Grid to Chip Surge Protection

Power Switching & Controls
For Business-Critical ContinuityTM
Grid to Chip Surge Protection
Product Catalog
Contact
Surge Protection
100 Emerson Parkway
Binghamton, NY 13905
T: 607-721-8840 (Outside U.S.)
T: 800-288-6169 (U.S. & Canada Only)
F: 607-722-8713
E: [email protected]
Emerson Network Power.
The global leader in enabling Business-Critical ContinuityTM.
EmersonNetworkPower. com/surge
AC Power
Embedded Computing
Infrastructure Management & Monitoring
Thermal Management
Connectivity
DC Power
Embedded Power
Industrial Power
Outside Plant
Power Switching & Controls
Racks & Integrated Cabinents
Service
Business-Critical Continuity, Emerson Network Power and the Emerson Network Power logo are trademarks and service marks of Emerson Electric Co.
©2014 Emerson Electric Co.
While every precaution has been taken to ensure accuracy and completeness in this literature, Emerson Network Power assumes no responsibility, and disclaims all liability
for damages resulting from use of this information or for any errors or omissions.
SL-30900 Rev.3 1/14 Printed in USA
Power Quality Solutions for
ALL Your Application Needs
“Dirty” power is a problem. Whether it’s called a
surge, spike, transient or noise, “dirty” power is an abnormality in
the power that runs your facility. These power problems can leave
buildings in the dark and disable equipment, costing you thousands
in repairs and lost revenue. Your productivity uptime and reputation
depend on consistent power quality. Emerson Network Power Surge
Protection provides products and solutions that ensure reliability
from Grid to Chip. For more than 40 years, Facility Managers,
Engineers, and System Integrators have trusted Emerson Network
Power Surge Protection products to protect critical equipment in
the Industrial Process, Computing, Research/Testing and
Communications fields.
Emerson Network Power Surge Protection and the IEEE Standard
1100-1999 (Emerald Book) recommend a properly rated surge
protection device should be applied on ALL electrical conductors
entering your facility including: power, voice, and data. Without
proper protection – data disruption, hardware stress or destruction
could occur.
As a line of defense against damaging transients, Emerson Network
Power Surge Protection manufactures products in the following
categories:
■ Surge Protection Devices (SPDs) — which focus on
limiting high-voltage spikes to an acceptable level
■ Filtering/Line Conditioning — protect against low-energy
transients and high frequency noise and finally…
■ Data/Signal Line Protection — products guard sensitive
instrumentation against what we refer to as ‘backdoor’
transients and noise.
Why allow “dirty” power to put your equipment at risk? Turn
to Emerson Network Power Surge Protection products for
peace of mind. We provide solutions for all your application needs
and the foundation for Business-Critical Continuity™.
Table of Contents
Technical Bulletins — Surge Protection for Power and Signal Lines
Products
Page #
TVSS/SURGE PROTECTION DEVICES (SPDs)
TVSS/SPDs — Product Selection Guide
Emerson Network Power DRS Series
Edco EMC-240B — Low Exposure AC Panel Protection
Edco FAS-120AC — Medium Exposure AC Panel Protection
2
3
4
4
FILTERING/LINE CONDITIONING
TM
Filtering/Line Conditioning — Product Selection Guide
Islatrol™ IE Series — Active Tracking Filter™
Islatrol™ IC+/LRIC+ Series — Active Tracking Filter™
Islatrol™ — SP-6TVN — Industrial Strength Surge Suppression (Series)
Islatrol™ — RM Series — 120 VAC Rackmount
TM
5
6, 7
8, 9
10
11
DATA/SIGNAL LINE PROTECTION
TM
TM
Data/Signal Line Protection — Product Selection Guide
Edco™ DRS (DC) Series — DIN Rail Protection
Edco™ PC642 Series — Zone/Loop/Data
Edco™ PHC Series — Two-Pair Signaling Circuit Protector (Modular)
Edco™ RJA-RJD Series — RJ-45 Telephone/Data
Edco™ RM-CAT6-16POE — CAT6-16POE Channel Rackmount
Edco™ CX-HFN-FF/CX-HFN-FM — High Frequency Line Protector — N-Type
Edco™ SLAC Series — AC Power/Signal
Edco™ SS64 & SS65 Series — Wastewater/Industrial Applications
Edco™ CX Series — CCTV & Data Applications/Coax
Edco™ RM-CXO6-16R — Channel Rackmount
Edco™ CAT6-5 POE Series
TECHNICAL BULLETINS
High-Density Multiple Input Rack
Surge Protection for the Water Industry
Surge Protection for Power and Signal Lines
Note: Refer to EmersonNetworkPower.com/surge for most current product information.
NOTES:
1. SLAC UNIT PROVIDES ONE POWER AND TWO SIGNAL PROTECTION CIRCUITS.
2. SURGE DEVICES SHOULD BE GROUNDED LOCALLY WITH A GROUND ROD,
AND ALSO AT THE MAIN PANEL ELECTRICAL GROUND.
3. CHECK WITH EMERSON NETWORK POWER SURGE PROTECTION, INC. TO
DETERMINE IF OUTPUT CAN BE SURGE PROTECTED.
24
12
13
14
15
16
17
17
18
19
20
20
21
22
23
24
Technical Bulletins
TVSS/Surge Protective Devices (SPDs)
TVSS/SPDs — Product Selection Guide
Technical Bulletins — Surge Protection for the Water Industry
Find your application in the left column.
Then look across for the appropriate product (s).
PRODUCTS
APPLICATIONS
DRS
Series
TM
Edco
EMC
Series
Edco
FAS
Series
TM
Facility Service
Entrance
Distribution Panels
TM
TM
Sub-Distribution
Panels
Branch Panelboards
(Commercial)
TM
Branch Panelboards
(Residential)
Motor Control Centers
Control Panels
(AC Power)
NOTES:
1. SLAC UNIT PROVIDES ONE POWER AND TWO SIGNAL PROTECTION CIRCUITS.
Various OEM Equipment
2
2. SURGE DEVICES SHOULD BE GROUNDED LOCALLY WITH A GROUND ROD,
AND ALSO AT THE MAIN PANEL ELECTRICAL GROUND.
3. CHECK WITH EMERSON NETWORK POWER SURGE PROTECTION, INC. TO
DETERMINE IF OUTPUT CAN BE SURGE PROTECTED.
23
Technical Bulletins
TVSS/Surge Protective Devices (SPDs)
DRS Series
Technical Bulletins — High-Density Multiple Input Rack
The DRS is a modular surge protective device (SPD) that is designed for easy
installation in control panels using standard DIN rail mounting brackets. The DRS
devices offer both normal and common surge protection up to 40 kA per phase.
Features
■ Effectively handles high-energy transients
on TT, TN-C, TN-S and TN-C-S three-phase
power systems
■ SPD rated Type 2 in accordance with
EN 61643-11; Class I & II in accordance
with IEC 61643-1
■ Built-in thermal components disconnect
SPD from the power source to avoid
thermal runaway conditions
■ MOV only or MOV+Gas Tube models
available
■ Fast response time, high surge current
capability, low voltage protection levels
■ Visual inspection window on each module
indicates status
■ 3-pole terminal provides remote status
monitoring
■ DIN rail mounting and plug-in module
design allow for easy installation,
maintenance and replacement of
surge element
■ 5 year warranty
TM
How to Specify the Appropriate Model
Example: DRS 120 3 1 Q
Nominal Voltage
(Un) (XXX)
# of Metal Oxide Varistor Modules*
(X)
# of Gas Tube Modules**
(X)
120
0
0
230
1
1
240
2
277
3
346
4
TM
Q
*MOV modules are typically one module per phase and may be wired L-N, L-G or N-G.
**Gas Tube modules typically used in the N-G mode for type TT grounding systems.
***Certain applications require higher rated components in order to survive frequent
voltage rises, in this case order a unit with a “Q” at the end of the part number.
480
TM
Higher Rated Voltage***
(Optional)
Replacement modules available: Order DRS + Un + M (for MOV) or G (for Gas Tube)
TM
Performance Technical Specifications
DRS12031
TM
System Voltage
Type of Network
DRS27731
DRS34631
120/208,
230/400, 220/380, 277/480,
127/220 VAC
240/415 VAC 254/440 VAC
TT-TN
TT-TN
TT-TN
L-N; N-PE
L-N; N-PE
L-N; N-PE
Nominal Voltage
Un–120 V
Un–230 V
Un–277 V
Un–346 V
Rated Voltage
(MCOV)
Uc–150 V
Uc–320 V
Uc–320 V
Uc–420 V
1. SLAC UNIT PROVIDES ONE POWER AND TWO SIGNAL PROTECTION CIRCUITS.
Nominal Discharge
Current (8 x 20 µs)
1n–20 kA
2. SURGE DEVICES SHOULD BE GROUNDED LOCALLY WITH A GROUND ROD,
AND ALSO AT THE MAIN PANEL ELECTRICAL GROUND.
Maximum
Discharge Current
Imax–40 kA
3. CHECK WITH EMERSON NETWORK POWER SURGE PROTECTION, INC. TO
DETERMINE IF OUTPUT CAN BE SURGE PROTECTED.
TT-TN
346/600 VAC
Modes of Protection L-N; N-PE
NOTES:
1n–20 kA
Imax–40 kA
Up–1.6 kV
1n–20 kA
Imax–40 kA
Up—1.6 kV
1n–20 kA
Imax–40 kA
Up–1.2 kV
Response Time
TS–25 ns
TS–25 ns
TS–25 ns
TS–25 ns
95%
95%
95%
95%
> 103 MV
> 103 MV
> 103 MV
> 103 MV
Isolation
Resistance
Test Standards
EN 61643-11
Type 2
IEC61643- 1:1998-02
Class II
Mechanical
Characteristics
Dimensions (Length x Width x Height)
70.8mm x 90.5mm x 68mm
I/O Connections
By Screw Terminal: 4-25 mm2
By Connection Bus
MOV Encapsulation Material
Disconnection Indicator
Voltage Protection
Level
Relative Humidity
22
DRS23031
Electrical
Characteristics
Up–2.0 kV
Status Monitoring
Mounting
Operation Temperature Range
Degree of Protection
Disconnection Device
Housing Material
Epoxy Resin
Mechanical Indicator
Remote Alarm Terminals
Symmetrical Rail (EN50022/DIN46277-3)
-40°C to +85°C
IP 20
Thermal Cutoff System
ABS/PA UL94V0
3
TVSS/Surge Protective Devices (SPDs)
Data/Signal Line Protection
Edco EMC-240B
120/240 VAC Low Exposure AC Panel Protection
Edco™ CAT6-5POE Series
The Edco EMC-240B surge suppressor is designed to protect AC distribution
panel circuits or 120V power supplies feeding sensitive electronic equipment.
CAT6/CAT5 Power Over Ethernet
Electrically, the unit incorporates MOV and thermal fusing technology. The Edco
The Edco™ CAT6-5POE Series is designed to work on Category 5 Power-Over-
EMC 240B is designed to be installed in parallel on standard single phase
Ethernet transmission lines as well as Category 6 applications. Ideal to protect
120VAC (L,N,G) circuits.
expensive equipment against surges and transients entering a building on
exposed transmission lines.
Features
■ Fast response time
■ Operational status indicators
■ 40,000 Amps per phase capacity
■ UL 1449 Third Edition, Type 2 listed
■ Failsafe and fused
■ 5 year warranty
General Technical Specifications
Operating Voltage
120/240 VAC
VPR
L-N:600V, L-L:1,200V
Fault Current Rating
42 kAIC
UL Location
Type 2
I-Nominal (kA)
Total Peak Surge Current
■ Applications up to 60 VDC @ 300 mA
■ Exceeds CAT5 & 6 transmission values
■ 1 year warranty
■ CAT5 POE compatible
Operating Frequency
47-63 Hz
EMI Attenuation (100 kHz to 100 MHz)
SPD Technology
> 40 dB
Metal Oxide Varistors (MOVs)
Modes of Protection
Line-to-Line,
Line-to-Neutral
3kA
Operating Current
Features
Operating Temperature
Dimensions (Inches)
-40°C to +85°C
Weight
Certifications
■ CAT6 compatible
4.6H x 2.2W x 2.8L
13.5 oz
ANSI/UL 1449 Third Edition
Type 2, CUL
General Technical Specifications
Ordering Information
NA, Parallel
Status Indication
Power On & MOVs functional
Operating Voltage
60 VDC
Connection Type
80 kA (8 x 20 µs)
Connection Type
Wire Leads
Clamping Voltage
65 VDC
Operating Temperature
Operating Current
300 mA
Dimensions (Inches)
Peak Surge Current
Edco FAS-120AC
™
Frequency Range
Insertion Loss
120 VAC Medium Exposure AC Panel Protection
SPD Technology
60A (10 x 1000 µs)
Weight
RJ-45 Jacks
RJ-45 (Female-Female)
CAT6-5POE-FF
-40°C to +85°C
0.8H x 1.0W x 2.3L
1 oz
0 to 250 MHz
< 0.1 dB at 20 MHz
Silicon Avalanche Diode (SAD)
The Edco FAS-120AC surge suppressor is designed to protect AC panel
circuits or 120V power supplies feeding sensitive electronic equipment.
