SN65LVPE502CP SLLSE79B – MARCH 2011 – REVISED FEBRUARY 2012 www.ti.com Dual Channel USB3.0 Redriver/Equalizer Check for Samples: SN65LVPE502CP FEATURES • 1 • • • • • • • • Single Lane USB 3.0 Equalizer/Redriver Selectable Equalization, De-Emphasis and Output Swing Control Integrated Termination Hot-Plug Capable Low Active Power (U0 state) – 315 mW (TYP), VCC = 3.3V USB 3.0 Low Power Support – 7 mW (TYP) When no Connection Detected – 70 mW (TYP) When Link in U2/U3 Mode Excellent Jitter and Loss Compensation Capability: – >40" of Total 4 mil Stripline on FR4 Small Foot Print – 24 Pin (4mm x 4mm) QFN Package High Protection Against ESD Transient – HBM: 5,000 V – CDM: 1,500 V – MM: 200 V APPLICATIONS • Notebooks, Desktops, Docking Stations, Active Cable, Backplane and Active Cable DESCRIPTION The SN65LVPE502CP is a dual channel, single lane USB 3.0 redriver and signal conditioner supporting data rates of 5.0Gbps. The device complies with USB 3.0 spec revision 1.0, supporting electrical idle condition and low frequency periodic signals (LFPS) for USB 3.0 power management modes. SPACER Main PCB Redriver USB Host USB Connector 20" Main PCB USB Host Connector Device PCB Device Redriver 20" 3m USB 3.0 Cable 1"-6" Figure 1. Typical Application 1 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2011–2012, Texas Instruments Incorporated SN65LVPE502CP SLLSE79B – MARCH 2011 – REVISED FEBRUARY 2012 www.ti.com These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. EN_RXD RX1+ RX1- Dual Termination Detect TX1+ Receiver/ Equalizer CHANNEL 1 Driver TX1- EQ1 EQ CNTRL EQ2 DE1 VTX_CM_DC DEMP CNTRL DE2 CHANNEL 2 Driver Dual Termination TX2+ Receiver/ Equalizer TX2- Detect VTX_CM_DC OS Cntrl. RX2+ RX2- EN_RXD OS1 OS2 Figure 2. Data Flow Block Diagram ORDERING INFORMATION (1) (1) 2 PART NUMBER PART MARKING PACKAGE SN65LVPE502CPRGER 502CP 24-pin RGE Reel (Large) SN65LVPE502CPRGET 502CP 24-pin RGE Reel (Small) For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI web site at www.ti.com. Submit Documentation Feedback Copyright © 2011–2012, Texas Instruments Incorporated Product Folder Link(s): SN65LVPE502CP SN65LVPE502CP SLLSE79B – MARCH 2011 – REVISED FEBRUARY 2012 www.ti.com ABSOLUTE MAXIMUM RATINGS (1) over operating free-air temperature range (unless otherwise noted) VALUE Supply voltage range (2) Voltage range MAX VCC –0.5 4 V Differential I/O –0.5 4 V Control I/O –0.5 VCC + 0.5 V (3) ±5000 V Charged-device model (4) ±1500 V Machine model (5) ±200 V Human body model Electrostatic discharge Continuous power dissipation (1) (2) (3) (4) (5) UNIT MIN See Thermal Table Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any conditions beyond those indicated under recommended operating conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. All voltage values, except differential voltages, are with respect to network ground terminal. Tested in accordance with JEDEC Standard 22, Test Method A114-B Tested in accordance with JEDEC Standard 22, Test Method C101-A Tested in accordance with JEDEC Standard 22, Test Method A115-A THERMAL INFORMATION SN65LVPE502CP THERMAL METRIC (1) RGE PACKAGE UNITS 24 PINS θJA Junction-to-ambient thermal resistance 46 θJCtop