TI V62/05602-01XE

SCAS773A − JUNE 2004 − REVISED MARCH 2005
D Controlled Baseline
D
D
D
D
D
D
D
D ESD Protection Exceeds JESD 22
− One Assembly/Test Site, One Fabrication
Site
Enhanced Diminishing Manufacturing
Sources (DMS) Support
Enhanced Product-Change Notification
Qualification Pedigree†
Bidirectional Voltage Translator
2.3 V to 3.6 V on A Port and 3 V to 5.5 V on
B Port
Control Inputs VIH/VIL Levels Are
Referenced to VCCA Voltage
Latch-Up Performance Exceeds 250 mA Per
JESD 17
− 2000-V Human-Body Model (A114-A)
− 200-V Machine Model (A115-A)
− 1000-V Charged-Device Model (C101)
DB, DW, OR PW PACKAGE
(TOP VIEW)
VCCA
DIR
A1
A2
A3
A4
A5
A6
A7
A8
GND
GND
† Component qualification in accordance with JEDEC and industry
standards to ensure reliable operation over an extended
temperature range. This includes, but is not limited to, Highly
Accelerated Stress Test (HAST) or biased 85/85, temperature
cycle, autoclave or unbiased HAST, electromigration, bond
intermetallic life, and mold compound life. Such qualification
testing should not be viewed as justifying use of this component
beyond specified performance and environmental limits.
1
24
2
23
3
22
4
21
5
20
6
19
7
18
8
17
9
16
10
15
11
14
12
13
VCCB
NC
OE
B1
B2
B3
B4
B5
B6
B7
B8
GND
NC − No internal connection
description/ordering information
This 8-bit (octal) noninverting bus transceiver contains two separate supply rails. The B port is designed to track
VCCB, which accepts voltages from 3 V to 5.5 V, and the A port is designed to track VCCA, which operates at
2.3 V to 3.6 V. This allows for translation from a 3.3-V to a 5-V system environment and vice versa, from a 2.5-V
to a 3.3-V system environment and vice versa.
The SN74LVCC3245A is designed for asynchronous communication between data buses. The device
transmits data from the A bus to the B bus or from the B bus to the A bus, depending on the logic level at the
direction-control (DIR) input. The output-enable (OE) input can be used to disable the device so the buses are
isolated. The control circuitry (DIR, OE) is powered by VCCA.
ORDERING INFORMATION
−40°C
−40
C to 85
85°C
C
ORDERABLE
PART NUMBER
PACKAGE†
TA
TOP-SIDE
MARKING
SOIC − DW
Reel of 2000
CLVCC3245AIDWREP
LVCC3245A
SSOP − DB
Reel of 2000
CLVCC3245AIDBREP
LH245AEP
TSSOP − PW
Reel of 2000
CLVCC3245AIPWREP
LH245AEP
† Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are
available at www.ti.com/sc/package.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Copyright  2005, Texas Instruments Incorporated
!" # $%&" !# '%()$!" *!"&+
*%$"# $ " #'&$$!"# '& ",& "&# &-!# #"%&"#
#"!*!* .!!"/+ *%$" '$&##0 *&# " &$&##!)/ $)%*&
"&#"0 !)) '!!&"&#+
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
SCAS773A − JUNE 2004 − REVISED MARCH 2005
FUNCTION TABLE
(each transceiver)
INPUTS
OPERATION
OE
DIR
L
L
B data to A bus
L
H
A data to B bus
H
X
Isolation
logic diagram (positive logic)
2
DIR
22
OE
A1
3
21
B1
To Seven Other Channels
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
Supply voltage range, VCCA and VCCB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to 6 V
Input voltage range, VI: All A ports (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to VCCA + 0.5 V
All B ports (see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to VCCB + 0.5 V
Except I/O ports (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to VCCA + 0.5 V
Output voltage range, VO (see Note 2): All A ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to VCCA + 0.5 V
All B ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to VCCB + 0.5 V
Input clamp current, IIK (VI < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −50 mA
Output clamp current, IOK (VO < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −50 mA
Continuous output current, IO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±50 mA
Continuous current through VCCA, VCCB, or GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±100 mA
Package thermal impedance, θJA (see Note 3): DB package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63°C/W
DW package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46°C/W
PW package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88°C/W
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to 150°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. This value is limited to 4.6 V maximum.