Electrically the unit incorporates MOV and thermal fusing technology. This device is
designed to be installed in parallel on standard single phase 120VAC (L,N,G) circuits.
Installation can be close-nipple up to a distribution panel/circuit or hardwired
in parallel up to power supply input terminal screws. Be sure to dress leads as
short as possible.
Features
■ LED indicator
■ Compact size
■ Fast response time
■ Liquid tight conduit fitting
■ Thermal fuse
■ 5 year warranty
■ L-G, L-N, & N-G protection
General Technical Specifications
Operating Voltage
VPR
120 VAC
L-N:700V, L-G:700V, N-G:700V
UL Location
I-Nominal
Operating Current
Total Peak Surge Current
Operating Frequency
4
Type 2
3 kA
EMI Attenuation (100 kHz to 100 MHz)
SPD Technology
Modes of Protection
Line-to-Neutral,
Dimensions (Inches)
Weight
Certifications
2.5H x 1.5W x 3.0L
4.2 oz
ANSI/UL 1449 Third Edition
Line-to-Ground, Neutral-to-Ground
NA, Parallel
Status Indication
15.5 kA (8 x 20 µs)
Connection Type
47-63 Hz
> 25 dB
Metal Oxide Varistors (MOVs)
Power On & MOV Functional
Operating Temperature
Wire Leads
-40°C to +85°C
21
Data/Signal Line Protection
Filtering/Line Conditioning
Edco™ CX Series
CCTV & Data Applications/Coax
The Edco™ CX06-M & Edco™ CX06-MI Surge Protective Devices (SPDs)
implement three-stage hybrid technology. The SPDs address over-voltage
transients with a primary Gas Discharge Tube (GDT), and secondary Silicon
Avalanche Diode (SAD) components. Over-current protection, e.g. sneak and
Filtering/Line Conditioning — Product Selection Guide
Find your application in the left column.
Then look across for the appropriate product.
fault currents, are mitigated with solid-state resettable fuses — PTCs. The Edco™
CX06-M & Edco™ CX06-MI SPDs are designed in accordance with NFPA 780
PRODUCTS
(2004 edition) requirements, with up to 20 kA of surge current capability. The
Edco™ CX06-MI model has an isolated ground and is recommended for use at the
camera end.
APPLICATIONS
Features
■ Sneak/fault current protection
■ CX06-MI has an isolated ground
■ Low insertion loss
■ 5 year warranty
Islatrol™
IE
Series
Islatrol™
IC+/LRIC+
Series
Islatrol™
SP-6TVN
Series
Islatrol™
RM
Series
■ Shielded case
General Technical Specifications
Operating Voltage
Ordering Information
5 VDC
Connection Type
Clamping Voltage
6 VDC
Operating Temperature
Operating Current
0.15 A
Dimensions (Inches)
Peak Surge Current
Frequency Range
Insertion Loss
SPD Technology
20 kA (8 x 20 µs)
0 to 20MHz
< 0.1 dB at 20 MHz
Programmable Logic
Controllers
Weight
BNC, 50/75 Ohm
Head End
-40°C to +85°C
Camera End
CX06-MI
M = 1.5H x 1W x 3.25L
MI = 1.5H x 1W x 4L
Camera End
CX06-MI-SBL
M = 2.3 oz
Certifications
*
CX06-M
MI = 3 oz
UL 497B
Control Panels
(AC Power)
*
*
Various OEM
Equipment
*
*
GDT, SAD, w/Series PTC
Edco™ RM-CX06-16R
Channel Rackmount
The Edco™ RM-CX06-16R Surge Protective Device (SPD) is a 16 channel coax
SPD implementing three-stage hybrid technology. The SPD addresses overvoltage transients with a primary Gas Discharge Tube (GDT), and secondary
Silicon Avalanche Diode (SAD) components. Over-current protection, e.g.,
sneak and fault currents, are mitigated with new solid-state resettable fuses —
PTCs. The Edco™ RM-CX06-16R SPD is designed in accordance with NFPA 780
(2004 edition) requirements, with up to 20 kA of surge current capability.
Home
Entertainment/Office
*
Features
■ Sneak/fault current protection
■ 16 channel
■ Low insertion loss
■ 1 year warranty
■ Shielded case
AC Rack Equipment
General Technical Specifications
Operating Voltage
5 VDC
Frequency Range
Clamping Voltage
6 VDC
Insertion Loss
Operating Current
0.15 A
SPD Technology
Peak Surge Current
20
20 kA (8 x 20 µs)
Connection Type
0 to 100 MHz
< 0.1 dB at 20 MHz
GDT, SAD, w/Series PTC
BNC, 50/75 Ohm
Operating Temperature
Dimensions (Inches)
Weight
Certifications
-40°C to +85°C
1.75H x 19W x 2.0D (1U)
3.2 lbs
UL 497B
5
Filtering/Line Conditioning
Data/Signal Line Protection
Islatrol™ IE Series
Edco™ SS64 & SS65 Series
Active Tracking Filter™
Wastewater/Industrial Applications
The Islatrol IE is a series-connected DIN or flange mounted high-
The Edco™ SS64 and Edco™ SS65 Series suppressors are designed for the water
frequency noise filter and surge suppressor. Its ideal applications include
and wastewater industry. These multi-stage hybrid suppressors address
critical industrial loads drawing up to 20 Amps of continuous current,
over-voltage transients with gas tube and silicon avalanche technology. In
while typical applications include any microprocessor-based products,
addition, sneak and fault currents are mitigated with PTC devices which
including industrial PLCs, OEM applications, and motion control systems.
consist of solid-state resettable fuses. The units are encapsulated in stainless
™
steel pipe nipples making them suitable for use in severe environments. The
Edco™ SS64 models protect a signal pair and the Edco™ SS65 models protect a
Features
■ Multi-staged design, combining a unique
hybrid clamping network with the active
tracking technology of the Islatrol ® family
■ Surge current capacity — 45,000 Amps
■ Transient protection in all modes: line
to neutral, line to ground, and neutral
to ground
signal pair plus the cable shield (drain wire).
■ LED status indication and form C contact
for remote indication
■ DIN mountable enclosure
■ ANSI/UL 1449 Third Edition Type 4,
1283, CUL recognized, CE
Features
■ 10 year warranty
■ Transient protection for
low-voltage signal lines
■ Encapsulated in stainless steel
pipe nipples
■ Sneak/fault current protection
■ Protection for one pair
(Two wires & shield on SS65)
■ Resettable fusing—PTCs
Performance Technical Specifications General Technical Specifications
Ordering Information
Model
Voltage*
IE-103
IE-105
IE-110
IE-120
L-N
400V
400V
IE-203
IE-205
IE-210
IE-220
L-G
600V
600V
N-G
L-L
600V
N/A
500V
N/A
MCOV
700V
900V
700V
Peak Surge Current Capability (8 x 20 µs)
5 Amps
IE-105
120 V
10 Amps
IE-110
120 V
20 Amps
IE-120
Continuous Current
Model
275 VRMS
Line Frequency
47 - 63 Hz
Terminal
Mounting Type
DIN/Flange
Weight
< 3 lbs
Voltage*
3 Amps
IE-203
Response Time
Normal Mode
< 0.5 ns
240 V
5 Amps
IE-205
Maximum Signal Voltage
28 V Max
< 5 ns
240 V
10 Amps
IE-210
DC Clamping Level (L-G)
36 V ±l0%
-40°C to +45°C
240 V
20 Amps
IE-220
DC Clamping Level (L-L)
72 V ±l0%
Operating Temperature
Derate Linearly to 60% at +70ºC
Operating Humidity
* All voltage configurations are single phase - 2 wire + gnd.
Common Mode
100 kHz to 50 MHz - 90 dB Min
5 MHz to 50 MHz - 60 dB Min
Maximum let-thru Voltage:
Dimensional Diagram
Line-to-Line (10x700 µs)
Normal Mode/Common Mode
(Zero Volts Bias)
5 Amp
0.7 V/292 V
10 Amp
0.7 V/300 V
20 Amp
0.7 V/300 V
90 V @ 400 A
Series Resistance (per conductor)
Typical Category A Ringwave (6 kV, 200 A, 100 kHz)
1 V/300 V
44 V @ 400 A
Maximum let-thru Voltage:
Capacitance:
3 Amp
Typical Applications
< 1 Nanosecond
Line-to-Ground (10x700 µs)
0% to 95%
Frequency Response (Forward-Reverse)
Normal Mode
General Technical Specifications
240 V
Common Mode
■ 5 year warranty
■ Automatic recovery
Response Time
15,000 Amps
15,000 Amps
120 V
240 Volt
15,000 Amps
45,000 Amps
IE-103
120 V
Line to Ground
Total
Model
3 Amps
150 VRMS
Line to Neutral
Neutral to Ground
Continuous Current
120 Volt
Connection
1,000V
■ Differential and common mode protection
Number of Occurrences
5 V (typical)
(L-L) 600 pf typical
(L-G) 1200 pf typical
400 @ 500 Amps
(10x1000 µs)
Typical Category B Ringwave (6 kV, 500 A, 100 kHz)
Normal Mode/Common Mode
6
3 Amp
178 V/300 V
5 Amp
162 V/291 V
10 Amp
153 V/300 V
20 Amp
200 V/300 V
Caution: The hybrid design of this product includes series resistance. Do not place this product
in service on any signal lines capable of supplying more than 150 milliamperes continuously.
19
Data/Signal Line Protection
Filtering/Line Conditioning
Edco™ SLAC Series
Islatrol™ IE Series
AC Power/Signal
Active Tracking Filter™
The Edco SLAC Series suppressor is specifically designed to protect electronic
™
instruments used by the water/wastewater industries. It combines hybrid AC
power protection and signal line protection in a NEMA-4X polycarbonate case.
System Design
The AC power suppressor can supply up to 1875 Watts and has a 15 Amp
replaceable fuse to prevent overloading of the protective elements. A “Power
ON” LED provides visual indication that power is applied to instruments. Signal
line protection is accomplished by the Edco™ PC642 Series available in a variety
of voltage clamps. Signal current can be monitored by reading the voltage
Shunt Absorbing Components
line side sine wave tracking circuitry
Shunt Absorbing Components
load side sine wave tracking circuitry
across the 10 V, 1% resistors (TP1 & TP2 or TP3 & TP4). All leads going to the
Edco™ SLAC board are terminated by quick disconnect or barrier block
Finger Safe Terminals
IEC 998 approved terminals
connectors to facilitate easy removal for service or replacement.
Form C Relay Contacts
normally open and normally closed dry
contact for remote status monitoring
Features
■ Optional twist lock plug lightning & surge
suppression for AC power and low-voltage
signal lines
■ Test jacks for signal line monitoring
■ Series hybrid AC suppressor/filter
■ Optional stainless steel or fiberglass
enclosure
■ Plug-in protection module
■ 15 Amp replaceable fuse
General Technical Specifications
AC Power
Technology
Three-Stage Series Hybrid
Input Voltage
15 Amps Max.
Response Time
<5 Nanoseconds
Maximum Surge Current (8x20 µs)
Normal Mode
(L-N)
■ 5 year warranty
MOV Array
high-energy surge current diversion
array providing transient protection
line to neutral, line to ground, and
neutral to ground
Silicon Avalanche Diodes
fast responding surge current
diversion components
■ ANSI/UL 1449 Third Edition
Optional Enclosure
Glass-Filled Polycarbonate Base
Cover Molded in Clear Polycarbonate
Series Blocking Inductor
voltage blocking current
soothing inductor
Pulse Capacitor
high-frequency noise absorption
DIN Rail Mountable
mounts to standard 35 mm
industrial DIN rail; rotates 90°
for mounting flexibility
Knockouts for 1/2" and 3/4" hubs
10 kA
Occurrences at 500 Amps
■ “Power ON” indicator
NEMA-4X
120 VAC 50/60 Hz
Output Current
Parameter
Standard Enclosure
Unit Status Indicator
green LED monitors the operational
status of the Elite Series
Bosses for 6 BZ x 3/8" Self-Tapping Screws
>50
Maximum Protection—Total Insulation
Common Mode
(L-G) (N-G)
Corrosion Resistant
Resists Temperature of 248°F
IEEE 587 CAT A Ring*
172 V
280 V
Flammability Rating UL94-5V
IEEE 587 CAT B Ring*
205 V
280 V
IEEE 587 CAT B Impulse* 330 V
360 V
Nominal Outside dimensions (Inches)
How to Specify the Appropriate Model
H= 6.89, W=6.89, D=2.95
Connection Diagram
*Measured from zero volts, 90° Phase angle
General Technical Specifications
Signal Line
Signal Protector Technology
AC Protector Technology
Peak Surge Current
Response Time
Voltage Clamp (customer selected)
Series Resistance
18
GDT, PTC, SAD
MOV, Fuse
10 kA
Ordering Information
These blocks are for PC642
VoltageSelection if applicable. See
PC 642 Datasheet for additional
information. 0 3 6 L C is standard
for 4-20 mA Signal Line.