Junction-to-case (top) thermal resistance 42 θJB Junction-to-board thermal resistance 13 θJCbot Junction-to-case (bottom) thermal resistance 4 (1) °C/W For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953. THERMAL CHARACTERISTICS over recommended operating free-air temperature range (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX (1) UNIT PD Device power dissipation RSVD, EN_RXD, EQ cntrl pins = NC, K28.5 pattern at 5 Gbps, VID = 1000mVp-p 330 450 mW PSlp Device power dissipation in sleep mode EN_RXD= GND 0.3 1 mW (1) The maximum rating is simulated under 3.6V VCC. Device Power The SN65LVPE502CP is designed to operate from a single 3.3V supply. Submit Documentation Feedback Copyright © 2011–2012, Texas Instruments Incorporated Product Folder Link(s): SN65LVPE502CP 3 SN65LVPE502CP SLLSE79B – MARCH 2011 – REVISED FEBRUARY 2012 www.ti.com RECOMMENDED OPERATING CONDITIONS PARAMETER VCC Supply voltage CCOUPLING AC Coupling capacitor CONDITIONS MIN 3 Operating free-air temperature TYP MAX UNITS 3.6 V 75 3.3 200 nF 0 85 °C DEVICE PARAMETERS EN_RXD, RSVD, EQ cntrl = NC, K28.5 pattern at 5 Gbps, VID = 1000mVp-p ICC ICCRx.Detect Supply current ICCsleep 100 In Rx.Detect mode EN_RXD = GND ICCU2-U3 Link in USB low power state 120 2 5 0.01 0.1 21 Maximum data rate 5 tENB Device enable time Sleep mode exit time EN_RXD L → H With Rx termination present tDIS Device disable time Sleep mode entry time EN_RXD H → L TRX.DETECT Rx.Detect start event Power-up time mA Gbps 100 µs 2 µs 100 µs CONTROL LOGIC VIH High level input voltage 1.4 VCC V VIL Low level input voltage –0.3 0.5 V VHYS Input hysteresis 150 OSx, EQx, DEx = VCC IIH High level input current EN_RXD = VCC 1 RSVD = VCC IIL Low level input current 4 –30 EN_RXD = GND –30 Submit Documentation Feedback µA 30 OSx, EQx, DEx = GND RSVD = GND mV 30 µA –1 Copyright © 2011–2012, Texas Instruments Incorporated Product Folder Link(s): SN65LVPE502CP SN65LVPE502CP SLLSE79B – MARCH 2011 – REVISED FEBRUARY 2012 www.ti.com ELECTRICAL CHARACTERISTICS over recommended operating conditions (unless otherwise noted) PARAMETER CONDITIONS MIN TYP MAX UNITS 1200 mVp-p RECEIVER AC/DC Vindiff_p-p RX1, RX2 input voltage swing VCM_RX RX1, RX2 common mode voltage AC coupled differential RX peak to peak signal 100 VinCOM_P RX1, RX2 AC peak common mode voltage ZDC_RX DC common mode impedance 18 Zdiff_RX DC differential input impedance 72 50 85 3.3 Measured at Rx pins with termination enabled ZRX_High_IMP+ DC Input high impedance Device in sleep mode Rx termination not powered measured with respect to GND over 500mV max VRX-LFPS-DETpp Low voltage periodic signaling (LFPS) detect threshold Measured at receiver pin, below minimum output is squelched, above max input signal is passed to output RLRX-DIFF Differential return loss RLRX-CM Common mode return loss V 150 mVP 26 30 Ω 80 120 Ω 100 kΩ 300 50 MHz – 1.25 GHz 10 11 1.25 GH – 2.5 GHz 6 7 50 MHz– 2.5 GHz 11 13 800 1042 mVpp dB dB TRANSMITTER AC/DC RL = 100 Ω ±1%, DEx, OSx = NC, Transition Bit VTXDIFF_TB_P-P Differential peak-to-peak output voltage (VID = 800, 1200 mVpp, 5Gbps) VTXDIFF_NTB_P-P RL = 100 Ω ±1%, DEx = NC, OSx = GND Transition Bit 908 RL = 100 Ω ±1%, DEx = NC, OSx = VCC Transition Bit 1127 RL = 100 Ω ±1%, DEx=NC, OSx = 0,1,NC Non-Transition Bit 1042 RL = 100 Ω ±1%, DEx=0 OSx = 0,1,NC Non-Transition Bit 661 RL = 100 Ω ±1%, DEx=1 OSx = 0,1,NC Non-Transition Bit 507 DE1/DE2 = NC DE De-emphasis level OS1,2 = NC (for OS1, 2 = 1 and 0 see Table 2) De-emphasis width Zdiff_TX DC differential impedance ZCM_TX DC common mode impedance mV mV 0 –3.0 DE1/DE2 = 0 –3.5 –4.0 dB –6.0 DE1/DE2 = 1 TDE 1200 0.85 UI 72 90 120 Ω 18 23 30 Ω f = 50 MHz – 1.25 GHz 9 10 f = 1.25 GHz – 2.5 GHz 6 7 11 12 Measured w.r.t to AC ground over 0-500mV RLdiff_TX Differential return loss dB RLCM_TX Common mode return loss f = 50 MHz – 2.5 GHz ITX_SC TX short circuit current TX± shorted to GND VTX_CM_DC Transmitter DC common-mode voltage VTX_CM_AC_Active TX AC common mode voltage active VTX_idle_diff-AC-pp Electrical idle differential peak to peak output voltage VTX_CM_DeltaU1-U0 Absolute delta of DC CM voltage during active and idle states VTX_idle_diff-DC DC Electrical idle differential output voltage Voltage must be low pass filtered to remove any AC component Vdetect Voltage change to allow receiver detect Positive voltage to sense receiver termination tR, tF Output rise/fall time 20%–80% of differential voltage measured 1" from the output pin tRF_MM Output rise/fall time mismatch 20%–80% of differential voltage measured 1" from the output pin 1.5 20 ps Tdiff_LH, Tdiff_HL Differential propagation delay De-Emphasis = –3.5 dB (CH 0 and CH 1). Propagation delay between 50% level at input and output 305 370 ps tidleEntry, tidleExit Idle entry and exit times See Figure 4 4 6 CTX Tx input capacitance to GND At 2.5 GHz dB 60 2.0 HPF to remove DC 2.6 3.0 V 30 100 mVpp 10 mVpp 200 mV 10 mV 600 mV 0 35 0 30 65 ps 1.25 Submit Documentation Feedback Copyright © 2011–2012, Texas Instruments Incorporated Product Folder Link(s): SN65LVPE502CP mA ns pF 5 SN65LVPE502CP SLLSE79B – MARCH 2011 – REVISED FEBRUARY 2012 www.ti.com ELECTRICAL CHARACTERISTICS (continued) over recommended operating conditions (unless otherwise noted) PARAMETER CONDITIONS MIN TYP MAX 0.23 0.5 0.14 0.3 Random jitter (Rj) 0.08 0.2 Total jitter (Tj) at point B 0.15 0.5 0.07 0.3 0.08 0.2 UNITS EQUALIZATION TTX-EYE (1) (2) DJTX (2) RJTX (2) (4) TTX-EYE Total jitter (Tj) at point A (1) (2) DJTX (2) Deterministic jitter (Dj) RJTX (2) (4) Random jitter (Rj) (1) (2) (3) (4) Device setting: OS1 = L, DE1 = –6 dB, EQ1 = 7 dB Deterministic jitter (Dj) Device setting: OS2 = H, DE2 = –6 dB, EQ2 = 7dB UI (3)p-p UI (3)p-p Includes RJ at 10-12 BER Determininstic jitter measured with K28.5 pattern, Random jitter measured with K28.5 pattern at the ends of reference channel in Figure 6, VID=1000mVpp, 5Gbps, –3.5dB DE from source UI = 200ps Rj calculated as 14.069 times the RMS random jitter for 10-12 BER IN Tdiff_HL Tdiff_LH OUT Figure 3. Propagation Delay IN+ VEID_TH Vcm INtidleEntry tidleExit OUT + Vcm OUT - Figure 4. Electrical Idle Mode Exit and Entry Delay 80% 20% tr tf Figure 5. Ouput Rise and Fall Times 6 Submit Documentation Feedback Copyright © 2011–2012, Texas Instruments Incorporated Product Folder Link(s): SN65LVPE502CP SN65LVPE502CP SLLSE79B – MARCH 2011 – REVISED FEBRUARY 2012 www.ti.com Jitter