05016 587B051 thru 587B301 Only One Name Means ProTek’Tion™ 120V AC POWER LINE SURGE SUPPRESSOR APPLICATIONS ✔ Hard Wired Equipment AC Power Protection ✔ Load Side Distribution Systems ✔ Secondary Protection for Light Industrial AC Power IEC COMPATIBILITY (EN61000-4) ✔ 61000-4-5 (Surge): 1kA, 8/20µs - Level 4(Line-Line) & 333A Level 4(Line-Ground) FEATURES U.S PATENT 4,563,720 ✔ ✔ ✔ ✔ ✔ ✔ Meets ANSI/IEEE C62.41 Requirements Listed to CSA, File LR65240 Differential and Common Mode Protection Low Clamping Voltage Nanosecond Response Time Long Life and Maintenance Free FIGURE 1 TRANSIENT VOLTAGE THREAT CONDITION 8 ✔ Plastic Package ✔ Weight: 485 Grams (Approximate) ✔ Flammability Rating UL 94V-0 ✔ Device Marking: Part Number, Date Code, Logo, Voltage and Current Rating Kilovolts 6 MECHANICAL CHARACTERISTICS 4 2 0 0 05016.R4 12/03 1 40 50 60 6 4 2 0 0 The 587B Series offers a high degree of protection against 120 VAC EMI line noise. It is ideal for protecting 400 Volt components because the solid state TVS technology assures that the line-to-neutral voltage will not exceed 400 Volts. While the modules are designed for transient voltage protection, the advanced circuitry will also attenuate the amplitude and slow the rate of rise of high frequency noise acting as an EMI filter. The 587B Series includes differential mode and common mode protection, which is effective in reducing interference from line to equipment and are effective in reducing equipment generated noise to meet FCC, VDE and CSA interference requirements. 30 FIGURE 2 TYPICAL CLAMPING ACTION OF A 16 AMP MODULE Kilovolts This series is designed to protect AC powered equipment from the 6,000 Volt peak open circuit voltage and 3,000 Amp short circuit current as defined in ANSI/IEEE C62.41, Category C1. 20 Time - µs DESCRIPTION The 587B Series of 120 Volt AC Surge Suppressors is designed for use by the OEM, equipment installer and or maintenance contractor. These modules employ a three stage technology proven to be the most cost effective and reliable method in protecting sensitive electronic equipment from over voltage transients. 10 10 20 30 Time - µs 40 50 60 Figures 1 and 2 are photographs of digitized waveforms showing the typical clamping action of a 16 ampere module. A 12 Ohm resistor is used to represent a 10 Amp equipment load. The load is then subjected to the ANSI/IEEE C62.41 Category CI test conditions (6,000V/3,000A). These photographs contrast the effect on equipment with and without the protector. www.protekdevices.com 587B051 thru 587B301 DEVICE CHARACTERISTICS SPECIFICATIONS @ 25°C RESPONSE TO TRANSIENT VOLTAGES MAXIMUM RATINGS Operating Line Voltage: 130 VAC Max Maximum Line Current: 587B051: 5A 587B151: 15A 587B201: 20A (Line-to-Neutral Only) 587B301: 30A Transient Voltage: 6000Vpeak Transient Current: 3000Apeak Current Leakage: Line-to-Neutral: Neutral-to-Ground: Storage & Operating Temperature: (Measured at center of mounting surface) @ 130 VAC 1.0mA 0.5mA CLAMPING TEST CONDITION PROTECTION MODE MAXIMUM CLAMPING VOLTAGE OPEN CIRCUIT VOLTAGE @ 1.2/50 µs SHORT CIRCUIT CURRENT @ 8/20 µs DIFFERENTIAL (Line-to-Neutral) 295V 350V 1000V 6000V 500A 3000A COMMON (Neutral-to-Ground) 500V 650V 1000V 6000V 500A 3000A FILTER CHARACTERISTICS (Noise Attenuation dB) -40°C to 85°C Frequency (MHz) Common Mode Attenuation Differential Mode Attenuation 0.15 10 30 0.5 25 55 1.0 35 55 5.0 55 55 10 50 50 30 40 45 ARRESTER DEFINITIONS Clamping Voltage: The clamping voltage of an arrester is the voltage that appears across its terminals during conduction of a transient current. Standard Wave Form: The waveform of a surge current or voltage is designated by a combination of two numbers. The first number is for the time of the wave front expressed in microseconds from zero to the peak of the wave. The second number is for the time of the wavetail also expressed in microseconds from zero to the instant that the wavetail reaches one half of the crest or peak value, i.e., 8/20 µs waveform. Transient Current: The transient current of an arrestor is the peak surge current which flows through the arrester when voltage clamping occurs. OPERATION For maximum effectiveness, the protector should be installed directly after the AC line on/off switch and fuse. This will protect the electronics from the AC line switch arcing and the severe transients caused by a fuse clearing. Some heat is produced when operating at full current load, and heat sinking may be required to maintain case temperature below 85°C. The case temperature is measured at the center of the mounting surface. The unit should not be mounted to a low combusting temperature material such as wood. High energy transients will cause a large circulating current in the AC input line (2,500A is possible). To prevent electromagnetic coupling, the AC line on the input side of the protector must be dressed away from other wiring, magnetic shielding may be required. In addition, the electrical service must be connected to a low impedance earth ground. 05016.R4 12/03 2 www.protekdevices.com 587B051 thru 587B301 PACKAGE OUTLINE & DIMENSIONS D F C LINE OUT Model 587B051 120V 50/60 Hz NEUTRAL B 37464-00001 LINE IN E INCLUDES HARDWARE 2 NUTS, 2 WASHERS PER TERMINAL 5 AMP GROUND 0.169” Nom. Dia. 2 Places A PROTEK PART NUMBER 587B051 587B151 587B201 587B302 CASE (INCHES) A 2 3 3 3 B 2 2 3 3 C 2.5 3.5 3.5 3.5 D 2.85 3.85 3.85 3.85 CASE (CENTIMETERS) E 1.5 1.5 1.5 1.5 F 0.6 0.6 0.6 0.6 B 5.08 5.08 7.62 7.62 A 5.08 7.62 7.62 7.62 COPYRIGHT © ProTek Devices 2003 SPECIFICATIONS: ProTek reserves the right to change the electrical and or mechanical characteristics described herein without notice (except JEDEC). DESIGN CHANGES: ProTek reserves the right to discontinue product lines without notice, and that the final judgement concerning selection and specifications is the buyer’s and that in furnishing engineering and technical assistance, ProTek assumes no responsibility with respect to the selection or specifications of such products. 05016.R4 12/03 3 C 6.35 8.89 8.89 8.89 D 7.62 10.16 10.16 10.16 E 3.81 3.81 3.81 3.81 F 1.52 1.52 1.52 1.52 APPROX. WEIGHT IN GRAMS TERMINAL THREADS 250 500 750 850 #8-32 #8-32 M5 M5 ProTek Devices 2929 South Fair Lane, Tempe, AZ 85282 Tel: 602-431-8101 Fax: 602-431-2288 E-Mail: [email protected] Web Site: www.protekdevices.com www.protekdevices.com