TI DS80PCI800SQ

DS80PCI800
www.ti.com
SNLS334E – APRIL 2011 – REVISED MARCH 2012
DS80PCI800 2.5 Gbps / 5.0 Gbps / 8.0 Gbps 8 Channel PCI Express
Repeater with Equalization and De-Emphasis
Check for Samples: DS80PCI800
FEATURES
1
•
2
•
•
•
•
Comprehensive family, proven system interoperability
– DS80PCI102 : x1 PCIe Gen-1/2/3
– DS80PCI402 : x4 PCIe Gen-1/2/3
– DS80PCI800 : x8/x16 PCIe Gen-1/2/3
Automatic rate detect and adaptation to Gen1/2/3 speeds
Seamless support for Gen-3 transmit FIR
handshake
Rate adaptive receive EQ (up to 36 dB),
transmit de-emphasis (up to 12 dB) only Gen1/2
Adjustable Transmit VOD: 0.8 to 1.3 Vp-p (pin
•
•
•
•
•
•
•
•
mode)
0.2 UI of residual deterministic jitter at 8 Gbps
after 40” of FR4 or 10m 30awg PCIe Cable
Low power dissipation with ability to turnoff
unused channels: 65 mW/channel
Automatic receiver detect (hot-plug)
Multiple configuration modes:
Pins/SMbus/Direct-EEPROM load
Flow-thru pinout: 54-pin LLP (10 mm x 5.5 mm,
0.5 mm pitch)
Single supply voltage: 2.5V or 3.3V (selectable)
3 kV HBM ESD rating
−40 to 85°C operating temperature range
DESCRIPTION
The DS80PCI800 is a low power, 8 channel repeater with 4-stage input equalization, and output de-emphasis
driver to enhance the reach of PCI express serial links in board-to-board or cable interconnects. Ideal for higher
density x8 and x16 PCI express configurations, the DS80PCI800 automatically detects and adapts to Gen-1,
Gen-2 and Gen-3 data rates for easy system upgrade.
Each channel supports seamless detection and management of the new Gen-3 transmit equalizer coefficients
(FIR tap) handshake protocol and PCIe control signals such as transmit idle, beacon etc. without external system
intervention. An automatic receive detection circuitry controls the input termination impedance based upon
endpoint insertion (hot-plug events). These features guarantee PCIe interoperability at both the electrical and
system level, while reducing design complexity.
Powered by National’s SiGe BiCMOS process, DS80PCI800 offers programmable transmit de-emphasis (up to
12 dB), transmit VOD (up to 1300 mVp-p) and receive equalization (up to 36 dB) to enable longer distance
transmission in lossy copper cables (10m+), or backplanes (40”+) with multiple connectors. The receiver is
capable of opening an input eye that is completely closed due to inter-symbol interference (ISI) introduced by the
interconnect medium.
The programmable settings can be applied easily via pins, software (SMBus/I2C) or loaded via an external
EEPROM. When operating in the EEPROM mode, the configuration information is automatically loaded on power
up, which eliminates the need for an external microprocessor or software driver.
With a low power consumption and control to turn-off unused channels, the DS80PCI800 is part of National's
PowerWise family of energy efficient devices.
1
2
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2011–2012, Texas Instruments Incorporated
DS80PCI800
SNLS334E – APRIL 2011 – REVISED MARCH 2012
www.ti.com
Typical Application
8
TX
Add-in Card
End Point
PCIe
Connector
8
RX
DS80PCI800
8
RX
System Board
Root Complex
DS80PCI800
PCIe
Connector
8
TX
ard
Bo ce
Tra
Block Diagram - Detail View Of Channel (1 Of 8)
VOD/DeEMPHASIS
CONTROL
VDD
Auto/Manual
RXDET
INx_n+
RATE
DET
DEMA/B
SMBus
EQ
OUTBUF
INx_n-
EQA/B
SMBus
2
OUTx_n+
OUTx_n-
IDLE
DET
TX Idle Enable
SMBus
Submit Documentation Feedback
Copyright © 2011–2012, Texas Instruments Incorporated
Product Folder Links: DS80PCI800
DS80PCI800
www.ti.com
SNLS334E – APRIL 2011 – REVISED MARCH 2012
VDD
DEMA1/SCL
DEMA0/SDA
ENSMB
EQB1/AD2
EQB0/AD3
50
49
48
47
46
PRSNT
51
DEMB0/AD1
53
52
DEMB1/AD0
54
Pin Diagram
SMBUS AND CONTROL
INB_0+
1
45
OUTB_0+
INB_0-
2
44
OUTB_0-
INB_1+
3
43
OUTB_1+
INB_1-
4
42
OUTB_1-
INB_2+
5
41
VDD
INB_2-
6
40
OUTB_2+
INB_3+
7
39
OUTB_2-
INB_3-
8
38
OUTB_3+
VDD
9
37
OUTB_3-
INA_0+
10
36
VDD
INA_0-
11
35
OUTA_0+
INA_1+
12
34
OUTA_0-
INA_1-
13
33
OUTA_1+
VDD
14
32
OUTA_1OUTA_2+
DAP = GND
23
24
25
26
27
VDD_SEL
SD_TH/READ_EN
ALL_DONE
OUTA_3-
VIN
28
RESERVED
18
21
INA_3-
22
OUTA_3+
RATE
INA_3+
29
RXDET
OUTA_2-
17
20
30
19
31
16
EQA1
15
INA_2-
EQA0
INA_2+
Figure 1. DS80PCI800 Pin Diagram 54 lead
Pin Functions
Pin Descriptions
Pin Name
Pin Number
I/O, Type
Pin Description
Differential High Speed I/O's
INB_0+, INB_0-,INB_1+,
INB_1-,INB_2+, INB_2,INB_3+, INB_3-,
1, 2, 3, 4,
5, 6, 7, 8,
I
Inverting and non-inverting differential inputs to bank B equalizer. A
gated on-chip 50Ω termination resistor connects INB_n+ to VDD and
INB_n- to VDD when enabled.
INA_0+, INA_0-,INA_1+,
INA_1-,INA_2+, INA_2,INA_3+, INA_3-
10, 11, 12, 13,
15, 16, 17, 18
I
Inverting and non-inverting differential inputs to bank B equalizer. A
gated on-chip 50Ω termination resistor connects INA_n+ to VDD and
INA_n- to VDD when enabled.
Submit Documentation Feedback
Copyright © 2011–2012, Texas Instruments Incorporated
Product Folder Links: DS80PCI800
3
DS80PCI800
SNLS334E – APRIL 2011 – REVISED MARCH 2012
www.ti.com
Pin Descriptions (continued)
Pin Name
Pin Number
I/O, Type
Pin Description
OUTB_0+,
OUTB_1+,
OUTB_2+,
OUTB_3+,
OUTB_0-,
OUTB_1-,
OUTB_2-,
OUTB_3-,
45, 44, 43, 42,
40, 39, 38, 37
O
Inverting and non-inverting 50Ω driver bank A outputs with de-emphasis.
Compatible with AC coupled CML inputs.
OUTA_0+,
OUTA_1+,
OUTA_2+,
OUTA_3+,
OUTA_0-,
OUTA_1-,
OUTA_2-,
OUTA_3-
35, 34, 33, 32,
31, 30, 29, 28
O
Inverting and non-inverting 50Ω driver bank A outputs with de-emphasis.
Compatible with AC coupled CML inputs.
I, FLOAT,
LVCMOS
System Management Bus (SMBus) enable pin
Tie 1kΩ to VDD = Register Access SMBus Slave Mode
FLOAT = Read External EEPROM (Master SMBUS Mode)
Tie 1kΩ to GND = Pin Mode
Control Pins — Shared (LVCMOS)
ENSMB
48
ENSMB = 1 (SMBUS MODE)
SCL
50
I, LVCMOS
O, OPEN Drain
ENSMB Master or Slave mode
SMBUS clock input is enabled (slave mode).
Clock output when loading EEPROM configuration (master mode).
SDA
49
I, LVCMOS,
O, OPEN Drain
ENSMB Master or Slave mode
The SMBus bi-directional SDA pin is enabled. Data input or open drain
(pull-down only) output.
AD0-AD3
54, 53, 47, 46
I, LVCMOS
ENSMB Master or Slave mode
SMBus Slave Address Inputs. In SMBus mode, these pins are the user
set SMBus slave address inputs.
READ_EN
26
I, LVCMOS
When using an External EEPROM, a transition from high to low starts
the load from the external EEPROM
EQA0, EQA1,
EQB0, EQB1
20, 19,
46, 47
I, 4-LEVEL,
LVCMOS
EQA[1:0] and EQB[1:0] control the level of equalization on the input pins.
The pins are active only when ENSMB is de-asserted (low). The 8
channels are organized into two banks. Bank A is controlled with the
EQA[1:0] pins and bank B is controlled with the EQB[1:0] pins. When
ENSMB goes high the SMBus registers provide independent control of
each channel. The EQB[1:0] pins are converted to SMBUS AD2/AD3
inputs. See Table 2.
DEMA0, DEMA1,
DEMB0, DEMB1
49, 50,
53, 54
I, 4-LEVEL,
LVCMOS
DEMA[1:0] and DEMB[1:0] control the level of de-emphasis of the output
driver when in Gen1/2 mode. The pins are only active when ENSMB is
de-asserted (low). The 8 channels are organized into two banks. Bank A
is controlled with the DEMA[1:0] pins and bank B is controlled with the
DEMB[1:0] pins. When ENSMB goes high the SMBus registers provide
independent control of each channel. The DEMA[1:0] pins are converted
to SMBUS SCL/SDA and DEMB[1:0] pins are converted to AD0, AD1
inputs.
See Table 3.
RATE
21
I, 4-LEVEL,
LVCMOS
RATE control pin selects GEN 1,2 and GEN 3 operating modes.
Tie 1kΩ to GND = GEN 1,2
FLOAT = AUTO Rate Select
Tie 20kΩ to GND = GEN 3 without De-emphasis
Tie 1kΩ to VDD = GEN 3 with De-emphasis
SD_TH
26
I, 4-LEVEL,
LVCMOS
Controls the internal Signal Detect Threshold.
See Table 5.
ENSMB = 0 (PIN MODE)
Control Pins — Both Pin and SMBus Modes (LVCMOS)
RXDET
22
I, 4-LEVEL,
LVCMOS
The RXDET pin controls the receiver detect function. Depending on the
input level, a 50Ω or >50kΩ termination to the power rail is enabled.
See Table 4.
RESERVED
23
I, FLOAT
Float (leave pin open) = Normal Operation
VDD_SEL
25
I, FLOAT
Controls the internal regulator
FLOAT = 2.5V mode
Tie GND = 3.3V mode
PRSNT
52
I, LVCMOS
Cable Present Detect input. high when a cable is not present per PCIe
Cabling Spec. 1.0. Puts part into low power mode. When LOW (normal
operation) part is enabled.
See Table 4.
4
Submit Documentation Feedback
Copyright © 2011–2012, Texas Instruments Incorporated
Product Folder Links: DS80PCI800
DS80PCI800
www.ti.com
SNLS334E – APRIL 2011 – REVISED MARCH 2012
Pin Descriptions (continued)
Pin Name
Pin Number
I/O, Type
Pin Description
27
O, LVCMOS
Valid Register Load Status Output
HIGH = External EEPROM load failed
LOW = External EEPROM load passed
VIN
24
Power
In 3.3V mode, feed 3.3V to VIN
In 2.5V mode, leave floating
VDD
9, 14, 36, 41, 51
Power
Power supply pins CML/analog
2.5V mode, connect to 2.5V supply
3.3V mode, connect 0.1uF cap to each VDD pin
GND
DAP
Power
Ground pad (DAP - die attach pad)
Outputs
ALL_DONE
Power
Notes:
LVCMOS inputs without the “FLOAT” conditions must be driven to a logic low or high at all times or operation is not guaranteed.
Input edge rate for LVCMOS/FLOAT inputs must be faster than 50 ns from 10–90%.
For 3.3V mode operation, VIN pin = 3.3V and the "VDD" for the 4-level input is 3.3V.
For 2.5V mode operation, VDD pin = 2.5V and the "VDD" for the 4-level input is 2.5V.