<1 Nanosecond
8–200 Volts
5 ! (Typical)
7
Filtering/Line Conditioning
Data/Signal Line Protection
Edco™ RM-CAT6-POE Series
CAT6-POE Channel Rackmount
Islatrol IC+/LRIC+ Series
™
The Edco™ RM-CAT6-POE Series is a multi-channel high-speed data line protector
Active Tracking Filter™
that utilizes a three-stage hybrid design technology. This unit addresses high-
Series connected high-frequency noise filter with transient protection. Offers
energy voltage transients that can damage expensive computer equipment. Ideal
the flexibility of either receptacle/line cord connection or hard-wired connection
for network switches and hubs, the Edco™ RM-CAT6-POE Series is easily mounted
to critical loads (up to 30 Amperes). Applications include industrial or office
in close proximity to the protected equipment.
equipment, computers placed in harsh environments.
Features
■ Low insertion loss
■ Exceeds category 6 transmission values
■ Three stage hybrid
■ Compact 1U rack size
■ 1 year warranty
■ Meets Power-Over-Ethernet (POE)
requirements
■ Replaceable surge modules
Features
■ Typically reduces normal mode transients
to +/-2 volts
■ Surge current capacity — 45,000 Amps
■ LED power indication
■ 10 year warranty
■ Transient protection in all modes: line
to neutral, line to ground, and neutral
to ground
General Technical Specifications
Operating Voltage
57 V
Clamping Voltage
68 V
Transmission Speed
MCOV
Typical Category A Ringwave (6 kV, 200 A, 100 kHz)
120 Volt
150 VRMS
Model
Normal
275 VRMS
IC+102 / LRIC+102
1.0 / 0.9
302 / 287
Line Frequency
47 - 63 Hz
IC+105 / LRIC+105
0.7 / 0.8
292 / 307
IC+107 / LRIC+107
0.7 / 0.7
302 / 293
Response Time
Normal Mode
< 0.5 ns
Common Mode
< 5 ns
Operating Temperature
-40°C to +45°C at Full Load
Derate Linearly to 60% at +70ºC
0% to 95%
Operating Humidity
System Design
Common
240 Volt
IC+115 / LRIC+115
0.7 / 0.7
304 / 306
IC+130 / IC+202
0.5 / 1.1
306 / 536
IC+205 / IC+207
1.5 / 0.8
628 / 616
IC+215 / IC+230
0.6 / 0.9
572 / 566
Typical Category B Ringwave (6 kV, 500 A, 100 kHz)
10 Mbps,
100 Mbps, 1,000 Mbps
Operating Current
0.15 A
Connection Means
2-Port Series
SPD Technology
GDT, SAD, W/Series PTC
Series Blocking Inductors
voltage blocking current
smoothing inductors
Shunt Absorbing Components
sine wave tracking circuitry
Modes of Protection
Signal High-Low,
Signal High-Ground,
Signal Low-Ground
Peak Surge Current
Mounting
Dimensions
10 kA (8 x 20 µs)
Insertion Loss
<0.1 dB
VSWR
<1.2
Operating Humidity
Painted Steel
1.75Hx19Wx6.3D
Weight
5.5 lbs
Warranty
1 Year
Ordering Information
0-95% Non-Condensing
Operating Temperature
Rackmount
Enclosure Type
-40°C to +85°C
RM-CAT6-8POE
8 Channels
Input Connection Type
RJ-45
RM-CAT6-16POE
16 Channels
Output Connection Type
RJ-45
RM-CAT6-24POE
24 Channels
RM-CAT6-48POE
48 Channels
Edco™ CX-HFN Series
MOV Transient Protection
high-energy transient
protection line to neutral,
line to ground,
neutral to ground
High Frequency Coax Protector — N-Type
The Edco™ CX-HFN surge protectors are designed to protect sensitive electronic
Model
Normal
Common
Peak Surge Current Capability (8 x 20 µs)
IC+102 / LRIC+102
178 / 188
302 / 285
Line to Neutral
15,000 Amps
IC+105 / LRIC+105
162 / 191
291 / 300
Line to Ground
15,000 Amps
IC+107 / LRIC+107
173 / 190
300 / 298
Neutral to Ground
15,000 Amps
IC+115 / LRIC+115
153 / 149
307 / 309
IC+130 / IC+202
241 / 302
299 / 532
also has a replaceable protection cartridge (CX-RC). The Edco™ CX-HFN
Load Surge Current Rating
equipment from damage due to excessive voltage or currents generated by
Pulse Capacitor
high-frequency noise absorption
lightning or static build-up.
The Edco™ CX-HFN offers low signal loss at frequencies up to 4 gigahertz. The unit
10 mSec
5 x Nominal
IC+205 / IC+207
378 / 336
594 / 596
accommodates both bulkhead mount and stud mount. The input and output
1 sec
3 x Nominal
IC+215 / IC+230
272 / 342
548 / 578
10 sec
2 x Nominal
connections are interchangeable.
Packaging
• High Impact Plastic Case
• Vacuum Impregnated Magnetics
• Epoxy Encapsulated
Frequency Response (Forward-Reverse)
Normal Mode
■ Low signal loss
Connection Diagram
■ 5 year warranty
General Technical Specifications
Ordering Information
TM
100 kHz to 50 MHz - 90 dB Min
5 MHz to 50 MHz - 60 dB Min
Features
Note: All measurements in volts. IEEE test results with
no AC applied. Normal mode—L1-N or L1-L2;
Common mode—L-G, N-G or L1-G, L2-G.
TM
Common Mode
Operating Voltage
130 VDC
Insertion Loss
Clamping Voltage
(DC Spark Over Voltage)
150 VDC
SPD Technology
Operating Current
Peak Surge Current
1A
10 kA (8 x 20 µs)
Maximum Power
10 Watts
Impedence
50 Ohms
Frequency Range
8
■ Up to 48 channels available
■ UL 1283, CSA recognized
< 0.3 dB to 0.5 dB 2 to 3 GHz
Gas Discharge Tube (GDT)
Connection Type
Female N-Type
Operating Temperature
-30°C to +85°C
Dimensions (Inches)
Weight
CX-HFN-FF (Female–Female)
CX-HFN-FM (Female-Male)
1.25H x .875W x 2.5L
4 oz
0 to 4 GHz
17
Data/Signal Line Protection
Filtering/Line Conditioning
Islatrol™ IC+/LRIC+ Series
Active Tracking Filter™
Edco RJA-RJD Series
™
RJ-45 Telephone/Data
Ordering Information
Dimensional Diagram
The Edco RJA and Edco RJD Series are four pair telephone/data line
™
™
120 VAC Models with barrier strip at input and output/with wire leads at input and output (WL)
protectors that implement advanced two stage hybrid design. These units
B
A
F
address over-voltage transients with silicon breakover devices, while sneak
and fault currents are mitigated with PTC technology, which consists of solid
C
state resettable fuses.
The Edco™ RJA and Edco™ RJD Series incorporate RJ-45 female jacks in and out.
M
DIMOUN
EN TING
SIO
NS
D
The Edco™ RJA voltage clamp is set for C.O. Trunks and Analog Telephone
G
E
Model
Rated
Output
(Amps)
Case
Dimensions (In)
AxBxC
Mounting Flange
Dimensions (In)
DxExFxG
Screw
Size
Weight
(lbs)
IC+102 / IC+102WL
2.5
4 x 2.88 x 1.81
4.38 x 2.12 x 5.31 x 0.19
#6
1.0
IC+105 / IC+105WL
5.0
4 x 2.88 x 1.81
4.38 x 2.12 x 5.31 x 0.19
#6
1.3
IC+107 / IC+107WL
7.5
4.75 x 4.75 x 2.35
5.25 x 3.50 x 6.25 x 0.19
#6
2.0
IC+115 / IC+115WL
15
6.25 x 4.75 x 2.35
6.75 x 3.50 x 7.75 x 0.19
#8
3.5
IC+130 / IC+130WL
30
7.75 x 4.75 x 2.35
8.25 x 3.50 x 9.00 x 0.19
#8
6.0
Extensions (with ring in voltage), and the Edco™ RJD voltage clamp is set for
120 VAC Models with 5 foot line cord and single NEMA 5-15 receptacle
Digital Extensions (no ring in voltage).
Features
■ <1 nanosecond response time
■ Tip and ring to ground protection
■ Solid-state resettable fuses-PTCs
■ CAN/CSA C22.2, No. 226-92 Compliant
■ Silicon breakover technology
■ Low capacitance
■ 4 pair protection
■ Line-to-line protection
■ 5 year warranty
Case
Dimensions (In)
AxBxC
Mounting Flange
Dimensions (In)
DxExFxG
Screw
Size
Weight
(lbs)
LRIC+102
2.5
4.5 x 3.0 x 1.88
N/A
N/A
1.3
LRIC+105
5.0
4.5 x 4.5 x 2.38
N/A
N/A
2.0
LRIC+107
7.5
6.0 x 4.5 x 2.38
N/A
N/A
2.3
LRIC+115
15
7.5 x 4.5 x 2.38
N/A
N/A
4.0
240 VAC Models with barrier strip at input and output/with wire leads at input and output (WL)
B
■ UL 497A listed
Model
Rated
Output
(Amps)
A
F
C
D
M
DIMOUN
EN TING
SIO
NS
G
E
Model
Rated
Output
(Amps)
Case
Dimensions (In)
AxBxC
Mounting Flange
Dimensions (In)
DxExFxG
Screw Weight
Size
(lbs)
IC+202 / IC+202WL
2.5
4 x 2.88 x 1.81
4.38 x 2.12 x 5.31 x 0.19
#6
1.3
IC+205 / IC+205WL
5.0
4.75 x 4.75 x 2.35
5.25 x 3.50 x 6.25 x 0.19
#6
2.0
IC+207 / IC+207WL
7.5
6.25 x 4.75 x 2.35
6.75 x 3.50 x 7.75 x 0.19
#8
3.3
IC+215 / IC+215WL
15
7.75 x 4.75 x 2.35
8.25 x 3.50 x 9.00 x 0.19
#8
5.8
IC+230 / IC+230WL
30
7.75 x 4.75 x 2.35
8.25 x 3.50 x 9.00 x 0.19
#8
6.0
Islatrol™ Active Tracking Filters™ carry a 10 year warranty
General Technical Specifications
Ordering Information
Operating Voltage
48, 220 VDC
Analog Phone
RJA-45
Clamping Voltage
55, 280 VDC
Digital Phone
RJD-45
Operating Current
0.15 A
Peak Surge Current
Frequency Range
Insertion Loss
SPD Technology
Connection Type
Operating Temperature
Dimensions (Inches)
Weight
Certifications
16
Installation
200 A (10 x 1000 µs)
0 to 50 MHz
< 0.1 dB at 50 MHz
Silicon Breakover
Devices w/Series PTC
RJ-45 Jacks
-40°C to +85°C
1.0H x 2.5W x 4.25L
3 oz
UL 497A, CUL,
The Edco™ RJA and Edco™
RJD Series are intended
for indoor use only
and shall be employed
on the equipment side of
a listed primary
telephone protector.
9
Filtering/Line Conditioning
Data/Signal Line Protection
Edco™ PHC Series
Islatrol™ — SP-6TVN
Two-Pair Signaling Circuit Protector (Modular)
Industrial Strength Surge Suppression (Series)
The Edco™ PHC Series is designed to protect two pairs of wires specifically for
The Islatrol™ SP-6TVN plug-in unit is an Active Tracking Filter™ which plugs into
alarm and security systems where operating currents can be as high as 5 Amps.
a standard duplex receptacle. It features uniquely designed repositionable
Electrically, the Edco™ PHC Series is a rugged series hybrid implementing a
outlets for easy installation behind desks and other furniture. It protects
staged complement of MOVs, copper wound inductors and Silicon Avalanche
sensitive home or office equipment from damaging power disturbances
Diodes. This design reduces series resistance to 0.2 Ohms per pair. These
traveling through wiring to electrical outlets.
products are intended to mate with an Edco PCB1B-WKEY gold-plated female
terminal connector.
