SF1056A ® • • • • • • Designed for DECT and WLAN IF Applications Low Insertion Loss Excellent Size-to-Performance Ratio Hermetic 13.3 X 6.5 mm Surface-Mount Case Unbalanced Input and Output Complies with Directive 2002/95/EC (RoHS) 110.592 MHz SAW Filter Pb Absolute Maximum Ratings Rating Value Units Maximum Incident Power in Passband +10 dBm Max. DC voltage between any 2 terminals 30 VDC Storage Temperature Range -40 to +85 Suitable for lead-free soldering - Max Soldering Profile °C SM13365-12 260°C for 30 s Electrical Characteristics Characteristic Nominal Center Frequency Passband Sym fC Insertion Loss at fc Rejection IL 3 dB Passband BW3 Group Delay Variation over fc ±576 kHz GDV Notes Typ 110.592 Max 8.5 10.0 ±576 ±750 1 1, 2 fc-3.4 to fc-1.728 and fc+1.728 to fc+3.4 MHz 1, 2, 3 DC to fc-3.4 and fc+3.4 to 200 MHz Min <150 28 40 40 >45 Ultimate dB kHz 200 nsP-P dB 45 TA Operating Temperature Range Units MHz 1 Impedance Matching to 50 Ω unbalanced +60 -10 °C External L-C Case Style SM13365-12 13.3 X 6.5 mm Nominal Footprint Lid Symbolization (YY=year, WW=week) See note 4 RFM SF1056A YYWW Electrical Connections Connection Terminals Port 1Hot 2 Port 1 Gnd Return 3 Port 2 Hot 8 Port 2 Gnd Return Case Ground 9 All Others Notes: 1. 2. 3. 4. 5. Unless noted otherwise, all specifications apply over the operating temperature range with filter soldered to the specified demonstration board with impedance matching to 50 Ω and measured with 50 Ω network analyzer. Unless noted otherwise, all frequency specifications are referenced to the nominal center frequency, fc. Rejection is measured as attenuation below the minimum IL point in the passband. Rejection in final user application is dependent on PCB layout and external impedance matching design. See Application Note No. 42 for details. "LRIP" or "L" after the part number indicates "low rate initial production" and "ENG" or "E" indicates "engineering prototypes." The design, manufacturing process, and specifications of this filter are subject to change. 6. 7. 8. 9. 10. RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 ©1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. Either Port 1 or Port 2 may be used for either input or output in the design. However, impedances and impedance matching may vary between Port 1 and Port 2, so that the filter must always be installed in one direction per the circuit design. US and international patents may apply. RFM, stylized RFM logo, and RF Monolithics, Inc. are registered trademarks of RF Monolithics, Inc. ©Copyright 1999, RF Monolithics Inc. Electrostatic Sensitive Device. Observe precautions for handling. E-mail: [email protected] http://www.rfm.com SF1056A 112904 110.592 MHz SAW Filter RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 ©1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. E-mail: [email protected] http://www.rfm.com SF1056A 112904 110.592 MHz SAW Filter Quantity Per Reel 254 "B" REF. 100 REF. Tape and Reel Specifications 100 Min 1000 Max See Detail "A" 13. 0 12.0 24.4 20 21.0 .2 2.0 COMPONENT ORIENTATION and DIMENSIONS Carrier Tape Dimensions Ao 7.0 mm Bo 13.8 mm Ko 2.0 mm Pitch 12.0 mm W 24.0 mm PIN #1 USER DIRECTION OF FEED RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 ©1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. E-mail: [email protected] http://www.rfm.com SF1056A 112904 110.592 MHz SAW Filter SM13365-12 Case 12-Terminal Ceramic Surface-Mount Case 13.3 x 6.5 mm Nominal Footprint Case Dimensions Dimension A B C D E H P Min 13.08 6.27 Materials Max 13.60 6.80 2.00 Inches Nom 0.524 0.256 0.075 0.059 0.031 0.039 0.100 Min 0.515 0.247 Max 0.535 0.268 0.079 Electrical Connections Solder Pad Termination Au plating 30 - 60 µinches (76.2-152 µm) over 80200 µinches (203-508 µm) Ni. Lid Fe-Ni-Co Alloy Electroless Nickel Plate (8-11% Phosphorus) 100-200 µinches Thick Body mm Nom 13.31 6.50 1.91 1.50 0.79 1.0 2.54 Connection Port 1 Port 2 Al2O3 Ceramic Terminals Input or Return 2 Return or Input 3 Output or Return 8 Return or Output Pb Free 9 Ground All others Single Ended Operation Return is ground Differential Operation B 3 Return is hot C 4 D H 2 1 2 3 4 1 P (8 Places) 5 12 12 5 6 11 11 6 7 10 10 7 A 8 9 TOP VIEW RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 ©1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. 9 E (10 Places) 8 BOTTOM VIEW E-mail: [email protected] http://www.rfm.com SF1056A 112904 BILL OF MATERIALS PART IDENTIFIER DESCRIPTION 1 DESCRIPTION 2 SF1056A-DEMO SF1056A-000 400-0735-001 500-0003-750 500-0003-560 500-0010-470 500-0010-680 500-0248-001 DEMO BOARD, SF1056A ASSY DIGRAM, DEMO BOARD PCB, DEMO BOARD, 13.3 X 6.5 CAP ,CHIP, NPO, 75 (J), STD CAP, CHIP, NPO, 56 (J), STD IND, CHIP, 1008CS, 47 NH, 10% IND, CHIP, 1008CS, 68 NH, 10% CONN,COAX,FLANGE MT.JACK SF1056A 0 1.0000 1.0000 1.0000 1.0000 1.0000 2.0000 4 HOLE SIZE FSCM NO. A SCALE QTY/ASSY NONE W/O or ECN REFERENCE DESCRIPTION PCB1 C1 C2 L1 L2 J 1,2 DWG NO. SF1056A-DEMO 2U874 7202 REV A SHEET 1 OF 2 REV HISTORY REV ECN DATE A 7202 12/07/98 DESCRIPTION INITIAL RELEASE SIZE FSCM NO. A SCALE NONE W/O or ECN DWG NO. SF1056A-DEMO 2U874 7202 REV A SHEET 2 OF 2