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
Absolute Maximum Ratings
(1)
Supply Voltage (VDD - 2.5V mode)
-0.5V to +2.75V
Supply Voltage (VIN - 3.3V mode)
-0.5V to +4.0V
LVCMOS Input/Output Voltage
-0.5V to +4.0V
CML Input Voltage
-0.5V to (VDD+0.5)
CML Input Current
-30 to +30 mA
Junction Temperature
125°C
Storage Temperature
-40°C to +125°C
Lead Temperature Range Soldering
(4 sec.)
+260°C
SQA54A Package
Derate SQA54A Package
52.6mW/°C above +25°C
ESD Rating
HBM, STD - JESD22-A114F
3 kV
MM, STD - JESD22-A115-A
200 V
CDM, STD - JESD22-C101-D
1000 V
Thermal Resistance
θJC
11.5°C/W
θJA, No Airflow, 4 layer JEDEC
19.1°C/W
For soldering specifications: see product folder at www.national.com/ms/MS/MS-SOLDERING.pdf
(1)
“Absolute Maximum Ratings” indicate limits beyond which damage to the device may occur, including inoperability and degradation of
device reliability and/or performance. Functional operation of the device and/or non-degradation at the Absolute Maximum Ratings or
other conditions beyond those indicated in the Recommended Operating Conditions is not implied. The Recommended Operating
Conditions indicate conditions at which the device is functional and the device should not be operated beyond such conditions. Absolute
Maximum Numbers are guaranteed for a junction temperature range of -40°C to +125°C. Models are validated to Maximum Operating
Voltages only.
Recommended Operating Conditions
Min
Typ
Max
Units
Supply Voltage (2.5V mode)
2.375
2.5
2.625
V
Supply Voltgae (3.3V mode)
3.0
3.3
3.6
V
Submit Documentation Feedback
Copyright © 2011–2012, Texas Instruments Incorporated
Product Folder Links: DS80PCI800
5
DS80PCI800
SNLS334E – APRIL 2011 – REVISED MARCH 2012
www.ti.com
Recommended Operating Conditions (continued)
Ambient Temperature
+85
°C
SMBus (SDA, SCL)
-40
3.6
V
Supply Noise up to 50 MHz
100
mVp-p
(1)
(1)
6
25
Allowed supply noise (mVp-p sine wave) under typical conditions.
Submit Documentation Feedback
Copyright © 2011–2012, Texas Instruments Incorporated
Product Folder Links: DS80PCI800
DS80PCI800
www.ti.com
SNLS334E – APRIL 2011 – REVISED MARCH 2012
Electrical Characteristics
Symbol
Parameter
Conditions
Power Dissipation
Min
Typ
Max
Units
VDD = 2.5 V supply,
EQ Enabled,
VOD = 1.0 Vp-p,
RXDET = 1, PRSNT = 0
500
700
mW
VIN = 3.3 V supply,
EQ Enabled,
VOD = 1.0 Vp-p,
RXDET = 1, PRSNT = 0
660
900
mW
Power
PD
LVCMOS / LVTTL DC Specifications
Vih
High Level Input
Voltage
2.0
3.6
V
Vil
Low Level Input
Voltage
0
0.8
V
Voh
High Level Output
Voltage
(ALL_DONE pin)
Ioh= −4mA
Vol
Low Level Output
Voltage
(ALL_DONE pin)
Iol= 4mA
Iih
Input High Current
(PRSNT pin)
VIN = 3.6 V,
LVCMOS = 3.6 V
Input High Current
with internal resistors
(4–level input pin)
Iil
Input Low Current
(PRSNT pin)
VIN = 3.6 V,
LVCMOS = 0 V
Input Low Current
with internal resistors
(4–level input pin)
2.0
V
0.4
V
-15
+15
uA
+20
+150
uA
-15
+15
uA
-160
-40
uA
CML Receiver Inputs (IN_n+, IN_n-)
RLrx-diff
0.05 - 1.25 GHz
-16
dB
1.25 - 2.5 GHz
-16
dB
2.5 - 4.0 GHz
-14
dB
RX Common mode
return loss
0.05 - 2.5 GHz
-12
dB
2.5 - 4.0 GHz
-8
dB
Zrx-dc
RX DC common mode
impedance
Tested at VDD = 2.5 V
40
50
60
Ω
Zrx-diff-dc
RX DC differntial mode
impedance
Tested at VDD = 2.5 V
80
100
120
Ω
Vrx-diff-dc
Differential RX peak to
peak voltage (VID)
Tested at pins
0.6
1.0
1.2
V
RLrx-cm
RX Differential return
loss
Zrx-high-imp-dc- DC Input common
pos
mode impedance for
V>0
VID = 0 to 200mV,
ENSMB = 0, RXDET = 0,
VDD = 2.5 V
50
KΩ
Vrx-signal-detdiff-pp
Signal detect assert
level for active data
signal
SD_TH = float,
0101 pattern at 8 Gbps
180
mVp-p
Vrx-idle-det-diffpp
Signal detect de-assert
level for electrical idle
SD_TH = float,
0101 pattern at 8 Gbps
110
mVp-p
High Speed Outputs
Submit Documentation Feedback
Copyright © 2011–2012, Texas Instruments Incorporated
Product Folder Links: DS80PCI800
7
DS80PCI800
SNLS334E – APRIL 2011 – REVISED MARCH 2012
www.ti.com
Electrical Characteristics (continued)
Vtx-diff-pp
Output Voltage
Differential Swing
Differential measurement with
OUT_n+ and OUT_n-,
terminated by 50Ω to GND,
AC-Coupled, VID = 1.0 Vp-p,
DEM0 = 1, DEM1 = 0,
0.8
1.0
1.2
Vp-p
(1)
Vtx-de-ratio_3.5
TX de-emphasis ratio
VOD = 1.0 Vp-p,
DEM0 = 0, DEM1 = R,
GEN 1, 2 modes only
-3.5
dB
Vtx-de-ratio_6
TX de-emphasis ratio
VOD = 1.0 Vp-p,
DEM0 = R, DEM1 = R,
GEN 1, 2 modes only
-6
dB
TTX-HF-DJ-DD
TX Dj > 1.5 MHz
0.15
UI
TTX-HF-DJ-DD
TX RMS jitter < 1.5
MHz
3.0
ps RMS
TTX-RISE-FALL
TX rise/fall time
20% to 80% of differential
output voltage
TRF-MISMATCH
TX rise/fall mismatch
20% to 80% of differential
output voltage
0.01
RLTX-DIFF
TX Differential return
loss
0.05 - 1.25 GHz
-16
dB
1.25 - 2.5 GHz
-12
dB
2.5 - 4 GHz
-11
dB
0.05 - 2.5 GHz
-12
dB
2.5 - 4 GHz
-8
dB
100
Ω
RLTX-CM
TX Common mode
return loss
35
45
ps
0.1
UI
ZTX-DIFF-DC
DC differential TX
impedance
VTX-CM-AC-PP
TX AC common mode
voltage
VOD = 1.0 Vp-p,
DEM0 = 1, DEM1 = 0
ITX-SHORT
TX short circuit current
limit
Total current the transmitter
can supply when shorted to
VDD or GND
VTX-CM-DC-
Absolute delta of DC
common mode voltage
during L0 and electrical
idle
100
mV
Absolute delta of DC
common mode voltgae
between TX+ and TX-
25
mV
ACTIVE-IDLE-DELTA
VTX-CM-DC-LINEDELTA
100
20
mVpp
mA
TTX-IDLE-DATA
Max time to transition
to differential DATA
signal after IDLE
VID = 1.0 Vp-p, 8 Gbps
3.5
ns
TTX-DATA-IDLE
Max time to transition
VID = 1.0 Vp-p, 8 Gbps
to IDLE after differential
DATA signal
6.2
ns
TPLHD/PHLD
High to Low
EQ = 00,
and Low to High
Differential Propagation
Delay
(2)
200
ps
TLSK
Lane to lane skew
T = 25C, VDD = 2.5V
25
ps
TPPSK
Part to part propagation T = 25C, VDD = 2.5V
delay skew
40
ps
Equalization
(1)
(2)
8
In GEN3 mode, the output VOD level is not fixed. It will be adjusted automatically based on the VID input amplitude level. The output
VOD level set by DEMA/B[1:0] in GEN3 mode is dependent on the VID level and the frequency content. The DS80PCI800 repeater in
GEN3 mode is designed to be transparent, so the TX-FIR (de-emphasis) is passed to the RX to support the PCIe GEN3 handshake
negotiation link training.
Propagation Delay measurements will change slightly based on the level of EQ selected. EQ = 00 will result in the shortest propagation
delays.
Submit Documentation Feedback
Copyright © 2011–2012, Texas Instruments Incorporated
Product Folder Links: DS80PCI800
DS80PCI800
www.ti.com
SNLS334E – APRIL 2011 – REVISED MARCH 2012
Electrical Characteristics (continued)
DJE1
Residual deterministic
jitter at 8 Gbps
35” 4mils FR4,
VID = 0.8 Vp-p,
PRBS15, EQ = 1F'h,
DEM = 0 dB
0.14
UI
DJE2
Residual deterministic
jitter at 5 Gbps
35” 4mils FR4,
VID = 0.8 Vp-p,
PRBS15,EQ = 1F'h,
DEM = 0 dB
0.1
UI
DJE3
Residual deterministic
jitter at 2.5 Gbps
35” 4mils FR4,
VID = 0.8 Vp-p,
PRBS15, EQ = 1F'h,
DEM = 0 dB
0.05
UI
DJE4
Residual deterministic
jitter at 8 Gbps
10 meters 30 awg cable,
VID = 0.8 Vp-p,
PRBS15, EQ = 2F'h,
DEM = 0 dB
0.16
UI
DJE5
Residual deterministic
jitter at 5 Gbps
10 meters 30 awg cable,
VID = 0.8 Vp-p,
PRBS15, EQ = 2F'h,
DEM = 0 dB
0.1
UI
DJE6
Residual deterministic
jitter at 2.5 Gbps
10 meters 30 awg cable,
VID = 0.8 Vp-p,
PRBS15, EQ = 2F'h,
DEM = 0 dB
0.05
UI
De-emphasis (GEN 1,2 mode only)
DJD1
Residual deterministic
jitter at 2.5 Gbps and
5.0 Gbps
10” 4mils FR4,
VID = 0.8 Vp-p,
PRBS15, EQ = 00,
VOD = 1.0 Vp-p,
DEM = −3.5 dB
0.1
UI
DJD2
Residual deterministic
jitter at 2.5 Gbps and
5.0 Gbps
20” 4mils FR4,
VID = 0.8 Vp-p,
PRBS15, EQ = 00,
VOD = 1.0 Vp-p,
DEM = −9 dB
0.1
UI
Submit Documentation Feedback
Copyright © 2011–2012, Texas Instruments Incorporated
Product Folder Links: DS80PCI800
9
DS80PCI800
SNLS334E – APRIL 2011 – REVISED MARCH 2012
www.ti.com
Electrical Characteristics — Serial Management Bus Interface
Over recommended operating supply and temperature ranges unless other specified.
Symbol
Parameter
Conditions
Min
Typ
Max
Units
0.8
V
3.6
V
SERIAL BUS INTERFACE DC SPECIFICATIONS
VIL
Data, Clock Input Low Voltage
VIH
Data, Clock Input High Voltage
IPULLUP
Current Through Pull-Up Resistor
or Current Source
VDD
Nominal Bus Voltage
ILEAK-Bus
Input Leakage Per Bus Segment
ILEAK-Pin
Input Leakage Per Device Pin
CI
Capacitance for SDA and SCL
(1) (2)
RTERM
External Termination Resistance
pull to VDD = 2.5V ± 5% OR 3.3V ±
10%
Pullup VDD = 3.3V,
2000
Ω
Pullup VDD = 2.5V,
1000
Ω
2.1
High Power Specification
(1)
4
mA
2.375
3.6
V
-200
+200
µA
-15
µA
10
(1) (2) (3)
(1) (2) (3)
pF
SERIAL BUS INTERFACE TIMING SPECIFICATIONS
FSMB
Bus Operating Frequency
ENSMB = VDD (Slave Mode)
ENSMB = FLOAT (Master Mode)
TBUF
Bus Free Time Between Stop and
Start Condition
THD:STA
Hold time after (Repeated) Start
Condition. After this period, the first
clock is generated.