The Edco™ PHC modules plug into a base assembly (Edco™ PCB1B-WKEY). The
base assembly can be mounted to any flat surface and should be located as close
Features
Repositionable Outlets
as practical to the protected equipment. Terminal 1 and/or terminal 10 should
■ Plugs into standard 120 V, 15 Amp
electrical outlet
■ Perfect for tight spaces, behind furniture
and appliances
■ Total peak surge current capacity of
39,000 Amps
■ Intelligent monitoring against improper
wiring/grounding
■ Cables for telephone, video, and
data connections
■ 60 dB maximum high frequency
■ Three-stage protection
■ Continuous current up to 5 Amps
■ Operational indicator lamp
■ Differential protection
■ UL 497B listed
■ 5 year limited warranty
■ Common mode protection
■ Requires Edco ™ PCB1B-WKEY base
■ Plug-in module
■ PC642PTU (Pass Thru Unit)
available for troubleshooting
■ Repositionable outlets rotate to
accommodate available space
be connected to Building-Approved Ground with 12 or 10 gauge solid wire.
Features
EDCO PCB1B-WKEY BASE SOLD SEPARATELY
■ Automatic recovery
General Technical Specifications
■ Fast response time
AC Power Protection
VPR
L-N:330V, L-G:400V, N-G:400V
Nominal Operating Voltage
120 VAC, Single Phase
Operating Voltage Range
120 VAC +/- 10%
Operating Frequency Range
47 — 63 Hz
Rated Output (Amps)
15 Amperes
ANSI/IEEE C62.41 Category
Connection Type
265 V
Common Mode
290 V
ANSI/IEEE C62.41 Cat B Ringwave (6 kV, 500 A, 100 kHz)
Normal Mode
275 V
Common Mode
290 V
Category A & B
(6) 5-15R Receptacles and
5-15P Plug
Phase Configuration
2 Wire + Gnd
Size
High Impact Plastic
Weight
Common Mode
L — N, L — G, N — G
Indication of Suppression Status
Status Indicator
Response Time
Warranty
Maximum Continuous Operating Voltage (MCOV)
Line to Neutral
5 Year
Connection Type
Cables Provided
Peak Surge Current
Capacitance
Protection Level
130 VAC
Clamping Voltage (DC)
Attenuation
Peak Surge Current (8 x 20 ms)
Line to Neutral
13,000 Amps
Line to Ground
13,000 Amps
Neutral to Ground
13,000 Amps
Total
39,000 Amps
36-70 VDC
Clamping Voltage
43-100 VDC
Operating Current
40 dB Maximum, forward/reverse, 5 MHz to 50 MHz
Video 1 & 2
Phone
Network
Type “F”
Type RJ-11
Type RJ-45
6' (2x) Type “F”
6' Ends
6' RJ-11 Male
6' Ends
6' RJ-45 Male
Ends
5 kA
(8 x 20 µs)
2 kA
(10 x 1000 µs)
3 kA
(8 x 20 µs)
<12 pf
<50 pf
<70 pf
L-G
T-R, T-G, R-G
L-G (8 Lines)
145 V
270-350 V
30 V
1 dB @ 2 Ghz
N/A
N/A
-WKEY
Ordering Information
How to Specify the Appropriate Model
5A
Peak Surge Current
10 kA (8 x 20 µs)
0 to 10 MHz
Insertion Loss
< 0.1 dB at 10 MHz
SPD Technology
Low Voltage Protection
< .5 ns Normal Mode
ANSI/UL 1449 Third Edition Type 3
Operating Voltage
Connection Type
2.0 lbs (0.9 kgs)
Modes Of Protection
10
60 dB Maximum, forward/reverse, 100 kHz to 50 MHz
Terminal Assignments
General Technical Specifications
Frequency Range
Frequency Response
Normal Mode
7.5 x 4.75 x 1.75 (Inches)
Enclosure
Certifications
ANSI/IEEE C62.41 Cat A Ringwave (6 kV, 200 A, 100 kHz)
Normal Mode
■ 5 year warranty
MOV, SAD, w/Series Inductor
Terminal block
w/compression lugs
Terminals accept up to 10 AWG
Operating Temperature
Dimensions (Inches)
-40°C to +85°C
3.7H x 1.75W x 2.375L
(PHC + Mounting Base)
Weight
DO NOT daisy chain grounds. NOT intended for shield
termination. Install ground in accordance with all
applicable codes.
Dimensions
8 oz
Certifications
UL 497B
Applications Part Number
24V Horn, Strobe, Bell:
70V Speaker Lines:
PHC-043 & PCB1B-WKEY
PHC-SP70 & PCB1B-WKEY
-WKEY
15
Data/Signal Line Protection
Filtering/Line Conditioning
Edco™ PC642 Series
Islatrol™ — RM Series
Zone/Loop/Data
120 VAC Rackmount
The Edco™ PC642 Series surge suppressor is a two-pair (four-wire) module
Islatrol™ RM Series AC rackmount surge protector is ideal for protecting the
implementing three-stage hybrid technology. This module addresses
power feeding valuable rack equipment. Status LEDs indicate the correct power
over-voltage transients with gas tubes and silicon avalanche components. In
is coming to the unit, whether the unit is properly grounded and whether the
addition, sneak and fault currents are mitigated with resettable fuses (PTCs).
surge components are still intact. Units are available with a digital meter,
The PTCs increase resistance several orders of magnitude when over-currents
mounted on the front of the unit, which will monitor the voltage, current and
Model shown: RM-115-10 RM
power of the protected equipment.
exceed safe levels. A normal state resumes when over-currents are removed.
The ability to self-restore in this manner significantly increases suppressor
EDCO PCB1B-WKEY BASE SOLD SEPARATELY
performance and survivability.
The Edco™ PC642 card edge module is gold-plated, double-sided, and is
designed to mate with the Edco™ PCB1B-WKEY gold-plated female terminal
connector. When snapped together, the data circuits “pass thru” the protector
Features
in a serial fashion from the four “Field Side” terminals to the four “Electronics
■ 40 kA surge protection
■ Digital meter
Side” terminals. Terminals 1 or 10 of the Edco™ PCB1B-WKEY must be attached
■ 60 dB max noise filtering
■ Optional twist lock plug
to Building-Approved Ground per Edco™ Technical Bulletin # 2015.
■ 15 & 20 A models available
■ 1 year warranty
■ Power, ground and surge status indicators
Features
■ Three-stage hybrid protection
■ Fast response time
■ Sneak/fault current protection
■ Requires Edco ™ PCB1B-WKEY base
■ Resettable fusing — PTCs
■ PC642PTU (Pass Thru Unit)
available for troubleshooting
■ Low capacitance option
■ 5 year warranty
■ Plug-in module
General Technical Specifications
Maximum Continuous
Operating Voltage (MCOV)
5-250 VDC
Clamping Voltage
8-300 VDC
Operating Current
150mA
Peak Surge Current
Operating Temperature
Dimensions (Inches)
Weight
Certifications
-40°C to +85°C
2H x 1W x 2.5L
(PC642 + Mounting Base)
14
PC642C-008LC
RS423, Token Ring:
PC642C-008LC
RS232:
PC642C-036LC
DO NOT daisy chain grounds.
NOT intended for shield termination.
Install ground in accordance with
all applicable codes.
Amperage
Plug (NEMA)
Receptacles (NEMA)
Digital Meter
Locking Plug
120 V
15 A
5-15P
5-15R
Yes
No
RM-120-10RM
120 V
20 A
5-20P
5-20R
Yes
No
PC642C-030LC-036LC
ANSI/UL 1449 Third Edition
VPR
PC642C-036LC
Rated Voltage
24 VAC Power
PC642C-043LC
Rated Current
Peak Surge Current
Response Time
EMI/RFI Filtering
How to Specify the Appropriate Model
PC642CLow Capacitance,
LC Line to Line, Line to Ground
D Line to Line protection only
1 oz
Line to Ground
008
036
043
200
Max Operating
Voltage
Clamping
Voltage
(1000V@1mA)
5 VDC
30 VDC
36 VDC
43-250 VDC
8 VDC
36 VDC
43 VDC
300 VDC
008, 036, 043 models
only
008, 043 models only
200 models only
Output Receptacles
15A Models
Rackmount AC Power Protection
4–20ma:
-WKEY
UL 497B
Caution: The hybrid design of this product includes
series resistance. Do not place this product in
service on any signal line capable of supplying
more than 150 milliamperes continuously.
RS485, RS422:
E-NET, 10 BASE T:
GDT, SAD, w/Series PTC
Terminal block
w/compression lugs
Terminals accept up to 10 AWG
Voltage
RM-115-10RM
APPLICATION:
-WKEY
< 0.1 dB at 20 MHz
SPD Technology
Model
Ordering Information
0 to 20 MHz
Insertion Loss
Connection Type
Terminal Assignments
10 kA (8 x 20 µs)
Frequency Range
General Technical Specifications
LED Indicators
Digital Meter
(Optional)
Input Power
15 A Models
20A Models
L-N:400 V, L-G:500V, N-G:400V
120 V
15 A & 20 A
20 kA/mode, 40 kA/phase
<5 ns
60 dB Max
Green-Power on
Green-Ground OK
Green-Surge Circuit OK
20A Models
Thermal Protection
Overcurrent Protection
Dimensions
Certifications
Warranty
Front- (2) NEMA 5-15R
Back- (10) NEMA 5-15R
Front- (2) NEMA 5-20R
Back- (10) NEMA 5-20R
Thermal Protected MOVs
Circuit
1.75"H x 19"W x 3.8"D (1U)
ANSI/UL 1449 Third Edition Type 3
1 Year
Voltage Amps, Watts, VA, Hz, PF,
Kwh, and Clock
SJT 14/3C Power Cord (9 ft)
with NEMA 5-15P Plug
SJT 12/3C Power Cord (9 ft)
with NEMA 5-20P Plug
NEMA L5-20P Plug- Optional
11
Data/Signal Line Protection
Data/Signal Line Protection
Edco™ DRS (DC) Series
Data/Signal Line Protection — Product Selection Guide
Find your application in the left column.
DIN Rail Protection
Then look across for the appropriate product.
The Edco™ DRS (DC) Series is a DIN rail mountable, single-pair surge suppression
module implementing three-stage hybrid technology. This module addresses
over-voltage transients with gas tubes and silicon avalanche components. In
addition, sneak currents are mitigated with resettable fuses (PTCs). The PTCs
PRODUCTS
APPLICATIONS
Edco™
DRS
Series
Edco™
PC642
Series
Edco™
PHC
Series
Edco™
RJA/RJD
Series
Edco™
RM-CAT6
Series
increase resistance several orders of magnitude when over-currents exceed
Edco™
SLAC
Series
Edco™
SS64/65
Series
Edco™
CX
Series
safe levels. A normal state resumes when over-currents are removed. The ability
Edco™
RM-CX06
Series
to self-restore in this manner significantly increases suppressor performance
and survivability.
The Edco™ DRS (DC) Series mounts onto a standard 35 mm industrial DIN rail. There
Transmitters
are three “Field Side” and three “Electronics Side” screw terminals. One is reserved
for a shield. Three electrically tied ground terminals are provided for grounding the
Edco™ DRS Series unit to Building-Approved Ground. Shield is isolated from ground.
Telephone
For a 2-terminal version without a shield, order the Edco™ DRS-XXX-2.
Features
Industrial
Communications
Signaling
Circuits
Programmable
Logic Controllers
(I/O) Circuits
Control Panels
(Low Voltage)
Communication
Rack Equipment
■ Low-voltage data surge protection
■ Easy installation
■ Three-stage hybrid protection
■ Fits standard 35 mm DIN rail
■ Sneak/fault current protection with
resettable fuses — PTCs
■ Fast response time
< 1 nanosecond
■ Low profile packaging
■ 5 year warranty
■ UL 497B listed
General Technical Specifications
Part
Number
Maximum
Peak Signal
Voltage
Nominal
Breakdown
Voltage
Surge
1p 10 x 1000 µs
Current
Peak Current
8 x 20 µs
Waveform
Typ
Cap
(pf)
Maximum
Continuous
Current (ma)
Nominal
Series
Resistance
DRS-036
30
36
>100
10 kA
1500
150
5 Ohms
**DRS-130
170
200
>10
8 kA
1500
5000
None
Dimensional Diagrams
**Warning!! DRS-130RMS is for Discrete Signal
Use Only. Do not use DRS-130RMS on 120
VAC Power Lines. This unit is a non-hybrid,
MOV design, rated above 5 A operational
current and can withstand greater than eight
occurrences of a 10 kA 8 x 20 µs waveform, and
greater than 1000 occurrences of a 200 A 10 x
1000 µs waveform.
Video Equipment
Video Rack
Equipment
Water/
Wastewater
Instrumentation
DRS-XXX
DRS-XXX-2
(2 terminal version)
12
13
Data/Signal Line Protection
Data/Signal Line Protection
Edco™ DRS (DC) Series
Data/Signal Line Protection — Product Selection Guide
Find your application in the left column.
DIN Rail Protection
Then look across for the appropriate product.
The Edco™ DRS (DC) Series is a DIN rail mountable, single-pair surge suppression
module implementing three-stage hybrid technology. This module addresses
over-voltage transients with gas tubes and silicon avalanche components. In
addition, sneak currents are mitigated with resettable fuses (PTCs). The PTCs
PRODUCTS
APPLICATIONS
Edco™
DRS
Series
Edco™
PC642
Series
Edco™
PHC
Series
Edco™
RJA/RJD
Series
Edco™
RM-CAT6
Series
increase resistance several orders of magnitude when over-currents exceed
Edco™
SLAC
Series
Edco™
SS64/65
Series
Edco™
CX
Series
safe levels. A normal state resumes when over-currents are removed. The ability
Edco™
RM-CX06
Series
to self-restore in this manner significantly increases suppressor performance
and survivability.
The Edco™ DRS (DC) Series mounts onto a standard 35 mm industrial DIN rail. There
Transmitters
are three “Field Side” and three “Electronics Side” screw terminals. One is reserved
for a shield. Three electrically tied ground terminals are provided for grounding the
Edco™ DRS Series unit to Building-Approved Ground. Shield is isolated from ground.
Telephone
For a 2-terminal version without a shield, order the Edco™ DRS-XXX-2.
Features
Industrial
Communications
Signaling
Circuits
Programmable
Logic Controllers
(I/O) Circuits
Control Panels
(Low Voltage)
Communication
Rack Equipment
■ Low-voltage data surge protection
■ Easy installation
■ Three-stage hybrid protection
■ Fits standard 35 mm DIN rail
■ Sneak/fault current protection with
resettable fuses — PTCs
■ Fast response time
< 1 nanosecond
■ Low profile packaging
■ 5 year warranty
■ UL 497B listed
General Technical Specifications
Part
Number
Maximum
Peak Signal
Voltage
Nominal
Breakdown
Voltage
Surge
1p 10 x 1000 µs
Current
Peak Current
8 x 20 µs
Waveform
Typ
Cap
(pf)
Maximum
Continuous
Current (ma)
Nominal
Series
Resistance
DRS-036
30
36
>100
10 kA
1500
150
5 Ohms
**DRS-130
170
200
>10
8 kA
1500
5000
None
Dimensional Diagrams
**Warning!! DRS-130RMS is for Discrete Signal
Use Only. Do not use DRS-130RMS on 120
VAC Power Lines. This unit is a non-hybrid,
MOV design, rated above 5 A operational
current and can withstand greater than eight
occurrences of a 10 kA 8 x 20 µs waveform, and
greater than 1000 occurrences of a 200 A 10 x
1000 µs waveform.
Video Equipment
Video Rack
Equipment
Water/
Wastewater
Instrumentation
DRS-XXX
DRS-XXX-2
(2 terminal version)
12
13
Data/Signal Line Protection
Filtering/Line Conditioning
Edco™ PC642 Series
Islatrol™ — RM Series
Zone/Loop/Data
120 VAC Rackmount
The Edco™ PC642 Series surge suppressor is a two-pair (four-wire) module
Islatrol™ RM Series AC rackmount surge protector is ideal for protecting the
implementing three-stage hybrid technology. This module addresses
power feeding valuable rack equipment. Status LEDs indicate the correct power
over-voltage transients with gas tubes and silicon avalanche components. In
is coming to the unit, whether the unit is properly grounded and whether the
addition, sneak and fault currents are mitigated with resettable fuses (PTCs).
surge components are still intact. Units are available with a digital meter,
The PTCs increase resistance several orders of magnitude when over-currents
mounted on the front of the unit, which will monitor the voltage, current and
Model shown: RM-115-10 RM
power of the protected equipment.
exceed safe levels. A normal state resumes when over-currents are removed.
The ability to self-restore in this manner significantly increases suppressor
EDCO PCB1B-WKEY BASE SOLD SEPARATELY
performance and survivability.
The Edco™ PC642 card edge module is gold-plated, double-sided, and is
designed to mate with the Edco™ PCB1B-WKEY gold-plated female terminal
connector. When snapped together, the data circuits “pass thru” the protector
Features
in a serial fashion from the four “Field Side” terminals to the four “Electronics
■ 40 kA surge protection
■ Digital meter
Side” terminals. Terminals 1 or 10 of the Edco™ PCB1B-WKEY must be attached
■ 60 dB max noise filtering
■ Optional twist lock plug
to Building-Approved Ground per Edco™ Technical Bulletin # 2015.
■ 15 & 20 A models available
■ 1 year warranty
■ Power, ground and surge status indicators
Features
■ Three-stage hybrid protection
■ Fast response time
■ Sneak/fault current protection
■ Requires Edco ™ PCB1B-WKEY base
■ Resettable fusing — PTCs
■ PC642PTU (Pass Thru Unit)
available for troubleshooting
■ Low capacitance option
■ 5 year warranty
■ Plug-in module
General Technical Specifications
Maximum Continuous
Operating Voltage (MCOV)
5-250 VDC
Clamping Voltage
8-300 VDC
Operating Current
150mA
Peak Surge Current
Operating Temperature
Dimensions (Inches)
Weight
Certifications
-40°C to +85°C
2H x 1W x 2.5L
(PC642 + Mounting Base)
14
PC642C-008LC
RS423, Token Ring:
PC642C-008LC
RS232:
PC642C-036LC
DO NOT daisy chain grounds.
NOT intended for shield termination.
Install ground in accordance with
all applicable codes.
Amperage
Plug (NEMA)
Receptacles (NEMA)
Digital Meter
Locking Plug
120 V
15 A
5-15P
5-15R
Yes
No
RM-120-10RM
120 V
20 A
5-20P
5-20R
Yes
No
PC642C-030LC-036LC
ANSI/UL 1449 Third Edition
VPR
PC642C-036LC
Rated Voltage
24 VAC Power
PC642C-043LC
Rated Current
Peak Surge Current
Response Time
EMI/RFI Filtering
How to Specify the Appropriate Model
PC642CLow Capacitance,
LC Line to Line, Line to Ground
D Line to Line protection only
1 oz
Line to Ground
008
036
043
200
Max Operating
Voltage
Clamping
Voltage
(1000V@1mA)
5 VDC
30 VDC
36 VDC
43-250 VDC
8 VDC
36 VDC
43 VDC
300 VDC
008, 036, 043 models
only
008, 043 models only
200 models only
Output Receptacles
15A Models
Rackmount AC Power Protection
4–20ma:
-WKEY
UL 497B
Caution: The hybrid design of this product includes
series resistance. Do not place this product in
service on any signal line capable of supplying
more than 150 milliamperes continuously.
RS485, RS422:
E-NET, 10 BASE T:
GDT, SAD, w/Series PTC
Terminal block
w/compression lugs
Terminals accept up to 10 AWG
Voltage
RM-115-10RM
APPLICATION:
-WKEY
< 0.1 dB at 20 MHz
SPD Technology
Model
Ordering Information
0 to 20 MHz
Insertion Loss
Connection Type
Terminal Assignments
10 kA (8 x 20 µs)
Frequency Range
General Technical Specifications
LED Indicators
Digital Meter
(Optional)
Input Power
15 A Models
20A Models
L-N:400 V, L-G:500V, N-G:400V
120 V
15 A & 20 A
20 kA/mode, 40 kA/phase
<5 ns
60 dB Max
Green-Power on
Green-Ground OK
Green-Surge Circuit OK
20A Models
Thermal Protection
Overcurrent Protection
Dimensions
Certifications
Warranty
Front- (2) NEMA 5-15R
Back- (10) NEMA 5-15R
Front- (2) NEMA 5-20R
Back- (10) NEMA 5-20R
Thermal Protected MOVs
Circuit
1.75"H x 19"W x 3.8"D (1U)
ANSI/UL 1449 Third Edition Type 3
1 Year
Voltage Amps, Watts, VA, Hz, PF,
Kwh, and Clock
SJT 14/3C Power Cord (9 ft)
with NEMA 5-15P Plug
SJT 12/3C Power Cord (9 ft)
with NEMA 5-20P Plug
NEMA L5-20P Plug- Optional
11
Filtering/Line Conditioning
Data/Signal Line Protection
Edco™ PHC Series
Islatrol™ — SP-6TVN
Two-Pair Signaling Circuit Protector (Modular)
Industrial Strength Surge Suppression (Series)
The Edco™ PHC Series is designed to protect two pairs of wires specifically for
The Islatrol™ SP-6TVN plug-in unit is an Active Tracking Filter™ which plugs into
alarm and security systems where operating currents can be as high as 5 Amps.
a standard duplex receptacle. It features uniquely designed repositionable
Electrically, the Edco™ PHC Series is a rugged series hybrid implementing a
outlets for easy installation behind desks and other furniture. It protects
staged complement of MOVs, copper wound inductors and Silicon Avalanche
sensitive home or office equipment from damaging power disturbances
Diodes. This design reduces series resistance to 0.2 Ohms per pair. These
traveling through wiring to electrical outlets.
products are intended to mate with an Edco PCB1B-WKEY gold-plated female
terminal connector.
The Edco™ PHC modules plug into a base assembly (Edco™ PCB1B-WKEY). The
base assembly can be mounted to any flat surface and should be located as close
Features
Repositionable Outlets
as practical to the protected equipment. Terminal 1 and/or terminal 10 should
■ Plugs into standard 120 V, 15 Amp
electrical outlet
■ Perfect for tight spaces, behind furniture
and appliances
■ Total peak surge current capacity of
39,000 Amps
■ Intelligent monitoring against improper
wiring/grounding
■ Cables for telephone, video, and
data connections
■ 60 dB maximum high frequency
■ Three-stage protection
■ Continuous current up to 5 Amps
■ Operational indicator lamp
■ Differential protection
■ UL 497B listed
■ 5 year limited warranty
■ Common mode protection
■ Requires Edco ™ PCB1B-WKEY base
■ Plug-in module
■ PC642PTU (Pass Thru Unit)
available for troubleshooting
■ Repositionable outlets rotate to
accommodate available space
be connected to Building-Approved Ground with 12 or 10 gauge solid wire.
Features
EDCO PCB1B-WKEY BASE SOLD SEPARATELY
■ Automatic recovery
General Technical Specifications
■ Fast response time
AC Power Protection
VPR
L-N:330V, L-G:400V, N-G:400V
Nominal Operating Voltage
120 VAC, Single Phase
Operating Voltage Range
120 VAC +/- 10%
Operating Frequency Range
47 — 63 Hz
Rated Output (Amps)
15 Amperes
ANSI/IEEE C62.41 Category
Connection Type
265 V
Common Mode
290 V
ANSI/IEEE C62.41 Cat B Ringwave (6 kV, 500 A, 100 kHz)
Normal Mode
275 V
Common Mode
290 V
Category A & B
(6) 5-15R Receptacles and
5-15P Plug
Phase Configuration
2 Wire + Gnd
Size
High Impact Plastic
Weight
Common Mode
L — N, L — G, N — G
Indication of Suppression Status
Status Indicator
Response Time
Warranty
Maximum Continuous Operating Voltage (MCOV)
Line to Neutral
5 Year
Connection Type
Cables Provided
Peak Surge Current
Capacitance
Protection Level
130 VAC
Clamping Voltage (DC)
Attenuation
Peak Surge Current (8 x 20 ms)
Line to Neutral
13,000 Amps
Line to Ground
13,000 Amps
Neutral to Ground
13,000 Amps
Total
39,000 Amps
36-70 VDC
Clamping Voltage
43-100 VDC
Operating Current
40 dB Maximum, forward/reverse, 5 MHz to 50 MHz
Video 1 & 2
Phone
Network
Type “F”
Type RJ-11
Type RJ-45
6' (2x) Type “F”
6' Ends
6' RJ-11 Male
6' Ends
6' RJ-45 Male
Ends
5 kA
(8 x 20 µs)
2 kA
(10 x 1000 µs)
3 kA
(8 x 20 µs)
<12 pf
<50 pf
<70 pf
L-G
T-R, T-G, R-G
L-G (8 Lines)
145 V
270-350 V
30 V
1 dB @ 2 Ghz
N/A
N/A
-WKEY
Ordering Information
How to Specify the Appropriate Model
5A
Peak Surge Current
10 kA (8 x 20 µs)
0 to 10 MHz
Insertion Loss
< 0.1 dB at 10 MHz
SPD Technology
Low Voltage Protection
< .5 ns Normal Mode
ANSI/UL 1449 Third Edition Type 3
Operating Voltage
Connection Type
2.0 lbs (0.9 kgs)
Modes Of Protection
10
60 dB Maximum, forward/reverse, 100 kHz to 50 MHz
Terminal Assignments
General Technical Specifications
Frequency Range
Frequency Response
Normal Mode
7.5 x 4.75 x 1.75 (Inches)
Enclosure
Certifications
ANSI/IEEE C62.41 Cat A Ringwave (6 kV, 200 A, 100 kHz)
Normal Mode
■ 5 year warranty
MOV, SAD, w/Series Inductor
Terminal block
w/compression lugs
Terminals accept up to 10 AWG
Operating Temperature
Dimensions (Inches)
-40°C to +85°C
3.7H x 1.75W x 2.375L
(PHC + Mounting Base)
Weight
DO NOT daisy chain grounds. NOT intended for shield
termination. Install ground in accordance with all
applicable codes.
