SF1134A 170.6 MHz SAW Filter PRELIMINARY • • • • • Designed for EDGE BTS Receiver IF Applications Low Insertion Loss Excellent Size-Performance Ratio Hermetic SMP-75 Surface-Mount Case Unbalanced Input and Output Associated Plots Attached Characteristic Nominal Center Frequency Passband Sym fc IL Min Insertion Loss at fc 0.5 dB Passband 1 dB Passband Amplitude Ripple over fc ±90 kHz Amplitude Ripple over fc ±150 kHz Group Delay Variation over fc ±90 kHz GDV Rejection fc-0.6 to fc-0.4 and fc+0.4 to fc+0.6 MHz fc-0.8 to fc-0.6 and fc+0.6 to fc+0.8 MHz fc-1.6 to fc-0.8 and fc+0.8 to fc+1.6 MHz fc-3.0 to fc-1.6 and fc+1.6 to fc+3.0 MHz fc-5.8 to fc-3.0 and fc+3.0 to fc+5.8 MHz fc-35 to fc-5.8 and fc+5.8 to fc+35 MHz fc-75 to fc-35 and fc+35 to fc+75 MHz DC to fc-75 and fc+75 to fc+1000 MHz Operating Temperature Range Impedance Matching to 50 Ω unbalanced Case Style Lid symbolization (YY = year, WW = week) Absolute Maximum Ratings Rating Maximum Incident Power in Passband Max. DC voltage between any 2 terminals Storage Temperature Range Max Soldering Profile Typ 170.600 Max 9.0 ±90 ±150 13 27 40 43 47 50 45 40 -10 TBD 15 35 45 55 55 55 55 .5 1 400 +85 Units MHz dB kHz Notes 1 1, 2 dBP-P nsP-P dB 1, 2, 3 °C 1 External L-C SMP-75 19 x 6.5 mm Nominal Footprint RFM SF1088A YYWW Value Units +20 dBm 30 VDC -40 to +85 °C 265°C for 10 s Electrical Connections Connection Terminals Port 1 Hot 10 Port 1 Gnd Return 1 Port 2 Hot 5 Port 2 Gnd Return 6 Case Ground All others Notes: 1. Unless noted otherwise, all specifications apply over the operating temperature range with filter soldered to the specified demonstration board with impedance matching to 50 Ω and measured with 50 Ω network analyzer. 2. Unless noted otherwise, all frequency specifications are referenced to the nominal center frequency, fc. 3. Rejection is measured as attenuation below the minimum IL point in the passband. Rejection in final user application is dependent on PCB layout and external impedance matching design. See Application Note No. 42 for details. 4. “LRIP” or “L” after the part number indicates “low rate initial production” and “ENG” or “E” indicates “engineering prototypes.” 5. The design, manufacturing process, and specifications of this filter are subject to change. 6. Either Port 1 or Port 2 may be used for either input or output in the design. However, impedances and impedance matching may vary between Port 1 and Port 2, so that the filter must always be installed in one direction per the circuit design. 7. US and international patents may apply. 8. RFM, stylized RFM logo, and RF Monolithics, Inc. are registered trademarks of RF Monolithics, Inc. 9. Copyright 1999, RF Monolithics Inc. 10. Electrostatic Sensitive Device. Observe precautions for handling. RF Monolithics, Inc. 4347 Sigma Road Dallas, Texas 75244 USA Phone: +1(972)233-2903 Fax: +1(972)387-8148 e-mail: [email protected] Home page: www.rfm.com European Sales Office 44 1963 251383 44 1963 251510 SF1134A.DOC 1/17/2001 D