2. This value is limited to 6 V maximum.
3. The package thermal impedance is calculated in accordance with JESD 51-7.
2
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SCAS773A − JUNE 2004 − REVISED MARCH 2005
recommended operating conditions (see Note 4)
VCCA
VCCA
VCCB
MIN
NOM
MAX
Supply voltage
2.3
3.3
3.6
V
Supply voltage
3
5
5.5
V
2.3 V
VIHA
VIHB
VILA
VILB
VIH
VIL
3V
1.7
2.7 V
3V
2
3V
3.6 V
2
3.6 V
5.5 V
2
2.3 V
3V
2
2.7 V
3V
2
3V
3.6 V
2
3.6 V
5.5 V
3.85
2.3 V
3V
0.7
2.7 V
3V
0.8
3V
3.6 V
0.8
3.6 V
5.5 V
0.8
2.3 V
3V
0.8
2.7 V
3V
0.8
3V
3.6 V
0.8
3.6 V
5.5 V
2.3 V
3V
1.7
2.7 V
3V
2
3V
3.6 V
2
3.6 V
5.5 V
2
2.3 V
3V
0.7
2.7 V
3V
0.8
3V
3.6 V
0.8
3.6 V
5.5 V
High-level input voltage
High-level input voltage
Low-level input voltage
Low-level input voltage
High-level input voltage (control pins)
(Referenced to VCCA)
Low-level input voltage (control pins)
(Referenced to VCCA)
VCCB
UNIT
V
V
V
V
1.65
V
V
0.8
VIA
VIB
Input voltage
0
Input voltage
0
VOA
VOB
Output voltage
0
Output voltage
0
VCCA
VCCB
V
VCCA
VCCB
V
V
V
NOTE 4: All unused inputs of the device must be held at the associated VCC or GND to ensure proper device operation. Refer to the TI application
report, Implications of Slow or Floating CMOS Inputs, literature number SCBA004.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
3
SCAS773A − JUNE 2004 − REVISED MARCH 2005
recommended operating conditions (see Note 4) (continued)
IOHA
IOHB
IOLA
VCCA
2.3 V
VCCB
3V
2.7 V
3V
−12
3.3 V
3V
−24
High-level output current
High-level output current
Low-level output current
IOLB
Low-level output current
∆t/∆v
Input transition rise or fall rate
MIN
NOM
MAX
UNIT
−8
2.3 V
3.3 V
−12
2.7 V
3.3 V
−12
3.3 V
3V
−24
2.3 V
3V
8
2.7 V
3V
12
3.3 V
3V
24
2.3 V
3.3 V
12
2.7 V
3.3 V
12
3.3 V
3V
24
10
mA
mA
mA
mA
ns/V
TA
Operating free-air temperature
−40
85
°C
NOTE 4: All unused inputs of the device must be held at the associated VCC or GND to ensure proper device operation. Refer to the TI application
report, Implications of Slow or Floating CMOS Inputs, literature number SCBA004.
4
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SCAS773A − JUNE 2004 − REVISED MARCH 2005
electrical characteristics over recommended operating free-air temperature range (unless
otherwise noted)
PARAMETER
TEST CONDITIONS
IOH = −100 µA
IOH = −8 mA
VOHA
VCCA
VCCB
MIN
TYP
3
3V
3V
2.9
2.3 V
3V
2
2.7 V
3V
2.2
2.5
3V
3V
2.4
2.8
2.2
2.6
IOH = −12 mA
VOLA
VOLB
3V
3V
2.7 V
4.5 V
2
2.3
IOH = −100 µA
3V
3V
2.9
3
2.3 V
3V
2.4
2.7 V
3V
2.4
2.8
3V
3V
2.2
2.6
IOH = −24 mA
2.7 V
4.5 V
3.2
4.2
IOL = 100 µA
IOL = 8 mA
3V
3V
2.3 V
3V
IOL = 12 mA
2.7 V
3V
0.1
0.5
3V
3V
0.2
0.5
IOL = 24 mA
2.7 V
4.5 V
0.2
0.5
IOL = 100 µA
IOL = 12 mA
3V
3V
2.3 V
3V
3V
IOL = 24 mA
3V
3.6 V
V
0.1
0.6
0.4
0.2
0.5
4.5 V
0.2
0.5
3.6 V
±0.1
±1
5.5 V
±0.1
±1
Control inputs
VI = VCCA or GND
IOZ†
A or B ports
VO = VCCA/B or GND,
VI = VIL or VIH
3.6 V
3.6 V
±0.5
±5
A port = VCCA or GND,
IO = 0
3.6 V
Open
5
50
ICCA
B to A
3.6 V
5
50
5.5 V
5
50
3.6 V
5
50
5.5 V
8
80
B port = VCCB or GND,
IO = 0
3.6 V
A to B
A port = VCCA or GND,
IO = 0
3.6 V
A port
VI = VCCA − 0.6 V, Other inputs at VCCA or GND,
OE at GND and DIR at VCCA
3.6 V
3.6 V
0.35
0.5
OE
VI = VCCA − 0.6 V, Other inputs at VCCA or GND,
DIR at VCCA
3.6 V
3.6 V
0.35
0.5
DIR
VI = VCCA − 0.6 V, Other inputs at VCCA or GND,
OE at GND
3.6 V
3.6 V
0.35
0.5
∆ICCB‡
B port
VI = VCCB − 2.1 V, Other inputs at VCCB or GND,
OE at GND and DIR at GND
3.6 V
5.5 V
1
1.5
Ci
Control inputs
Open
Open
4
∆ICCA‡
VI = VCCA or GND
VO = VCCA/B or GND
V
0.1
II
ICCB
UNIT
V
IOH = −24 mA
IOH = −12 mA
VOHB
MAX
V
µA
A
µA
µA
µA
A
mA
mA
pF
Cio
A or B ports
3.3 V
5V
18.5
pF
† For I/O ports, the parameter IOZ includes the input leakage current.
‡ This is the increase in supply current for each input that is at one of the specified voltage levels, rather than 0 V or the associated VCC.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
5
SCAS773A − JUNE 2004 − REVISED MARCH 2005
switching characteristics over recommended operating free-air temperature range (unless
otherwise noted) (see Figures 1 through 4)
PARAMETER
FROM
(INPUT)
TO
(OUTPUT)
tPHL
tPLH
A
B
tPHL
tPLH
B
A
tPZL
tPZH
OE
A
tPZL
tPZH
OE
B
tPLZ
tPHZ
OE
A
tPLZ
tPHZ
OE
B
VCCA = 2.5 V
± 0.2 V,
VCCB = 3.3 V
± 0.3 V
VCCA = 2.7 V
TO 3.6 V,
VCCB = 5 V
± 0.5 V
MIN
MAX
MIN
1
9.4
1
9.1
1
1
VCCA = 2.7 V
TO 3.6 V,
VCCB = 3.3 V
± 0.3 V
MAX
MIN
MAX
1
6
1
7.1
1
5.3
1
7.2
11.2
1
5.8
1
6.4
9.9
1
7
1
7.6
1
14.5
1
9.2
1
9.7
1
12.9
1
9.5
1
9.5
1
13
1
8.1
1
9.2
1
12.8
1
8.4
1
9.9
1
7.1
1
7
1
6.6
1
6.9
1
7.8
1
6.9
1
8.8
1
7.3
1
7.5
1
8.9
1
7
1
7.9
UNIT
ns
ns
ns
ns
ns
ns
operating characteristics, VCCA = 3.3 V, VCCB = 5 V, TA = 25°C
PARAMETER
TEST CONDITIONS
Outputs enabled
Cpd
Power dissipation capacitance per transceiver
Outputs disabled
TYP
UNIT
38
CL = 50,
f = 10 MHz
4.5
pF
power-up considerations†
TI level-translation devices offer an opportunity for successful mixed-voltage signal design. A proper power-up
sequence always should be followed to avoid excessive supply current, bus contention, oscillations, or other
anomalies caused by improperly biased device pins. To guard against such power-up problems, take these
precautions:
1. Connect ground before any supply voltage is applied.
2. Power up the control side of the device (VCCA for all four of these devices).
3. Tie OE to VCCA with a pullup resistor so that it ramps with VCCA.
4. Depending on the direction of the data path, DIR can be high or low. If DIR high is needed (A data to B bus),
ramp it with VCCA. Otherwise, keep DIR low.
† Refer to the TI application report, Texas Instruments Voltage-Level-Translation Devices, literature number SCEA021.
6
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SCAS773A − JUNE 2004 − REVISED MARCH 2005
PARAMETER MEASUREMENT INFORMATION FOR A PORT
VCCA = 2.5 V ± 0.2 V AND VCCB = 3.3 V ± 0.3 V
2 × VCC
S1
500 Ω
From Output
Under Test
Open
GND
CL = 30 pF
(see Note A)
500 Ω
TEST
S1
tpd
tPLZ/tPZL
tPHZ/tPZH
Open
2 × VCC
GND
LOAD CIRCUIT
tw
VCC
Timing
Input
VCC/2
VCC/2
VCC/2
0V
VOLTAGE WAVEFORMS
SETUP AND HOLD TIMES
VCC/2
VCC/2
0V
tPLH
Output
Control
(low-level
enabling)
tPLZ
VCC
VCC/2
tPZH
VOH
VCC/2
VOL
VCC/2
0V
Output
Waveform 1
S1 at 2 × VCC
(see Note B)
tPHL
VCC/2
VCC
VCC/2
tPZL
VCC
Input
VOLTAGE WAVEFORMS
PULSE DURATION
th
VCC
Data
Input
VCC/2
0V
0V
tsu
Output
VCC
VCC/2
Input
Output
Waveform 2
S1 at GND
(see Note B)
VOL + 0.15 V
VOL
tPHZ
VCC/2
VOH
VOH − 0.15 V
0V
VOLTAGE WAVEFORMS
ENABLE AND DISABLE TIMES
VOLTAGE WAVEFORMS
PROPAGATION DELAY TIMES
NOTES: A. CL includes probe and jig capacitance.
B. Waveform 1 is for an output with internal conditions such that the output is low, except when disabled by the output control.
Waveform 2 is for an output with internal conditions such that the output is high, except when disabled by the output control.
C. All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr ≤ 2 ns, tf ≤ 2 ns.
D. The outputs are measured one at a time, with one transition per measurement.
E. tPLZ and tPHZ are the same as tdis.
F. tPZL and tPZH are the same as ten.
G. tPLH and tPHL are the same as tpd.
H. All parameters and waveforms are not applicable to all devices.
Figure 1. Load Circuit and Voltage Waveforms
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
7
SCAS773A − JUNE 2004 − REVISED MARCH 2005
PARAMETER MEASUREMENT INFORMATION FOR B PORT
VCCA = 2.5 V ± 0.2 V AND VCCB = 3.3 V ± 0.3 V
2 × VCC
S1
500 Ω
From Output
Under Test
Open
GND
CL = 50 pF
(see Note A)
500 Ω
TEST
S1
tpd
tPLZ/tPZL
tPHZ/tPZH
Open
2 × VCC
GND
LOAD CIRCUIT
tw
VCC
Timing
Input
VCC/2
VCC/2
VCC/2
0V
VOLTAGE WAVEFORMS
SETUP AND HOLD TIMES
VCC/2
VCC/2
0V
tPLH
Output
Control
(low-level
enabling)
tPLZ
VCC
VCC/2
tPZH
VOH
VCC/2
VOL
VCC/2
0V
Output
Waveform 1
S1 at 2 × VCC
(see Note B)
tPHL
VCC/2
VCC
VCC/2
tPZL
VCC
Input
VOLTAGE WAVEFORMS
PULSE DURATION
th
VCC
Data
Input
VCC/2
0V
0V
tsu
Output
VCC
VCC/2
Input
Output
Waveform 2
S1 at GND
(see Note B)
VOL + 0.15 V
VOL
tPHZ
VCC/2
VOH
VOH − 0.15 V
0V
VOLTAGE WAVEFORMS
ENABLE AND DISABLE TIMES
VOLTAGE WAVEFORMS
PROPAGATION DELAY TIMES
NOTES: A. CL includes probe and jig capacitance.
B. Waveform 1 is for an output with internal conditions such that the output is low, except when disabled by the output control.
Waveform 2 is for an output with internal conditions such that the output is high, except when disabled by the output control.
C. All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr ≤ 2 ns, tf ≤ 2 ns.
D. The outputs are measured one at a time, with one transition per measurement.
E. tPLZ and tPHZ are the same as tdis.
F. tPZL and tPZH are the same as ten.
G. tPLH and tPHL are the same as tpd.
H. All parameters and waveforms are not applicable to all devices.
Figure 2. Load Circuit and Voltage Waveforms
8
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SCAS773A − JUNE 2004 − REVISED MARCH 2005
PARAMETER MEASUREMENT INFORMATION FOR B PORT
VCCA = 3.6 V AND VCCB = 5.5 V
2 × VCC
S1
500 Ω
From Output
Under Test
Open
GND
CL = 50 pF
(see Note A)
500 Ω
TEST
S1
tPLH/tPHL
tPLZ/tPZL
tPHZ/tPZH
Open
2 × VCC
Open
LOAD CIRCUIT
tw
VCC
B-Port
Input
50% VCC
50% VCC
0V
VOLTAGE WAVEFORMS
PULSE DURATION
VCC
1.5 V
Input
1.5 V
B-Port
Output
50% VCC
VOH
50% VCC
VOL
VOLTAGE WAVEFORMS
PROPAGATION DELAY TIMES
NONINVERTING OUTPUTS
1.5 V
1.5 V
0V
tPLZ
t
Output PZL
Waveform 1
50% VCC
S1 at 2 × VCC
(see Note B)
0V
tPHL
tPLH
2.7 V
Output
Control
VCC
VOL + 0.3 V
VOL
tPHZ
tPZH
Output
Waveform 2
S1 at Open
(see Note B)
50% VCC
VOH − 0.3 V
VOH
≈0 V
VOLTAGE WAVEFORMS
ENABLE AND DISABLE TIMES
LOW- AND HIGH-LEVEL ENABLING
NOTES: A. CL includes probe and jig capacitance.
B. Waveform 1 is for an output with internal conditions such that the output is low, except when disabled by the output control.
Waveform 2 is for an output with internal conditions such that the output is high, except when disabled by the output control.
C. All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr ≤ 2.5 ns, tf ≤ 2.5 ns.
D. The outputs are measured one at a time, with one transition per measurement.
E. All parameters and waveforms are not applicable to all devices.
Figure 3. Load Circuit and Voltage Waveforms
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
9
SCAS773A − JUNE 2004 − REVISED MARCH 2005
PARAMETER MEASUREMENT INFORMATION FOR A AND B PORT
VCCA AND VCCB = 3.6 V
7V
S1
500 Ω
From Output
Under Test
Open
GND
CL = 50 pF
(see Note A)
500 Ω
TEST
S1
tPLH/tPHL
tPLZ/tPZL
tPHZ/tPZH
Open
7V
Open
LOAD CIRCUIT
tw
2.7 V
1.5 V
Input
1.5 V
0V
VOLTAGE WAVEFORMS
PULSE DURATION
2.7 V
1.5 V
Input
1.5 V
Output
Waveform 1
S1 at 7 V
(see Note B)
0V
tPHL
tPLH
VOH
Output
1.5 V
1.5 V
VOL
VOLTAGE WAVEFORMS
PROPAGATION DELAY TIMES
NONINVERTING OUTPUTS
2.7 V
Output
Control
1.5 V
1.5 V
0V
tPLZ
tPZL
3.5 V
1.5 V
tPHZ
tPZH
Output
Waveform 2
S1 at Open
(see Note B)
VOL + 0.3 V
VOL
1.5 V
VOH − 0.3 V
VOH
≈0 V
VOLTAGE WAVEFORMS
ENABLE AND DISABLE TIMES
LOW- AND HIGH-LEVEL ENABLING
NOTES: A. CL includes probe and jig capacitance.
B. Waveform 1 is for an output with internal conditions such that the output is low, except when disabled by the output control.
Waveform 2 is for an output with internal conditions such that the output is high, except when disabled by the output control.
C. All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr ≤ 2.5 ns, tf ≤ 2.5 ns.
D. The outputs are measured one at a time, with one transition per measurement.
E. All parameters and waveforms are not applicable to all devices.
Figure 4. Load Circuit and Voltage Waveforms
10
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
PACKAGE OPTION ADDENDUM
www.ti.com
30-Jan-2012
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package
Drawing
Pins
Package Qty
Eco Plan
(2)
Lead/
Ball Finish
MSL Peak Temp
CLVCC3245AIDBREP
ACTIVE
SSOP
DB
24
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
CLVCC3245AIDWREP
ACTIVE
SOIC
DW
24
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
CLVCC3245AIPWREP
ACTIVE
TSSOP
PW
24
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
V62/05602-01XE
ACTIVE
TSSOP
PW
24
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
V62/05602-01YE
ACTIVE
SSOP
DB
24
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
V62/05602-01ZE
ACTIVE
SOIC
DW
24
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
(3)
Samples
(Requires Login)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
30-Jan-2012
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF SN74LVCC3245A-EP :
• Catalog: SN74LVCC3245A
NOTE: Qualified Version Definitions:
• Catalog - TI's standard catalog product
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jul-2012
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
CLVCC3245AIDBREP
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
SSOP
DB
24
2000
330.0
16.4
8.2
8.8
2.5
12.0
16.0
Q1
CLVCC3245AIDWREP
SOIC
DW
24
2000
330.0
24.4
10.85
15.8
2.7
12.0
24.0
Q1
CLVCC3245AIPWREP
TSSOP
PW
24
2000
330.0
16.4
6.95
8.3
1.6
8.0
16.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jul-2012
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
CLVCC3245AIDBREP
SSOP
DB
24
2000
367.0
367.0
38.0
CLVCC3245AIDWREP
SOIC
DW
24
2000
367.0
367.0
45.0
CLVCC3245AIPWREP
TSSOP
PW
24
2000
367.0
367.0
38.0
Pack Materials-Page 2
MECHANICAL DATA
MSSO002E – JANUARY 1995 – REVISED DECEMBER 2001
DB (R-PDSO-G**)
PLASTIC SMALL-OUTLINE
28 PINS SHOWN
0,38
0,22
0,65
28
0,15 M
15
0,25
0,09
8,20
7,40
5,60
5,00
Gage Plane
1
14
0,25
A
0°–ā8°
0,95
0,55
Seating Plane
2,00 MAX
0,10
0,05 MIN
PINS **
14
16
20
24
28
30
38
A MAX
6,50
6,50
7,50
8,50
10,50
10,50
12,90
A MIN
5,90
5,90
6,90
7,90
9,90
9,90
12,30
DIM
4040065 /E 12/01
NOTES: A.
B.
C.
D.
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
Body dimensions do not include mold flash or protrusion not to exceed 0,15.
Falls within JEDEC MO-150
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All
semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time
of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which
have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such
components to meet such requirements.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Mobile Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated