TI TPS71936

TPS718xx
TPS719xx
www.ti.com..................................................................................................................................................... SBVS088C – FEBRUARY 2007 – REVISED MAY 2008
Dual, 200mA Output, Low Noise, High PSRR
Low-Dropout Linear Regulators
FEATURES
DESCRIPTION
• Dual, 200mA High-Performance LDOs
• Low Total Quiescent Current: 90µA with Both
LDOs Enabled
• Low Noise: 70µVRMS/V
• Active Output Pulldown (TPS719xx)
• Independent Enables for Each LDO
• PSRR: 65dB at 1kHz, 45dB at 1MHz
• Available in Multiple Fixed-Output Voltage
Combinations from 0.9V to 3.6V Using
Innovative Factory EEPROM Programming
• Fast Start-Up Time: 160µs
• Over-Current, Over-Temperature and
Under-Voltage Protection
• Low Dropout: 230mV at 200mA
• Stable with 1µF Ceramic Output Capacitor
• Available in 2mm × 2mm SON-6 and 6-Ball
WCSP Packages
The TPS718xx and TPS719xx families of low-dropout
(LDO) regulators offer a high power-supply rejection
ratio (PSRR), low noise, fast start-up, and excellent
line and load transient responses while consuming a
very low 90µA (typical) at no load ground current with
both LDOs enabled. The TPS719xx also provides an
active pulldown circuit to quickly discharge output
loads. The TPS718xx and TPS719xx are stable with
ceramic capacitors and use an advanced BiCMOS
fabrication process to yield a typical dropout voltage
of 230mV at 200mA output loads. The TPS718xx and
TPS719xx also use a precision voltage reference and
feedback loop to achieve 3% overall accuracy over all
load, line, process, and temperature variations. Both
families of devices are fully specified from TJ = –40°C
to +125°C and are offered in 2mm × 2mm SON-6 and
6-ball Wafer Chip-Scale (WCSP) packages that are
ideal for applications such as mobile handsets and
WLAN that require good thermal dissipation while
maintaining a very small footprint.
1
23
APPLICATIONS
•
•
•
•
Digital Cameras and Camera Modules
Cellular Camera and TV Phones
Wireless LAN, Bluetooth®
Handheld Products
2.7V to 6.5V
VIN
0.9V to 3.6V
IN
1 mF
On
VOUT
OUT1
1m F
TPS718xx
TPS719xx
6 EN1
0.9V - 3.6V
VOUT
OUT2
On
TPS718xx, TPS719xx
YZC Package
6-BALL WCSP
(Top View)
C2
OUT1 1
EN1
Off
Off
TPS718xx, TPS719xx
DRV Package
2mm x 2mm SON-6
(Top View)
IN 2
GND
5 GND
OUT2 3
EN2
GND
C1
EN1
OUT1
B2
B1
A2
A1
GND
1m F
4 EN2
EN2
TPS718Axx, TPS719Axx
YZC Package
6-BALL WCSP
(Top View)
IN
OUT2
A1
A2
B1
B2
C1
C2
EN1
OUT1
GND
IN
EN2
OUT2
Typical Application Circuit
1
2
3
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Bluetooth is a registered trademark of Bluetooth SIG, Inc.
All other trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2007–2008, Texas Instruments Incorporated
TPS718xx
TPS719xx
SBVS088C – FEBRUARY 2007 – REVISED MAY 2008..................................................................................................................................................... www.ti.com
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
ORDERING INFORMATION (1)
VOUT (2) (3)
PRODUCT
TPS718xx-yywwwz
TPS718Axx-yywwwz
TPS719xx-yywwwz
TPS719Axx-yywwwz
A denotes device with rotated pin 1 orientation of wafer-chipscale package.
XX is nominal output voltage for LDO1 (for example, 28 = 2.8V).
YY is nominal output voltage for LDO2.
WWW is package designator.
Z is tape and reel quantity (R = 3000, T = 250).
Examples: TPS71918–285DRVR
TPS719185-33DRVR
(1)
(2)
(3)
XX = 18 = 1.8V, YYY = 285 = 2.85V
XXX = 185 = 1.85V, YY = 33 = 3.3V
DRV = 2mm x 2mm SON package
Z = R = 3000 piece reel
For the most current package and ordering information see the Package Option Addendum at the end of this document, or see the TI
website at www.ti.com.
Both outputs are programmable from 0.9V to 3.6V in 50mV increments.
Output voltages from 0.9V to 3.6V in 50mV increments are available through the use of innovative factory EEPROM programming;
minimum order quantities may apply. Contact factory for details and availability.
ABSOLUTE MAXIMUM RATINGS (1)
Over operating temperature range (unless otherwise noted). All voltages are with respect to GND.