280
400
400
kHz
520
kHz
1.3
µs
0.6
µs
At IPULLUP, Max
TSU:STA
Repeated Start Condition Setup
Time
0.6
µs
TSU:STO
Stop Condition Setup Time
0.6
µs
THD:DAT
Data Hold Time
0
ns
TSU:DAT
Data Setup Time
100
ns
TLOW
Clock Low Period
1.3
µs
THIGH
Clock High Period
(4)
50
µs
tF
Clock/Data Fall Time
(4)
300
ns
tR
Clock/Data Rise Time
(4)
300
ns
tPOR
Time in which a device must be
operational after power-on reset
500
ms
(1)
(2)
(3)
(4)
(5)
0.6
(4) (5)
Recommended value.
Recommended maximum capacitance load per bus segment is 400pF.
Maximum termination voltage should be identical to the device supply voltage.
Compliant to SMBus 2.0 physical layer specification. See System Management Bus (SMBus) Specification Version 2.0, section 3.1.1
SMBus common AC specifications for details.
Guaranteed by Design. Parameter not tested in production.
Timing Diagrams
(OUT+)
80%
VOD (p-p) = (OUT+) ± (OUT-)
80%
0V
20%
20%
(OUT-)
tRISE
tFALL
Figure 2. CML Output and Rise and FALL Transition Time
10
Submit Documentation Feedback
Copyright © 2011–2012, Texas Instruments Incorporated
Product Folder Links: DS80PCI800
DS80PCI800
www.ti.com
SNLS334E – APRIL 2011 – REVISED MARCH 2012
+
IN
0V
tPHLD
tPLHD
+
OUT
0V
-
Figure 3. Propagation Delay Timing Diagram
+
IN
0V
DATA
tDATA-IDLE
tIDLE-DATA
+
OUT
0V
DATA
IDLE
IDLE
Figure 4. Transmit IDLE-DATA and DATA-IDLE Response Time
tLOW
tR
tHIGH
SCL
tHD:STA
tBUF
tHD:DAT
tF
tSU:STA
tSU:DAT
tSU:STO
SDA
SP
ST
ST
SP
Figure 5. SMBus Timing Parameters
Functional Descriptions
The DS80PCI800 is a low power 8 channel repeater optimized for PCI Express Gen 1/2 and 3. The DS80PCI800
compensates for lossy FR-4 printed circuit board backplanes and balanced cables. The DS80PCI800 operates in
3 modes: Pin Control Mode (ENSMB = 0), SMBus Slave Mode (ENSMB = 1) and SMBus Master Mode (ENSMB
= float) to load register informations from external EEPROM; please refer to SMBUS Master Mode for additional
information.
Pin Control Mode:
Submit Documentation Feedback
Copyright © 2011–2012, Texas Instruments Incorporated
Product Folder Links: DS80PCI800
11
DS80PCI800
SNLS334E – APRIL 2011 – REVISED MARCH 2012
www.ti.com
When in pin mode (ENSMB = 0), equalization and de-emphasis can be selected via pin for each side
independently. When de-emphasis is asserted VOD is automatically adjusted per the De- Emphasis table below.
The RXDET pins provides automatic and manual control for input termination (50Ω or >50KΩ). RATE setting is
also pin controllable with pin selections (Gen 1/2, auto detect and Gen 3). The receiver electrical idle detect
threshold is also adjustable via the SD_TH pin.
SMBUS Mode:
When in SMBus mode (ENSMB = 1), the VOD (output amplitude), equalization, de-emphasis, and termination
disable features are all programmable on a individual lane basis, instead of grouped by A or B as in the pin mode
case. Upon assertion of ENSMB, the EQx and DEMx functions revert to register control immediately. The EQx
and DEMx pins are converted to AD0-AD3 SMBus address inputs. The other external control pins (RATE,
RXDET and SD_TH) remain active unless their respective registers are written to and the appropriate override bit
is set, in which case they are ignored until ENSMB is driven low (pin mode). On power-up and when ENSMB is
driven low all registers are reset to their default state. If PRSNT is asserted while ENSMB is high, the registers
retain their current state.
Equalization settings accessible via the pin controls were chosen to meet the needs of most PCIe applications. If
additional fine tuning or adjustment is needed, additional equalization settings can be accessed via the SMBus
registers. Each input has a total of 256 possible equalization settings. The tables show the 16 setting when the
device is in pin mode. When using SMBus mode, the equalization, VOD and de-Emphasis levels are set by
registers.
The input control pins have been enhanced to have 4 different levels and provide a wider range of control
settings when ENSMB=0.
Table 1. 4–Level Control Pin Settings
Pin Setting
Description (1)
Voltage at Pin
0
Tie 1kΩ to GND
0.03 x VDD
R
Tie 20kΩ to GND
1/3 x VDD
Float
Float (leave pin open)
2/3 x VDD
1
Tie 1kΩ to VDD
0.98 x VDD
(1)
The above required resistor value is for a single device. When there are multiple devices connected to the pull-up / pull-down resistor,
the value must scale with the number of devices. If 4 devices are connected to a single pull-up or pull-down, the 1kΩ resistor value
should be 250Ω. For the 20kΩ to GND, this should also scale to 5kΩ.
3.3V or 2.5V Supply Mode Operation
The DS80PCI800 has an optional internal voltage regulator to provide the 2.5V supply to the device. In 3.3V
mode operation, the VIN pin = 3.3V is used to supply power to the device. The internal regulator will provide the
2.5V to the VDD pins of the device and a 0.1 uF cap is needed at each of the 5 VDD pins for power supply decoupling (total capacitance should be ≤0.5 uF), and the VDD pins should be left open. The VDD_SEL pin must
be tied to GND to enable the internal regulator. In 2.5V mode operation, the VIN pin should be left open and 2.5V
supply must be applied to the 5 VDD pins to power the device. The VDD_SEL pin must be left open (no connect)
to disable the internal regulator.
12
Submit Documentation Feedback
Copyright © 2011–2012, Texas Instruments Incorporated
Product Folder Links: DS80PCI800
DS80PCI800
www.ti.com
SNLS334E – APRIL 2011 – REVISED MARCH 2012
3.3V mode
2.5V mode
VDD_SEL
Enable
VDD_SEL
open
VIN
open
Disable
3.3V
10 uF
1 uF
VIN
Internal
voltage
regulator
2.5V
VDD
VDD
0.1 uF
0.1 uF
VDD
VDD
0.1 uF
0.1 uF
1 uF
2.5V
Capacitors can be
either tantalum or an
ultra-low ESR seramic.
10 uF
Internal
voltage
regulator
Capacitors can be
either tantalum or an
ultra-low ESR seramic.
VDD
VDD
0.1 uF
0.1 uF
VDD
VDD
0.1 uF
0.1 uF
VDD
VDD
0.1 uF
0.1 uF
Place 0.1 uF close to VDD Pin
Total capacitance should be 7 0.5 uF
Place capcitors close to VDD Pin
Figure 6. 3.3V or 2.5V Supply Connection Diagram
System Information
When using the DS80PCI800 in CPU systems, there are specific signal integrity settings to ensure signal
integrity margin. The settings were achieved with completing extensive testing. Please contact your field
representative for more information regarding the testing completed to achieve these settings.
For tuning the in the downstream direction (from CPU to EP).
• EQ: use the guidelines outlined in table 2.
• De-Emphasis: use the guidelines outlined in table 3.
• VOD: use the guidelines outlined in table 3.
For tuning in the upstream direction (from EP to CPU).
• EQ: use the guidelines outlined in table 2.
• De-Emphasis:
– For trace lengths < 15” set to -3.5 dB
– For trace lengths > 15” set to -6 dB
• VOD: set to 900 mV
Table 2. Equalizer Settings
Level
EQA1
EQB1
EQA0
EQB0
EQ – 8 bits [7:0]
dB at
1.25 GHz
dB at
2.5 GHz
dB at
4 GHz
Suggested Use
1
0
0
0000 0000 = 0x00
2.1
3.7
4.9
FR4 < 5 inch trace
Submit Documentation Feedback
Copyright © 2011–2012, Texas Instruments Incorporated
Product Folder Links: DS80PCI800
13
DS80PCI800
SNLS334E – APRIL 2011 – REVISED MARCH 2012
www.ti.com
Table 2. Equalizer Settings (continued)
2
0
R
0000 0001 = 0x01
3.4
5.8
7.9
FR4 5 inch 5–mil trace
3
0
Float
0000 0010 = 0x02
4.8
7.7
9.9
FR4 5 inch 4–mil trace
4
0
1
0000 0011 = 0x03
5.9
8.9
11.0
FR4 10 inch 5–mil trace
5
R
0
0000 0111 = 0x07
7.2
11.2
14.3
FR4 10 inch 4–mil trace
6
R
R
0001 0101 = 0x15
6.1
11.4
14.6
FR4 15 inch 4–mil trace
7
R
Float
0000 1011 = 0x0B
8.8
13.5
17.0
FR4 20 inch 4–mil trace
8
R
1
0000 1111 = 0x0F
10.2
15.0
18.5
FR4 25 to 30 inch 4–mil trace
9
Float
0
0101 0101 = 0x55
7.5
12.8
18.0
FR4 30 inch 4–mil trace
10
Float
R
0001 1111 = 0x1F
11.4
17.4
22.0
FR4 35 inch 4–mil trace
11
Float
Float
0010 1111 = 0x2F
13.0
19.7
24.4
10m, 30awg cable
12
Float
1
0011 1111 = 0x3F
14.2
21.1
25.8
10m – 12m cable
13
1
0
1010 1010 = 0xAA
13.8
21.7
27.4
14
1
R
0111 1111 = 0x7F
15.6
23.5
29.0
15
1
Float
1011 1111 = 0xBF
17.2
25.8
31.4
16
1
1
1111 1111 = 0xFF
18.4
27.3
32.7
Table 3. Output Voltage and De-emphasis Settings
Level
DEMA1
DEMB1
DEMA0
DEMB0
VOD Vp-p
DEM dB
(see note below)
Inner Amplitude
Vp-p
Suggested Use
1
0
0
0.8
0
0.8
FR4 <5 inch 4–mil trace
2
0
R
0.9
0
0.9
FR4 <5 inch 4–mil trace
3
0
Float
0.9
- 3.5
0.6
FR4 10 inch 4–mil trace
4
0
1
1.0
0
1.0
FR4 <5 inch 4–mil trace
5
R
0
1.0
- 3.5
0.7
FR4 10 inch 4–mil trace
6
R
R
1.0
-6
0.5
FR4 15 inch 4–mil trace
7
R
Float
1.1
0
1.1
FR4 <5 inch 4–mil trace
8
R
1
1.1
- 3.5
0.7
FR4 10 inch 4–mil trace
9
Float
0
1.1
-6
0.6
FR4 15 inch 4–mil trace
10
Float
R
1.2
0
1.2
FR4 <5 inch 4–mil trace
11
Float
Float
1.2
- 3.5
0.8
FR4 10 inch 4–mil trace
12
Float
1
1.2
-6
0.6
FR4 15 inch 4–mil trace
13
1
0
1.3
0
1.3
FR4 <5 inch 4–mil trace
14
1
R
1.3
- 3.5
0.9
FR4 10 inch 4–mil trace
15
1
Float
1.3
-6
0.7
FR4 15 inch 4–mil trace
16
1
1
1.3
-9
0.5
FR4 20 inch 4–mil trace
Note: The VOD output amplitude and DEM de-emphasis levels are set with the DEMA/B[1:0] pins.
The de-emphasis levels are also available in GEN 3 mode when RATE = 1 (tied to VDD).
Table 4. RX-Detect Settings
14
PRSNT#
RXDET
SMBus REG
bit[3:2]
Input Termination
Termination sensed
on output pins
0
0
00
High Impedance
X
0
Tie 20kΩ
to GND
01
High Impedance
50 Ω
High Z until receiver
is detected
Submit Documentation Feedback
Comments
Manual RX-Detect, input is high impedance
mode
Auto RX-Detect, outputs test every 12 msec
for 600 msec then stops; termination is high-z
until detection; once detected input termination
is 50 Ω
Reset function by pulsing PRSNT# high for 5
usec then low again
Copyright © 2011–2012, Texas Instruments Incorporated
Product Folder Links: DS80PCI800
DS80PCI800
www.ti.com
SNLS334E – APRIL 2011 – REVISED MARCH 2012
Table 4. RX-Detect Settings (continued)
0
Float
(Default)
10
High Impedance
50 Ω
High Z until recevier
is detected
Auto RX-Detect, outputs test every 12 msec
until detection occurs; termination is high-z
until detection; once detected input termination
is 50 Ω
0
1
11
50 Ω
X
Manual RX-Detect, input is 50 Ω
1
X
High Impedance
X
Power down mode, input is high impedance,
output drivers are disabled
Used to reset RX-Detect State Machine when
held high for 5 usec
Table 5. Signal Detect Threshold Level (1)
SD_TH
SMBus REG bit [3:2] and [1:0]
Assert Level (typ)
De-assert Level (typ)
0
10
210 mVp-p
150 mVp-p
R
01
160 mVp-p
100 mVp-p
F (default)
00
180 mVp-p
110 mVp-p
1
11
190 mVp-p
130 mVp-p
(1)
VDD = 2.5V, 25°C and 0101 pattern at 8 Gbps
SMBUS Master Mode
The DS80PCI800 devices support reading directly from an external EEPROM device by implementing SMBus
Master mode. When using the SMBus master mode, the DS80PCI800 will read directly from specific location in
the external EEPROM. When designing a system for using the external EEPROM, the user needs to follow these
specific guidelines.
• Set ENSMB = Float — enable the SMBUS master mode.
• The external EEPROM device address byte must be 0xA0'h and capable of 400 kHz operation at 2.5V and
3.3V supply.
• Set the AD[3:0] inputs for SMBus address byte. When the AD[3:0] = 0000'b, the device address byte is B0'h.
When tying multiple DS80PCI800 devices to the SDA and SCL bus, use these guidelines to configure the
devices.
• Use SMBus AD[3:0] address bits so that each device can loaded it's configuration from the EEPROM.
Example below is for 4 device.
– U1: AD[3:0] = 0000 = 0xB0'h,
– U2: AD[3:0] = 0001 = 0xB2'h,
– U3: AD[3:0] = 0010 = 0xB4'h,
– U4: AD[3:0] = 0011 = 0xB6'h
• Use a pull-up resistor on SDA and SCL; value = 2k ohms
• Daisy-chain READEN# (pin 26) and ALL_DONE# (pin 27) from one device to the next device in the sequence
so that they do not compete for the EEPROM at the same time.
– 1. Tie READEN# of the 1st device in the chain (U1) to GND
– 2. Tie ALL_DONE# of U1 to READEN# of U2
– 3. Tie ALL_DONE# of U2 to READEN# of U3
– 4. Tie ALL_DONE# of U3 to READEN# of U4
– 5. Optional: Tie ALL_DONE# output of U4 to a LED to show the devices have been loaded successfully
Below is an example of a 2 kbits (256 x 8-bit) EEPROM in hex format for the DS80PCI800 device. The first 3
bytes of the EEPROM always contain a header common and necessary to control initialization of all devices
connected to the I2C bus. CRC enable flag to enable/disable CRC checking. If CRC checking is disabled, a fixed
pattern (8’hA5) is written/read instead of the CRC byte from the CRC location, to simplify the control. There is a
MAP bit to flag the presence of an address map that specifies the configuration data start in the EEPROM. If the
MAP bit is not present the configuration data start address is derived from the DS80PCI800 address and the
configuration data size. A bit to indicate an EEPROM size > 256 bytes is necessary to properly address the
EEPROM. There are 37 bytes of data size for each DS80PCI800 device.
Submit Documentation Feedback
Copyright © 2011–2012, Texas Instruments Incorporated
Product Folder Links: DS80PCI800
15
DS80PCI800
SNLS334E – APRIL 2011 – REVISED MARCH 2012
www.ti.com
:2000000000001000000407002FAD4002FAD4002FAD4002FAD401805F5A8005F5A8005F5AD8
:200020008005F5A800005454000000000000000000000000000000000000000000000000F6
:20006000000000000000000000000000000000000000000000000000000000000000000080
:20008000000000000000000000000000000000000000000000000000000000000000000060
:2000A000000000000000000000000000000000000000000000000000000000000000000040
:2000C000000000000000000000000000000000000000000000000000000000000000000020
:2000E000000000000000000000000000000000000000000000000000000000000000000000
:200040000000000000000000000000000000000000000000000000000000000000000000A0
16
Submit Documentation Feedback
Copyright © 2011–2012, Texas Instruments Incorporated
Product Folder Links: DS80PCI800
DS80PCI800
www.ti.com
SNLS334E – APRIL 2011 – REVISED MARCH 2012
Table 6. EEPROM Register Map - Single Device with Default Value
EEPROM Address
Byte
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
BIt 0
Description
CRC EN
Address Map
Present
EEPROM > 256
Bytes
RES
DEVICE
COUNT[3]
DEVICE
COUNT[2]
DEVICE
COUNT[1]
DEVICE
COUNT[0]
0
0
0
0
0
0
0
0
RES
RES
RES
RES
RES
RES
RES
RES
0
0
0
0
0
0
0
0
Max EEPROM
Burst size[7]
Max EEPROM
Burst size[6]
Max EEPROM
Burst size[5]
Max EEPROM
Burst size[4]
Max EEPROM
Burst size[3]
Max EEPROM
Burst size[2]
Max EEPROM
Burst size[1]
Max EEPROM
Burst size[0]
0
0
0
0
0
0
0
0
PWDN_ch7
PWDN_ch6
PWDN_ch5
PWDN_ch4
PWDN_ch3
PWDN_ch2
PWDN_ch1
PWDN_ch0
0
0
0
0
0
0
0
0
lpbk_1
lpbk_0
PWDN_INPUTS
PWDN_OSC
Ovrd_PRSNT
RES
RES
RES
0
0
0
0
0
0
0
0
RES
RES
RES
RES
RES
rxdet_btb_en
Ovrd_idle_th
Ovrd_RES
0
0
0
0
0
1
0
0
Ovrd_IDLE
Ovrd_RX_DET
Ovrd_RATE
RES
RES
rx_delay_sel_2
rx_delay_sel_1
rx_delay_sel_0
0
0
0
0
0
1
1
1
RD_delay_sel_3
RD_delay_sel_2
RD_delay_sel_1
RD_delay_sel_0
ch0_Idle_auto
ch0_Idle_sel
ch0_RXDET_1
ch0_RXDET_0
0
0
0
0
0
0
0
0
ch0_BST_7
ch0_BST_6
ch0_BST_5
ch0_BST_4
ch0_BST_3
ch0_BST_2
ch0_BST_1
ch0_BST_0
0
0
1
0
1
1
1
1
ch0_Sel_scp
ch0_Sel_mode
ch0_RES_2
ch0_RES_1
ch0_RES_0
ch0_VOD_2
ch0_VOD_1
ch0_VOD_0
1
0
1
0
1
1
0
1
ch0_DEM_2
ch0_DEM_1
ch0_DEM_0
ch0_Slow
ch0_idle_tha_1
ch0_idle_tha_0
ch0_idle_thd_1
ch0_idle_thd_0
0
1
0
0
0
0
0
0
ch1_Idle_auto
ch1_Idle_sel
ch1_RXDET_1
ch1_RXDET_0
ch1_BST_7
ch1_BST_6
ch1_BST_5
ch1_BST_4
0
0
0
0
0
0
1
0
ch1_BST_3
ch1_BST_2
ch1_BST_1
ch1_BST_0
ch1_Sel_scp
ch1_Sel_mode
ch1_RES_2
ch1_RES_1
1
1
1
1
1
0
1
0
ch1_RES_0
ch1_VOD_2
ch1_VOD_1
ch1_VOD_0
ch1_DEM_2
ch1_DEM_1
ch1_DEM_0
ch1_Slow
1
1
0
1
0
1
0
0
ch1_idle_tha_1
ch1_idle_tha_0
ch1_idle_thd_1
ch1_idle_thd_0
ch2_Idle_auto
ch2_Idle_sel
ch2_RXDET_1
ch2_RXDET_0
0
0
0
0
0
0
0
0
ch2_BST_7
ch2_BST_6
ch2_BST_5
ch2_BST_4
ch2_BST_3
ch2_BST_2
ch2_BST_1
ch2_BST_0
0
0
1
0
1
1
1
1
0
Value
Description
1
Value
Description
2
Value
Description
3
Value
Description
4
Value
Description
5
Value
Description
6
Value
Description
7
Value
Description
8
Value
Description
9
Value
Description
10
Value
Description
11
Value
Description
12
Value
Description
13
Value
Description
14
Value
Description
Value
15
Submit Documentation Feedback
Copyright © 2011–2012, Texas Instruments Incorporated
Product Folder Links: DS80PCI800
17
DS80PCI800
SNLS334E – APRIL 2011 – REVISED MARCH 2012
www.ti.com
Table 6. EEPROM Register Map - Single Device with Default Value (continued)
EEPROM Address
Byte
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
BIt 0
Description
ch2_Sel_scp
ch2_Sel_mode
ch2_RES_2
ch2_RES_1
ch2_RES_0
ch2_VOD_2
ch2_VOD_1
ch2_VOD_0
1
0
1
0
1
1
0
1
ch2_DEM_2
ch2_DEM_1
ch2_DEM_0
ch2_Slow
ch2_idle_tha_1
ch2_idle_tha_0
ch2_idle_thd_1
ch2_idle_thd_0
0
1
0
0
0
0
0
0
ch3_Idle_auto
ch3_Idle_sel
ch3_RXDET_1
ch3_RXDET_0
ch3_BST_7
ch3_BST_6
ch3_BST_5
ch3_BST_4
0
0
0
0
0
0
1
0
ch3_BST_3
ch3_BST_2
ch3_BST_1
ch3_BST_0
ch3_Sel_scp
ch3_Sel_mode
ch3_RES_2
ch3_RES_1
1
1
1
1
1
0
1
0
ch3_RES_0
ch3_VOD_2
ch3_VOD_1
ch3_VOD_0
ch3_DEM_2
ch3_DEM_1
ch3_DEM_0
ch3_Slow
1
1
0
1
0
1
0
0
ch3_idle_tha_1
ch3_idle_tha_0
ch3_idle_thd_1
ch3_idle_thd_0
ovrd_fast_idle
en_high_idle_th_n
en_high_idle_th_s
en_fast_idle_n
0
0
0
0
0
0
0
1
en_fast_idle_s
eqsd_mgain_n
eqsd_mgain_s
ch4_Idle_auto
ch4_Idle_sel
ch4_RXDET_1
ch4_RXDET_0
ch4_BST_7
1
0
0
0
0
0
0
0
ch4_BST_6
ch4_BST_5
ch4_BST_4
ch4_BST_3
ch4_BST_2
ch4_BST_1
ch4_BST_0
ch4_Sel_scp
0
1
0
1
1
1
1
1
ch4_Sel_mode
ch4_RES_2
ch4_RES_1
ch4_RES_0
ch4_VOD_2
ch4_VOD_1
ch4_VOD_0
ch4_DEM_2
0
1
0
1
1
0
1
0
ch4_DEM_1
ch4_DEM_0
ch4_Slow
ch4_idle_tha_1
ch4_idle_tha_0
ch4_idle_thd_1
ch4_idle_thd_0
ch5_Idle_auto
1
0
0
0
0
0
0
0
ch5_Idle_sel
ch5_RXDET_1
ch5_RXDET_0
ch5_BST_7
ch5_BST_6
ch5_BST_5
ch5_BST_4
ch5_BST_3
0
0
0
0
0
1
0
1
ch5_BST_2
ch5_BST_1
ch5_BST_0
ch5_Sel_scp
ch5_Sel_mode
ch5_RES_2
ch5_RES_1
ch5_RES_0
1
1
1
1
0
1
0
1
ch5_VOD_2
ch5_VOD_1
ch5_VOD_0
ch5_DEM_2
ch5_DEM_1
ch5_DEM_0
ch5_Slow
ch5_idle_tha_1
1
0
1
0
1
0
0
0
ch5_idle_tha_0
ch5_idle_thd_1
ch5_idle_thd_0
ch6_Idle_auto
ch6_Idle_sel
ch6_RXDET_1
ch6_RXDET_0
ch6_BST_7
0
0
0
0
0
0
0
0
ch6_BST_6
ch6_BST_5
ch6_BST_4
ch6_BST_3
ch6_BST_2
ch6_BST_1
ch6_BST_0
ch6_Sel_scp
0
1
0
1
1
1
1
1
ch6_Sel_mode
ch6_RES_2
ch6_RES_1
ch6_RES_0
ch6_VOD_2
ch6_VOD_1
ch6_VOD_0
ch6_DEM_2
0
1
0
1
1
0
1
0
16
Value
Description
17
Value
Description
18
Value
Description
19
Value
Description
20
Value
Description
21
Value
Description
22
Value
Description
23
Value
Description
24
Value
Description
25
Value
Description
26
Value
Description
27
Value
Description
28
Value
Description
29
Value
Description
30
Value
Description
Value
18
31
Submit Documentation Feedback
Copyright © 2011–2012, Texas Instruments Incorporated
Product Folder Links: DS80PCI800
DS80PCI800
www.ti.com
SNLS334E – APRIL 2011 – REVISED MARCH 2012
Table 6. EEPROM Register Map - Single Device with Default Value (continued)
EEPROM Address
Byte
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
BIt 0
Description
ch6_DEM_1
ch6_DEM_0
ch6_Slow
ch6_idle_tha_1
ch6_idle_tha_0
ch6_idle_thd_1
ch6_idle_thd_0
ch7_Idle_auto
1
0
0
0
0
0
0
0
ch7_Idle_sel
ch7_RXDET_1
ch7_RXDET_0
ch7_BST_7
ch7_BST_6
ch7_BST_5
ch7_BST_4
ch7_BST_3
0
0
0
0
0
1
0
1
ch7_BST_2
ch7_BST_1