Measurement CH1 SN65LVPE502CP A 1 2 AWG* CH1 Up to 3 m (30 AWG) 20" 4" 1"-6" B AWG* CH2 Jitter Measurement CH2 Figure 6. Jitter Measurement Setup 1-bit 1 to N bits tDE DEx = 0dB 1-bit 1 to N bits -3.5dB -6dB Vcm VTXDIFF_NTB_P-P VTXDIFF_TB_P-P tDE Figure 7. Output De-Emphasis Levels OSx = NC Submit Documentation Feedback Copyright © 2011–2012, Texas Instruments Incorporated Product Folder Link(s): SN65LVPE502CP 7 SN65LVPE502CP SLLSE79B – MARCH 2011 – REVISED FEBRUARY 2012 www.ti.com DEVICE INFORMATION VCC EQ1 DE1 OS1 EN_RXD GND 1 6 NC SN65LVPE502CP 24 7 NC TX1- RX1CH1 RX1+ TX1+ Thermal Pad (must be soldered to GND plane) GND GND RX2- TX2CH2 12 TX2+ RX2+ 19 13 18 GND EQ2 DE2 OS2 RSVD VCC Bottom View GND EN_RXD OS1 DE1 EQ1 VCC 6 NC 1 SN65LVPE502CP 7 24 NC TX1- RX1CH1 RX1+ TX1+ Thermal Pad (must be soldered to GND plane) GND TX2- GND RX2- CH2 CH2 CH2 TX2+ 12 19 RX2+ 18 13 VCC RSVD OS2 DE2 EQ2 GND Top View Figure 8. Flow-Through Pin-Out Table 1. Pin Functions PIN Number Name I/O Type Description HIGH SPEED DIFFERENTIAL I/O PINS 8 8 RX1– I, CML 9 RX1+ I, CML 20 RX2– I, CML 19 RX2+ I, CML Non-inverting and inverting CML differential input for CH 1 and CH 2. These pins are tied to an internal voltage bias by dual termination resistor circuit. Submit Documentation Feedback Copyright © 2011–2012, Texas Instruments Incorporated Product Folder Link(s): SN65LVPE502CP SN65LVPE502CP SLLSE79B – MARCH 2011 – REVISED FEBRUARY 2012 www.ti.com Table 1. Pin Functions (continued) PIN I/O Type Number Name 23 TX1– O, VML 22 TX1+ O, VML 11 TX2– O, VML 12 TX2+ O, VML Description Non-inverting and inverting VML differential output for CH 1 and CH 2. These pins are internally tied to voltage bias by termination resistors. DEVICE CONTROL PIN 5 EN_RXD 14 7, 24 I, LVCMOS Sets device operation modes per Table 2. Internally pulled to VCC RSVD I, LVCMOS RSVD, internally pulled to GND. Can be left as No-connect. NC No-connect Pads are not internally connected EQ CONTROL PINS (1) 3, 16 DE1, DE2 I, LVCMOS Selects de-emphasis settings for CH 1 and CH 2 per Table 2. Internally tied to Vcc/2 2, 17 EQ1, EQ2 I, LVCMOS Selects equalization settings for CH 1 and CH 2 per Table 2. Internally tied to Vcc/2 4, 15 OS1, OS2 I, LVCMOS Selects output amplitude for CH 1 and CH 2 per Table 2. Internally tied to Vcc/2 POWER PINS VCC Power Positive supply should be 3.3V ± 10% 6, 10, 18, 21 GND Power Supply ground 1,13 (1) Internally biased to Vcc/2 with >200kΩ pull-up/pull-down. When pins are left as NC board leakage at this pin pad must be < 1 µA otherwise drive to Vcc/2 to assert mid-level state Table 2. Signal Control Pin Setting OUTPUT SWING AND EQ CONTROL (at 2.5 GHz) OSx (1) TRANSISTION BIT AMPLITUDE (TYP mVpp) EQx (1) EQUALIZATION (dB) NC (default) 1042 NC (default) 0 0 908 0 7 1127 1 15 1 OUTPUT DE CONTROL (at 2.5 GHz) DEx (1) OSx (1) = NC OSx (1) = 0 OSx (1) = 1 NC (default) 0 dB 0 dB 0 dB 0 –3.5 dB –2.2 dB –4.4 dB 1 –6.0 dB –5.2 dB –6.0 dB CONTROL PINS SETTINGS (1) EN_RXD DEVICE FUNCTION 1 (default) Normal Operation 0 Sleep Mode Where x = Channel 1 or Channel 2 USB Host USB Device SN65LVPE502CP Device PCB 8"-20" 2"-6" Up to 3 m (30 AWG ) 1 "-6 " NOTE: For more detailed placement example of redriver see typical eye diagrams and jitter plots at end of data sheet. Figure 9. Redriver Placement Example Submit Documentation Feedback Copyright © 2011–2012, Texas Instruments Incorporated Product Folder Link(s): SN65LVPE502CP 9 SN65LVPE502CP SLLSE79B – MARCH 2011 – REVISED FEBRUARY 2012 www.ti.com DETAILED DESCRIPTION Programmable EQ, De-Emphasis and Amplitude Swing The SN65LVPE502CP is designed to minimize signal degradation effects such as crosstalk and inter-symbol interference (ISI) that limits the interconnect distance between two devices. The input stage of each channel offers selectable equalization settings that can be programmed to match loss in the channel. The differential outputs provide selectable de-emphasis to compensate for the anticipated distortion USB 3.0 signal will experience. Level of de-emphasis will depend on the length of interconnect and its characteristics. The SN65LVPE502CP provides a unique way to tailor output de-emphasis on a per channel basis with use of DE and OS pins. All Rx and Tx equalization settings supported by the device are programmed by six 3-state pins as shown in Table 2. Low Power Modes Device supports three low power modes as described below 1. Sleep Mode Initiated anytime EN_RXD undergoes a high to low transition and stays low or when device powers up with EN_RXD set low. In sleep mode both input and output terminations are held at HiZ and device ceases operation to conserve power. Sleep mode max power consumption is 1mW, entry time is 2µs, device exits sleep mode to Rx.Detect mode after EN_RXD is driven to Vcc, exit time is 100µs max. 2. RX Detect Mode--When no remote device is connected Anytime LVPE502CP detects a break in link (i.e. when upstream device is disconnected) or after power-up fails to find a remote device, LVPE502CP goes to Rx Detect mode and conserves power by shutting down majority of its internal circuitry. In this mode input termination for both channels are driven to Hi-Z. In Rx Detect mode device power is <10mW (TYP) or less than 5% of its normal operating power . This feature is very useful in saving system power in mobile applications like notebook PC where battery life is critical. Anytime an upstream device gets reconnected the redriver automatically senses the connection and goes to normal operating mode. This operation requires no setting to the device. 3. U2/U3 Mode With the help of internal timers the device tracks when link enters USB 3.0 low power modes U2 and U3; in these modes link is in electrical idle state. LVPE502CP will selectively turn-off internal circuitry to save on power. Typical power saving is about 75% lower than normal operating mode. The device will automatically revert to active mode when signal activity (LFPS) is detected. Receiver Detection At Power Up or Reset After power-up or anytime EN_RXD is toggled, RX.Detect cycle is performed by first setting Rx termination for each channel to Hi-Z, device then starts sensing for receiver termination that may be attached at the other end of each TX. If receiver is detected on both channel • The TX and RX terminations are switched to ZDIFF_TX, ZDIFF_RX respectively. If • • • no receiver is detected on