Dimensions
8 oz
Certifications
UL 497B
Applications Part Number
24V Horn, Strobe, Bell:
70V Speaker Lines:
PHC-043 & PCB1B-WKEY
PHC-SP70 & PCB1B-WKEY
-WKEY
15
Data/Signal Line Protection
Filtering/Line Conditioning
Islatrol™ IC+/LRIC+ Series
Active Tracking Filter™
Edco RJA-RJD Series
™
RJ-45 Telephone/Data
Ordering Information
Dimensional Diagram
The Edco RJA and Edco RJD Series are four pair telephone/data line
™
™
120 VAC Models with barrier strip at input and output/with wire leads at input and output (WL)
protectors that implement advanced two stage hybrid design. These units
B
A
F
address over-voltage transients with silicon breakover devices, while sneak
and fault currents are mitigated with PTC technology, which consists of solid
C
state resettable fuses.
The Edco™ RJA and Edco™ RJD Series incorporate RJ-45 female jacks in and out.
M
DIMOUN
EN TING
SIO
NS
D
The Edco™ RJA voltage clamp is set for C.O. Trunks and Analog Telephone
G
E
Model
Rated
Output
(Amps)
Case
Dimensions (In)
AxBxC
Mounting Flange
Dimensions (In)
DxExFxG
Screw
Size
Weight
(lbs)
IC+102 / IC+102WL
2.5
4 x 2.88 x 1.81
4.38 x 2.12 x 5.31 x 0.19
#6
1.0
IC+105 / IC+105WL
5.0
4 x 2.88 x 1.81
4.38 x 2.12 x 5.31 x 0.19
#6
1.3
IC+107 / IC+107WL
7.5
4.75 x 4.75 x 2.35
5.25 x 3.50 x 6.25 x 0.19
#6
2.0
IC+115 / IC+115WL
15
6.25 x 4.75 x 2.35
6.75 x 3.50 x 7.75 x 0.19
#8
3.5
IC+130 / IC+130WL
30
7.75 x 4.75 x 2.35
8.25 x 3.50 x 9.00 x 0.19
#8
6.0
Extensions (with ring in voltage), and the Edco™ RJD voltage clamp is set for
120 VAC Models with 5 foot line cord and single NEMA 5-15 receptacle
Digital Extensions (no ring in voltage).
Features
■ <1 nanosecond response time
■ Tip and ring to ground protection
■ Solid-state resettable fuses-PTCs
■ CAN/CSA C22.2, No. 226-92 Compliant
■ Silicon breakover technology
■ Low capacitance
■ 4 pair protection
■ Line-to-line protection
■ 5 year warranty
Case
Dimensions (In)
AxBxC
Mounting Flange
Dimensions (In)
DxExFxG
Screw
Size
Weight
(lbs)
LRIC+102
2.5
4.5 x 3.0 x 1.88
N/A
N/A
1.3
LRIC+105
5.0
4.5 x 4.5 x 2.38
N/A
N/A
2.0
LRIC+107
7.5
6.0 x 4.5 x 2.38
N/A
N/A
2.3
LRIC+115
15
7.5 x 4.5 x 2.38
N/A
N/A
4.0
240 VAC Models with barrier strip at input and output/with wire leads at input and output (WL)
B
■ UL 497A listed
Model
Rated
Output
(Amps)
A
F
C
D
M
DIMOUN
EN TING
SIO
NS
G
E
Model
Rated
Output
(Amps)
Case
Dimensions (In)
AxBxC
Mounting Flange
Dimensions (In)
DxExFxG
Screw Weight
Size
(lbs)
IC+202 / IC+202WL
2.5
4 x 2.88 x 1.81
4.38 x 2.12 x 5.31 x 0.19
#6
1.3
IC+205 / IC+205WL
5.0
4.75 x 4.75 x 2.35
5.25 x 3.50 x 6.25 x 0.19
#6
2.0
IC+207 / IC+207WL
7.5
6.25 x 4.75 x 2.35
6.75 x 3.50 x 7.75 x 0.19
#8
3.3
IC+215 / IC+215WL
15
7.75 x 4.75 x 2.35
8.25 x 3.50 x 9.00 x 0.19
#8
5.8
IC+230 / IC+230WL
30
7.75 x 4.75 x 2.35
8.25 x 3.50 x 9.00 x 0.19
#8
6.0
Islatrol™ Active Tracking Filters™ carry a 10 year warranty
General Technical Specifications
Ordering Information
Operating Voltage
48, 220 VDC
Analog Phone
RJA-45
Clamping Voltage
55, 280 VDC
Digital Phone
RJD-45
Operating Current
0.15 A
Peak Surge Current
Frequency Range
Insertion Loss
SPD Technology
Connection Type
Operating Temperature
Dimensions (Inches)
Weight
Certifications
16
Installation
200 A (10 x 1000 µs)
0 to 50 MHz
< 0.1 dB at 50 MHz
Silicon Breakover
Devices w/Series PTC
RJ-45 Jacks
-40°C to +85°C
1.0H x 2.5W x 4.25L
3 oz
UL 497A, CUL,
The Edco™ RJA and Edco™
RJD Series are intended
for indoor use only
and shall be employed
on the equipment side of
a listed primary
telephone protector.
9
Filtering/Line Conditioning
Data/Signal Line Protection
Edco™ RM-CAT6-POE Series
CAT6-POE Channel Rackmount
Islatrol IC+/LRIC+ Series
™
The Edco™ RM-CAT6-POE Series is a multi-channel high-speed data line protector
Active Tracking Filter™
that utilizes a three-stage hybrid design technology. This unit addresses high-
Series connected high-frequency noise filter with transient protection. Offers
energy voltage transients that can damage expensive computer equipment. Ideal
the flexibility of either receptacle/line cord connection or hard-wired connection
for network switches and hubs, the Edco™ RM-CAT6-POE Series is easily mounted
to critical loads (up to 30 Amperes). Applications include industrial or office
in close proximity to the protected equipment.
equipment, computers placed in harsh environments.
Features
■ Low insertion loss
■ Exceeds category 6 transmission values
■ Three stage hybrid
■ Compact 1U rack size
■ 1 year warranty
■ Meets Power-Over-Ethernet (POE)
requirements
■ Replaceable surge modules
Features
■ Typically reduces normal mode transients
to +/-2 volts
■ Surge current capacity — 45,000 Amps
■ LED power indication
■ 10 year warranty
■ Transient protection in all modes: line
to neutral, line to ground, and neutral
to ground
General Technical Specifications
Operating Voltage
57 V
Clamping Voltage
68 V
Transmission Speed
MCOV
Typical Category A Ringwave (6 kV, 200 A, 100 kHz)
120 Volt
150 VRMS
Model
Normal
275 VRMS
IC+102 / LRIC+102
1.0 / 0.9
302 / 287
Line Frequency
47 - 63 Hz
IC+105 / LRIC+105
0.7 / 0.8
292 / 307
IC+107 / LRIC+107
0.7 / 0.7
302 / 293
Response Time
Normal Mode
< 0.5 ns
Common Mode
< 5 ns
Operating Temperature
-40°C to +45°C at Full Load
Derate Linearly to 60% at +70ºC
0% to 95%
Operating Humidity
System Design
Common
240 Volt
IC+115 / LRIC+115
0.7 / 0.7
304 / 306
IC+130 / IC+202
0.5 / 1.1
306 / 536
IC+205 / IC+207
1.5 / 0.8
628 / 616
IC+215 / IC+230
0.6 / 0.9
572 / 566
Typical Category B Ringwave (6 kV, 500 A, 100 kHz)
10 Mbps,
100 Mbps, 1,000 Mbps
Operating Current
0.15 A
Connection Means
2-Port Series
SPD Technology
GDT, SAD, W/Series PTC
Series Blocking Inductors
voltage blocking current
smoothing inductors
Shunt Absorbing Components
sine wave tracking circuitry
Modes of Protection
Signal High-Low,
Signal High-Ground,
Signal Low-Ground
Peak Surge Current
Mounting
Dimensions
10 kA (8 x 20 µs)
Insertion Loss
<0.1 dB
VSWR
<1.2
Operating Humidity
Painted Steel
1.75Hx19Wx6.3D
Weight
5.5 lbs
Warranty
1 Year
Ordering Information
0-95% Non-Condensing
Operating Temperature
Rackmount
Enclosure Type
-40°C to +85°C
RM-CAT6-8POE
8 Channels
Input Connection Type
RJ-45
RM-CAT6-16POE
16 Channels
Output Connection Type
RJ-45
RM-CAT6-24POE
24 Channels
RM-CAT6-48POE
48 Channels
Edco™ CX-HFN Series
MOV Transient Protection
high-energy transient
protection line to neutral,
line to ground,
neutral to ground
High Frequency Coax Protector — N-Type
The Edco™ CX-HFN surge protectors are designed to protect sensitive electronic
Model
Normal
Common
Peak Surge Current Capability (8 x 20 µs)
IC+102 / LRIC+102
178 / 188
302 / 285
Line to Neutral
15,000 Amps
IC+105 / LRIC+105
162 / 191
291 / 300
Line to Ground
15,000 Amps
IC+107 / LRIC+107
173 / 190
300 / 298
Neutral to Ground
15,000 Amps
IC+115 / LRIC+115
153 / 149
307 / 309
IC+130 / IC+202
241 / 302
299 / 532
also has a replaceable protection cartridge (CX-RC). The Edco™ CX-HFN
Load Surge Current Rating
equipment from damage due to excessive voltage or currents generated by
Pulse Capacitor
high-frequency noise absorption
lightning or static build-up.
The Edco™ CX-HFN offers low signal loss at frequencies up to 4 gigahertz. The unit
10 mSec
5 x Nominal
IC+205 / IC+207
378 / 336
594 / 596
accommodates both bulkhead mount and stud mount. The input and output
1 sec
3 x Nominal
IC+215 / IC+230
272 / 342
548 / 578
10 sec
2 x Nominal
connections are interchangeable.
Packaging
• High Impact Plastic Case
• Vacuum Impregnated Magnetics
• Epoxy Encapsulated
Frequency Response (Forward-Reverse)
Normal Mode
■ Low signal loss
Connection Diagram
■ 5 year warranty
General Technical Specifications
Ordering Information
TM
100 kHz to 50 MHz - 90 dB Min
5 MHz to 50 MHz - 60 dB Min
Features
Note: All measurements in volts. IEEE test results with
no AC applied. Normal mode—L1-N or L1-L2;
Common mode—L-G, N-G or L1-G, L2-G.
TM
Common Mode
Operating Voltage
130 VDC
Insertion Loss
Clamping Voltage
(DC Spark Over Voltage)
150 VDC
SPD Technology
Operating Current
Peak Surge Current
1A
10 kA (8 x 20 µs)
Maximum Power
10 Watts
Impedence
50 Ohms
Frequency Range
10
■ Up to 48 channels available
■ UL 1283, CSA recognized
< 0.3 dB to 0.5 dB 2 to 3 GHz
Gas Discharge Tube (GDT)
Connection Type
Female N-Type
Operating Temperature
-30°C to +85°C
Dimensions (Inches)
Weight
CX-HFN-FF (Female–Female)
CX-HFN-FM (Female-Male)
1.25H x .875W x 2.5L
4 oz
0 to 4 GHz
17
Data/Signal Line Protection
Filtering/Line Conditioning
Edco™ SLAC Series
Islatrol™ IE Series
AC Power/Signal
Active Tracking Filter™
The Edco SLAC Series suppressor is specifically designed to protect electronic
™
instruments used by the water/wastewater industries. It combines hybrid AC
power protection and signal line protection in a NEMA-4X polycarbonate case.
System Design
The AC power suppressor can supply up to 1875 Watts and has a 15 Amp
replaceable fuse to prevent overloading of the protective elements. A “Power
ON” LED provides visual indication that power is applied to instruments. Signal
line protection is accomplished by the Edco™ PC642 Series available in a variety
of voltage clamps. Signal current can be monitored by reading the voltage
Shunt Absorbing Components
line side sine wave tracking circuitry
Shunt Absorbing Components
load side sine wave tracking circuitry
across the 10 V, 1% resistors (TP1 & TP2 or TP3 & TP4). All leads going to the
Edco™ SLAC board are terminated by quick disconnect or barrier block
Finger Safe Terminals
IEC 998 approved terminals
connectors to facilitate easy removal for service or replacement.
Form C Relay Contacts
normally open and normally closed dry
contact for remote status monitoring
Features
■ Optional twist lock plug lightning & surge
suppression for AC power and low-voltage
signal lines
■ Test jacks for signal line monitoring
■ Series hybrid AC suppressor/filter
■ Optional stainless steel or fiberglass
enclosure
■ Plug-in protection module
■ 15 Amp replaceable fuse
General Technical Specifications
AC Power
Technology
Three-Stage Series Hybrid
Input Voltage
15 Amps Max.
Response Time
<5 Nanoseconds
Maximum Surge Current (8x20 µs)
Normal Mode
(L-N)
■ 5 year warranty
MOV Array
high-energy surge current diversion
array providing transient protection
line to neutral, line to ground, and
neutral to ground
Silicon Avalanche Diodes
fast responding surge current
diversion components
■ ANSI/UL 1449 Third Edition
Optional Enclosure
Glass-Filled Polycarbonate Base
Cover Molded in Clear Polycarbonate
Series Blocking Inductor
voltage blocking current
soothing inductor
Pulse Capacitor
high-frequency noise absorption
DIN Rail Mountable
mounts to standard 35 mm
industrial DIN rail; rotates 90°
for mounting flexibility
Knockouts for 1/2" and 3/4" hubs
10 kA
Occurrences at 500 Amps
■ “Power ON” indicator
NEMA-4X
120 VAC 50/60 Hz
Output Current
Parameter
Standard Enclosure
Unit Status Indicator
green LED monitors the operational
status of the Elite Series
Bosses for 6 BZ x 3/8" Self-Tapping Screws
>50
Maximum Protection—Total Insulation
Common Mode
(L-G) (N-G)
Corrosion Resistant
Resists Temperature of 248°F
IEEE 587 CAT A Ring*
172 V
280 V
Flammability Rating UL94-5V
IEEE 587 CAT B Ring*
205 V
280 V
IEEE 587 CAT B Impulse* 330 V
360 V
Nominal Outside dimensions (Inches)
How to Specify the Appropriate Model
H= 6.89, W=6.89, D=2.95
Connection Diagram
*Measured from zero volts, 90° Phase angle
General Technical Specifications
Signal Line
Signal Protector Technology
AC Protector Technology
Peak Surge Current
Response Time
Voltage Clamp (customer selected)
Series Resistance
18
GDT, PTC, SAD
MOV, Fuse
10 kA
Ordering Information
These blocks are for PC642
VoltageSelection if applicable. See
PC 642 Datasheet for additional
information. 0 3 6 L C is standard
for 4-20 mA Signal Line.
<1 Nanosecond
8–200 Volts
5 ! (Typical)
7
Filtering/Line Conditioning
Data/Signal Line Protection
Islatrol™ IE Series
Edco™ SS64 & SS65 Series
Active Tracking Filter™
Wastewater/Industrial Applications
The Islatrol IE is a series-connected DIN or flange mounted high-
The Edco™ SS64 and Edco™ SS65 Series suppressors are designed for the water
frequency noise filter and surge suppressor. Its ideal applications include
and wastewater industry. These multi-stage hybrid suppressors address
critical industrial loads drawing up to 20 Amps of continuous current,
over-voltage transients with gas tube and silicon avalanche technology. In
while typical applications include any microprocessor-based products,
addition, sneak and fault currents are mitigated with PTC devices which
including industrial PLCs, OEM applications, and motion control systems.
consist of solid-state resettable fuses. The units are encapsulated in stainless
™
steel pipe nipples making them suitable for use in severe environments. The
Edco™ SS64 models protect a signal pair and the Edco™ SS65 models protect a
Features
■ Multi-staged design, combining a unique
hybrid clamping network with the active
tracking technology of the Islatrol ® family
■ Surge current capacity — 45,000 Amps
■ Transient protection in all modes: line
to neutral, line to ground, and neutral
to ground
signal pair plus the cable shield (drain wire).
■ LED status indication and form C contact
for remote indication
■ DIN mountable enclosure
■ ANSI/UL 1449 Third Edition Type 4,
1283, CUL recognized, CE
Features
■ 10 year warranty
■ Transient protection for
low-voltage signal lines
■ Encapsulated in stainless steel
pipe nipples
■ Sneak/fault current protection
■ Protection for one pair
(Two wires & shield on SS65)
■ Resettable fusing—PTCs
Performance Technical Specifications General Technical Specifications
Ordering Information
Model
Voltage*
IE-103
IE-105
IE-110
IE-120
L-N
400V
400V
IE-203
IE-205
IE-210
IE-220
L-G
600V
600V
N-G
L-L
600V
N/A
500V
N/A
MCOV
700V
900V
700V
Peak Surge Current Capability (8 x 20 µs)
5 Amps
IE-105
120 V
10 Amps
IE-110
120 V
20 Amps
IE-120
Continuous Current
Model
275 VRMS
Line Frequency
47 - 63 Hz
Terminal
Mounting Type
DIN/Flange
Weight
< 3 lbs
Voltage*
3 Amps
IE-203
Response Time
Normal Mode
< 0.5 ns
240 V
5 Amps
IE-205
Maximum Signal Voltage
28 V Max
< 5 ns
240 V
10 Amps
IE-210
DC Clamping Level (L-G)
36 V ±l0%
-40°C to +45°C
240 V
20 Amps
IE-220
DC Clamping Level (L-L)
72 V ±l0%
Operating Temperature
Derate Linearly to 60% at +70ºC
Operating Humidity
* All voltage configurations are single phase - 2 wire + gnd.
Common Mode
100 kHz to 50 MHz - 90 dB Min
5 MHz to 50 MHz - 60 dB Min
Maximum let-thru Voltage:
Dimensional Diagram
Line-to-Line (10x700 µs)
Normal Mode/Common Mode
(Zero Volts Bias)
5 Amp
0.7 V/292 V
10 Amp
0.7 V/300 V
20 Amp
0.7 V/300 V
90 V @ 400 A
Series Resistance (per conductor)
Typical Category A Ringwave (6 kV, 200 A, 100 kHz)
1 V/300 V
44 V @ 400 A
Maximum let-thru Voltage:
Capacitance:
3 Amp
Typical Applications
< 1 Nanosecond
Line-to-Ground (10x700 µs)
0% to 95%
Frequency Response (Forward-Reverse)
Normal Mode
General Technical Specifications
240 V
Common Mode
■ 5 year warranty
■ Automatic recovery
Response Time
15,000 Amps
15,000 Amps
120 V
240 Volt
15,000 Amps
45,000 Amps
IE-103
120 V
Line to Ground
Total
Model
3 Amps
150 VRMS
Line to Neutral
Neutral to Ground
Continuous Current
120 Volt
Connection
1,000V
■ Differential and common mode protection
Number of Occurrences
5 V (typical)
(L-L) 600 pf typical
(L-G) 1200 pf typical
400 @ 500 Amps
(10x1000 µs)
Typical Category B Ringwave (6 kV, 500 A, 100 kHz)
Normal Mode/Common Mode
6
3 Amp
178 V/300 V
5 Amp
162 V/291 V
10 Amp
153 V/300 V
20 Amp
200 V/300 V
Caution: The hybrid design of this product includes series resistance. Do not place this product
in service on any signal lines capable of supplying more than 150 milliamperes continuously.
19
Data/Signal Line Protection
Filtering/Line Conditioning
Edco™ CX Series
CCTV & Data Applications/Coax
The Edco™ CX06-M & Edco™ CX06-MI Surge Protective Devices (SPDs)
implement three-stage hybrid technology. The SPDs address over-voltage
transients with a primary Gas Discharge Tube (GDT), and secondary Silicon
Avalanche Diode (SAD) components. Over-current protection, e.g. sneak and
Filtering/Line Conditioning — Product Selection Guide
Find your application in the left column.
Then look across for the appropriate product.
fault currents, are mitigated with solid-state resettable fuses — PTCs. The Edco™
CX06-M & Edco™ CX06-MI SPDs are designed in accordance with NFPA 780
PRODUCTS
(2004 edition) requirements, with up to 20 kA of surge current capability. The
Edco™ CX06-MI model has an isolated ground and is recommended for use at the
camera end.
APPLICATIONS
Features
■ Sneak/fault current protection
■ CX06-MI has an isolated ground
■ Low insertion loss
■ 5 year warranty
Islatrol™
IE
Series
Islatrol™
IC+/LRIC+
Series
Islatrol™
SP-6TVN
Series
Islatrol™
RM
Series
■ Shielded case
General Technical Specifications
Operating Voltage
Ordering Information
5 VDC
Connection Type
Clamping Voltage
6 VDC
Operating Temperature
Operating Current
0.15 A
Dimensions (Inches)
Peak Surge Current
Frequency Range
Insertion Loss
SPD Technology
20 kA (8 x 20 µs)
0 to 20MHz
< 0.1 dB at 20 MHz
Programmable Logic
Controllers
Weight
BNC, 50/75 Ohm
Head End
-40°C to +85°C
Camera End
CX06-MI
M = 1.5H x 1W x 3.25L
MI = 1.5H x 1W x 4L
Camera End
CX06-MI-SBL
M = 2.3 oz
Certifications
*
CX06-M
MI = 3 oz
UL 497B
Control Panels
(AC Power)
*
*
Various OEM
Equipment
*
*
GDT, SAD, w/Series PTC
Edco™ RM-CX06-16R
Channel Rackmount
The Edco™ RM-CX06-16R Surge Protective Device (SPD) is a 16 channel coax
SPD implementing three-stage hybrid technology. The SPD addresses overvoltage transients with a primary Gas Discharge Tube (GDT), and secondary
Silicon Avalanche Diode (SAD) components. Over-current protection, e.g.,
sneak and fault currents, are mitigated with new solid-state resettable fuses —
PTCs. The Edco™ RM-CX06-16R SPD is designed in accordance with NFPA 780
(2004 edition) requirements, with up to 20 kA of surge current capability.
Home
Entertainment/Office
*
Features
■ Sneak/fault current protection
■ 16 channel
■ Low insertion loss
■ 1 year warranty
■ Shielded case
AC Rack Equipment
General Technical Specifications
Operating Voltage
5 VDC
Frequency Range
Clamping Voltage
6 VDC
Insertion Loss
Operating Current
0.15 A
SPD Technology
Peak Surge Current
20
20 kA (8 x 20 µs)
Connection Type
0 to 100 MHz
< 0.1 dB at 20 MHz
GDT, SAD, w/Series PTC
BNC, 50/75 Ohm
Operating Temperature
Dimensions (Inches)
Weight
Certifications
-40°C to +85°C
1.75H x 19W x 2.0D (1U)
3.2 lbs
UL 497B
5
TVSS/Surge Protective Devices (SPDs)
Data/Signal Line Protection
Edco EMC-240B
120/240 VAC Low Exposure AC Panel Protection
Edco™ CAT6-5POE Series
The Edco EMC-240B surge suppressor is designed to protect AC distribution
panel circuits or 120V power supplies feeding sensitive electronic equipment.
CAT6/CAT5 Power Over Ethernet
Electrically, the unit incorporates MOV and thermal fusing technology. The Edco
The Edco™ CAT6-5POE Series is designed to work on Category 5 Power-Over-
EMC 240B is designed to be installed in parallel on standard single phase
Ethernet transmission lines as well as Category 6 applications. Ideal to protect
120VAC (L,N,G) circuits.
expensive equipment against surges and transients entering a building on
exposed transmission lines.