ch7_BST_0
ch7_Sel_scp
ch7_Sel_mode
ch7_RES_2
ch7_RES_1
ch7_RES_0
1
1
1
1
0
1
0
1
ch7_VOD_2
ch7_VOD_1
ch7_VOD_0
ch7_DEM_2
ch7_DEM_1
ch7_DEM_0
ch7_Slow
ch7_idle_tha_1
1
0
1
0
1
0
0
0
ch7_idle_tha_0
ch7_idle_thd_1
ch7_idle_thd_0
iph_dac_ns_1
iph_dac_ns_0
ipp_dac_ns_1
ipp_dac_ns_0
ipp_dac_1
0
0
0
0
0
0
0
0
ipp_dac_0
RD23_67
RD01_45
RD_PD_ovrd
RD_Sel_test
RD_RESET_ovrd
PWDB_input_DC
DEM_VOD_ovrd
0
0
0
0
0
0
0
0
DEM_ovrd_N2
DEM_ovrd_N1
DEM_ovrd_N0
VOD_ovrd_N2
VOD_ovrd_N1
VOD_ovrd_N0
SPARE0
SPARE1
0
1
0
1
0
1
0
0
DEM__ovrd_S2
DEM__ovrd_S1
DEM_ovrd_S0
VOD_ovrd_S2
VOD_ovrd_S1
VOD_ovrd_S0
SPARE0
SPARE1
0
1
0
1
0
1
0
0
32
Value
Description
33
Value
Description
34
Value
Description
35
Value
Description
36
Value
Description
37
Value
Description
38
Value
Description
Value
39
Submit Documentation Feedback
Copyright © 2011–2012, Texas Instruments Incorporated
Product Folder Links: DS80PCI800
19
DS80PCI800
SNLS334E – APRIL 2011 – REVISED MARCH 2012
www.ti.com
Table 7. Example of EEPROM for 4 Devices using 2 Address Maps
EEPROM Address
Address (Hex)
EEPROM Data
Comments
0
00
0x43
CRC_EN = 0, Address Map = 1, >256 bytes = 0, Device
Count[3:0] = 3
1
01
0x00
2
02
0x08
EEPROM Burst Size
3
03
0x00
CRC not used
4
04
0x0B
Device 0 Address Location
5
05
0x00
CRC not used
6
06
0x0B
Device 1 Address Location
7
07
0x00
CRC not used
8
08
0x30
Device 2 Address Location
9
09
0x00
CRC not used
10
0A
0x30
Device 3 Address Location
11
0B
0x00
Begin Device 0, 1 - Address Offset 3
12
0C
0x00
13
0D
0x04
14
0E
0x07
15
0F
0x00
16
10
0x00
EQ CHB0 = 00
17
11
0xAB
VOD CHB0 = 1.0V
18
12
0x00
DEM CHB0 = 0 (0dB)
19
13
0x00
EQ CHB1 = 00
20
14
0x0A
VOD CHB1 = 1.0V
21
15
0xB0
DEM CHB1 = 0 (0dB)
22
16
0x00
23
17
0x00
EQ CHB2 = 00
24
18
0xAB
VOD CHB2 = 1.0V
25
19
0x00
DEM CHB2 = 0 (0dB)
26
1A
0x00
EQ CHB3 = 00
27
1B
0x0A
VOD CHB3 = 1.0V
28
1C
0xB0
DEM CHB3 = 0 (0dB)
29
1D
0x01
30
1E
0x80
31
1F
0x01
EQ CHA0 = 00
32
20
0x56
VOD CHA0 = 1.0V
33
21
0x00
DEM CHA0 = 0 (0dB)
34
22
0x00
EQ CHA1 = 00
35
23
0x15
VOD CHA1 = 1.0V
36
24
0x60
DEM CHA1 = 0 (0dB)
37
25
0x00
38
26
0x01
EQ CHA2 = 00
39
27
0x56
VOD CHA2 = 1.0V
40
28
0x00
DEM CHA2 = 0 (0dB)
41
29
0x00
EQ CHA3 = 00
42
2A
0x15
VOD CHA3 = 1.0V
43
2B
0x60
DEM CHA3 = 0 (0dB)
44
2C
0x00
45
2D
0x00
46
2E
0x54
20
Submit Documentation Feedback
Copyright © 2011–2012, Texas Instruments Incorporated
Product Folder Links: DS80PCI800
DS80PCI800
www.ti.com
SNLS334E – APRIL 2011 – REVISED MARCH 2012
Table 7. Example of EEPROM for 4 Devices using 2 Address Maps (continued)
47
2F
0x54
End Device 0, 1 - Address Offset 39
48
30
0x00
Begin Device 2, 3 - Address Offset 3
49
31
0x00
50
32
0x04
51
33
0x07
52
34
0x00
53
35
0x00
EQ CHB0 = 00
54
36
0xAB
VOD CHB0 = 1.0V
55
37
0x00
DEM CHB0 = 0 (0dB)
56
38
0x00
EQ CHB1 = 00
57
39
0x0A
VOD CHB1 = 1.0V
58
3A
0xB0
DEM CHB1 = 0 (0dB)
59
3B
0x00
60
3C
0x00
EQ CHB2 = 00
61
3D
0xAB
VOD CHB2 = 1.0V
62
3E
0x00
DEM CHB2 = 0 (0dB)
63
3F
0x00
EQ CHB3 = 00
64
40
0x0A
VOD CHB3 = 1.0V
65
41
0xB0
DEM CHB3 = 0 (0dB)
66
42
0x01
67
43
0x80
68
44
0x01
EQ CHA0 = 00
69
45
0x56
VOD CHA0 = 1.0V
70
46
0x00
DEM CHA0 = 0 (0dB)
71
47
0x00
EQ CHA1 = 00
72
48
0x15
VOD CHA1 = 1.0V
73
49
0x60
DEM CHA1 = 0 (0dB)
74
4A
0x00
75
4B
0x01
EQ CHA2 = 00
76
4C
0x56
VOD CHA2 = 1.0V
77
4D
0x00
DEM CHA2 = 0 (0dB)
78
4E
0x00
EQ CHA3 = 00
79
4F
0x15
VOD CHA3 = 1.0V
80
50
0x60
DEM CHA3 = 0 (0dB)
81
51
0x00
82
52
0x00
83
53
0x54
84
54
0x54
End Device 2, 3 - Address Offset 39
Note: CRC_EN = 0, Address Map = 1, >256 byte = 0, Device Count[3:0] = 3. This example has all 8–channels
set to EQ = 00 (min boost), VOD = 1.0V, DEM = 0 (0dB) and multiple device can point to the same address map.
System Management Bus (SMBus) and Configuration Registers
The System Management Bus interface is compatible to SMBus 2.0 physical layer specification. ENSMB = 1kΩ
to VDD to enable SMBus slave mode and allow access to the configuration registers.
The DS80PCI800 has the AD[3:0] inputs in SMBus mode. These pins are the user set SMBUS slave address
inputs. The AD[3:0] pins have internal pull-down. When left floating or pulled low the AD[3:0] = 0000'b, the device
default address byte is B0'h. Based on the SMBus 2.0 specification, the DS80PCI800 has a 7-bit slave address.
The LSB is set to 0'b (for a WRITE). The device supports up to 16 address byte, which can be set with the
AD[3:0] inputs. Below are the 16 addresses.
Submit Documentation Feedback
Copyright © 2011–2012, Texas Instruments Incorporated
Product Folder Links: DS80PCI800
21
DS80PCI800
SNLS334E – APRIL 2011 – REVISED MARCH 2012
www.ti.com
Table 8. Device Slave Address Bytes
AD[3:0] Settings
Address Bytes (HEX)
0000
B0
0001
B2
0010
B4
0011
B6
0100
B8
0101
BA
0110
BC
0111
BE
1000
C0
1001
C2
1010
C4
1011
C6
1100
C8
1101
CA
1110
CC
1111
CE
The SDA, SCL pins are 3.3V tolerant, but are not 5V tolerant. External pull-up resistor is required on the SDA.
The resistor value can be from 1 kΩ to 5 kΩ depending on the voltage, loading and speed. The SCL may also
require an external pull-up resistor and it depends on the Host that drives the bus.
TRANSFER OF DATA VIA THE SMBus
During normal operation the data on SDA must be stable during the time when SCL is High.
There are three unique states for the SMBus:
START: A High-to-Low transition on SDA while SCL is High indicates a message START condition.
STOP: A Low-to-High transition on SDA while SCL is High indicates a message STOP condition.
IDLE: If SCL and SDA are both High for a time exceeding tBUF from the last detected STOP condition or if they
are High for a total exceeding the maximum specification for tHIGH then the bus will transfer to the IDLE state.
SMBus TRANSACTIONS
The device supports WRITE and READ transactions. See Register Description table for register address, type
(Read/Write, Read Only), default value and function information.
WRITING A REGISTER
To
1.
2.
3.
4.
5.
6.
7.
write a register, the following protocol is used (see SMBus 2.0 specification).
The Host drives a START condition, the 7-bit SMBus address, and a “0” indicating a WRITE.
The Device (Slave) drives the ACK bit (“0”).
The Host drives the 8-bit Register Address.
The Device drives an ACK bit (“0”).
The Host drive the 8-bit data byte.
The Device drives an ACK bit (“0”).
The Host drives a STOP condition.
The WRITE transaction is completed, the bus goes IDLE and communication with other SMBus devices may
now occur.
READING A REGISTER
To read a register, the following protocol is used (see SMBus 2.0 specification).
22
Submit Documentation Feedback
Copyright © 2011–2012, Texas Instruments Incorporated
Product Folder Links: DS80PCI800
DS80PCI800
www.ti.com
SNLS334E – APRIL 2011 – REVISED MARCH 2012
1. The Host drives a START condition, the 7-bit SMBus address, and a “0” indicating a WRITE.
2. The Device (Slave) drives the ACK bit (“0”).
3. The Host drives the 8-bit Register Address.
4. The Device drives an ACK bit (“0”).
5. The Host drives a START condition.
6. The Host drives the 7-bit SMBus Address, and a “1” indicating a READ.
7. The Device drives an ACK bit “0”.
8. The Device drives the 8-bit data value (register contents).
9. The Host drives a NACK bit “1”indicating end of the READ transfer.
10. The Host drives a STOP condition.
The READ transaction is completed, the bus goes IDLE and communication with other SMBus devices may now
occur.
Please see SMBus Register Map Table for more information.
Table 9. SMBUS Slave Mode Register Map
Address
Register Name
Bit (s) Field
Type
Default
Description
0x00
Observation,
Reset
7
Reserved
R/W
0x00
Set bit to 0.
6:3
Address Bit
AD[3:0]
R
Observation of AD[3:0] bit
[6]: AD3
[5]: AD2
[4]: AD1
[3]: AD0
2
EEPROM Read
Done
R
1: Device completed the read from external
EEPROM.
1
Block Reset
R/W
1: Block bit 0 from resettting the registers; self
clearing.
0
Reset
R/W
SMBus Reset
1: Reset registers to default value; self clearing.
0x01
PWDN Channels
7:0
PWDN CHx
R/W
0x00
Power Down per Channel
[7]: CH7 – CHA_3
[6]: CH6 – CHA_2
[5]: CH5 – CHA_1
[4]: CH4 – CHA_0
[3]: CH3 – CHB_3
[2]: CH2 – CHB_2
[1]: CH1 – CHB_1
[0]: CH0 – CHB_0
00'h = all channels enabled
FF'h = all channels disabled
Note: override PRSNT pin.
