Preliminary SF1183B • • • • RF Filter for Mobile Communication Applications Low Insertion Loss 3.0 x 3.0 x 1.3 mm Surface-Mount Case No Matching Circuit Required 881.5 MHz SAW Filter Absolute Maximum Ratings Rating Value Maximum Incident Power in Passband Max. DC voltage between any 2 terminals Storage Temperature Range Units +10 dBm -5 to +5 VDC -40 to +100 °C Max Soldering Profile SM3030-6 265°C for 10 s Electrical Characteristics Characteristic Nominal Operating Frequency Passband Insertion Loss across 869-894 Amplitude Ripple p-p across 869-894 Attenuation 10 -849 MHz 914 -939 MHz 939 -1049 MHz 1049 -2000 MHz VSWR across 869-894 Source impedance Load impedance Operating Temperature Sym fC IL Notes 1 1, 2, 3 ZS ZL TA 1 Single Ended Input / Output, Impedance match Typ 881.5 2.0 1.0 23.0 30.0 25.0 24.5 1.7 50 50 20 20 23.0 20 Max 3.0 2.0 Units MHz dB dB 2.5 -30 +85 Ω Ω °C No matching network required for operation at 50 ohms Case Style SM3030-6 3 x 3 mm Nominal Footprint Lid Symbolization (Y=year, WW=week, S=shift) 449 YWWS 50 Electrical Connections Connection Min pin 2 pin 5 Terminals Input 2 Output 5 Ground All others Notes: 1. Unless noted otherwise, all specifications apply over the operating temperature range with filter soldered to the specified demonstration board with impedance matching to 50 Ω and measured with 50 Ω network analyzer. 2. Unless noted otherwise, all frequency specifications are referenced to the nominal center frequency, fc. 3. Rejection is measured as attenuation below the minimum IL point in the passband. Rejection in final user application is dependent on PCB layout and external impedance matching design. See Application Note No. 42 for details. 4. "LRIP" or "L" after the part number indicates "low rate initial production" and "ENG" or "E" indicates "engineering prototypes." SAW Filter TOP VIEW 50 All Others 5. The design, manufacturing process, and specifications of this filter are subject to change. 6. Either Port 1 or Port 2 may be used for either input or output in the design. However, impedances and impedance matching may vary between Port 1 and Port 2, so that the filter must always be installed in one direction per the circuit design. 7. US and international patents may apply. 8. RFM, stylized RFM logo, and RF Monolithics, Inc. are registered trademarks of RF Monolithics, Inc. 9. ©Copyright 1999, RF Monolithics Inc. 10. Electrostatic Sensitive Device. Observe precautions for handling. RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 ©1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. E-mail: [email protected] http://www.rfm.com SF1183B-081902 532-1183-001 Page 1 of 5 881.5 MHz SAW Filter Frequency Characteristics wideband response: RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 ©1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. E-mail: [email protected] http://www.rfm.com SF1183B-081902 532-1183-001 Page 2 of 5 881.5 MHz SAW Filter Reflections Functions: S11 VSWR S22 VSWR RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 ©1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. E-mail: [email protected] http://www.rfm.com SF1183B-081902 532-1183-001 Page 3 of 5 881.5 MHz SAW Filter Tape and Reel Specifications "B" REF. 100 REF. “B “ Nominal Size Quantity Per Reel Inches millimeters 7 178 500 13 330 2000 See Detail "A" 13. 0 12.0 20 .2 2.0 COMPONENT ORIENTATION 2.0 4.0 A 1.5 1.75 0.3 3.35 B PIN #1 3.35 12.0 5.5 RO.3 (MAX.) B 8.0 A 1.4 R0.5 (TYP.) 1.5 SECTION A-A SECTION B-B RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 ©1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. USER DIRECTION OF FEED E-mail: [email protected] http://www.rfm.com SF1183B-081902 532-1183-001 Page 4 of 5 881.5 MHz SAW Filter SM3030-6 Case 6-Terminal Ceramic Surface-Mount Case 3.0 X 3.0 mm Nominal Footprint Case Dimensions Dimension Min A B C D E F G H I J mm Nom 3.0 3.0 1.3 0.9 2.54 1.6 0.85 1.5 0.6 1.3 Max Min Inches Nom 0.118 0.118 0.051 0.035 0.100 0.063 0.033 0.059 0.024 0.051 Max Electrical Connections Connection Terminals Port 1 Single Ended Input 2 Port 2 Single Ended Output 5 Ground All others Single Ended Operation Only Dot indicates Pin 1 TOP VIEW BOTTOM VIEW B G C 1 6 A 2 5 3 4 E D RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 ©1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. F H 6 1 5 2 4 3 I J E-mail: [email protected] http://www.rfm.com SF1183B-081902 532-1183-001 Page 5 of 5