PARAMETER
TPS718xx, TPS719xx
UNIT
Input voltage range, VIN
Enable voltage range, VEN1 and VEN2
Output voltage range, VOUT
–0.3 to +7.0
V
–0.3 to VIN + 0.3V
V
–0.3 to +7.0
V
Peak output current
Internally limited
Output short-circuit duration
Indefinite
Junction temperature range, TJ
–55 to +150
°C
Storage temperature range , TSTG
–55 to +150
°C
Total continuous power dissipation, PDISS
See Dissipation Ratings Table
ESD rating, HBM
2
kV
ESD rating, CDM
500
V
(1)
Stresses above these ratings may cause permanent damage. Exposure to absolute maximum conditions for extended periods may
degrade device reliability. These are stress ratings only, and functional operation of the device at these or any other conditions beyond
those specified is not implied.
DISSIPATION RATINGS
BOARD
PACKAGE
RθJC
RθJA
DERATING FACTOR
ABOVE TA = +25°C
TA < +25°C
TA = +70°C
TA = +85°C
High-K (1)
DRV
20°C/W
95°C/W
10.53mW/°C
1053mW
579mW
421mW
High-K (1)
YZC
27°C/W
190°C/W
5.3mW/°C
530mW
295mW
215mW
(1)
2
The JEDEC high-K (2s2p) board used to derive this data was a 3in × 3in, multilayer board with 1-ounce internal power and ground
planes and 2-ounce copper traces on top and bottom of the board.
Submit Documentation Feedback
Copyright © 2007–2008, Texas Instruments Incorporated
Product Folder Link(s): TPS718xx TPS719xx
TPS718xx
TPS719xx
www.ti.com..................................................................................................................................................... SBVS088C – FEBRUARY 2007 – REVISED MAY 2008
ELECTRICAL CHARACTERISTICS
Over operating temperature range (TJ = –40°C to +125°C), VIN = VOUT(TYP) + 0.5V or 2.7V, whichever is greater;
IOUT = 0.5mA, VEN1 = VEN2 = VIN, COUT = 1.0µF, unless otherwise noted. Typical values are at TJ = +25°C.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
VIN
Input voltage range (1)
2.7
6.5
VOUT1, VOUT2
Output voltage range
0.9
3.6
Nominal
TJ = +25°C
VOUT1, VOUT2
Output accuracy
ΔVOUT/ ΔVIN
Line regulation
VOUT(NOM) + 0.5V ≤ VIN ≤ 6.5V,
IOUT = 5mA
ΔVOUT/ ΔIOUT
Load regulation
0mA ≤ IOUT ≤ 200mA
VDO
Dropout voltage (2)
(VIN = VOUT(NOM) – 0.1V)
IOUT = 200mA
ICL
Output current limit (per output)
VOUT = 0.9 × VOUT(NOM)
IGND
ISHDN
PSRR
VN
Ground pin current
Shutdown current (IGND)
Power-supply rejection ratio
VIN = 3.8V, VOUT = 2.8V,
IOUT = 200mA
–3.0
240
V
V
mV
+3.0
%
130
µV/V
75
µV/mA
230
400
mV
340
575
mA
IOUT1 = IOUT2 = 0.1mA
90
160
µA
IOUT1 = IOUT2 = 200mA
250
VEN1,2 ≤ 0.4V, 2.7V ≤ VIN < 4.5V,
TJ = –40°C to +85°C
0.3
VEN1,2 ≤ 0.4V, 4.5V ≤ VIN ≤ 6.5V,
TJ = –40°C to +85°C
1.8
µA
f = 100Hz
63
dB
f = 1kHz
63
dB
f = 10kHz
72
dB
f = 100kHz
58
dB
f = 1MHz
44
dB
Output noise voltage
BW = 100Hz to 100kHz
µA
3.0
70 × VOUT
µA
µVRMS
TSTR
Startup time (3)
RL = 14Ω, VOUT = 2.8V,
COUT = 1.0µF
160
µs
TSHUT
Shutdown time (4), (5)
(TPS719xx only)
RL = ∞, COUT = 1.0µF,
VOUT = 2.8V
180
µs
VEN(HI)
Enable high (enabled)
(EN1 and EN2)
VIN ≤ 5.5V
VEN(LO)
Enable low (shutdown)
(EN1 and EN2)
IEN
UVLO
(1)
(2)
(3)
(4)
(5)
Over VIN, IOUT, VOUT + 0.5V ≤ VIN ≤ 6.5V
Temp
0mA ≤ IOUT ≤ 200mA
±2.5
UNIT
5.5V < VIN ≤ 6.5V
Enable pin current, enabled
(EN1 and EN2)
EN1 = EN2 = 6.5V
Undervoltage lockout
VIN rising
Hysteresis
VIN falling
TSD
Thermal shutdown temperature
TJ
Operating junction temperature
1.2
6.5
V
1.25
6.5
V
0
0.4
V
0.04
1.0
µA
2.45
2.52
2.38
V
150
mV
Shutdown, temperature increasing
+160
°C
Reset, temperature decreasing
+140
°C
–40
+125
°C
Minimum VIN = VOUT + VDO or 2.7V, whichever is greater.
VDO is not measured for devices with VOUT(NOM) < 2.8V because minimum VIN = 2.7V.
Time from VEN = 1.25V to VOUT = 95% (VOUT(NOM)).