0x02
Override
PRSNT Control
7:1
Reserved
R/W
0x00
Set bits to 0.
0
Override PRSNT
1: Block PRSNT pin control
0: Allow PRSNT pin control
0x05
Slave Mode CRC Bits 7:0
CRC bits
R/W
0x00
CRC bits [7:0]
0x06
Slave CRC Control
7:5
Reserved
R/W
0x10
Set bits to 0.
4
Reserved
Set bit to 1.
3
Slave CRC
1: Disables the slave CRC mode
0: Enables the slave CRC mode
Note: In order to change VOD, DEM and EQ of the
channels in slave mode, set bit to 1 to disable the
CRC.
2:0
Reserved
Set bits to 0.
Submit Documentation Feedback
Copyright © 2011–2012, Texas Instruments Incorporated
Product Folder Links: DS80PCI800
23
DS80PCI800
SNLS334E – APRIL 2011 – REVISED MARCH 2012
www.ti.com
Table 9. SMBUS Slave Mode Register Map (continued)
Address
Register Name
Bit (s) Field
Type
Default
Description
0x08
Override
Pin Control
7
Reserved
R/W
0x00
Set bit to 0.
6
Override SD_TH
1: Block SD_TH pin control
0: Allow SD_TH pin control
5
Reserved
Set bit to 0.
4
Override IDLE
1: IDLE control by registers
0: IDLE control by signal detect
3
Override RXDET
1: Block RXDET pin control
0: Allow RXDET pin control
2
Override RATE
1: Block RATE pin control
0: Allow RATE pin control
1
Reserved
Set bit to 0.
0
Reserved
7:6
Reserved
5
IDLE_AUTO
1: Automatic IDLE detect
0: Allow IDLE_SEL control in bit 4
Note: override IDLE control.
4
IDLE_SEL
1: Output is MUTED (electrical idle)
0: Output is ON
Note: override IDLE control.
3:2
RXDET
00: Input is high-z impedance
01: Auto RX-Detect,
outputs test every 12 ms for 600 ms (50 times) then
stops; termination is high-z until detection; once
detected input termination is 50 Ω
10: Auto RX-Detect,
outputs test every 12 ms until detection occurs;
termination is high-z until detection; once detected
input termination is 50 Ω
11: Input is 50 Ω
Note: override RXDET pin.
0x0E
CH0 - CHB0
IDLE, RXDET
Set bit to 0.
R/W
0x00
Set bits to 0.
1:0
Reserved
0x0F
CH0 - CHB0
EQ
7:0
EQ Control
R/W
0x2F
IB0 EQ Control - total of 256 levels.
See Table 2.
0x10
CH0 - CHB0
VOD
7
Short Circuit
Protection
R/W
0xAD
1: Enable the short circuit protection
0: Disable the short circuit protection
6
RATE_SEL
1: Gen 1/2,
0: Gen 3
Note: override the RATE pin.
5:3
Reserved
Set bits to default value - 101.
2:0
VOD Control
OB0 VOD Control
000: 0.7 V
001: 0.8 V
010: 0.9 V
011: 1.0 V
100: 1.1 V
101: 1.2 V (default)
110: 1.3 V
111: 1.4 V
24
Set bits to 0.
Submit Documentation Feedback
Copyright © 2011–2012, Texas Instruments Incorporated
Product Folder Links: DS80PCI800
DS80PCI800
www.ti.com
SNLS334E – APRIL 2011 – REVISED MARCH 2012
Table 9. SMBUS Slave Mode Register Map (continued)
Address
Register Name
Bit (s) Field
Type
Default
Description
0x11
CH0 - CHB0
DEM
7
RXDET STATUS
R
0x02
Observation bit for RXDET CH0 - CHB0.
1: RX = detected
0: RX = not detected
6:5
RATE_DET
STATUS
R
Observation bit for RATE_DET CH0 - CHB0.
00: GEN1 (2.5G)
01: GEN2 (5G)
11: GEN3 (8G)
4:3
Reserved
R/W
Set bits to 0.
2:0
DEM Control
R/W
OB0 DEM Control
000: 0 dB
001: –1.5 dB
010: –3.5 dB (default)
011: –5 dB
100: –6 dB
101: –8 dB
110: –9 dB
111: –12 dB
7:4
Reserved
R/W
3:2
IDLE thd
De-assert threshold
00 = 110 mVp-p (default)
01 = 100 mVp-p
10 = 150 mVp-p
11 = 130 mVp-p
Note: override the SD_TH pin.
1:0
IDLE tha
Assert threshold
00 = 180 mVp-p (default)
01 = 160 mVp-p
10 = 210 mVp-p
11 = 190 mVp-p
Note: override the SD_TH pin.
7:6
Reserved
5
IDLE_AUTO
1: Automatic IDLE detect
0: Allow IDLE_SEL control in bit 4
Note: override IDLE control.
4
IDLE_SEL
1: Output is MUTED (electrical idle)
0: Output is ON
Note: override IDLE control.
3:2
RXDET
00: Input is high-z impedance
01: Auto RX-Detect,
outputs test every 12 ms for 600 ms (50 times) then
stops; termination is high-z until detection; once
detected input termination is 50 Ω
10: Auto RX-Detect,
outputs test every 12 ms until detection occurs;
termination is high-z until detection; once detected
input termination is 50 Ω
11: Input is 50 Ω
Note: override RXDET pin.
1:0
Reserved
7:0
EQ Control
0x12
0x15
0x16
CH0 - CHB0
IDLE Threshold
CH1 - CHB1
IDLE, RXDET
CH1 - CHB1
EQ
R/W
0x00
0x00
Set bits to 0.
Set bits to 0.
Set bits to 0.
R/W
0x2F
IB1 EQ Control - total of 256 levels.
See Table 2.
Submit Documentation Feedback
Copyright © 2011–2012, Texas Instruments Incorporated
Product Folder Links: DS80PCI800
25
DS80PCI800
SNLS334E – APRIL 2011 – REVISED MARCH 2012
www.ti.com
Table 9. SMBUS Slave Mode Register Map (continued)
Address
Register Name
Bit (s) Field
Type
Default
Description
0x17
CH1 - CHB1
VOD
7
Short Circuit
Protection
R/W
0xAD
1: Enable the short circuit protection
0: Disable the short circuit protection
6
RATE_SEL
1: Gen 1/2,
0: Gen 3
Note: override the RATE pin.
5:3
Reserved
Set bits to default value - 101.
2:0
VOD Control
OB1 VOD Control
000: 0.7 V
001: 0.8 V
010: 0.9 V
011: 1.0 V
100: 1.1 V
101: 1.2 V (default)
110: 1.3 V
111: 1.4 V
7
RXDET STATUS
R
6:5
RATE_DET
STATUS
R
Observation bit for RATE_DET CH1 - CHB1.
00: GEN1 (2.5G)
01: GEN2 (5G)
11: GEN3 (8G)
4:3
Reserved
R/W
Set bits to 0.
2:0
DEM Control
R/W
OB1 DEM Control
000: 0 dB
001: –1.5 dB
010: –3.5 dB (default)
011: –5 dB
100: –6 dB
101: –8 dB
110: –9 dB
111: –12 dB
7:4
Reserved
R/W
3:2
IDLE thd
De-assert threshold
00 = 110 mVp-p (default)
01 = 100 mVp-p
10 = 150 mVp-p
11 = 130 mVp-p
Note: override the SD_TH pin.
1:0
IDLE tha
Assert threshold
00 = 180 mVp-p (default)
01 = 160 mVp-p
10 = 210 mVp-p
11 = 190 mVp-p
Note: override the SD_TH pin.
0x18
0x19
26
CH1 - CHB1
DEM
CH1 - CHB1
IDLE Threshold
0x02
0x00
Submit Documentation Feedback
Observation bit for RXDET CH1 - CHB1.
1: RX = detected
0: RX = not detected
Set bits to 0.
Copyright © 2011–2012, Texas Instruments Incorporated
Product Folder Links: DS80PCI800
DS80PCI800
www.ti.com
SNLS334E – APRIL 2011 – REVISED MARCH 2012
Table 9. SMBUS Slave Mode Register Map (continued)
Address
Register Name
Bit (s) Field
Type
Default
Description
0x1C
CH2 - CHB2
IDLE, RXDET
7:6
Reserved
R/W
0x00
Set bits to 0.
5
IDLE_AUTO
1: Automatic IDLE detect
0: Allow IDLE_SEL control in bit 4
Note: override IDLE control.
4
IDLE_SEL
1: Output is MUTED (electrical idle)
0: Output is ON
Note: override IDLE control.
3:2
RXDET
00: Input is high-z impedance
01: Auto RX-Detect,
outputs test every 12 ms for 600 ms (50 times) then
stops; termination is high-z until detection; once
detected input termination is 50 Ω
10: Auto RX-Detect,
outputs test every 12 ms until detection occurs;
termination is high-z until detection; once detected
input termination is 50 Ω
11: Input is 50 Ω
Note: override RXDET pin.
1:0
Reserved
0x1D
CH2 - CHB2
EQ
7:0
EQ Control
R/W
0x2F
IB2 EQ Control - total of 256 levels.
See Table 2.
0x1E
CH2 - CHB2
VOD
7
Short Circuit
Protection
R/W
0xAD
1: Enable the short circuit protection
0: Disable the short circuit protection
6
RATE_SEL
1: Gen 1/2,
0: Gen 3
Note: override the RATE pin.
5:3
Reserved
Set bits to default value - 101.
2:0
VOD Control
OB2 VOD Control
000: 0.7 V
001: 0.8 V
010: 0.9 V
011: 1.0 V
100: 1.1 V
101: 1.2 V (default)
110: 1.3 V
111: 1.4 V
7
RXDET STATUS
R
6:5
RATE_DET
STATUS
R
Observation bit for RATE_DET CH2 - CHB2.
00: GEN1 (2.5G)
01: GEN2 (5G)
11: GEN3 (8G)
4:3
Reserved
R/W
Set bits to 0.
2:0
DEM Control
R/W
OB2 DEM Control
000: 0 dB
001: –1.5 dB
010: –3.5 dB (default)
011: –5 dB
100: –6 dB
101: –8 dB
110: –9 dB
111: –12 dB
0x1F
CH2 - CHB2
DEM
Set bits to 0.
0x02
Observation bit for RXDET CH2 - CHB2.
1: RX = detected
0: RX = not detected
Submit Documentation Feedback
Copyright © 2011–2012, Texas Instruments Incorporated
Product Folder Links: DS80PCI800
27
DS80PCI800
SNLS334E – APRIL 2011 – REVISED MARCH 2012
www.ti.com
Table 9. SMBUS Slave Mode Register Map (continued)
Address
Register Name
Bit (s) Field
Type
Default
Description
0x20
CH2 - CHB2
IDLE Threshold
7:4
Reserved
R/W
0x00
Set bits to 0.
3:2
IDLE thd
De-assert threshold
00 = 110 mVp-p (default)
01 = 100 mVp-p
10 = 150 mVp-p
11 = 130 mVp-p
Note: override the SD_TH pin.
1:0
IDLE tha
Assert threshold
00 = 180 mVp-p (default)
01 = 160 mVp-p
10 = 210 mVp-p
11 = 190 mVp-p
Note: override the SD_TH pin.
7:6
Reserved
5
IDLE_AUTO
1: Automatic IDLE detect
0: Allow IDLE_SEL control in bit 4
Note: override IDLE control.
4
IDLE_SEL
1: Output is MUTED (electrical idle)
0: Output is ON
Note: override IDLE control.
3:2
RXDET
00: Input is high-z impedance
01: Auto RX-Detect,
outputs test every 12 ms for 600 ms (50 times) then
stops; termination is high-z until detection; once
detected input termination is 50 Ω
10: Auto RX-Detect,
outputs test every 12 ms until detection occurs;
termination is high-z until detection; once detected
input termination is 50 Ω
11: Input is 50 Ω
Note: override RXDET pin.
0x23
CH3 - CHB3
IDLE, RXDET
R/W
0x00
Set bits to 0.
1:0
Reserved
0x24
CH3 - CHB3
EQ
7:0
EQ Control
R/W
0x2F
IB3 EQ Control - total of 256 levels.
See Table 2.
0x25
CH3 - CHB3
VOD
7
Short Circuit
Protection
R/W
0xAD
1: Enable the short circuit protection
0: Disable the short circuit protection
6
RATE_SEL
1: Gen 1/2,
0: Gen 3
Note: override the RATE pin.
5:3
Reserved
Set bits to default value - 101.
2:0
VOD Control
OB0 VOD Control
000: 0.7 V
001: 0.8 V
010: 0.9 V
011: 1.0 V
100: 1.1 V
101: 1.2 V (default)
110: 1.3 V
111: 1.4 V
28
Set bits to 0.
Submit Documentation Feedback
Copyright © 2011–2012, Texas Instruments Incorporated
Product Folder Links: DS80PCI800
DS80PCI800
www.ti.com
SNLS334E – APRIL 2011 – REVISED MARCH 2012
Table 9. SMBUS Slave Mode Register Map (continued)
Address
Register Name
Bit (s) Field
Type
Default
Description
0x26
CH3 - CHB3
DEM
7
RXDET STATUS
R
0x02
Observation bit for RXDET CH3 - CHB3.
1: RX = detected
0: RX = not detected
6:5
RATE_DET
STATUS
R
Observation bit for RATE_DET CH3 - CHB3.
00: GEN1 (2.5G)
01: GEN2 (5G)
11: GEN3 (8G)
4:3
Reserved
R/W
Set bits to 0.
2:0
DEM Control
R/W
OB3 DEM Control
000: 0 dB
001: –1.5 dB
010: –3.5 dB (default)
011: –5 dB
100: –6 dB
101: –8 dB
110: –9 dB
111: –12 dB
7:4
Reserved
R/W
3:2
IDLE thd
De-assert threshold
00 = 110 mVp-p (default)
01 = 100 mVp-p
10 = 150 mVp-p
11 = 130 mVp-p
Note: override the SD_TH pin.
1:0
IDLE tha
Assert threshold
00 = 180 mVp-p (default)
01 = 160 mVp-p
10 = 210 mVp-p
11 = 190 mVp-p
Note: override the SD_TH pin.
7:6
Reserved
5
IDLE_AUTO
1: Automatic IDLE detect
0: Allow IDLE_SEL control in bit 4
Note: override IDLE control.
4
IDLE_SEL
1: Output is MUTED (electrical idle)
0: Output is ON
Note: override IDLE control.
3:2
RXDET
00: Input is high-z impedance
01: Auto RX-Detect,
outputs test every 12 ms for 600 ms (50 times) then
stops; termination is high-z until detection; once
detected input termination is 50 Ω
10: Auto RX-Detect,
outputs test every 12 ms until detection occurs;
termination is high-z until detection; once detected
input termination is 50 Ω
11: Input is 50 Ω
Note: override RXDET pin.
1:0
Reserved
7:0
EQ Control
0x27
0x2B
0x2C
CH3 - CHB3
IDLE Threshold
CH4 - CHA0
IDLE, RXDET
CH4 - CHA0
EQ
R/W
0x00
0x00
Set bits to 0.
Set bits to 0.
Set bits to 0.
R/W
0x2F
IA0 EQ Control - total of 256 levels.
See Table 2.
Submit Documentation Feedback
Copyright © 2011–2012, Texas Instruments Incorporated
Product Folder Links: DS80PCI800
29
DS80PCI800
SNLS334E – APRIL 2011 – REVISED MARCH 2012
www.ti.com
Table 9. SMBUS Slave Mode Register Map (continued)
Address
Register Name
Bit (s) Field
Type
Default
Description
0x2D
CH4 - CHA0
VOD
7
Short Circuit
Protection
R/W
0xAD
1: Enable the short circuit protection
0: Disable the short circuit protection
6
RATE_SEL
1: Gen 1/2,
0: Gen 3
Note: override the RATE pin.
5:3
Reserved
Set bits to default value - 101.
2:0
VOD Control
OA0 VOD Control
000: 0.7 V
001: 0.8 V
010: 0.9 V
011: 1.0 V
100: 1.1 V
101: 1.2 V (default)
110: 1.3 V
111: 1.4 V
7
RXDET STATUS
R
6:5
RATE_DET
STATUS
R
Observation bit for RATE_DET CH4 - CHA0.
00: GEN1 (2.5G)
01: GEN2 (5G)
11: GEN3 (8G)
4:3
Reserved
R/W
Set bits to 0.
2:0
DEM Control
R/W
OA0 DEM Control
000: 0 dB
001: –1.5 dB
010: –3.5 dB (default)
011: –5 dB
100: –6 dB
101: –8 dB
110: –9 dB
111: –12 dB
7:4
Reserved
R/W
3:2
IDLE thd
De-assert threshold
00 = 110 mVp-p (default)
01 = 100 mVp-p
10 = 150 mVp-p
11 = 130 mVp-p
Note: override the SD_TH pin.
1:0
IDLE tha
Assert threshold
00 = 180 mVp-p (default)
01 = 160 mVp-p
10 = 210 mVp-p
11 = 190 mVp-p
Note: override the SD_TH pin.
0x2E
0x2F
30
CH4 - CHA0
DEM
CH4 - CHA0
IDLE Threshold
0x02
0x00
Submit Documentation Feedback
Observation bit for RXDET CH4 - CHA0.
1: RX = detected
0: RX = not detected
Set bits to 0.
Copyright © 2011–2012, Texas Instruments Incorporated
Product Folder Links: DS80PCI800
DS80PCI800
www.ti.com
SNLS334E – APRIL 2011 – REVISED MARCH 2012
Table 9. SMBUS Slave Mode Register Map (continued)
Address
Register Name
Bit (s) Field
Type
Default
Description
0x32
CH5 - CHA1
IDLE, RXDET
7:6
Reserved
R/W
0x00
Set bits to 0.
5
IDLE_AUTO
1: Automatic IDLE detect
0: Allow IDLE_SEL control in bit 4
Note: override IDLE control.
4
IDLE_SEL
1: Output is MUTED (electrical idle)
0: Output is ON
Note: override IDLE control.
3:2
RXDET
00: Input is high-z impedance
01: Auto RX-Detect,
outputs test every 12 ms for 600 ms (50 times) then
stops; termination is high-z until detection; once
detected input termination is 50 Ω
10: Auto RX-Detect,
outputs test every 12 ms until detection occurs;
termination is high-z until detection; once detected
input termination is 50 Ω
11: Input is 50 Ω
Note: override RXDET pin.
1:0
Reserved
0x33
CH5 - CHA1
EQ
7:0
EQ Control
R/W
0x2F
IA1 EQ Control - total of 256 levels.
See Table 2.
0x34
CH5 - CHA1
VOD
7
Short Circuit
Protection
R/W
0xAD
1: Enable the short circuit protection
0: Disable the short circuit protection
6
RATE_SEL
1: Gen 1/2,
0: Gen 3
Note: override the RATE pin.
5:3
Reserved
Set bits to default value - 101.
2:0
VOD Control
OA1 VOD Control
000: 0.7 V
001: 0.8 V
010: 0.9 V
011: 1.0 V
100: 1.1 V
101: 1.2 V (default)
110: 1.3 V
111: 1.4 V
7
RXDET STATUS
R
6:5
RATE_DET
STATUS
R
Observation bit for RATE_DET CH5 - CHA1.
00: GEN1 (2.5G)
01: GEN2 (5G)
11: GEN3 (8G)
4:3
Reserved
R/W
Set bits to 0.
2:0
DEM Control
R/W
OA1 DEM Control
000: 0 dB
001: –1.5 dB
010: –3.5 dB (default)
011: –5 dB
100: –6 dB
101: –8 dB
110: –9 dB
111: –12 dB
0x35
CH5 - CHA1
DEM
Set bits to 0.
0x02
Observation bit for RXDET CH5 - CHA1.
1: RX = detected
0: RX = not detected
Submit Documentation Feedback
Copyright © 2011–2012, Texas Instruments Incorporated
Product Folder Links: DS80PCI800
31
DS80PCI800
SNLS334E – APRIL 2011 – REVISED MARCH 2012
www.ti.com
Table 9. SMBUS Slave Mode Register Map (continued)
Address
Register Name
Bit (s) Field
Type
Default
Description
0x36
CH5 - CHA1
IDLE Threshold
7:4
Reserved
R/W
0x00
Set bits to 0.
3:2
IDLE thd
De-assert threshold
00 = 110 mVp-p (default)
01 = 100 mVp-p
10 = 150 mVp-p
11 = 130 mVp-p
Note: override the SD_TH pin.
1:0
IDLE tha
Assert threshold
00 = 180 mVp-p (default)
01 = 160 mVp-p
10 = 210 mVp-p
11 = 190 mVp-p
Note: override the SD_TH pin.
7:6
Reserved
5
IDLE_AUTO
1: Automatic IDLE detect
0: Allow IDLE_SEL control in bit 4
Note: override IDLE control.
4
IDLE_SEL
1: Output is MUTED (electrical idle)
0: Output is ON
Note: override IDLE control.
3:2
RXDET
00: Input is high-z impedance
01: Auto RX-Detect,
outputs test every 12 ms for 600 ms (50 times) then
stops; termination is high-z until detection; once
detected input termination is 50 Ω
10: Auto RX-Detect,
outputs test every 12 ms until detection occurs;
termination is high-z until detection; once detected
input termination is 50 Ω
11: Input is 50 Ω
Note: override RXDET pin.
0x39
CH6 - CHA2
IDLE, RXDET
R/W
0x00
Set bits to 0.
1:0
Reserved
0x3A
CH6 - CHA2
EQ
7:0
EQ Control
R/W
0x2F
IA2 EQ Control - total of 256 levels.
See Table 2.
0x3B
CH6 - CHA2
VOD
7
Short Circuit
Protection
R/W
0xAD
1: Enable the short circuit protection
0: Disable the short circuit protection
6
RATE_SEL
1: Gen 1/2,
0: Gen 3
Note: override the RATE pin.
5:3
Reserved
Set bits to default value - 101.
2:0
VOD Control
OA2 VOD Control
000: 0.7 V
001: 0.8 V
010: 0.9 V
011: 1.0 V
100: 1.1 V
101: 1.2 V (default)
110: 1.3 V
111: 1.4 V
32
Set bits to 0.
Submit Documentation Feedback
Copyright © 2011–2012, Texas Instruments Incorporated
Product Folder Links: DS80PCI800
DS80PCI800
www.ti.com
SNLS334E – APRIL 2011 – REVISED MARCH 2012
Table 9. SMBUS Slave Mode Register Map (continued)
Address
Register Name
Bit (s) Field
Type
Default
Description
0x3C
CH6 - CHA2
DEM
7
RXDET STATUS
R
0x02
Observation bit for RXDET CH6 - CHA2.
1: RX = detected
0: RX = not detected
6:5
RATE_DET
STATUS
R
Observation bit for RATE_DET CH6 - CHA2.
00: GEN1 (2.5G)
01: GEN2 (5G)
11: GEN3 (8G)
4:3
Reserved
R/W
Set bits to 0.
2:0
DEM Control
R/W
OA2 DEM Control
000: 0 dB
001: –1.5 dB
010: –3.5 dB (default)
011: –5 dB
100: –6 dB
101: –8 dB
110: –9 dB
111: –12 dB
7:4
Reserved
R/W
3:2
IDLE thd
De-assert threshold
00 = 110 mVp-p (default)
01 = 100 mVp-p
10 = 150 mVp-p
11 = 130 mVp-p
Note: override the SD_TH pin.
1:0
IDLE tha
Assert threshold
00 = 180 mVp-p (default)
01 = 160 mVp-p
10 = 210 mVp-p
11 = 190 mVp-p
Note: override the SD_TH pin.
7:6
Reserved
5
IDLE_AUTO
1: Automatic IDLE detect
0: Allow IDLE_SEL control in bit 4
Note: override IDLE control.
4
IDLE_SEL
1: Output is MUTED (electrical idle)
0: Output is ON
Note: override IDLE control.
3:2
RXDET
00: Input is high-z impedance
01: Auto RX-Detect,
outputs test every 12 ms for 600 ms (50 times) then
stops; termination is high-z until detection; once
detected input termination is 50 Ω
10: Auto RX-Detect,
outputs test every 12 ms until detection occurs;
termination is high-z until detection; once detected
input termination is 50 Ω
11: Input is 50 Ω
Note: override RXDET pin.
1:0
Reserved
7:0
EQ Control
0x3D
0x40
0x41
CH6 - CHA2
IDLE Threshold
CH7 - CHA3
IDLE, RXDET
CH7 - CHA3
EQ
R/W
0x00
0x00
Set bits to 0.