one or both channels The transmitter is pulled to Hi-Z The channel is put in low power mode Device attempts to detect Rx termination in 12 ms (TYP) interval until termination is found or device is put in sleep mode During U2/U3 Link State Rx detection is also performed periodically when link is in U2/U3 states. However in these states during Rx detection, input termination is not automatically disabled before performing Rx.Detect. If termination is found device goes back to its low power state if termination is not found then device disables its input termination and then jumps to power-up RX.Detect state. 10 Submit Documentation Feedback Copyright © 2011–2012, Texas Instruments Incorporated Product Folder Link(s): SN65LVPE502CP SN65LVPE502CP SLLSE79B – MARCH 2011 – REVISED FEBRUARY 2012 www.ti.com Electrical Idle Support Electrical idle support is needed for low frequency periodic signaling (LFPS) used in USB 3.0 side band communication. A link is in an electrical idle state when the TX± voltage is held at a steady constant value like the common mode voltage. LVPE502CP detects an electrical idle state when RX± voltage at the device pin falls below VRX_LFPS_DIFFp-p min. After detection of an idle state in a given channel the device asserts electrical idle state in its corresponding TX. When RX± voltage exceeds VRX_LFPS_DIFFp-p max normal operation is restored and output start passing input signal. Electrical idle exit and entry time is speccified at < 6ns. TYPICAL EYE DIAGRAM AND PERFORMANCE CURVES Measurement equipment details: • Generator (source) LeCroy PERT3, • Signal: 5Gbps, 1000mVp-p, 3.5 dB De-Emphasis • Tj and Dj measurements based on CP0 (USB 3 compliance pattern) which is D0.0 or logical idle with SKP sequences removed • Rj measurements based on CP1 or D10.2 symbol containing alternating 0s and 1s at Nyquist frequency • Oscilloscope (Sink) LeCroy 25GHz Real Time Oscilloscope • LeCroy QualiPHY software used to measure jitter and collect compliance eye diagrams Device Operating Conditions: VCC = 3.3 V, Temp = 25°C, EQx/DEx/OSx set to their default value when not mentioned Submit Documentation Feedback Copyright © 2011–2012, Texas Instruments Incorporated Product Folder Link(s): SN65LVPE502CP 11 SN65LVPE502CP SLLSE79B – MARCH 2011 – REVISED FEBRUARY 2012 www.ti.com PLOT #1 FIXED OUTPUT TRACE +3m USB 3 CABLE WITH VARIABLE INPUT TRACE LVPE 502CP Input Output = 4" 4mil 4 mil 3m LeCroy 25 GHz Realtime Scope USB 3.0 Source EQ Output Deterministic Jitter - ps - (pk-pk) 140 Output Deterministic Jitter (Post Compliance Cable Channel and CTLE) versus Input Trace Length ( output trace fixed at 4") 120 100 Dj Max Limit per USB 3.0 Spec 80 EQ = 0 dB EQ = 7 dB 60 40 EQ = 15 dB 20 0 0 12 DE = 0dB 5 10 15 20 25 30 35 Input Trace Length (inches) Submit Documentation Feedback 40 45 50 Copyright © 2011–2012, Texas Instruments Incorporated Product Folder Link(s): SN65LVPE502CP SN65LVPE502CP SLLSE79B – MARCH 2011 – REVISED FEBRUARY 2012 www.ti.com PLOT #2 FIXED INPUT TRACE WITH VARIABLE OUTPUT TRACE and +3m USB 3.0 CABLE LVPE502CP Input = 12" Output 4mil 4 mil 3m LeCroy 25 GHz Realtime Scope USB 3.0 Source EQ = 7dB DE = 0dB Output Deterministic Jitter (Post Compliance Cable Channel and CTLE) versus Output Trace Length--Measured with Device DE Fixed @0dB 90 Dj Max Limit per USB 3.0 Spec Output Deterministic Jitter - ps - (pk-pk) 80 70 60 50 Input Trace = 12 inches 40 30 20 10 0 0 2 4 6 8 10 12 14 16 18 20 Output Trace Length (inches) Submit Documentation Feedback Copyright © 2011–2012, Texas Instruments Incorporated Product Folder Link(s): SN65LVPE502CP 13 SN65LVPE502CP SLLSE79B – MARCH 2011 – REVISED FEBRUARY 2012 www.ti.com PLOT #3 FIXED INPUT TRACE WITH VARIABLE OUTPUT TRACE and (No Cable) LVPE 502CP Input = 12" Output 4mil 4 mil LeCroy 25 GHz Realtime Scope USB 3.0 Source EQ = 7dB DE Output Deterministic Jitter (Post CTLE) versus Output Trace Length Input Trace Fixed at 12" 90 Output Deterministic Jitter - ps - (pk-pk) 80 Dj Max Limit per USB 3.0 Spec 70 DE = 0 dB 60 DE = -3.5 dB 50 DE = -6 dB 40 30 20 10 0 14 0 5 10 15 20 25 30 35 Input Trace Length (inches) Submit Documentation Feedback 40 45 50 Copyright © 2011–2012, Texas Instruments Incorporated Product Folder Link(s): SN65LVPE502CP SN65LVPE502CP SLLSE79B – MARCH 2011 – REVISED FEBRUARY 2012 www.ti.com USB 3.0 MASK EYE DIAGRAM TEST CASE I FIXED OUTPUT AND VARIABLE INPUT TRACE DE= 0dB, EQ = 0dB, Input = 4" , Output = 4" + 3m Cable DE= 0dB, EQ = 0dB, Input = 8” , Output = 4” + 3m Cable Submit Documentation Feedback Copyright © 2011–2012, Texas Instruments Incorporated Product Folder Link(s): SN65LVPE502CP 15 SN65LVPE502CP SLLSE79B – MARCH 2011 – REVISED FEBRUARY 2012 www.ti.com DE= 0dB, EQ = 0dB, Input = 12” , Output = 4” + 3m Cable DE= 0dB, EQ = 0dB, Input = 16” , Output = 4” + 3m Cable DE= 0dB, EQ = 0dB, Input = 20” , Output = 4” + 3m Cable 16 Submit Documentation Feedback Copyright © 2011–2012, Texas Instruments Incorporated Product Folder Link(s): SN65LVPE502CP SN65LVPE502CP SLLSE79B – MARCH 2011 – REVISED FEBRUARY 2012 www.ti.com DE= 0dB, EQ = 7dB, Input = 24” , Output = 4” + 3m Cable DE= 0dB, EQ = 7dB, Input = 32” , Output = 4” + 3m Cable DE= 0dB, EQ = 7dB, Input = 36” , Output = 4” + 3m Cable Submit Documentation Feedback Copyright © 2011–2012, Texas Instruments Incorporated Product Folder Link(s): SN65LVPE502CP 17 SN65LVPE502CP SLLSE79B – MARCH 2011 – REVISED FEBRUARY 2012 www.ti.com DE= 0dB, EQ = 15dB, Input = 36” , Output = 4” + 3m Cable DE= 0dB, EQ = 15dB, Input = 48” , Output = 4” + 3m Cable CASE II FIXED INPUT AND VARIABLE OUTPUT TRACE+ 3m CABLE DE= 0dB, EQ = 7dB, Input = 12” , Output = 4” + 3m Cable 18 Submit Documentation Feedback Copyright © 2011–2012, Texas Instruments Incorporated Product Folder Link(s): SN65LVPE502CP SN65LVPE502CP SLLSE79B – MARCH 2011 – REVISED FEBRUARY 2012 www.ti.com DE= 0dB, EQ = 7dB, Input = 12” , Output = 8” + 3m Cable DE= 0dB, EQ = 7dB, Input = 12” , Output = 12” + 3m Cable DE= 0dB, EQ = 7dB, Input = 12” , Output = 16” + 3m Cable Submit Documentation Feedback Copyright © 2011–2012, Texas Instruments Incorporated Product Folder Link(s): SN65LVPE502CP 19 SN65LVPE502CP SLLSE79B – MARCH 2011 – REVISED FEBRUARY 2012 www.ti.com DE= 0dB, EQ = 7dB, Input = 12” , Output = 20” + 3m Cable CASE III FIXED INPUT AND VARIABLE OUTPUT TRACE (No Cable) DE= 0dB, EQ = 7dB, Input = 12” , Output = 8” DE= 0dB, EQ = 7dB, Input = 12” , Output = 32” 20 Submit Documentation Feedback Copyright © 2011–2012, Texas Instruments Incorporated Product Folder Link(s): SN65LVPE502CP SN65LVPE502CP SLLSE79B – MARCH 2011 – REVISED FEBRUARY 2012 www.ti.com DE= 0dB, EQ = 7dB, Input = 12” , Output = 36” DE= -3.5dB, EQ = 7dB, Input = 12” , Output = 36” DE= -6.0dB, EQ = 7dB, Input = 12” , Output = 40” DE= -6.0dB, EQ = 7dB, Input = 12” , Output = 44” Submit Documentation Feedback Copyright © 2011–2012, Texas Instruments Incorporated Product Folder Link(s): SN65LVPE502CP 21 SN65LVPE502CP SLLSE79B – MARCH 2011 – REVISED FEBRUARY 2012 www.ti.com REVISION HISTORY Changes from Original (March 2011) to Revision A Page • Changed the Block Diagram label From: CM/EN_RXD To: EN_RXD ................................................................................. 2 • Changed From: CM To: RSVD in the THERMAL CHARACTERISTICS table Test Conditions ........................................... 3 • Changed From: CM To: RSVD in the RECOMMENDED OPERATING CONDITIONS table Test Conditions .................... 4 • Changed pin name From: CM To: RSVD in the Flow-Through Pin-Out illustration ............................................................. 8 • Changed pin name and description From: CM To: RSVD in the Pin Functions table .......................................................... 9 • Deleted CM and Device Functions columns from the Control Pins Settings of Table 2 ...................................................... 9 • Deleted the USB Compliance Mode section ...................................................................................................................... 11 Changes from Revision A (September 2011) to Revision B Page • Changed the I/O type for the TX pins (11, 12, 22, 23) From: O, CML To: O, VML .............................................................. 9 • Changed the pin Description for the TX pins (11, 12, 22, 23) From: Non-inverting and inverting CML differential output for CH 1 and CH 2 To: Non-inverting and inverting VML differential output for CH 1 and CH 2 .............................. 9 22 Submit Documentation Feedback Copyright © 2011–2012, Texas Instruments Incorporated Product Folder Link(s): SN65LVPE502CP PACKAGE OPTION ADDENDUM www.ti.com 31-Mar-2012 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) SN65LVPE502CP1RGER ACTIVE VQFN RGE 24 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR SN65LVPE502CPRGER ACTIVE VQFN RGE 24 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR SN65LVPE502CPRGET ACTIVE VQFN RGE 24 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Samples (Requires Login) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 31-Mar-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant SN65LVPE502CP1RGER VQFN RGE 24 3000 330.0 12.4 4.25 4.25 1.15 8.0 12.0 Q1 SN65LVPE502CPRGET VQFN RGE 24 250 180.0 12.4 4.25 4.25 1.15 8.0 12.0 Q2 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 31-Mar-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) SN65LVPE502CP1RGER VQFN RGE 24 3000 346.0 346.0 29.0 SN65LVPE502CPRGET VQFN RGE 24 250 210.0 185.0 35.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2012, Texas Instruments Incorporated