Time from VEN = 0.4V to VOUT = 5% (VOUT(NOM)).
See Shutdown section in the Applications Information for more details.
Copyright © 2007–2008, Texas Instruments Incorporated
Product Folder Link(s): TPS718xx TPS719xx
Submit Documentation Feedback
3
TPS718xx
TPS719xx
SBVS088C – FEBRUARY 2007 – REVISED MAY 2008..................................................................................................................................................... www.ti.com
DEVICE INFORMATION
TPS719 only
60W
Bandgap
UVLO
Thermal
Shutdown
Current
Limit
2.5mA
OUT1
EN1
Enable and
Power
Control
Logic
EN2
OUT2
Thermal
Shutdown
IN
2.5mA
Current
Limit
UVLO
Bandgap
60W
TPS719 only
GND
Figure 1. Functional Block Diagram
4
Submit Documentation Feedback
Copyright © 2007–2008, Texas Instruments Incorporated
Product Folder Link(s): TPS718xx TPS719xx
TPS718xx
TPS719xx
www.ti.com..................................................................................................................................................... SBVS088C – FEBRUARY 2007 – REVISED MAY 2008
DRV PACKAGE
SON-6
(TOP VIEW)
OUT1 1
6 EN1
IN 2
GND
OUT2 3
5 GND
4 EN2
YZC PACKAGE
6-BALL WCSP
(TOP VIEW)
C2
C1
B2
B1
A2
A1
EN1
OUT1
GND
IN
EN2
OUT2
TPS718xx
TPS719xx
YZC PACKAGE
6-BALL WCSP
(TOP VIEW)
A1
A2
B1
B2
C1
C2
EN1
OUT1
GND
IN
EN2
OUT2
TPS718Axx
TPS719Axx
PIN DESCRIPTIONS
TPS718Axx (1)
TPS719Axx (1)
TPS718xx
TPS719xx
(1)
NAME
DRV
YZC
YZC
DESCRIPTION
OUT1
1
C1
A2
Output of Regulator 1. A small ceramic capacitor (typically ≥ 1µF) is
needed from this pin to ground to assure stability.
IN
2
B1
B2
Input supply to both regulators.
OUT2
3
A1
C2
Output of Regulator 2. A small ceramic capacitor (typically ≥ 1µF) is
needed from this pin to ground to assure stability.
EN2
4
A2
C1
Enable pin for Regulator 2. Driving the Enable pin (EN2) high turns on
Regulator 2. Driving this pin low puts Regulator 2 into shutdown mode,
reducing operating current.
GND
5
B2
B1
Ground. DRV thermal pad should also be connected to ground.
EN1
6
C2
A1
Enable pin for Regulator 1. Driving the Enable pin (EN1) high turns on
Regulator 1. Driving this pin low puts Regulator 1 into shutdown mode,
reducing operating current.
A option denotes devices with rotated Pin 1 orientation on Wafer Chipscale packages.
Copyright © 2007–2008, Texas Instruments Incorporated
Product Folder Link(s): TPS718xx TPS719xx
Submit Documentation Feedback
5
TPS718xx
TPS719xx
SBVS088C – FEBRUARY 2007 – REVISED MAY 2008..................................................................................................................................................... www.ti.com
TYPICAL CHARACTERISTICS
Over operating temperature range (TJ = –40°C to +125°C), VIN = VOUT(TYP) + 0.5V or 2.7V, whichever is greater;
IOUT = 0.5mA, VEN1 = VEN2 = VIN, COUT = 1.0µF, unless otherwise noted. Typical values are at TJ = +25°C.
LINE REGULATION
LINE REGULATION
4
0
TJ = +85°C
IOUT = 5mA
3
-1
TJ = +125°C
TJ = +25°C
DVOUT (mV)
2
DVOUT (mV)
IOUT = 200mA
1
TJ = +25°C
0
-1
TJ = -40°C
-2
-3
TJ = +85°C
-2
TJ = -40°C
-4
TJ = +125°C
-3
-5
-4
2.5
3.5
4.5
VIN (V)
5.5
6.5
2.5
3.5
Figure 2.
4.5
VIN (V)
5.5
6.5
150
200
Figure 3.
LOAD REGULATION UNDER LIGHT LOADS
LOAD REGULATION
4
5
TJ = +85°C
TJ = +25°C
2
0
-5
-2
DVOUT (mV)
DVOUT (mV)
0
TJ = -40°C
-4
-10
-15
-20
-25
-6
TJ = +125°C
TJ = +85°C
TJ = +25°C
TJ = -40°C
-30
TJ = +125°C
-8
-35
-40
-10
0
1
3
2
4
5
0
50
IOUT (mA)
100
IOUT (mA)
Figure 4.
Figure 5.