Set bits to 0.
Set bits to 0.
R/W
0x2F
IA3 EQ Control - total of 256 levels.
See Table 2.
Submit Documentation Feedback
Copyright © 2011–2012, Texas Instruments Incorporated
Product Folder Links: DS80PCI800
33
DS80PCI800
SNLS334E – APRIL 2011 – REVISED MARCH 2012
www.ti.com
Table 9. SMBUS Slave Mode Register Map (continued)
Address
Register Name
Bit (s) Field
Type
Default
Description
0x42
CH7 - CHA3
VOD
7
Short Circuit
Protection
R/W
0xAD
1: Enable the short circuit protection
0: Disable the short circuit protection
6
RATE_SEL
1: Gen 1/2,
0: Gen 3
Note: override the RATE pin.
5:3
Reserved
Set bits to default value - 101.
2:0
VOD Control
OA3 VOD Control
000: 0.7 V
001: 0.8 V
010: 0.9 V
011: 1.0 V
100: 1.1 V
101: 1.2 V (default)
110: 1.3 V
111: 1.4 V
7
RXDET STATUS
R
6:5
RATE_DET
STATUS
R
Observation bit for RATE_DET CH7 - CHA3.
00: GEN1 (2.5G)
01: GEN2 (5G)
11: GEN3 (8G)
4:3
Reserved
R/W
Set bits to 0.
2:0
DEM Control
R/W
OA3 DEM Control
000: 0 dB
001: –1.5 dB
010: –3.5 dB (default)
011: –5 dB
100: –6 dB
101: –8 dB
110: –9 dB
111: –12 dB
7:4
Reserved
R/W
3:2
IDLE thd
De-assert threshold
00 = 110 mVp-p (default)
01 = 100 mVp-p
10 = 150 mVp-p
11 = 130 mVp-p
Note: override the SD_TH pin.
1:0
IDLE tha
Assert threshold
00 = 180 mVp-p (default)
01 = 160 mVp-p
10 = 210 mVp-p
11 = 190 mVp-p
Note: override the SD_TH pin.
7:5
VERSION
4:0
ID
0x43
0x44
0x51
CH7 - CHA3
DEM
CH7 - CHA3
IDLE Threshold
Device ID
R
0x02
0x00
0x45
Observation bit for RXDET CH7 - CHA3.
1: RX = detected
0: RX = not detected
Set bits to 0.
010'b
00101'b
Applications Information
GENERAL RECOMMENDATIONS
The DS80PCI800 is a high performance circuit capable of delivering excellent performance. Careful attention
must be paid to the details associated with high-speed design as well as providing a clean power supply. Refer
to the information below and Revision 4 of the LVDS Owner's Manual for more detailed information on high
speed design tips to address signal integrity design issues.
34
Submit Documentation Feedback
Copyright © 2011–2012, Texas Instruments Incorporated
Product Folder Links: DS80PCI800
DS80PCI800
www.ti.com
SNLS334E – APRIL 2011 – REVISED MARCH 2012
PCB LAYOUT CONSIDERATIONS FOR DIFFERENTIAL PAIRS
The CML inputs and LPDS outputs have been optimized to work with interconnects using a controlled differential
impedance of 85 - 100Ω. It is preferable to route differential lines exclusively on one layer of the board,
particularly for the input traces. The use of vias should be avoided if possible. If vias must be used, they should
be used sparingly and must be placed symmetrically for each side of a given differential pair. Whenever
differential vias are used the layout must also provide for a low inductance path for the return currents as well.
Route the differential signals away from other signals and noise sources on the printed circuit board. See AN1187 for additional information on LLP packages.
20 mils
EXTERNAL MICROSTRIP
100 mils
20 mils
INTERNAL STRIPLINE
VDD
VDD
18 17 16 15 14 13 12 11 10
9
8
7
6
5
4
3
2
1
19
54
20
53
21
52
51
22
BOTTOM OF PKG
23
VDD
50
GND
24
49
25
48
26
47
27
46
28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45
VDD
VDD
Figure 7. Typical Routing Options
The graphic shown above depicts different transmission line topologies which can be used in various
combinations to achieve the optimal system performance. Impedance discontinuities at the differential via can be
minimized or eliminated by increasing the swell around each hole and providing for a low inductance return
current path. When the via structure is associated with thick backplane PCB, further optimization such as back
drilling is often used to reduce the deterimential high frequency effects of stubs on the signal path.
Submit Documentation Feedback
Copyright © 2011–2012, Texas Instruments Incorporated
Product Folder Links: DS80PCI800
35
DS80PCI800
SNLS334E – APRIL 2011 – REVISED MARCH 2012
www.ti.com
POWER SUPPLY BYPASSING
Two approaches are recommended to ensure that the DS80PCI800 is provided with an adequate power supply.
First, the supply (VDD) and ground (GND) pins should be connected to power planes routed on adjacent layers
of the printed circuit board. The layer thickness of the dielectric should be minimized so that the VDD and GND
planes create a low inductance supply with distributed capacitance. Second, careful attention to supply
bypassing through the proper use of bypass capacitors is required. A 0.1 μF bypass capacitor should be
connected to each VDD pin such that the capacitor is placed as close as possible to the DS80PCI800. Smaller
body size capacitors can help facilitate proper component placement. Additionally, capacitor with capacitance in
the range of 1 μF to 10 μF should be incorporated in the power supply bypassing design as well. These
capacitors can be either tantalum or an ultra-low ESR ceramic.
Typical Performance Curves Characteristics
640.0
VDD = 2.625V
620.0
VDD = 2.5V
600.0
VDD = 2.375V
PD (mW)
580.0
560.0
540.0
520.0
500.0
480.0
T = 25oC
460.0
440.0
420.0
0.8
0.9
1
1.1
1.2
1.3
VOD (Vp-p)
Figure 8. Power Dissipation (PD) vs. Output Differential Voltage (VOD)
1021
T = 25°C
VOD (mVp-p)
1019
1016
1013
1010
1007
2.375
2.5
2.625
VDD (V)
Figure 9. Output Differential Voltage (VOD = 1.0 Vp-p) vs. Supply Voltage (VDD)
36
Submit Documentation Feedback
Copyright © 2011–2012, Texas Instruments Incorporated
Product Folder Links: DS80PCI800
DS80PCI800
www.ti.com
SNLS334E – APRIL 2011 – REVISED MARCH 2012
1020
VDD = 2.5 V
VOD (mVp-p)
1018
1016
1014
1012
- 40
-15
10
35
60
85
TEMPERATURE (°C)
Figure 10. Output Differential Voltage (VOD = 1.0 Vp-p) vs. Temperature
Typical Performance Eye Diagrams Characteristics
Pattern
Generator
VID = 1.0 Vp-p,
DE = 0 dB
8 Gb/s, PRBS23
TL
Lossy Channel
IN
DS80PCI800
Scope
BW = 50 GHz
OUT
Figure 11. Test Setup Connections Diagram
Figure 12. TL = 20 inch 4–mil FR4 trace,
DS80PCI800 settings: EQ[1:0] = R, R = 15'h, DEM[1:0] = float, float
Submit Documentation Feedback
Copyright © 2011–2012, Texas Instruments Incorporated
Product Folder Links: DS80PCI800
37
DS80PCI800
SNLS334E – APRIL 2011 – REVISED MARCH 2012
www.ti.com
Figure 13. TL = 35 inch 4–mil FR4 trace,
DS80PCI800 settings: EQ[1:0] = float, R = 1F'h, DEM[1:0] = float, float
Pattern
Generator
VID = 1.0 Vp-p,
DE = -9 dB
8 Gb/s, PRBS23
TL1
Lossy Channel
IN
DS80PCI800
OUT
TL2
Lossy Channel
Scope
BW = 50 GHz
Figure 14. Test Setup Connections Diagram
Figure 15. TL1 = 20 inch 4–mil FR4 trace, TL2 = 15 inch 4–mil FR4 trace,
DS80PCI800 settings: EQ[1:0] = R, R = 15'h, DEM[1:0] = float, float
Figure 16. TL1 = 30 inch 4–mil FR4 trace, TL2 = 15 inch 4–mil FR4 trace,
DS80PCI800 settings: EQ[1:0] = R, 1 = 0F'h, DEM[1:0] = float, float
38
Submit Documentation Feedback
Copyright © 2011–2012, Texas Instruments Incorporated
Product Folder Links: DS80PCI800
PACKAGE OPTION ADDENDUM
www.ti.com
11-Apr-2013
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
(2)
MSL Peak Temp
Op Temp (°C)
Top-Side Markings
(3)
(4)
DS80PCI800SQ/NOPB
ACTIVE
WQFN
NJY
54
2000
Green (RoHS
& no Sb/Br)
CU SN
Level-2-260C-1 YEAR
-40 to 85
DS80PCI800SQ
DS80PCI800SQE/NOPB
ACTIVE
WQFN
NJY
54
250
Green (RoHS
& no Sb/Br)
CU SN
Level-2-260C-1 YEAR
-40 to 85
DS80PCI800SQ
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
Multiple Top-Side Markings will be inside parentheses. Only one Top-Side Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a
continuation of the previous line and the two combined represent the entire Top-Side Marking for that device.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
Samples
PACKAGE MATERIALS INFORMATION
www.ti.com
26-Mar-2013
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
DS80PCI800SQ/NOPB
WQFN
NJY
54
2000
330.0
16.4
5.8
10.3
1.0
12.0
16.0
Q1
DS80PCI800SQE/NOPB
WQFN
NJY
54
250
178.0
16.4
5.8
10.3
1.0
12.0
16.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
26-Mar-2013
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
DS80PCI800SQ/NOPB
WQFN
NJY
54
2000
367.0
367.0
38.0
DS80PCI800SQE/NOPB
WQFN
NJY
54
250
213.0
191.0
55.0
Pack Materials-Page 2
PACKAGE OUTLINE
NJY0054A
WQFN
SCALE 2.000
WQFN
5.6
5.4
B
A
PIN 1 INDEX AREA
0.5
0.3
0.3
0.2
10.1
9.9
DETAIL
OPTIONAL TERMINAL
TYPICAL
0.8 MAX
C
SEATING PLANE
2X 4
SEE TERMINAL
DETAIL
3.51±0.1
19
(0.1)
27
28
18
50X 0.5
7.5±0.1
2X
8.5
1
45
54
PIN 1 ID
(OPTIONAL)
46
54X
54X
0.5
0.3
0.3
0.2
0.1
0.05
C A
C
B
4214993/A 07/2013
NOTES:
1. All linear dimensions are in millimeters. Dimensions in parenthesis are for reference only. Dimensioning and tolerancing per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. The package thermal pad must be soldered to the printed circuit board for thermal and mechanical performance.
www.ti.com
EXAMPLE BOARD LAYOUT
NJY0054A
WQFN
WQFN
(3.51)
SYMM
54X (0.6)
54
54X (0.25)
SEE DETAILS
46
1
45
50X (0.5)
(7.5)
SYMM
(9.8)
(1.17)
TYP
2X
(1.16)
28
18
( 0.2) TYP
VIA
19
27
(1) TYP
(5.3)
LAND PATTERN EXAMPLE
SCALE:8X
0.07 MIN
ALL AROUND
0.07 MAX
ALL AROUND
METAL
SOLDER MASK
OPENING
SOLDER MASK
OPENING
NON SOLDER MASK
DEFINED
(PREFERRED)
METAL
SOLDER MASK
DEFINED
SOLDER MASK DETAILS
4214993/A 07/2013
NOTES: (continued)
4. This package is designed to be soldered to a thermal pad on the board. For more information, refer to QFN/SON PCB application note
in literature No. SLUA271 (www.ti.com/lit/slua271).
www.ti.com
EXAMPLE STENCIL DESIGN
NJY0054A
WQFN
WQFN
SYMM
METAL
TYP
(0.855) TYP
46
54
54X (0.6)
54X (0.25)
1
45
50X (0.5)
(1.17)
TYP
SYMM
(9.8)
12X (0.97)
18
28
19
27
12X (1.51)
(5.3)
SOLDERPASTE EXAMPLE
BASED ON 0.125mm THICK STENCIL
EXPOSED PAD
67% PRINTED SOLDER COVERAGE BY AREA
SCALE:10X
4214993/A 07/2013
NOTES: (continued)
5. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
www.ti.com
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated