150W U-Bracket Single Output with PFC Function ULP-150 series Features : Universal AC input / Full range(up to 295VAC) Built in active PFC compliance to EN61000-3-2 class C Constant Voltage design High efficiency up to 93% Protections: Short circuit / Overload / Over voltage / Over temperature Cooling by free air convection Half encapsulated U-bracket low profile:33mm ZVS technology to reduce power dissipation Suitable for built-in type LED applications 3 years warranty SPECIFICATION MODEL OUTPUT ULP-150-12 ULP-150-15 ULP-150-24 ULP-150-36 ULP-150-48 DC VOLTAGE 12V 15V 24V 36V 48V RATED CURRENT 12.5A 10A 6.3A 4.2A 3.2A CURRENT RANGE 0 ~ 12.5A 0 ~ 10A 0 ~ 6.3A 0 ~ 4.2A 0 ~ 3.2A 150W 150mVp-p 151.2W 150mVp-p 151.2W 250mVp-p 153.6W 250mVp-p 13.5~16.5V 21.6~26.4V 32.4~39.6V 43.2~52.8V RATED POWER 150W RIPPLE & NOISE (max.) Note.2 100mVp-p VOLTAGE ADJ. RANGE 11.0~13.2V VOLTAGE TOLERANCE Note.3 2.0% 2.0% 2.0% 2.0% 2.0% LINE REGULATION 0.5% 0.5% 0.5% 0.5% 0.5% 1.0% 1.0% 1.0% 1.0% LOAD REGULATION 1.0% 2000ms, 100ms/230VAC SETUP, RISE TIME HOLD UP TIME (Typ.) VOLTAGE RANGE 16ms/230VAC Note.4 90 ~ 295VAC FREQUENCY RANGE POWER FACTOR (Typ.) INPUT EFFICIENCY (Typ.) AC CURRENT (Typ.) INRUSH CURRENT (Typ.) LEAKAGE CURRENT OVERLOAD PROTECTION SHORT CIRCUIT OVER VOLTAGE OVER TEMPERATURE WORKING TEMP. WORKING HUMIDITY 47 ~ 63Hz PF 0.98/115VAC 3000ms, 100ms/115VAC at full load 16ms/115VAC at full load 127 ~ 417VDC PF>0.96/230VAC PF 0.94/277VAC at full load 91.5% 91.5% 2A/115VAC 1A/230VAC 0.7A/277VAC Cold start 65A/230VAC 93% 93% 93% <0.75mA / 277VAC 130~185% rated output power Protection type : Hiccup mode, recovers automatically after fault condition is removed Protection type : Hiccup mode, recovers automatically after fault condition is removed 17 ~ 21V 26.7 ~ 32.4V 41.4 ~ 48.6V 13.6 ~ 16.3V 53 ~ 64.8V Protection type : Shut down o/p voltage with auto-recovery or re-power on to recovery 95 5 (RTH2) Protection type : Shut down o/p voltage, recovers automatically after temperature goes down -30 ~ +70 (Refer to "Derating Curve") 20 ~ 90% RH non-condensing ENVIRONMENT STORAGE TEMP., HUMIDITY -40 ~ +85 , 10 ~ 95% RH 0.03%/ (0 ~ 60 TEMP. COEFFICIENT 10 ~ 500Hz, 5G 10min./1cycle, 60min. each along X, Y, Z axes VIBRATION SAFETY & EMC (Note 5) Design refer to EN61347-2-13,IEC61347-2-13,UL8750 SAFETY STANDARDS WITHSTAND VOLTAGE Note.6 I/P-O/P:3.75KVAC I/P-FG:1.88KVAC O/P-FG:0.5KVAC ISOLATION RESISTANCE EMC EMISSION EMC IMMUNITY OTHERS NOTE I/P-O/P, I/P-FG, O/P-FG:100M Ohms/500VDC/25 / 70%RH Compliance to EN55015, EN61000-3-2 Class C( 60% load),EN61000-3-3 Compliance to EN61000-4-2,3,4,5,6,8,11; EN61547, EN55024, light industry level (surge 4KV), criteria A MTBF 216.3K hrs min. DIMENSION PACKING 215*67.4*33mm (L*W*H) 0.67kg; 24PCS/17.5kg/0.65CUFT MIL-HDBK-217F (25 ) 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. Derating may be needed under low input voltages. Please check the static characteristics for more details. 5. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. 6. Please remove the component D1 before conducted Hipot test. File Name:ULP-150-SPEC 2011-08-11 ULP-150 150W U-Bracket Single Output with PFC Function Mechanical Specification Case No. 988 series Unit:mm 7.5 6.5 4.5 4PL 3.5 194 208 3.5 215 33 3 3 67.4 6.2 2 2 7.62 52 62.7 1 1 7.62 6.2 211 201 4 3.5 4PL DC Terminal pin NO. Assignment AC Terminal pin NO. Assignment Pin No. 1 2 3 Assignment FG AC/L AC/N Pin No. 1 2 3 4 Terminal DECA T31-C032033702 Assignment VVV+ V+ Terminal DECA T31-C032043702 Block Diagram EMI FILTER I/P BRIDGE RECTIFIERS APFC CONTROLLER POWER SWITCHING SYNCHRONOUS RECTIFIERS & FILTER +V -V O.T.P. FG O.L.P. Derating Curve DETECTION CIRCUIT PWM CONVERTER O.V.P. Static Characteristics 100 130 Mount with a 300*500*2mm heatsink 90 100 80 100VAC 60 70 230VAC LOAD(%) LOAD (%) 80 40 20 -30 60 50 40 0 10 20 30 40 45 50 55 60 65 AMBIENT TEMPERATURE ( ) 70 (HORIZONTAL) 90 100 110 135 155 230 295 INPUT VOLTAGE (V) 60Hz File Name:ULP-150-SPEC 2011-08-11