OUTPUT VOLTAGE vs
TEMPERATURE
DROPOUT VOLTAGE vs
OUTPUT CURRENT
2.805
350
IOUT = 5mA
TJ = +125°C
2.800
300
TJ = +85°C
2.795
2.785
IOUT = 200mA
2.780
2.775
VDO (mV)
IOUT = 0.1mA
2.790
VOUT (V)
250
200
150
TJ = +25°C
100
TJ = -40°C
2.770
50
2.765
0
2.760
-40 -25 -10
5
20
35 50
TJ (°C)
65
80
95 110 125
50
0
Figure 6.
6
Submit Documentation Feedback
100
IOUT (mA)
150
200
Figure 7.
Copyright © 2007–2008, Texas Instruments Incorporated
Product Folder Link(s): TPS718xx TPS719xx
TPS718xx
TPS719xx
www.ti.com..................................................................................................................................................... SBVS088C – FEBRUARY 2007 – REVISED MAY 2008
TYPICAL CHARACTERISTICS (continued)
Over operating temperature range (TJ = –40°C to +125°C), VIN = VOUT(TYP) + 0.5V or 2.7V, whichever is greater;
IOUT = 0.5mA, VEN1 = VEN2 = VIN, COUT = 1.0µF, unless otherwise noted. Typical values are at TJ = +25°C.
GROUND PIN CURRENT vs
OUTPUT CURRENT
200
GROUND PIN CURRENT vs
INPUT VOLTAGE
60
TJ = +125°C
IOUT = 1mA
TJ = +25°C
50
160
40
IGND (mA)
IGND (mA)
TJ = +85°C
120
TJ = -40°C
80
30
20
40
10
0
0
50
0
150
100
IOUT (mA)
200
2.5
5.5
Figure 9.
GROUND PIN CURRENT vs
TEMPERATURE (BOTH LDOs ENABLED)
SHUTDOWN CURRENT vs
INPUT VOLTAGE
6.5
5.0
IOUT = 0mA
4.5
Shutdown Current (mA)
120
100
IGND (mA)
4.5
VIN (V)
Figure 8.
140
80
60
40
20
4.0
TJ = +125°C
3.5
3.0
TJ = -40°C
2.5
TJ = +85°C
2.0
1.5
1.0
TJ = +25°C
0.5
0
0
-40 -25 -10
5
20
35 50
TJ (°C)
65
80
95 110 125
2.5
3.5
4.5
VIN (V)
5.5
6.5
Figure 10.
Figure 11.
CURRENT LIMIT vs
INPUT VOLTAGE
POWER-SUPPLY RIPPLE REJECTION vs
FREQUENCY (VIN – VOUT = 0.5V)
450
90
425
80
100mA
5mA
70
400
375
PSRR (dB)
Current Limit (mA)
3.5
350
325
275
50
200mA
40
30
TJ = +125°C
TJ = +85°C
TJ = +25°C
TJ = -40°C
300
60
20
10
0
250
2.5
3.5
4.5
VIN (V)
5.5
6.5
10
100
Figure 12.
1k
100k
10k
Frequency (Hz)
1M
10M
Figure 13.
Copyright © 2007–2008, Texas Instruments Incorporated
Product Folder Link(s): TPS718xx TPS719xx
Submit Documentation Feedback
7
TPS718xx
TPS719xx
SBVS088C – FEBRUARY 2007 – REVISED MAY 2008..................................................................................................................................................... www.ti.com
TYPICAL CHARACTERISTICS (continued)
Over operating temperature range (TJ = –40°C to +125°C), VIN = VOUT(TYP) + 0.5V or 2.7V, whichever is greater;
IOUT = 0.5mA, VEN1 = VEN2 = VIN, COUT = 1.0µF, unless otherwise noted. Typical values are at TJ = +25°C.
POWER-SUPPLY RIPPLE REJECTION vs
FREQUENCY (VIN – VOUT = 1V)
POWER-SUPPLY RIPPLE REJECTION vs
INPUT VOLTAGE
80
90
100mA
80
70
5mA
60
50
40
30
50
100kHz
40
1MHz
30
200mA
VOUT = 2.80V
IOUT = 5mA
10
10
0
0
10
100
1k
100k
10k
Frequency (Hz)
10M
1M
3.0
3.2
3.4
3.6
3.8
Figure 14.
Figure 15.
POWER-SUPPLY RIPPLE REJECTION vs
INPUT VOLTAGE
OUTPUT SPECTRAL NOISE DENSITY vs
FREQUENCY
Output Spectral Noise Density (mVÖHz)
10kHz
70
1kHz
60
100kHz
50
40
1MHz
30
20
VOUT = 2.80V
IOUT = 200mA
10
4.0
VIN (V)
80
PSRR (dB)
10kHz
20
20
0
10
VOUT = 2.80V
1
0.1
0.01
3.0
3.2
3.4
3.6
3.8
100
4.0
10k
1k
VIN (V)
Frequency (Hz)
Figure 16.
Figure 17.
LINE TRANSIENT RESPONSE
LOAD TRANSIENT RESPONSE
6.5V
1V/div 3.3V
IOUTmin = 3mA
dVIN
= 1V/ms
dt
100k
dIOUT
= 200mA/ms
dt
250mA/div
IOUT1
10mV/div
VOUT1
10mV/div
VOUT2
VIN
10mV/div
VOUT1
10mV/div
VOUT2
8
1kHz
60
PSRR (dB)
PSRR (dB)
70
10ms/div
20ms/div
Figure 18.
Figure 19.
Submit Documentation Feedback
Copyright © 2007–2008, Texas Instruments Incorporated
Product Folder Link(s): TPS718xx TPS719xx
TPS718xx
TPS719xx
www.ti.com..................................................................................................................................................... SBVS088C – FEBRUARY 2007 – REVISED MAY 2008
TYPICAL CHARACTERISTICS (continued)
Over operating temperature range (TJ = –40°C to +125°C), VIN = VOUT(TYP) + 0.5V or 2.7V, whichever is greater;
IOUT = 0.5mA, VEN1 = VEN2 = VIN, COUT = 1.0µF, unless otherwise noted. Typical values are at TJ = +25°C.
TPS719 ENABLE RESPONSE
POWER-UP/POWER-DOWN
IOUT = 200mA
VIN
6.5V
0V
EN1, EN2
4V/div
1V/div
1V/div
VOUT1
1V/div
VOUT2
40ms/div
VOUT
400ms/div
Figure 20.
Figure 21.
Copyright © 2007–2008, Texas Instruments Incorporated
Product Folder Link(s): TPS718xx TPS719xx
Submit Documentation Feedback
9
TPS718xx
TPS719xx
SBVS088C – FEBRUARY 2007 – REVISED MAY 2008..................................................................................................................................................... www.ti.com
APPLICATION INFORMATION
The TPS718xx/TPS719xx belong to a family of new
generation LDO regulators that use innovative
circuitry to achieve ultra-wide bandwidth and high
loop gain, resulting in extremely high PSRR (up to
1MHz) at very low headroom (VIN – VOUT). These
features, combined with low noise, two independent
enables, low ground pin current and ultra-small
packaging, make this part ideal for portable
applications. This family of regulators offer
sub-bandgap output voltages, current limit and
thermal protection, and is fully specified from –40°C
to +125°C.
VIN
0.9V - 3.6V
IN
1mF
VOUT
OUT1
TPS718xx
1mF
TPS719xx
On
EN1
0.9V - 3.6V
Off
VOUT
OUT2
On
Off
To improve ac performance such as PSRR, output
noise, and transient response, it is recommended that
the board be designed with separate ground planes
for VIN and VOUT, with each ground plane connected
only at the GND pin of the device. In addition, the
ground connection for the output capacitor should
connect directly to the GND pin of the device. High
ESR capacitors may degrade PSRR.
Internal Current Limit
Figure 22 shows the basic circuit connections.
2.7V - 6.5V
Board Layout Recommendations to Improve
PSRR and Noise Performance
1m F
EN2
GND
Figure 22. Typical Application Circuit
The TPS718xx/TPS719xx internal current limits help
protect the regulator during fault conditions. During
current limit, the output sources a fixed amount of
current that is largely independent of output voltage.
For reliable operation, the device should not be
operated in a current limit state for extended periods
of time.
The PMOS pass element in the TPS718xx/TPS719xx
has a built-in body diode that conducts current when
the voltage at OUT exceeds the voltage at IN. This
current is not limited, so if extended reverse voltage
operation is anticipated, external limiting to 5% of
rated output current may be appropriate.
Shutdown
Input and Output Capacitor Requirements
Although an input capacitor is not required for
stability, it is good analog design practice to connect
a 0.1µF to 1.0µF low equivalent series resistance
(ESR) capacitor across the input supply near the
regulator. This capacitor counteracts reactive input
sources and improves transient response, noise
rejection, and ripple rejection. A higher-value
capacitor may be necessary if large, fast rise-time
load transients are anticipated or if the device is
located close to the power source. If source
impedance is not sufficiently low, a 0.1µF input
capacitor may be necessary to ensure stability.
The TPS718xx/TPS719xx are designed to be stable
with standard ceramic capacitors of values 1.0µF or
larger at the output. X5R- and X7R-type capacitors
are best because they have minimal variation in value
and ESR over temperature. Maximum ESR should be
<1.0Ω.
10
Submit Documentation Feedback
The enable pin (EN) is active high and is compatible
with standard and low voltage, TTL-CMOS levels.
When shutdown capability is not required, EN can be
connected to IN. The TPS719 with internal active
output pulldown circuitry discharges the output with a
time constant (t) of:
t=3
60 ´ RL
´ COUT
60 + RL
with:
RL = output load resistance
COUT = output capacitance
Dropout Voltage
The TPS718xx/TPS719xx use a PMOS pass
transistor to achieve low dropout. When (VIN – VOUT)
is less than the dropout voltage (VDO), the PMOS
pass device is in its linear region of operation and the
input-to-output resistance is the RDS(ON) of the PMOS
pass element. VDO approximately scales with output
current because the PMOS device behaves like a
resistor in dropout.
Copyright © 2007–2008, Texas Instruments Incorporated
Product Folder Link(s): TPS718xx TPS719xx
TPS718xx
TPS719xx
www.ti.com..................................................................................................................................................... SBVS088C – FEBRUARY 2007 – REVISED MAY 2008
As with any linear regulator, PSRR and transient
response are degraded as (VIN – VOUT) approaches
dropout. This effect is shown in Figure 13 and
Figure 14 in the Typical Characteristics section.
Transient Response
As with any regulator, increasing the size of the
output capacitor will reduce over/undershoot
magnitude but increase duration of the transient
response.
Undervoltage Lock-Out (UVLO)
The TPS718xx/TPS719xx utilize an undervoltage
lock-out circuit to keep the output shut off until
internal circuitry is operating properly. The UVLO
circuit has a de-glitch feature so that it typically
ignores undershoot transients on the input if they are
less than 50µs duration. On the TPS719xx, the active
pulldown discharges VOUT when the device is in
UVLO off condition. However, the input voltage needs
to be greater than 0.8V for active pulldown to work.
Minimum Load
The TPS718xx/TPS719xx are stable with no output
load. Traditional PMOS LDO regulators suffer from
lower loop gain at very light output loads. The
TPS718xx/TPS719xx
employ
an
innovative,
low-current mode circuit under very light or no-load
conditions, resulting in improved output voltage
regulation performance down to zero output current.
THERMAL INFORMATION
Thermal Protection
Thermal protection disables the output when the
junction temperature rises to approximately +160°C,
allowing the device to cool. When the junction
temperature cools to approximately +140°C the
output circuitry is again enabled. Depending on power
dissipation, thermal resistance, and ambient
temperature, the thermal protection circuit may cycle
on and off. This cycling limits the dissipation of the
regulator, protecting it from damage due to
overheating.
Any tendency to activate the thermal protection circuit
indicates excessive power dissipation or an
inadequate heatsink. For reliable operation, junction
temperature should be limited to +125°C maximum.
To estimate the margin of safety in a complete design
(including
heatsink),
increase
the
ambient
temperature until the thermal protection is triggered;
use worst-case loads and signal conditions. For good
reliability, thermal protection should trigger at least
+35°C above the maximum expected ambient
condition of your particular application. This
configuration produces a worst-case junction
temperature of +125°C at the highest expected
ambient temperature and worst-case load.
The
internal
protection
circuitry
of
the
TPS718xx/TPS719xx has been designed to protect
against overload conditions. It was not intended to
replace proper heatsinking. Continuously running the
TPS718xx/TPS719xx
into
thermal
shutdown
degrades device reliability.
Power Dissipation
The ability to remove heat from the die is different for
each
package
type,
presenting
different
considerations in the printed circuit board (PCB)
layout. The PCB area around the device that is free
of other components moves the heat from the device
to the ambient air. Performance data for JEDEC lowand high-K boards are given in the Dissipation
Ratings table. Using heavier copper increases the
effectiveness in removing heat from the device. The
addition of plated through-holes to heat-dissipating
layers also improves the heatsink effectiveness.
Power dissipation depends on input voltage and load
conditions. Power dissipation (PD) is equal to the
product of the output current times the voltage drop
across the output pass element (VIN to VOUT), as
shown in Equation 1:
PD = (VIN - VOUT) x IOUT
(1)
Package Mounting
Solder pad footprint recommendations for the
TPS718xx/TPS719xxx are available from the Texas
Instruments web site at www.ti.com.
Copyright © 2007–2008, Texas Instruments Incorporated
Product Folder Link(s): TPS718xx TPS719xx
Submit Documentation Feedback
11
TPS718xx
TPS719xx
SBVS088C – FEBRUARY 2007 – REVISED MAY 2008..................................................................................................................................................... www.ti.com
1,690
1,590
1,088
0,988
Figure 23. YZC Wafer Chip-Scale Package Dimensions (in mm)
12
Submit Documentation Feedback
Copyright © 2007–2008, Texas Instruments Incorporated
Product Folder Link(s): TPS718xx TPS719xx
PACKAGE OPTION ADDENDUM
www.ti.com
19-Jan-2012
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package
Drawing
Pins
Package Qty
Eco Plan
(2)
Lead/
Ball Finish
MSL Peak Temp
Samples
(Requires Login)
TPS71812-33DRVR
ACTIVE
SON
DRV
6
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TPS71812-33DRVRG4
ACTIVE
SON
DRV
6
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TPS71812-33DRVT
ACTIVE
SON
DRV
6
250
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TPS71812-33DRVTG4
ACTIVE
SON
DRV
6
250
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TPS71818-27YZCR
ACTIVE
DSBGA
YZC
6
3000
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
TPS71818-27YZCT
ACTIVE
DSBGA
YZC
6
250
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
TPS71818-33DRVR
ACTIVE
SON
DRV
6
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TPS71818-33DRVT
ACTIVE
SON
DRV
6
250
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TPS71825-12DRVR
ACTIVE
SON
DRV
6
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TPS71825-12DRVT
ACTIVE
SON
DRV
6
250
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TPS71828-28YZCR
ACTIVE
DSBGA
YZC
6
3000
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
TPS71828-28YZCT
ACTIVE
DSBGA
YZC
6
250
Green (RoHS
& no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
TPS71828-30DRVR
ACTIVE
SON
DRV
6
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TPS71828-30DRVRG4
ACTIVE
SON
DRV
6
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TPS71828-30DRVT
ACTIVE
SON
DRV
6
250
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TPS71828-30DRVTG4
ACTIVE
SON
DRV
6
250
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TPS71913-28DRVR
ACTIVE
SON
DRV
6
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
Addendum-Page 1
(3)
PACKAGE OPTION ADDENDUM
www.ti.com
Orderable Device
19-Jan-2012
Status
(1)
Package Type Package
Drawing
Pins
Package Qty
Eco Plan
(2)
Lead/
Ball Finish
MSL Peak Temp
TPS71913-28DRVRG4
ACTIVE
SON
DRV
6
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TPS71913-28DRVT
ACTIVE
SON
DRV
6
250
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TPS71913-28DRVTG4
ACTIVE
SON
DRV
6
250
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TPS71918-12DRVR
ACTIVE
SON
DRV
6
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TPS71918-12DRVRG4
ACTIVE
SON
DRV
6
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TPS71918-12DRVT
ACTIVE
SON
DRV
6
250
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TPS71918-12DRVTG4
ACTIVE
SON
DRV
6
250
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TPS71918-28DRVR
ACTIVE
SON
DRV
6
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TPS71918-28DRVT
ACTIVE
SON
DRV
6
250
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TPS71921-22DRVR
ACTIVE
SON
DRV
6
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TPS71921-22DRVT
ACTIVE
SON
DRV
6
250
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TPS71926-15DRVR
ACTIVE
SON
DRV
6
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TPS71926-15DRVRG4
ACTIVE
SON
DRV
6
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TPS71926-15DRVT
ACTIVE
SON
DRV
6
250
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TPS71926-15DRVTG4
ACTIVE
SON
DRV
6
250
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TPS71928-28DRVR
ACTIVE
SON
DRV
6
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TPS71928-28DRVRG4
ACTIVE
SON
DRV
6
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TPS71928-28DRVT
ACTIVE
SON
DRV
6
250
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
Addendum-Page 2
(3)
Samples
(Requires Login)
PACKAGE OPTION ADDENDUM
www.ti.com
Orderable Device
19-Jan-2012
Status
(1)
Package Type Package
Drawing
Pins
Package Qty
Eco Plan
(2)
Lead/
Ball Finish
MSL Peak Temp
(3)
Samples
(Requires Login)
TPS71928-28DRVTG4
ACTIVE
SON
DRV
6
250
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TPS719285-285DRVR
ACTIVE
SON
DRV
6
3000
TBD
Call TI
Call TI
TPS719285-285DRVT
ACTIVE
SON
DRV
6
250
TBD
Call TI
Call TI
TPS719285-285DSET
PREVIEW
SON
DRV
6
TBD
Call TI
Call TI
TPS71933-28DRVR
ACTIVE
SON
DRV
6
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TPS71933-28DRVRG4
ACTIVE
SON
DRV
6
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TPS71933-28DRVT
ACTIVE
SON
DRV
6
250
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TPS71933-28DRVTG4
ACTIVE
SON
DRV
6
250
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TPS71933-33DRVR
ACTIVE
SON
DRV
6
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TPS71933-33DRVRG4
ACTIVE
SON
DRV
6
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TPS71933-33DRVT
ACTIVE
SON
DRV
6
250
TBD
Call TI
Call TI
TPS71933-33DRVTG4
ACTIVE
SON
DRV
6
250
TBD
Call TI
Call TI
TPS71936-315DRVR
ACTIVE
SON
DRV
6
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TPS71936-315DRVT
ACTIVE
SON
DRV
6
250
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Addendum-Page 3
PACKAGE OPTION ADDENDUM
www.ti.com
19-Jan-2012
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 4
PACKAGE MATERIALS INFORMATION
www.ti.com
18-Jul-2012
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
TPS71812-33DRVR
SON
DRV
6
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
3000
179.0
8.4
2.2
2.2
1.2
4.0
8.0
Q2
TPS71812-33DRVT
SON
DRV
6
250
179.0
8.4
2.2
2.2
1.2
4.0
8.0
Q2
TPS71818-33DRVR
SON
DRV
6
3000
179.0
8.4
2.2
2.2
1.2
4.0
8.0
Q2
TPS71818-33DRVT
SON
DRV
6
250
179.0
8.4
2.2
2.2
1.2
4.0
8.0
Q2
TPS71825-12DRVR
SON
DRV
6
3000
179.0
8.4
2.2
2.2
1.2
4.0
8.0
Q2
TPS71825-12DRVT
SON
DRV
6
250
179.0
8.4
2.2
2.2
1.2
4.0
8.0
Q2
TPS71828-30DRVR
SON
DRV
6
3000
179.0
8.4
2.2
2.2
1.2
4.0
8.0
Q2
TPS71828-30DRVT
SON
DRV
6
250
179.0
8.4
2.2
2.2
1.2
4.0
8.0
Q2
TPS71913-28DRVR
SON
DRV
6
3000
179.0
8.4
2.2
2.2
1.2
4.0
8.0
Q2
TPS71913-28DRVT
SON
DRV
6
250
179.0
8.4
2.2
2.2
1.2
4.0
8.0
Q2
TPS71918-12DRVR
SON
DRV
6
3000
179.0
8.4
2.2
2.2
1.2
4.0
8.0
Q2
TPS71918-12DRVT
SON
DRV
6
250
179.0
8.4
2.2
2.2
1.2
4.0
8.0
Q2
TPS71918-28DRVR
SON
DRV
6
3000
179.0
8.4
2.2
2.2
1.2
4.0
8.0
Q2
TPS71918-28DRVT
SON
DRV
6
250
179.0
8.4
2.2
2.2
1.2
4.0
8.0
Q2
TPS71921-22DRVR
SON
DRV
6
3000
179.0
8.4
2.2
2.2
1.2
4.0
8.0
Q2
TPS71921-22DRVT
SON
DRV
6
250
179.0
8.4
2.2
2.2
1.2
4.0
8.0
Q2
TPS71926-15DRVR
SON
DRV
6
3000
179.0
8.4
2.2
2.2
1.2
4.0
8.0
Q2
TPS71926-15DRVT
SON
DRV
6
250
179.0
8.4
2.2
2.2
1.2
4.0
8.0
Q2
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
18-Jul-2012
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
TPS71928-28DRVR
SON
DRV
6
3000
179.0
8.4
2.2
2.2
1.2
4.0
8.0
Q2
TPS71928-28DRVT
SON
DRV
6
250
179.0
8.4
2.2
2.2
1.2
4.0
8.0
Q2
TPS71933-28DRVR
SON
DRV
6
3000
179.0
8.4
2.2
2.2
1.2
4.0
8.0
Q2
TPS71933-28DRVT
SON
DRV
6
250
179.0
8.4
2.2
2.2
1.2
4.0
8.0
Q2
TPS71933-33DRVR
SON
DRV
6
3000
179.0
8.4
2.2
2.2
1.2
4.0
8.0
Q2
TPS71936-315DRVR
SON
DRV
6
3000
179.0
8.4
2.2
2.2
1.2
4.0
8.0
Q2
TPS71936-315DRVT
SON
DRV
6
250
179.0
8.4
2.2
2.2
1.2
4.0
8.0
Q2
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
TPS71812-33DRVR
SON
DRV
6
3000
203.0
203.0
35.0
TPS71812-33DRVT
SON
DRV
6
250
203.0
203.0
35.0
TPS71818-33DRVR
SON
DRV
6
3000
203.0
203.0
35.0
TPS71818-33DRVT
SON
DRV
6
250
203.0
203.0
35.0
TPS71825-12DRVR
SON
DRV
6
3000
203.0
203.0
35.0
TPS71825-12DRVT
SON
DRV
6
250
203.0
203.0
35.0
TPS71828-30DRVR
SON
DRV
6
3000
203.0
203.0
35.0
TPS71828-30DRVT
SON
DRV
6
250
203.0
203.0
35.0
TPS71913-28DRVR
SON
DRV
6
3000
203.0
203.0
35.0
TPS71913-28DRVT
SON
DRV
6
250
203.0
203.0
35.0
Pack Materials-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
18-Jul-2012
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
TPS71918-12DRVR
SON
DRV
6
3000
203.0
203.0
35.0
TPS71918-12DRVT
SON
DRV
6
250
203.0
203.0
35.0
TPS71918-28DRVR
SON
DRV
6
3000
203.0
203.0
35.0
TPS71918-28DRVT
SON
DRV
6
250
203.0
203.0
35.0
TPS71921-22DRVR
SON
DRV
6
3000
203.0
203.0
35.0
TPS71921-22DRVT
SON
DRV
6
250
203.0
203.0
35.0
TPS71926-15DRVR
SON
DRV
6
3000
203.0
203.0
35.0
TPS71926-15DRVT
SON
DRV
6
250
203.0
203.0
35.0
TPS71928-28DRVR
SON
DRV
6
3000
203.0
203.0
35.0
TPS71928-28DRVT
SON
DRV
6
250
203.0
203.0
35.0
TPS71933-28DRVR
SON
DRV
6
3000
203.0
203.0
35.0
TPS71933-28DRVT
SON
DRV
6
250
203.0
203.0
35.0
TPS71933-33DRVR
SON
DRV
6
3000
203.0
203.0
35.0
TPS71936-315DRVR
SON
DRV
6
3000
203.0
203.0
35.0
TPS71936-315DRVT
SON
DRV
6
250
203.0
203.0
35.0
Pack Materials-Page 3
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All
semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time
of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which
have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such
components to meet such requirements.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Mobile Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated