS276C – JANUARY 2000 – REVISED APRIL 2001 functional block diagram CB 4 VDD 3 BYPASS VDD GND Ci 50 kΩ RI 1.25*R 100 kΩ 1 Right Audio Input 5 Ci VDD BYPASS 50 kΩ Mono Audio Input 1 kΩ 8 MONO-IN RIN RI M U X – R – + CC RO/MO+ 6 + BYPASS BYPASS 100 kΩ 50 kΩ Stereo/Mono Control 50 kΩ ST/MN 7 LO/MO– 10 50 kΩ 1.25*R Left Audio Input Ci RI 9 LIN M U X – R – + + 1 kΩ BYPASS BYPASS From System Control 2 2 SHUTDOWN CC Shutdown and Depop Circuitry POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 TPA0213 2-W MONO AUDIO POWER AMPLIFIER WITH HEADPHONE DRIVE SLOS276C – JANUARY 2000 – REVISED APRIL 2001 Terminal Functions TERMINAL NAME NO. I/O DESCRIPTION MONO-IN 1 I Mono input terminal SHUTDOWN 2 I SHUTDOWN places the entire device in shutdown mode when held low. TTL compatible input. VDD BYPASS 3 I 4 I VDD is the supply voltage terminal. BYPASS is the tap to the voltage divider for internal mid-supply bias. This terminal should be connected to a 0.1-µF to 1-µF capacitor. RIN 5 I Right-channel input terminal RO/MO+ 6 O Right-output in SE mode and mono positive output in BTL mode ST/MN 7 I Selects between stereo and mono mode. When held high, the amplifier is in SE stereo mode, while held low, the amplifier is in BTL mono mode. GND 8 LIN 9 I Left-channel input terminal LO/MO– 10 O Left-output in SE mode and mono negative output in BTL mode. Ground terminal absolute maximum ratings over operating free-air temperature range (unless otherwise noted)§ Supply voltage, VDD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 V Input voltage, VI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to VDD +0.3 V Continuous total power dissipation . . . . . . . . . . . . . . . . . . . . . internally limited (see Dissipation Rating Table) Operating free-air temperature range, TA (see Table 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 40°C to 85°C Operating junction temperature range, TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 40°C to 150°C Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C § Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. DISSIPATION RATING TABLE PACKAGE DGQ TA ≤ 25°C 2.14 W¶ DERATING FACTOR 17.1 mW/°C TA = 70°C 1.37 W TA = 85°C 1.11 W ¶ Please see the Texas Instruments document, PowerPAD Thermally Enhanced Package Application Report (literature number SLMA002), for more information on the PowerPAD package. The thermal data was measured on a PCB layout based on the information in the section entitled Texas Instruments Recommended Board for PowerPAD on page 33 of the before mentioned document. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 3 TPA0213 2-W MONO AUDIO POWER AMPLIFIER WITH HEADPHONE DRIVE SLOS276C – JANUARY 2000 – REVISED APRIL 2001 recommended operating conditions ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ Supply voltage, VDD High-level input voltage, VIH VDD = 3 V VDD = 5 V ST/MN MAX 2.5 5.5 V V 4.5 2 VDD = 3 V VDD = 5 V ST/MN UNIT 2.7 SHUTDOWN Low-level input voltage, VIL MIN 1.65 V 2.75 ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ SHUTDOWN 0.8 Operating free-air temperature, TA – 40 °C 85 electrical characteristics at specified free-air temperature, VDD = 3 V, TA = 25°C (unless otherwise noted) ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ PARAMETER TEST CONDITIONS VIO = 0, VDD = 2.9 V to 3.1 V, Gain = 8 dB VDD = 3.3 V, VDD = 3.3 V, VI = VDD VI = 0 MIN TYP MAX UNIT |VOO| Output offset voltage (measured differentially) PSRR Power supply rejection ratio |IIH| High-level input current |IIL| Low-level input current zi Input impedance 50 IDD IDD(SD) Supply current 3.6 5.5 mA 1 10 µA BTL mode 30 mV 1 µA 65 dB µA 1 Supply current, shutdown mode kΩ operating characteristics, VDD = 3 V, TA = 25°C, RL = 4 Ω, f = 1 kHz (unless otherwise noted) ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁ ÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ PARAMETER PO Output power, power see Note 1 THD + N Total harmonic distortion plus noise BOM Maximum output power bandwidth Vn TEST CONDITIONS THD = 1%, BTL mode THD = 0.1%, SE mode, PO = 500 mW, Gain = 8 dB, f = 20 Hz to 20 kHz Supply ripple rejection ratio f = 1 kHz kHz, CB = 0 0.47 47 µF Noise output voltage CB = 0 0.47 47 µF, µF f = 20 Hz to 20 kHz POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 TYP 660 RL = 32 Ω 33 MAX UNIT mW 0.2% THD = 2% NOTE 1: Output power is measured at the output terminals of the device at f = 1 kHz. 4 MIN 20 BTL mode 52 SE mode 62 BTL mode 42 SE mode 21 kHz dB µVRMS TPA0213 2-W MONO AUDIO POWER AMPLIFIER WITH HEADPHONE DRIVE SLOS276C – JANUARY 2000 – REVISED APRIL 2001 electrical characteristics at specified free-air temperature, VDD = 5 V, TA = 25°C (unless otherwise noted) ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁ ÁÁ ÁÁÁ ÁÁÁÁÁÁÁÁÁÁ ÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ PARAMETER TEST CONDITIONS VIO = 0, VDD = 4.9 V to 5.1 V, Gain = 8 dB VDD = 5.5 V, VDD = 5.5 V, VI = VDD VI = 0 MIN TYP |VOO| Output offset voltage (measured differentially) PSRR Power supply rejection ratio |IIH| High-level input current |IIL| Low-level input current zi Input impedance 50 IDD IDD(SD) Supply current BTL mode MAX UNIT 30 mV 1 µA 1 µA 4.2 6.3 mA 1 10 µA 62 Supply current, shutdown mode dB kΩ operating characteristics, VDD = 5 V, TA = 25°C, RL = 4 Ω ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁ ÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁ ÁÁÁÁÁÁ ÁÁÁÁÁ ÁÁÁ ÁÁÁ ÁÁÁ ÁÁÁ ÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁ ÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ PARAMETER TEST CONDITIONS THD = 0.3%, BTL mode PO Output power, power see Note 1 THD = 0.1%, SE mode, THD + N Total harmonic distortion plus noise PO = 1.5 W, f = 20 Hz to 20 kHz BOM Maximum output power bandwidth Gain = 6 dB, THD = 2% Vn Supply ripple rejection ratio f = 1 kHz kHz, CB = 0 0.47 47 µF Noise output voltage CB = 0 0.47 47 µF, µF f = 20 Hz to 20 kHz MIN RL = 32 Ω TYP MAX UNIT 2 W 90 mW 0.2% 20 BTL mode 52 SE mode 62 BTL mode 42 SE mode 21 kHz dB µVRMS NOTE 1: Output power is measured at the output terminals of the device at f = 1 kHz. TYPICAL CHARACTERISTICS Table of Graphs FIGURE vs Output power 1, 3, 5, 6, 8, 10 THD+N Total harmonic distortion plus noise Vn Output noise voltage vs Frequency 11 Power supply rejection ratio vs Frequency 12, 13 vs Frequency POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 2, 4, 7, 9 5 TPA0213 2-W MONO AUDIO POWER AMPLIFIER WITH HEADPHONE DRIVE SLOS276C – JANUARY 2000 – REVISED APRIL 2001 TYPICAL CHARACTERISTICS TOTAL HARMONIC DISTORTION + NOISE vs OUTPUT POWER TOTAL HARMONIC DISTORTION + NOISE vs FREQUENCY 1 VDD =3 V Mono/BTL f = 1 kHz Gain = 8 dB THD+N – Total Harmonic Distortion + Noise THD+N – Total Harmonic Distortion + Noise 10 1 RL = 4 Ω RL = 8 Ω .10 .01 0.001 0.01 0.1 1 PO – Output Power – W VDD = 3 V Mono/BTL RL = 8 Ω PO = 250 mW 0.1 Gain = 20 dB Gain = 8 dB 0.01 0.001 10 10 100 Figure 2 TOTAL HARMONIC DISTORTION + NOISE vs OUTPUT POWER TOTAL HARMONIC DISTORTION + NOISE vs FREQUENCY 1 VDD = 3 V Mono/BTL RL = 8 Ω Gain = 8 dB THD+N – Total Harmonic Distortion + Noise THD+N – Total Harmonic Distortion + Noise 10 f = 20 kHz 0.1 f = 1 kHz f = 20 Hz 0.01 0.001 0.01 0.1 1 2 VDD = 3 V Stereo/SE Gain = 1.9 dB 0.1 RL = 32 Ω PO = 25 mW 0.01 RL = 10 kΩ VO = 1 VRMS 0.001 10 PO – Output Power – W 100 Figure 4 POST OFFICE BOX 655303 1k f – Frequency – Hz Figure 3 6 10k 20k f – Frequency – Hz Figure 1 1 1k • DALLAS, TEXAS 75265 10k 20k TPA0213 2-W MONO AUDIO POWER AMPLIFIER WITH HEADPHONE DRIVE SLOS276C – JANUARY 2000 – REVISED APRIL 2001 TYPICAL CHARACTERISTICS TOTAL HARMONIC DISTORTION + NOISE vs OUTPUT POWER TOTAL HARMONIC DISTORTION + NOISE vs OUTPUT POWER 10 VDD = 3 V Stereo/SE RL = 32 Ω Gain = 1.9 dB THD+N – Total Harmonic Distortion + Noise THD+N – Total Harmonic Distortion + Noise 10 1 f = 20 kHz 0.1 f = 1 kHz f = 20 Hz 0.01 0.01 VDD = 5 V Mono/BTL f = 1 kHz Gain = 8 dB 1 RL = 4 Ω 0.1 RL = 8 Ω 0.01 0.001 0.1 0.01 PO – Output Power – W 10 Figure 6 TOTAL HARMONIC DISTORTION + NOISE vs FREQUENCY TOTAL HARMONIC DISTORTION + NOISE vs OUTPUT POWER 1 10 VDD = 5 V Mono/BTL RL = 8 Ω PO = 1 W THD+N – Total Harmonic Distortion + Noise THD+N – Total Harmonic Distortion + Noise 1 PO – Output Power – W Figure 5 0.1 Gain = 20 dB Gain = 8 dB 0.01 0.001 10 0.1 100 1k 10k 20k VDD = 5 V Mono/BTL RL = 8 Ω Gain = 8 dB f = 20 kHz 1 f = 1 kHz 0.1 f = 20 Hz 0.01 0.001 f – Frequency – Hz 0.01 0.1 1 2 PO – Output Power – W Figure 7 Figure 8 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 7 TPA0213 2-W MONO AUDIO POWER AMPLIFIER WITH HEADPHONE DRIVE SLOS276C – JANUARY 2000 – REVISED APRIL 2001 TYPICAL CHARACTERISTICS TOTAL HARMONIC DISTORTION + NOISE vs FREQUENCY TOTAL HARMONIC DISTORTION + NOISE vs OUTPUT POWER 10 VDD = 5 V Stereo/SE Gain = 1.9 dB THD+N – Total Harmonic Distortion + Noise THD+N – Total Harmonic Distortion + Noise 1 0.1 RL = 32 Ω PO = 75 mW 0.01 RL = 10 kΩ VO = 1 VRMS 0.001 10 100 1k VDD = 5 V Stereo/SE RL = 32 Ω Gain = 1.9 dB 1 f = 20 kHz 0.1 f = 1 kHz f = 20 Hz 0.01 0.01 10k 20k PO – Output Power – W Figure 10 POWER SUPPLY REJECTION RATIO vs FREQUENCY 0 Mono/BTL RL = 8 Ω Gain = 8 dB Mono/BTL RL = 8 Ω Gain = 20 dB Stereo/SE RL = 32 Ω Gain = 14 dB 100 Stereo/SE RL = 32 Ω Gain = 1.9 dB 1k 10k 20k PSRR – Power Supply Rejection Ratio – dB Vn – Output Noise Voltage – µV 100 –20 VDD = 5 V Mono/BTL Gain = 8 dB CB = 0.47 µF CB = 1 µF CB = 10 µF –40 –60 –80 Bypass = 2.5 V –100 –120 20 f – Frequency – Hz 100 Figure 12 POST OFFICE BOX 655303 1k f – Frequency – Hz Figure 11 8 1 Figure 9 OUTPUT NOISE VOLTAGE vs FREQUENCY 10 10 0.1 f – Frequency – Hz • DALLAS, TEXAS 75265 10k 20k TPA0213 2-W MONO AUDIO POWER AMPLIFIER WITH HEADPHONE DRIVE SLOS276C – JANUARY 2000 – REVISED APRIL 2001 TYPICAL CHARACTERISTICS POWER SUPPLY REJECTION RATIO vs FREQUENCY PSRR – Power Supply Rejection Ratio – dB 0 VDD = 5 V Stereo/SE Gain = 1.9 dB –20 CB = 0.47 µF –40 CB = 1 µF –60 –80 Bypass = 2.5 V –100 –120 20 100 1k 10k 20k f – Frequency – Hz Figure 13 APPLICATION INFORMATION gain setting via input resistance The gain of the input stage is set by the user-selected input resistor and a 50-kΩ internal feedback resistor. However, the power stage is internally configured with a gain of –1.25 V/V in SE mode, and –2.5 V/V in BTL mode. Thus, the feedback resistor (RF) is effectively 62.5 kΩ in SE mode and 125 kΩ in BTL mode. Therefore, the overall gain can be calculated using equations (1) and (2). A A V + –125R kW (BTL) V + –62.5R kW (SE) (1) I (2) I The –3 dB frequency can be calculated using equation 3: ƒ –3 dB + 2p 1R C (3) I i If the filter must be more accurate, the value of the capacitor should be increased while the value of the resistor to ground should be decreased. In addition, the order of the filter could be increased. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 9 TPA0213 2-W MONO AUDIO POWER AMPLIFIER WITH HEADPHONE DRIVE SLOS276C – JANUARY 2000 – REVISED APRIL 2001 APPLICATION INFORMATION input capacitor, Ci In the typical application an input capacitor, Ci, is required to allow the amplifier to bias the input signal to the proper dc level for optimum operation. In this case, Ci and the input resistance of the amplifier, RI, form a high-pass filter with the corner frequency determined in equation 4. –3 dB f c(highpass) + 2 p R1 C (4) I i fc The value of Ci is important to consider as it directly affects the bass (low frequency) performance of the circuit. Consider the example where RI is 710 kΩ and the specification calls for a flat bass response down to 40 Hz. Equation 2 is reconfigured as equation 5. C i + 2 p 1R fc (5) I In this example, CI is 5.6 nF so one would likely choose a value in the range of 5.6 nF to 1 µF. A further consideration for this capacitor is the leakage path from the input source through the input network (Ci) and the feedback network to the load. This leakage current creates a dc offset voltage at the input to the amplifier that reduces useful headroom, especially in high gain applications. For this reason a low-leakage tantalum or ceramic capacitor is the best choice. When polarized capacitors are used, the positive side of the capacitor should face the amplifier input in most applications as the dc level there is held at VDD/2, which is likely higher than the source dc level. Note that it is important to confirm the capacitor polarity in the application. power supply decoupling, C(S) The TPA0213 is a high-performance CMOS audio amplifier that requires adequate power supply decoupling to ensure the output total harmonic distortion (THD) is as low as possible. Power supply decoupling also prevents oscillations for long lead lengths between the amplifier and the speaker. The optimum decoupling is achieved by using two capacitors of different types that target different types of noise on the power supply leads. For higher frequency transients, spikes, or digital hash on the line, a good low equivalent-series-resistance (ESR) ceramic capacitor, typically 0.1 µF placed as close as possible to the device VDD lead, works best. For filtering lower-frequency noise signals, a larger aluminum electrolytic capacitor of 10 µF or greater placed near the audio power amplifier is recommended. midrail bypass capacitor, C(BYP) The midrail bypass capacitor, C(BYP), is the most critical capacitor and serves several important functions. During start-up or recovery from shutdown mode, C(BYP) determines the rate at which the amplifier starts up. The second function is to reduce noise produced by the power supply caused by coupling into the output drive signal. This noise is from the midrail generation circuit internal to the amplifier, which appears as degraded PSRR and THD+N. Bypass capacitor, C(BYP), values of 0.47 µF to 1 µF ceramic or tantalum low-ESR capacitors are recommended for the best THD and noise performance. 10 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 TPA0213 2-W MONO AUDIO POWER AMPLIFIER WITH HEADPHONE DRIVE SLOS276C – JANUARY 2000 – REVISED APRIL 2001 APPLICATION INFORMATION output coupling capacitor, C(C) In the typical single-supply SE configuration, an output coupling capacitor (C(C)) is required to block the dc bias at the output of the amplifier, thus preventing dc currents in the load. As with the input coupling capacitor, the output coupling capacitor and impedance of the load form a high-pass filter governed by equation 6. –3 dB f c(high) + 2 p R1 C (6) L (C) fc The main disadvantage, from a performance standpoint, is the load impedances are typically small, which drives the low-frequency corner higher, degrading the bass response. Large values of C(C) are required to pass low frequencies into the load. Consider the example where a C(C) of 330 µF is chosen and loads vary from 3 Ω, 4 Ω, 8 Ω, 32 Ω, 10 kΩ, to 47 kΩ. Table 1 summarizes the frequency response characteristics of each configuration. Table 1. Common Load Impedances vs Low Frequency Output Characteristics in SE Mode RL C(C) 330 µF Lowest Frequency 3Ω 4Ω 330 µF 120 Hz 8Ω 330 µF 60 Hz 161 Hz 32 Ω 330 µF 15 Hz 10,000 Ω 330 µF 0.05 Hz 47,000 Ω 330 µF 0.01 Hz As Table 1 indicates, most of the bass response is attenuated into a 4-Ω load, an 8-Ω load is adequate, headphone response is good, and drive into line level inputs (a home stereo for example) is exceptional. Furthermore, the total amount of ripple current that must flow through the capacitor must be considered when choosing the component. As shown in the application circuit, one coupling capacitor must be in series with the mono loudspeaker for proper operation of the stereo-mono switching circuit. For a 4-Ω load, this capacitor must be able to handle about 700 mA of ripple current for a continuous output power of 2 W. using low-ESR capacitors Low-ESR capacitors are recommended throughout this applications section. A real (as opposed to ideal) capacitor can be modeled simply as a resistor in series with an ideal capacitor. The voltage drop across this resistor minimizes the beneficial effects of the capacitor in the circuit. The lower the equivalent value of this resistance the more the real capacitor behaves like an ideal capacitor. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 11 TPA0213 2-W MONO AUDIO POWER AMPLIFIER WITH HEADPHONE DRIVE SLOS276C – JANUARY 2000 – REVISED APRIL 2001 APPLICATION INFORMATION bridged-tied load versus single-ended mode Figure 14 shows a Class-AB audio power amplifier (APA) in a BTL configuration. The TPA0213 BTL amplifier consists of two Class-AB amplifiers driving both ends of the load. There are several potential benefits to this differential drive configuration, but initially consider power to the load. The differential drive to the speaker means that as one side is slewing up, the other side is slewing down, and vice versa. This in effect doubles the voltage swing on the load as compared to a ground referenced load. Plugging 2 × VO(PP) into the power equation, where voltage is squared, yields 4× the output power from the same supply rail and load impedance (see equation 7). V + (RMS) V + V Power O(PP) Ǹ 2 2 (7) 2 (RMS) R L VDD VO(PP) RL 2x VO(PP) VDD –VO(PP) Figure 14. Bridge-Tied Load Configuration In a typical computer sound channel operating at 5 V, bridging raises the power into an 8-Ω speaker from a singled-ended (SE, ground reference) limit of 250 mW to 1 W. In sound power, that is a 6-dB improvement— which is loudness that can be heard. In addition to increased power, there are frequency response concerns. Consider the single-supply SE configuration shown in Figure 15. A coupling capacitor is required to block the dc offset voltage from reaching the load. These capacitors can be quite large (approximately 33 µF to 1000 µF) so they tend to be expensive, heavy, occupy valuable PCB area, and have the additional drawback of limiting low-frequency performance of the system. This frequency limiting effect is due to the high pass filter network created with the speaker impedance and the coupling capacitance and is calculated with equation 8. fc 12 + 2 p R 1C (8) L (C) POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 TPA0213 2-W MONO AUDIO POWER AMPLIFIER WITH HEADPHONE DRIVE SLOS276C – JANUARY 2000 – REVISED APRIL 2001 APPLICATION INFORMATION bridged-tied load versus single-ended mode (continued) For example, a 68-µF capacitor with an 8-Ω speaker would attenuate low frequencies below 293 Hz. The BTL configuration cancels the dc offsets, which eliminates the need for the blocking capacitors. Low-frequency performance is then limited only by the input network and speaker response. Cost and PCB space are also minimized by eliminating the bulky coupling capacitor. VDD –3 dB VO(PP) C(C) RL VO(PP) fc Figure 15. Single-Ended Configuration and Frequency Response Increasing power to the load does carry a penalty of increased internal power dissipation. The increased dissipation is understandable considering that the BTL configuration produces 4× the output power of the SE configuration. Internal dissipation versus output power is discussed further in the crest factor and thermal considerations section. single-ended operation In SE mode (see Figure 14 and Figure 15), the load is driven from the primary amplifier output for each channel (LO and RO, terminals 6 and 10) The amplifier switches to single-ended operation when the ST/MN terminal is held high. input MUX operation The input MUX allows two separate inputs to be applied to the amplifier. When the ST/MN terminal is held high, the headphone inputs (LIN and RIN) are active. When the ST/MN terminal is held low, the line BTL input (MONO-IN) is active. BTL amplifier efficiency Class-AB amplifiers are inefficient. The primary cause of inefficiencies is the voltage drop across the output stage transistors. There are two components of the internal voltage drop. One is the headroom or dc voltage drop that varies inversely to output power. The second component is due to the sinewave nature of the output. The total voltage drop can be calculated by subtracting the RMS value of the output voltage from VDD. The internal voltage drop multiplied by the RMS value of the supply current, IDDrms, determines the internal power dissipation of the amplifier. An easy-to-use equation to calculate efficiency starts out as being equal to the ratio of power from the power supply to the power delivered to the load. To accurately calculate the RMS and average values of power in the load and in the amplifier, the current and voltage waveform shapes must first be understood (see Figure 16). POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 13 TPA0213 2-W MONO AUDIO POWER AMPLIFIER WITH HEADPHONE DRIVE SLOS276C – JANUARY 2000 – REVISED APRIL 2001 APPLICATION INFORMATION BTL amplifier efficiency (continued) IDD VO IDD(avg) V(LRMS) Figure 16. Voltage and Current Waveforms for BTL Amplifiers Although the voltages and currents for SE and BTL are sinusoidal in the load, currents from the supply are very different between SE and BTL configurations. In an SE application the current waveform is a half-wave rectified shape, whereas in BTL it is a full-wave rectified waveform. This means RMS conversion factors are different. Keep in mind that for most of the waveform both the push and pull transistors are not on at the same time, which supports the fact that each amplifier in the BTL device only draws current from the supply for half the waveform. The following equations are the basis for calculating amplifier efficiency. Efficiency of a BTL amplifier + PP L (9) SUP Where: PL + and P SUP V LRMS RL 2 , and V LRMS + VDD IDDavg + VǸ2P , 2 therefore, P L I DDavg and + p1 ŕ p 0 + 2VRP VP RL L sin(t) dt + 1p VP RL [cos(t)] p 0 + p2VRP L Therefore, P SUP + 2 VpDDR VP L substituting PL and PSUP into equation 9, 2 Efficiency of a BTL amplifier Where: VP + Ǹ2 PL RL Therefore, h BTL + p VP 2 RL +2 V DD V P p RL DD Ǹ 2 PL RL 4 V DD (10) PL = Power devilered to load PSUP = Power drawn from power supply VLRMS = RMS voltage on BTL load RL = Load resistance 14 + 4p VVP VP = Peak voltage on BTL load IDDavg = Average current drawn from the power supply VDD = Power supply voltage ηBTL = Efficiency of a BTL amplifier POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 TPA0213 2-W MONO AUDIO POWER AMPLIFIER WITH HEADPHONE DRIVE SLOS276C – JANUARY 2000 – REVISED APRIL 2001 APPLICATION INFORMATION BTL amplifier efficiency (continued) Table 2 employs equation 10 to calculate efficiencies for four different output power levels. Note that the efficiency of the amplifier is quite low for lower power levels and rises sharply as power to the load is increased resulting in a nearly flat internal power dissipation over the normal operating range. Note that the internal dissipation at full output power is less than in the half power range. Calculating the efficiency for a specific system is the key to proper power supply design. For a stereo 1-W audio system with 8-Ω loads and a 5-V supply, the maximum draw on the power supply is almost 3.25 W. Table 2. Efficiency Vs Output Power in 5-V 8-Ω BTL Systems Output Power (W) Efficiency (%) Peak Voltage (V) Internal Dissipation (W) 0.25 31.4 2.00 0.55 0.50 44.4 2.83 0.62 1.00 62.8 0.59 1.25 70.2 4.00 4.47† 0.53 † High peak voltages cause the THD to increase. A final point to remember about Class-AB amplifiers (either SE or BTL) is how to manipulate the terms in the efficiency equation to utmost advantage when possible. Note that in equation 10, VDD is in the denominator. This indicates that as VDD goes down, efficiency goes up. crest factor and thermal considerations Class-AB power amplifiers dissipate a significant amount of heat in the package under normal operating conditions. A typical music CD requires 12 dB to 15 dB of dynamic range, or headroom above the average power output, to pass the loudest portions of the signal without distortion. In other words, music typically has a crest factor between 12 dB and 15 dB. When determining the optimal ambient operating temperature, the internal dissipated power at the average output power level must be used. From the TPA0213 data sheet, one can see that when the TPA0213 is operating from a 5-V supply into a 4-Ω speaker 4-W peaks are available. Converting watts to dB: P dB + 10 Log PPW + 10 Log 41 WW + 6 dB (11) ref Subtracting the headroom restriction to obtain the average listening level without distortion yields: 6 dB – 15 dB = –9 dB (15-dB crest factor) 6 dB – 12 dB = –6 dB (12-dB crest factor) 6 dB – 9 dB = –3 dB (9-dB crest factor) 6 dB – 6 dB = 0 dB (6-dB crest factor) 6 dB – 3 dB = 3 dB (3-dB crest factor) POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 15 TPA0213 2-W MONO AUDIO POWER AMPLIFIER WITH HEADPHONE DRIVE SLOS276C – JANUARY 2000 – REVISED APRIL 2001 APPLICATION INFORMATION crest factor and thermal considerations (continued) Converting dB back into watts: PW + 10PdBń10 Pref + 63 mW (18-dB crest factor) + 125 mW (15-dB crest factor) + 250 mW (12-dB crest factor) + 500 mW (9-dB crest factor) + 1000 mW (6-dB crest factor) + 2000 mW (3-dB crest factor) (12) This is valuable information to consider when attempting to estimate the heat dissipation requirements for the amplifier system. Comparing the absolute worst case, which is 2 W of continuous power output with a 3 dB crest factor, against 12 dB and 15 dB applications drastically affects maximum ambient temperature ratings for the system. Using the power dissipation curves for a 5-V, 4-Ω system, the internal dissipation in the TPA0213 and maximum ambient temperatures is shown in Table 3. Table 3. TPA0213 Power Rating, 5-V, 3-Ω, Mono PEAK OUTPUT POWER (W) AVERAGE OUTPUT POWER POWER DISSIPATION (W) MAXIMUM AMBIENT TEMPERATURE 4 2 W (3-dB crest factor) 1.7 – 3°C 4 1000 mW (6-dB crest factor) 1.6 6°C 4 500 mW (9-dB crest factor) 1.4 24°C 4 250 mW (12-dB crest factor) 1.1 51°C 4 125 mW (15-dB crest factor) 0.8 78°C 4 63 mW (18-dB crest factor) 0.6 96°C Table 4. TPA0213 Power Rating, 5-V, 8-Ω, Stereo PEAK OUTPUT POWER (W) AVERAGE OUTPUT POWER POWER DISSIPATION (W) MAXIMUM AMBIENT TEMPERATURE 2.5 1250 mW (3-dB crest factor) 0.55 100°C 2.5 1000 mW (4-dB crest factor) 0.62 94°C 2.5 500 mW (7-dB crest factor) 0.59 97°C 2.5 250 mW (10-dB crest factor) 0.53 102°C The maximum dissipated power, PDmax, is reached at a much lower output power level for an 4-Ω load than for a 8-Ω load. As a result, this simple formula for calculating PDmax may be used for a 4-Ω application: 2V 2 P Dmax + p2RDD (13) L However, in the case of a 8-Ω load, the PDmax occurs at a point well above the normal operating power level. The amplifier may therefore be operated at a higher ambient temperature than required by the PDmax formula for a 8-Ω load. The maximum ambient temperature depends on the heat sinking ability of the PCB system. The derating factor for the DGQ package is shown in the dissipation rating table (see page 4). Converting this to ΘJA: Θ JA 16 1 + Derating1 Factor + 0.0171 + 58.48°CńW POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 (14) TPA0213 2-W MONO AUDIO POWER AMPLIFIER WITH HEADPHONE DRIVE SLOS276C – JANUARY 2000 – REVISED APRIL 2001 APPLICATION INFORMATION crest factor and thermal considerations (continued) To calculate maximum ambient temperatures, first consider that the numbers from the dissipation graphs are per channel so the dissipated power needs to be doubled for two channel operation. Given ΘJA, the maximum allowable junction temperature, and the total internal dissipation, the maximum ambient temperature can be calculated with the following equation. The maximum recommended junction temperature for the TPA0213 is 150°C. The internal dissipation figures are taken from the Power Dissipation vs Output Power graphs. T A Max + TJ Max * ΘJA PD + 150 * 58.48 (0.8 2) + 56°C (15-dB crest factor) (15) NOTE: Internal dissipation of 0.8 W is estimated for a 2-W system with 15-dB crest factor per channel. Tables 3 and 4 show that for some applications no airflow is required to keep junction temperatures in the specified range. The TPA0213 is designed with thermal protection that turns the device off when the junction temperature surpasses 150°C to prevent damage to the IC. Tables 3 and 4 were calculated for maximum listening volume without distortion. When the output level is reduced the numbers in the table change significantly. Also, using 8-Ω speakers dramatically increases the thermal performance by increasing amplifier efficiency. ST/MN (stereo/mono) operation The ability of the TPA0213 to easily switch between mono BTL and stereo SE modes is one of its most important cost saving features. This feature eliminates the requirement for an additional headphone amplifier in applications where an internal speaker is driven in BTL mode but external stereo headphone or speakers must be accommodated. When ST/MN is held high, the input mux selects the RIN and LIN inputs and the output is in stereo SE mode. When ST/MN is held low, the input mux selects the mono-in input and the output is in mono BTL mode. Control of the ST/MN input can be from a logic-level CMOS source or, more typically, from a switch-controlled resistor divider network as shown in Figure 17. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 17 TPA0213 2-W MONO AUDIO POWER AMPLIFIER WITH HEADPHONE DRIVE SLOS276C – JANUARY 2000 – REVISED APRIL 2001 APPLICATION INFORMATION ST/MN (stereo/mono) operation (continued) CB 4 VDD 3 BYPASS VDD GND Ci 50 kΩ RI 1.25*R 100 kΩ 1 Right Audio Input 5 Ci VDD BYPASS 50 kΩ Mono Audio Input 1 kΩ 8 MONO-IN RIN RI M U X – R – + CC RO/MO+ 6 + BYPASS BYPASS 100 kΩ 50 kΩ Stereo/Mono Control 50 kΩ ST/MN 7 LO/MO– 10 50 kΩ 1.25*R Left Audio Input Ci RI 9 M U X LIN – R – + CC + 1 kΩ BYPASS BYPASS From System Control 2 SHUTDOWN Shutdown and Depop Circuitry Figure 17. TPA0213 Resistor Divider Network Circuit Using a readily available 1/8-in. (3.5 mm) stereo headphone jack, the control switch is closed when no plug is inserted. When closed, the 100-kΩ/1-kΩ divider pulls the ST/MN input low. When a plug is inserted, the 1-kΩ resistor is disconnected and the ST/MN input is pulled high. The mono speaker is also physically disconnected from the RO/MO+ output so that no sound is heard from the speaker while the headphones are inserted. 18 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 TPA0213 2-W MONO AUDIO POWER AMPLIFIER WITH HEADPHONE DRIVE SLOS276C – JANUARY 2000 – REVISED APRIL 2001 MECHANICAL DATA DGQ (S-PDSO-G10) PowerPAD PLASTIC SMALL-OUTLINE PACKAGE 0,27 0,17 0,50 10 0,25 M 6 Thermal Pad (See Note D) 0,15 NOM 3,05 2,95 4,98 4,78 Gage Plane 0,25 1 0°– 6° 5 3,05 2,95 0,69 0,41 Seating Plane 1,07 MAX 0,15 0,05 0,10 4073273/A 04/98 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion. The package thermal performance may be enhanced by bonding the thermal pad to an external thermal plane. This pad is electrically and thermally connected to the backside of the die and possibly selected leads. The dimension of the thermal pad is 1.40 mm (height as illustrated) × 1.80 (width as illustrated) mm (maximum). The pad is centered on the bottom of the package. PowerPAD is a trademark of Texas Instruments. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 19 IMPORTANT NOTICE Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue any product or service without notice, and advise customers to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgment, including those pertaining to warranty, patent infringement, and limitation of liability. TI warrants performance of its products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed, except those mandated by government requirements. Customers are responsible for their applications using TI components. In order to minimize risks associated with the customer’s applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right of TI covering or relating to any combination, machine, or process in which such products or services might be or are used. TI’s publication of information regarding any third party’s products or services does not constitute TI’s approval, license, warranty or endorsement thereof. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations and notices. Representation or reproduction of this information with alteration voids all warranties provided for an associated TI product or service, is an unfair and deceptive business practice, and TI is not responsible nor liable for any such use. Resale of TI’s products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service, is an unfair and deceptive business practice, and TI is not responsible nor liable for any such use. Also see: Standard Terms and Conditions of Sale for Semiconductor Products. www.ti.com/sc/docs/stdterms.htm Mailing Address: Texas Instruments Post Office Box 655303 Dallas, Texas 75265 Copyright 2001, Texas Instruments Incorporated