SF1141B-2 ® • • • • • Designed for SDARS IF Receiver Low Insertion Loss 5.0 X 7.0 mm Surface-Mount Case Differential Input and Output Complies with Directive 2002/95/EC (RoHS) 75.00 MHz SAW Filter Pb Absolute Maximum Ratings Rating Value Units Maximum Incident Power in Passband +10 dBm Max. DC voltage between any 2 terminals 30 VDC Storage Temperature Range -40 to +105 Max Soldering Profile °C 265°C for 10 s SMP-03 Electrical Characteristics Characteristic Nominal Center Frequency Passband Insertion Loss at fc 1dB Passband Fast Amplitude Ripple over fc ±6.35 MHz Group Delay Variation over fc ±6.35 MHz Rejection fc-18.8 to fc-10.95 and FC+18.8 to FC+100 MHz fc+10.95 to fc+18.8 MHz Operating Temperature Range Differential Input and Output Impedance Case Style Lid Symbolization (YY=year, WW=week, S=shift) See note 4 Sym fC IL BW1 Notes Min 1 ±6.35 Typ 75.000 12.5 ±7.43 1, 2 GDV 1, 2, 3 TA 1 6 40 30 -40 75 45 36 Max 16.0 1.5 200 +105 250 ohms SMP-03 7 x 5 mm Nominal Footprint RFM SF1141B-2 YYWWS Units MHz dB MHz dBP-P nsP-P dB °C Electrical Connections Connection Port 1 Hot Port 1 Ground Return Port 2 Hot Port 2 Ground Return Case Ground Terminals 10 1 5 6 All Others Notes: 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. Unless noted otherwise, all specifications apply over the operating temperature range with filter soldered to the specified demonstration board with impedance matching to 50 Ω and measured with 50 Ω network analyzer. Unless noted otherwise, all frequency specifications are referenced to the nominal center frequency, fc. Rejection is measured as attenuation below the minimum IL point in the passband. Rejection in final user application is dependent on PCB layout and external impedance matching design. See Application Note No. 42 for details. "LRIP" or "L" after the part number indicates "low rate initial production" and "ENG" or "E" indicates "engineering prototypes." The design, manufacturing process, and specifications of this filter are subject to change. Tape and Reel Standard ANSI / EIA 481. Either Port 1 or Port 2 may be used for either input or output in the design. However, impedances and impedance matching may vary between Port 1 and Port 2, so that the filter must always be installed in one direction per the circuit design. US and international patents may apply. RFM, stylized RFM logo, and RF Monolithics, Inc. are registered trademarks of RF Monolithics, Inc. ©Copyright 1999, RF Monolithics Inc. Electrostatic Sensitive Device. Observe precautions for handling. RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 ©1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. E-mail: [email protected] http://www.rfm.com SF1141B-2-012606-Ver1.1 Page 1 75.00 MHz SAW Filter Tape and Reel Specifications 100 REF. "B" REF. “B “ Nominal Size Quantity Per Reel Inches millimeters 7 178 500 13 330 2000 See Detail "A" 13. 0 16.0 12.0 20 .2 2.0 COMPONENT ORIENTATION and DIMENSIONS Carrier Tape Dimensions Ao 5.5 mm Bo 7.5 mm Ko 2.0 mm Pitch 8.0 mm W 16.0 mm PIN #1 USER DIRECTION OF FEED RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 ©1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. E-mail: [email protected] http://www.rfm.com SF1141B-2-012606-Ver1.1 Page 2 75.00 MHz SAW Filter 10-Terminal Ceramic Surface-Mount Case 7 x 5 mm Nominal Footprint Case Dimensions Dimension A B C D E H J K P Min 6.80 4.80 mm Nom 7.00 5.00 1.65 0.60 2.54 1.0 5.00 3.00 1.27 Max 7.20 5.20 2.00 Min 0.268 0.189 Inches Nom 0.276 0.197 0.065 0.024 0.100 0.039 0.197 0.118 0.050 Max 0.283 0.205 0.079 Electrical Connections Connection Terminals Port 1 Input or Return 10 Return or Input 1 Port 2 Output or Return 5 Return or Output 6 Ground All others Single Ended Operation Return is ground Differential Operation Return is hot C B 1 10 -2 RFM SF1141B YYWWS 2 3 4 E H 5 10 D 9 8 A 1 9 2 8 3 7 4 P 7 6 TOP VIEW RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 ©1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. 6 5 BOTTOM VIEW E-mail: [email protected] http://www.rfm.com SF1141B-2-012606-Ver1.1 Page 3