Features
■ Fast response time
■ Operational status indicators
■ 40,000 Amps per phase capacity
■ UL 1449 Third Edition, Type 2 listed
■ Failsafe and fused
■ 5 year warranty
General Technical Specifications
Operating Voltage
120/240 VAC
VPR
L-N:600V, L-L:1,200V
Fault Current Rating
42 kAIC
UL Location
Type 2
I-Nominal (kA)
Total Peak Surge Current
■ Applications up to 60 VDC @ 300 mA
■ Exceeds CAT5 & 6 transmission values
■ 1 year warranty
■ CAT5 POE compatible
Operating Frequency
47-63 Hz
EMI Attenuation (100 kHz to 100 MHz)
SPD Technology
> 40 dB
Metal Oxide Varistors (MOVs)
Modes of Protection
Line-to-Line,
Line-to-Neutral
3kA
Operating Current
Features
Operating Temperature
Dimensions (Inches)
-40°C to +85°C
Weight
Certifications
■ CAT6 compatible
4.6H x 2.2W x 2.8L
13.5 oz
ANSI/UL 1449 Third Edition
Type 2, CUL
General Technical Specifications
Ordering Information
NA, Parallel
Status Indication
Power On & MOVs functional
Operating Voltage
60 VDC
Connection Type
80 kA (8 x 20 µs)
Connection Type
Wire Leads
Clamping Voltage
65 VDC
Operating Temperature
Operating Current
300 mA
Dimensions (Inches)
Peak Surge Current
Edco FAS-120AC
™
Frequency Range
Insertion Loss
120 VAC Medium Exposure AC Panel Protection
SPD Technology
60A (10 x 1000 µs)
Weight
RJ-45 Jacks
RJ-45 (Female-Female)
CAT6-5POE-FF
-40°C to +85°C
0.8H x 1.0W x 2.3L
1 oz
0 to 250 MHz
< 0.1 dB at 20 MHz
Silicon Avalanche Diode (SAD)
The Edco FAS-120AC surge suppressor is designed to protect AC panel
circuits or 120V power supplies feeding sensitive electronic equipment.
Electrically the unit incorporates MOV and thermal fusing technology. This device is
designed to be installed in parallel on standard single phase 120VAC (L,N,G) circuits.
Installation can be close-nipple up to a distribution panel/circuit or hardwired
in parallel up to power supply input terminal screws. Be sure to dress leads as
short as possible.
Features
■ LED indicator
■ Compact size
■ Fast response time
■ Liquid tight conduit fitting
■ Thermal fuse
■ 5 year warranty
■ L-G, L-N, & N-G protection
General Technical Specifications
Operating Voltage
VPR
120 VAC
L-N:700V, L-G:700V, N-G:700V
UL Location
I-Nominal
Operating Current
Total Peak Surge Current
Operating Frequency
4
Type 2
3 kA
EMI Attenuation (100 kHz to 100 MHz)
SPD Technology
Modes of Protection
Line-to-Neutral,
Dimensions (Inches)
Weight
Certifications
2.5H x 1.5W x 3.0L
4.2 oz
ANSI/UL 1449 Third Edition
Line-to-Ground, Neutral-to-Ground
NA, Parallel
Status Indication
15.5 kA (8 x 20 µs)
Connection Type
47-63 Hz
> 25 dB
Metal Oxide Varistors (MOVs)
Power On & MOV Functional
Operating Temperature
Wire Leads
-40°C to +85°C
21
Technical Bulletins
TVSS/Surge Protective Devices (SPDs)
DRS Series
Technical Bulletins — High-Density Multiple Input Rack
The DRS is a modular surge protective device (SPD) that is designed for easy
installation in control panels using standard DIN rail mounting brackets. The DRS
devices offer both normal and common surge protection up to 40 kA per phase.
Features
■ Effectively handles high-energy transients
on TT, TN-C, TN-S and TN-C-S three-phase
power systems
■ SPD rated Type 2 in accordance with
EN 61643-11; Class I & II in accordance
with IEC 61643-1
■ Built-in thermal components disconnect
SPD from the power source to avoid
thermal runaway conditions
■ MOV only or MOV+Gas Tube models
available
■ Fast response time, high surge current
capability, low voltage protection levels
■ Visual inspection window on each module
indicates status
■ 3-pole terminal provides remote status
monitoring
■ DIN rail mounting and plug-in module
design allow for easy installation,
maintenance and replacement of
surge element
■ 5 year warranty
TM
How to Specify the Appropriate Model
Example: DRS 120 3 1 Q
Nominal Voltage
(Un) (XXX)
# of Metal Oxide Varistor Modules*
(X)
# of Gas Tube Modules**
(X)
120
0
0
230
1
1
240
2
277
3
346
4
TM
Q
*MOV modules are typically one module per phase and may be wired L-N, L-G or N-G.
**Gas Tube modules typically used in the N-G mode for type TT grounding systems.
***Certain applications require higher rated components in order to survive frequent
voltage rises, in this case order a unit with a “Q” at the end of the part number.
480
TM
Higher Rated Voltage***
(Optional)
Replacement modules available: Order DRS + Un + M (for MOV) or G (for Gas Tube)
TM
Performance Technical Specifications
DRS12031
TM
System Voltage
Type of Network
DRS27731
DRS34631
120/208,
230/400, 220/380, 277/480,
127/220 VAC
240/415 VAC 254/440 VAC
TT-TN
TT-TN
TT-TN
L-N; N-PE
L-N; N-PE
L-N; N-PE
Nominal Voltage
Un–120 V
Un–230 V
Un–277 V
Un–346 V
Rated Voltage
(MCOV)
Uc–150 V
Uc–320 V
Uc–320 V
Uc–420 V
1. SLAC UNIT PROVIDES ONE POWER AND TWO SIGNAL PROTECTION CIRCUITS.
Nominal Discharge
Current (8 x 20 µs)
1n–20 kA
2. SURGE DEVICES SHOULD BE GROUNDED LOCALLY WITH A GROUND ROD,
AND ALSO AT THE MAIN PANEL ELECTRICAL GROUND.
Maximum
Discharge Current
Imax–40 kA
3. CHECK WITH EMERSON NETWORK POWER SURGE PROTECTION, INC. TO
DETERMINE IF OUTPUT CAN BE SURGE PROTECTED.
TT-TN
346/600 VAC
Modes of Protection L-N; N-PE
NOTES:
1n–20 kA
Imax–40 kA
Up–1.6 kV
1n–20 kA
Imax–40 kA
Up—1.6 kV
1n–20 kA
Imax–40 kA
Up–1.2 kV
Response Time
TS–25 ns
TS–25 ns
TS–25 ns
TS–25 ns
95%
95%
95%
95%
> 103 MV
> 103 MV
> 103 MV
> 103 MV
Isolation
Resistance
Test Standards
EN 61643-11
Type 2
IEC61643- 1:1998-02
Class II
Mechanical
Characteristics
Dimensions (Length x Width x Height)
70.8mm x 90.5mm x 68mm
I/O Connections
By Screw Terminal: 4-25 mm2
By Connection Bus
MOV Encapsulation Material
Disconnection Indicator
Voltage Protection
Level
Relative Humidity
22
DRS23031
Electrical
Characteristics
Up–2.0 kV
Status Monitoring
Mounting
Operation Temperature Range
Degree of Protection
Disconnection Device
Housing Material
Epoxy Resin
Mechanical Indicator
Remote Alarm Terminals
Symmetrical Rail (EN50022/DIN46277-3)
-40°C to +85°C
IP 20
Thermal Cutoff System
ABS/PA UL94V0
3
Technical Bulletins
TVSS/Surge Protective Devices (SPDs)
TVSS/SPDs — Product Selection Guide
Technical Bulletins — Surge Protection for the Water Industry
Find your application in the left column.
Then look across for the appropriate product (s).
PRODUCTS
APPLICATIONS
DRS
Series
TM
Edco
EMC
Series
Edco
FAS
Series
TM
Facility Service
Entrance
Distribution Panels
TM
TM
Sub-Distribution
Panels
Branch Panelboards
(Commercial)
TM
Branch Panelboards
(Residential)
Motor Control Centers
Control Panels
(AC Power)
NOTES:
1. SLAC UNIT PROVIDES ONE POWER AND TWO SIGNAL PROTECTION CIRCUITS.
Various OEM Equipment
2
2. SURGE DEVICES SHOULD BE GROUNDED LOCALLY WITH A GROUND ROD,
AND ALSO AT THE MAIN PANEL ELECTRICAL GROUND.
3. CHECK WITH EMERSON NETWORK POWER SURGE PROTECTION, INC. TO
DETERMINE IF OUTPUT CAN BE SURGE PROTECTED.
23
Table of Contents
Technical Bulletins — Surge Protection for Power and Signal Lines
Products
Page #
TVSS/SURGE PROTECTION DEVICES (SPDs)
TVSS/SPDs — Product Selection Guide
Emerson Network Power DRS Series
Edco EMC-240B — Low Exposure AC Panel Protection
Edco FAS-120AC — Medium Exposure AC Panel Protection
2
3
4
4
FILTERING/LINE CONDITIONING
TM
Filtering/Line Conditioning — Product Selection Guide
Islatrol™ IE Series — Active Tracking Filter™
Islatrol™ IC+/LRIC+ Series — Active Tracking Filter™
Islatrol™ — SP-6TVN — Industrial Strength Surge Suppression (Series)
Islatrol™ — RM Series — 120 VAC Rackmount
TM
5
6, 7
8, 9
10
11
DATA/SIGNAL LINE PROTECTION
TM
TM
Data/Signal Line Protection — Product Selection Guide
Edco™ DRS (DC) Series — DIN Rail Protection
Edco™ PC642 Series — Zone/Loop/Data
Edco™ PHC Series — Two-Pair Signaling Circuit Protector (Modular)
Edco™ RJA-RJD Series — RJ-45 Telephone/Data
Edco™ RM-CAT6-16POE — CAT6-16POE Channel Rackmount
Edco™ CX-HFN-FF/CX-HFN-FM — High Frequency Line Protector — N-Type
Edco™ SLAC Series — AC Power/Signal
Edco™ SS64 & SS65 Series — Wastewater/Industrial Applications
Edco™ CX Series — CCTV & Data Applications/Coax
Edco™ RM-CXO6-16R — Channel Rackmount
Edco™ CAT6-5 POE Series
TECHNICAL BULLETINS
High-Density Multiple Input Rack
Surge Protection for the Water Industry
Surge Protection for Power and Signal Lines
Note: Refer to EmersonNetworkPower.com/surge for most current product information.
NOTES:
1. SLAC UNIT PROVIDES ONE POWER AND TWO SIGNAL PROTECTION CIRCUITS.
2. SURGE DEVICES SHOULD BE GROUNDED LOCALLY WITH A GROUND ROD,
AND ALSO AT THE MAIN PANEL ELECTRICAL GROUND.
3. CHECK WITH EMERSON NETWORK POWER SURGE PROTECTION, INC. TO
DETERMINE IF OUTPUT CAN BE SURGE PROTECTED.
24
12
13
14
15
16
17
17
18
19
20
20
21
22
23
24
Power Quality Solutions for
ALL Your Application Needs
“Dirty” power is a problem. Whether it’s called a
surge, spike, transient or noise, “dirty” power is an abnormality in
the power that runs your facility. These power problems can leave
buildings in the dark and disable equipment, costing you thousands
in repairs and lost revenue. Your productivity uptime and reputation
depend on consistent power quality. Emerson Network Power Surge
Protection provides products and solutions that ensure reliability
from Grid to Chip. For more than 40 years, Facility Managers,
Engineers, and System Integrators have trusted Emerson Network
Power Surge Protection products to protect critical equipment in
the Industrial Process, Computing, Research/Testing and
Communications fields.
Emerson Network Power Surge Protection and the IEEE Standard
1100-1999 (Emerald Book) recommend a properly rated surge
protection device should be applied on ALL electrical conductors
entering your facility including: power, voice, and data. Without
proper protection – data disruption, hardware stress or destruction
could occur.
As a line of defense against damaging transients, Emerson Network
Power Surge Protection manufactures products in the following
categories:
■ Surge Protection Devices (SPDs) — which focus on
limiting high-voltage spikes to an acceptable level
■ Filtering/Line Conditioning — protect against low-energy
transients and high frequency noise and finally…
■ Data/Signal Line Protection — products guard sensitive
instrumentation against what we refer to as ‘backdoor’
transients and noise.
Why allow “dirty” power to put your equipment at risk? Turn
to Emerson Network Power Surge Protection products for
peace of mind. We provide solutions for all your application needs
and the foundation for Business-Critical Continuity™.
Power Switching & Controls
For Business-Critical ContinuityTM
Grid to Chip Surge Protection
Product Catalog
Contact
Surge Protection
100 Emerson Parkway
Binghamton, NY 13905
T: 607-721-8840 (Outside U.S.)
T: 800-288-6169 (U.S. & Canada Only)
F: 607-722-8713
E: [email protected]
Emerson Network Power.
The global leader in enabling Business-Critical ContinuityTM.
EmersonNetworkPower. com/surge
AC Power
Embedded Computing
Infrastructure Management & Monitoring
Thermal Management
Connectivity
DC Power
Embedded Power
Industrial Power
Outside Plant
Power Switching & Controls
Racks & Integrated Cabinents
Service
Business-Critical Continuity, Emerson Network Power and the Emerson Network Power logo are trademarks and service marks of Emerson Electric Co.
©2014 Emerson Electric Co.
While every precaution has been taken to ensure accuracy and completeness in this literature, Emerson Network Power assumes no responsibility, and disclaims all liability
for damages resulting from use of this information or for any errors or omissions.
SL-30900 Rev.3 1/14 Printed in USA