MIMIX XF1000-DB

DC-5.0 GHz
34.0 dBm Packaged HFET
F1000-DB
May 2010 - Rev 25-May-10
Features
High Linearity, 47 dBm OIP3
High Gain, 10 dB Gain @ 4.9 GHz
34 dBm P1dB
Low Thermal Resistance
Surface Mount 3x6mm DFN
General Description
The XF1000-BD is a high linearity Hetrojunction Field Effect
Transistor (HFET) housed in a 3x6mm DFN package.
Optimum performance is achieved when the device is
biased at a drain voltage of 8V and drain current of 600 mA.
At this bias point and at 4.9 GHz the device is capable of
more than 34 dBm of P1dB and OIP3 of more than 46 dBm.
The XF1000-DB is suitable for applications up to 5 GHz
where it has 10 dB of gain.
Typical Performance: 8V, 25 ºC
Parameter
Typical
Frequency (F)
3600
Gain (S21)
10.5
Ourput IP3 (OIP3)
47.0
Output P1dB
34.0
Quiescent Current (Idq)
600
Input Return Loss (S11)
-6.3
Output Return Loss (S22) -12.6
4900
10.0
46.0
33.7
600
-8.0
-11.5
Units
MHz
dB
dBm
dBm
mA
dB
dB
Absolute Maximum Ratings
Device Voltage (Vdd)
Current (Idd)
Power Dissipation (PDC)
RF Input Power (RFin)
Junction Temperature
Thermal Resistance
Storage Temperature (Tstg)
Operating Temperature
ESD (HBM)
Moisture Sensitivity Level (MSL)
+9.0 V
750 mA
6.0W
+25 dBm
175 ºC
18 ºC/W
-55 ºC to +150 ºC
-40 ºC to +85 ºC
Class 1A
MSL 3
Operation of this device beyond any of these parameters may cause
permanent damage.
Electrical Characteristics (T=25ºC,Vdd=8V)
Unless otherwise specified, the following specifications are guaranteed at room temperature in a Mimix test fixture.
Parameter
Condition
Frequency Range (F)
Test Frequency
Small Signal Gain (S21)
Externally matched
Output Intercept Point (OIP3) Pout/Tone=22 dBm, Spacing=5 MHz
Output P1dB
Quiescent Current (Icq)
Noise Figure (NF)
Units Min
Typ
Max
MHz DC
5000
MHz
2000
12.5 14.5
dB
dBm +44.0 +46.5
dBm +33.0 +34.0
mA
600.0 700.0
dB
5
Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099
Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com
Page 1 of 9
Characteristic Data and Specifications are subject to change without notice. ©2010 Mimix Broadband, Inc.
Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept
their obligation to be compliant with U.S. Export Laws.
DC-5.0 GHz
34.0 dBm Packaged HFET
F1000-DB
May 2010 - Rev 25-May-10
S-parameters: (Vdd=8V, Idd=600 mA)
S12
-38
dB
-40
-42
2.5
3
3.5
Frequency (GHz)
4
4.5
5
5.5
6
0
0.5
1
1.5
2
2.5
3
3.5
Frequency (GHz)
S11
2.
0
1.0
0.8
6
0.
0
4.
5.0
2.4 GHz
0.5 GHz
0.8
0.6
0.2
0.9 GHz
10.0
10.0
2.0 GHz
0
10.0
5.0
3.0
4.0
2.0
1.0
0.8
0.6
-10.0
-5.
0.5 GHz
0
3.
0.4
1.0
0.8
6
0.
2.
0
5.0
10.0
0.4
Swp Max
6GHz
3.5 GHz
.0
2.0 GHz
0 1 GHz
0.1
2
-0.
0
-4
.0
-3
.0
-1.0
-0.8
-0
Swp Min
0.1GHz
.
-2
-0
.6
.6
0.1 GHz
.0
-2
0
.4
-0
-0.8
0.2
0.2
6
-4
.0
-5.
0
4
.4
-0
6.0 GHz
0.2
0.
4
0
5.5
0.
4
0
3.
1.6 GHz
2
5
-3
.0
6 0 GH
6.0
GHz
2.4 GHz
-0.
4.5
S22
Swp Max
6GHz
3.5 GHz
0.9 GHz
4
5.0
2
3.0
1.5
4.0
1
2.0
0.5
DB(GMax())
1.0
0
DB(|S(2,1)|)
-1.0
dB
-36
S21
32
30
28
26
24
22
20
18
16
14
12
10
8
6
4
2
0
-10.0
-34
Swp Min
0.1GHz
S-Parameters files are available for download at www.mimixbroadband.com.
Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099
Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com
Page 2 of 9
Characteristic Data and Specifications are subject to change without notice. ©2010 Mimix Broadband, Inc.
Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept
their obligation to be compliant with U.S. Export Laws.
DC-5.0 GHz
34.0 dBm Packaged HFET
F1000-DB
May 2010 - Rev 25-May-10
Evaluation Board: (3.6 GHz)
Vgg GND Vdd
RF in
RF out
Recommended Schematic
C7
C8
C10
R1
C1
TL1
C2
C9
TL3
C4
TL2
C3
C6
C5
Component Values
REF. Designator
R1
DESCRIPTION
QTY
TYP
RESISTOR, 100Ohm 0402
1
100 Ω
C1
0 ohm link
1
0Ω
C2
CAPACITOR, 2.2pF 0402
1
2.2pF
TOLERANCE
0.05pF
C3
CAPACITOR, 4.0pF 0402
1
4.0pF
0.05pF
C4
CAPACITOR, 2.2pF 0402
1
2.2pF
0.05pF
C5
CAPACITOR, 1.6pF 0402
1
1.6pF
0.05pF
C6
CAPACITOR, 20pF 0402
1
20pF
C7, 9
CAPCITOR, 1uF 0603
1
1uF
C8, C10
CAPACITOR, 10nF 0402
1
10nF
Ref Designator
Electrical Length
TL1
50Ω, 20.8°
TL2
50Ω, 9.3°
TL3
50Ω, 77°
Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099
Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com
Page 3 of 9
Characteristic Data and Specifications are subject to change without notice. ©2010 Mimix Broadband, Inc.
Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept
their obligation to be compliant with U.S. Export Laws.
DC-5.0 GHz
34.0 dBm Packaged HFET
F1000-DB
May 2010 - Rev 25-May-10
Typical Performance: 3.6 GHz (Evaluation Board)
XF1000-DB: 3.6 GHz Evaluation Board, S-parameters
15
10
5
NF (dB
B)
(dB)
0
-5
-10
S11
-15
S21
S22
-20
-25
3.2
3.3
3.4
3.5
3.6
3.7
3.8
3.9
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
4
XF1000-DB: 3.6 GHz Evaluation Board, NF vs. Frequency
Id=400mA
Id=500mA
Id=600mA
3000
3200
3400
Frequency (GHz)
3800
4000
Frequency (MHz)
XF1000-DB: 3.6 GHz Evaluation Board, P1dB vs. Frequency
XF1000-DB: 3.6 GHz Evaluation Board, EVM vs. Pout vs. Frequency
7
35
6.5
34.5
6
34
5.5
FREQ=3.3
33.5
5
FREQ=3.4
33
4.5
FREQ=3.5
4
FREQ=3 6
FREQ=3.6
3.5
FREQ=3.7
EVM (%))
P1dB (dBm)
P
3600
32.5
32
25C
31.5
FREQ=3.9
2.5
85C
31
FREQ=3.8
3
2
-40C
1.5
30.5
1
30
3.2
3.3
3.4
3.5
3.6
3.7
3.8
3.9
0.5
4
0
(GHz))
F
Frequency
(GH
20
21
22
23
24
25
26
27
28
Pout (dBm)
XF1000-DB: 3.6 GHz Evaluation BoardOIP3 vs. Pout, 25°C
50
49
49
48
48
47
47
46
46
OIP3(dBm))
OIP3(dBm))
50
45
Freq(GHz)=3.3
Freq(GHz)=3.4
Freq(GHz)=3.5
Freq(GHz)=3.6
Freq(GHz)=3.7
Freq(GHz)=3.8
Freq(GHz)=3.9
44
43
42
41
40
39
XF1000-DB: 3.6 GHz Evaluation Board, OIP3 vs. Pout, 85°C
45
44
Freq(GHz)=3.3
Freq(GHz)=3.4
Freq(GHz)=3.5
Freq(GHz)=3.6
Freq(GHz)=3.7
Freq(GHz)=3.8
Freq(GHz)=3.9
43
42
41
40
39
38
38
22
23
24
25
26
27
28
Pout(dBm)
29
30
31
32
33
22
23
24
25
26
27
28
29
30
31
32
33
Pout(dBm)
Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099
Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com
Page 4 of 9
Characteristic Data and Specifications are subject to change without notice. ©2010 Mimix Broadband, Inc.
Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept
their obligation to be compliant with U.S. Export Laws.
DC-5.0 GHz
34.0 dBm Packaged HFET
F1000-DB
May 2010 - Rev 25-May-10
Typical Performance: 3.6 GHz (Evaluation Board) (cont.)
XF1000-DB: 3.6 GHz Evaluation Board, OIP3 vs. Pout, -40 ºC
50
49
48
OIP3(dB
Bm)
47
46
45
Freq(GHz)=3.3
Freq(GHz)=3.4
Freq(GHz)=3.5
Freq(GHz)=3.6
Freq(GHz)=3.7
Freq(GHz)=3.8
Freq(GHz)=3.9
44
43
42
41
40
39
38
22
23
24
25
26
27
28
29
30
31
32
33
Pout(dBm)
Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099
Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com
Page 5 of 9
Characteristic Data and Specifications are subject to change without notice. ©2010 Mimix Broadband, Inc.
Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept
their obligation to be compliant with U.S. Export Laws.
DC-5.0 GHz
34.0 dBm Packaged HFET
F1000-DB
May 2010 - Rev 25-May-10
Evaluation Board: (4.9 GHz)
Vgg GND Vdd
R F in
R F o ut
Recommended Schematic
C6
C5
C8
C7
R1
TL3
C1
TL1
TL2
C2
C4
C3
Component Values
REF. Designator
g
R1
DESCRIPTION
QTY
TYP
Resistor, 100Ohm 0402
1
100 Ω
Tolerance
C1
CAPACITOR, 0402, 50V
1
20pF
5%
C2
CAPACITOR, 0402, 50V
1
1.3pF
0.05pF
C3
CAPACITOR, 0402, ,50V
1
1.4pF
0.05pF
C4
CAPACITOR, 0402, 50V
1
20pF
5%
C5, C7
CAPACITOR, 0603, 16V
1
1uF
10%
C6, C8
CAPACITOR, 0402, 25V
1
10nF
10%
Ref Designator
g
Electrical Length
g
TL1
50Ω, (not critical)
TL2
50Ω, (not critical)
TL3
50Ω, 66°
Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099
Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com
Page 6 of 9
Characteristic Data and Specifications are subject to change without notice. ©2010 Mimix Broadband, Inc.
Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept
their obligation to be compliant with U.S. Export Laws.
DC-5.0 GHz
34.0 dBm Packaged HFET
F1000-DB
May 2010 - Rev 25-May-10
Typical Performance: 4.9 GHz (Evaluation Board)
XF1000-DB: 4.9 GHz Evaluation Boad, P1dB vs. Frequency
XF1000-DB: 4.9 GHz Evaluation Board, S-parameters
35
15
10
34.5
P1dB (dBm)
5
(dB)
0
-5
S11
S21
-10
34
33.5
33
S22
32.5
-15
-20
20
32
4.5
4.6
4.7
4.8
4.9
5
5.1
5.2
5.3
4.5
4.6
4.7
4.8
Frequency (GHz)
4.9
5
5.1
5.2
5.3
Frequency (GHz)
XF1000-DB: 4.9 GHz Evaluation Board OIP3 vs. Pout
XF1000-DB: 4.9 GHz Evaluation Board, Gain vs. Pout
48
11
47
46
10
45
Freq(GHz)=4.6
Freq(GHz)=4.7
8
7
Freq(GHz)=4.8
OIP3(dBm)
Gain (dB)
44
9
43
Freq(GHz)=4.6
42
Freq(GHz)=4.7
41
Freq(GHz)=4.8
Freq(GHz)=4.9
40
Freq(GHz)=4.9
Freq(GHz)=5 .0
39
Freq(GHz)=5.0
Freq(GHz)=5.1
38
Freq(GHz)=5.1
37
6
18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36
Pout (dBm)
36
20
21
22
23
24
25
26
27
28
29
30
Pout(dBm)
Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099
Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com
Page 7 of 9
Characteristic Data and Specifications are subject to change without notice. ©2010 Mimix Broadband, Inc.
Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept
their obligation to be compliant with U.S. Export Laws.
DC-5.0 GHz
34.0 dBm Packaged HFET
F1000-DB
May 2010 - Rev 25-May-10
App Note [1] Biasing - The XF1000-DB requires power supply sequencing. Negative voltage supply (Vgg) needs to be turned on first and then
positive voltage can be applied to the drain (Vdd). When turning off the device, the positive supply (Vdd) should be turned off first and then
negative voltage (Vgg) can be removed.
The gate voltage is adjusted in order to set the drain current to the desired level. The gate voltage required to achieve a certain current can vary
over temperature and from one device to another due to pinch-off voltage variation. Constant drain current can be achieved by Implementing an
active bias circuit which allows for temperature compensation and eliminates the effect of pinch off voltage variation.
Physical Dimensions
Pin-out Details
Description
Pin #
gg
Vgg
7
RF Input
3,4,5
RF Output /Vdd
10,11,12
NC
1,2,6,8,9,13,14
Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099
Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com
Page 8 of 9
Characteristic Data and Specifications are subject to change without notice. ©2010 Mimix Broadband, Inc.
Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept
their obligation to be compliant with U.S. Export Laws.
DC-5.0 GHz
34.0 dBm Packaged HFET
F1000-DB
May 2010 - Rev 25-May-10
Handling and Assembly Information
CAUTION! - Mimix Broadband MMIC Products contain gallium arsenide (GaAs) which can be hazardous to the human
body and the environment. For safety, observe the following procedures:
Do not ingest.
Do not alter the form of this product into a gas, powder, or liquid through burning, crushing, or chemical
processing as these by-products are dangerous to the human body if inhaled, ingested, or swallowed.
Observe government laws and company regulations when discarding this product. This product must be
discarded in accordance with methods specified by applicable hazardous waste procedures.
Life Support Policy - Mimix Broadband's products are not authorized for use as critical components in life support
devices or systems without the express written approval of the President and General Counsel of Mimix Broadband. As
used herein: (1) Life support devices or systems are devices or systems which, (a) are intended for surgical implant into
the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions
for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. (2) A critical
component is any component of a life support device or system whose failure to perform can be reasonably expected
to cause the failure of the life support device or system, or to affect its safety or effectiveness.
Package Attachment - This packaged product from Mimix Broadband is provided as a rugged surface mount package
compatible with high volume solder installation. Care should be taken not to apply heavy pressure to the top or base
material to avoid package damage. Vacuum tools or other suitable pick and place equipment may be used to pick and
place this part. Care should be taken to ensure that there are no voids or gaps in the solder connection so that good RF,
DC and ground connections are maintained. Voids or gaps can eventually lead not only to RF performance degradation,
but reduced reliability and life of the product due to thermal stress.
Mimix Lead-Free RoHS Compliant Program - Mimix has an active program in place to meet customer and governmental
requirements for eliminating lead (Pb) and other environmentally hazardous materials from our products. All Mimix
RoHS compliant components are form, fit and functional replacements for their non-RoHS equivalents. Lead plating of
our RoHS compliant parts is 100% matte tin (Sn) over copper alloy and is backwards compatible with current standard
SnPb low-temperature reflow processes as well as higher temperature (260°C reflow) “Pb Free” processes.
Ordering Information
Part Number for Ordering
XF1000-DB-0G00
XF1000-DB-0G0T
XF1000-DB-EV1
XF1000-DB-EV2
Description
Matte Tin plated RoHS compliant 3x6mm surface mount package in bulk quantity
Matte Tin plated RoHS compliant 3x6mm surface mount package in tape and reel
Evaluation Board @ 3600 MHz
Evaluation Board @ 4900 MHz
C a u t i o n : E S D S e n s i t i ve
Appropriate precautions in handling, packaging
and testing devices must be observed.
Proper ESD procedures should be followed when handling this device.
Mimix Broadband, Inc., 10795 Rockley Rd., Houston, Texas 77099
Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com
Page 9 of 9
Characteristic Data and Specifications are subject to change without notice. ©2010 Mimix Broadband, Inc.
Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept
their obligation to be compliant with U.S. Export Laws.