SEME-LAB IP78M00ALCC4

POSITIVE FIXED
VOLTAGE REGULATOR
IP140ME SERIES
IP140MAE SERIES
IP78M00LCC4 SERIES
IP78M00ALCC4 SERIES
FEATURES
DESCRIPTION
•
•
•
•
•
•
•
•
•
•
The IP140M/MA and IP78M00/A series of voltage
regulators are fixed output voltage regulators intended for
local, on-card voltage regulation. These devices are
available in 5, 12 and 15 volt options and are capable of
delivering in excess of 500mA over temperature.
1% output voltage tolerance.
5, 12 and 15V fixed output voltages available.
0.01%/V line regulation.
0.3%/A load regulation.
Thermal overload protection
Short-circuit current limit protection.
Safe operating area protection
Start-up with negative voltage (± supplies) on output.
Hermetic Surface Mount Package
Screening Options Available
The A-suffix devices are fully specified at 0.5A, provide
0.01%/V line regulation, 0.3%/A load regulation and ±1%
output voltage tolerance at room protection.
ABSOLUTE MAXIMUM RATINGS (TC = 25°C unless otherwise stated)
VIN
IO
PD
TJ
Tstg
DC Input Voltage
Output Current
Power Dissipation
Operating Junction Temperature Range
Storage Temperature Range
35V
Internally Limited
Internally Limited
-55 to +150°C
-65 to +150°C
THERMAL PROPERTIES
Symbols
Parameters
Max.
Units
RθJA
Thermal Resistance, Junction To Ambient
120
°C/W
RθJC
Thermal Resistance, Junction To Case
20
°C/W
Semelab Limited reserves the right to change test conditions, parameter limits and package dimensions without notice.
Information furnished by Semelab is believed to be both accurate and reliable at the time of going to press. However
Semelab assumes no responsibility for any errors or omissions discovered in its use. Semelab encourages customers to
verify that datasheets are current before placing orders.
Semelab Limited
Coventry Road, Lutterworth, Leicestershire, LE17 4JB
Telephone +44 (0) 1455 556565
Fax +44 (0) 1455 552612
Email: [email protected]
Website: http://www.semelab-tt.com
Document Number 2832
Issue 2
Page 1 of 8
POSITIVE FIXED
VOLTAGE REGULATOR
IP140ME/MAE, IP78M00/ALCC4 SERIES
ELECTRICAL CHARACTERISTICS(1) (TC = 25°C unless otherwise stated)
IP78M05LCC4, IP140ME-05
Symbols
Parameters
Test Conditions
IOUT = 100mA
VO
Output Voltage
VIN = 10V
P ≤ PMAX, 5mA ≤ IO ≤ 350mA,
VIN = 7.5V to 20V
∆VO
Line Regulation (2)
IO = 200mA
•
Min.
Typ
Max.
4.8
5
5.2
V
4.75
5.25
7V ≤ VIN ≤ 25V
8V ≤ VIN ≤ 25V
IO = 500mA
8V ≤ VIN ≤ 12V
50
25
●
Load Regulation (2)
VIN = 10V
5mA ≤ IO ≤ 500mA
●
IQ
Quiescent Current
VIN = 10V
IO = 350mA
●
VIN = 10V
5mA ≤ IO ≤ 500mA
●
0.5
8V ≤ VIN ≤ 25V
IO = 200mA
●
0.8
VIN = 10V
10Hz ≤ f ≤ 100KHz
f = 120Hz
IO = 300mA
8V ≤ VIN≤ 18V
IO = 100mA
Quiescent Current Change
VN
Output Noise Voltage (3)
∆VIN
∆VO
Ripple Rejection
VD
Drop Out Voltage
ISC
Short-Circuit Current
VIN = 35V
IPK
Short-Circuit Current
VIN = 10V
Average TC of Vo (3)
IO = 5mA
mV
50
∆VO
∆IQ
Units
50
4
40
6
200
62
●
mA
µV
dB
62
IO = 350mA
0.7
2.5
V
300
600
mA
1.0
1.6
A
0.5
mV/°C
Notes
The ● denotes the specifications which apply over the full operating temperature range.
(1)
All characteristics are measured with a capacitor across the input of 0.22µF and a capacitor across the output of 0.1µF. Although power
dissipation is internally limited, theses specifications are applicable to maximum power dissipation PMAX = 2W, IMAX = 0.5A, TJ = 25°C
(2)
Regulation is measured at constant junction temperature, using pulse testing at a low duty cycle. Changes in output voltage due to heating
effects must be taken into account separately.
(3)
By design, not a production test.
Semelab Limited
Coventry Road, Lutterworth, Leicestershire, LE17 4JB
Telephone +44 (0) 1455 556565
Fax +44 (0) 1455 552612
Email: [email protected]
Website: http://www.semelab-tt.com
Document Number 2832
Issue 2
Page 2 of 8
POSITIVE FIXED
VOLTAGE REGULATOR
IP140ME/MAE, IP78M00/ALCC4 SERIES
ELECTRICAL CHARACTERISTICS(1) (TC = 25°C unless otherwise stated)
IP78M05ALCC4, IP140ME-05A
Symbols
Parameters
Test Conditions
IOUT = 100mA
VO
Output Voltage
VIN = 10V
P ≤ PMAX, 5mA ≤ IO ≤ 350mA,
VIN = 7.5V to 20V
∆VO
Line Regulation (2)
IO = 200mA
Min.
Typ
Max.
4.95
5
5.05
V
●
4.85
7V ≤ VIN ≤ 25V
8V ≤ VIN ≤ 25V
IO = 500mA
8V ≤ VIN ≤ 12V
●
5.15
3
10
3
10
3
10
∆VO
Load Regulation (2)
VIN = 10V
5mA ≤ IO ≤ 500mA
●
5
50
IQ
Quiescent Current
VIN = 10V
IO = 350mA
●
4
6
VIN = 10V
5mA ≤ IO ≤ 500mA
●
0.1
0.5
8V ≤ VIN ≤ 25V
IO = 200mA
●
0.2
0.8
VIN = 10V
10Hz ≤ f ≤ 100KHz
40
200
f = 120Hz
IO = 300mA
8V ≤ VIN≤ 18V
IO = 100mA
∆IQ
Quiescent Current Change
VN
Output Noise Voltage (3)
∆VIN
∆VO
Ripple Rejection
VD
Drop Out Voltage
ISC
IPK
Units
●
65
80
65
80
mV
mA
µV
dB
IO = 350mA
2
2.5
V
Short-Circuit Current
VIN = 35V
300
600
mA
Short-Circuit Current
VIN = 10V
1.0
1.4
A
Average TC of Vo (3)
IO = 5mA
0.5
2
mV/°C
0.7
Notes
The ● denotes the specifications which apply over the full operating temperature range.
(1)
All characteristics are measured with a capacitor across the input of 0.22µF and a capacitor across the output of 0.1µF. Although power
dissipation is internally limited, theses specifications are applicable to maximum power dissipation PMAX = 2W, IMAX = 0.5A, TJ = 25°C
(2)
Regulation is measured at constant junction temperature, using pulse testing at a low duty cycle. Changes in output voltage due to heating
effects must be taken into account separately.
(3)
By design, not a production test.
Semelab Limited
Coventry Road, Lutterworth, Leicestershire, LE17 4JB
Telephone +44 (0) 1455 556565
Fax +44 (0) 1455 552612
Email: [email protected]
Website: http://www.semelab-tt.com
Document Number 2832
Issue 2
Page 3 of 8
POSITIVE FIXED
VOLTAGE REGULATOR
IP140ME/MAE, IP78M00/ALCC4 SERIES
ELECTRICAL CHARACTERISTICS(1) (TC = 25°C unless otherwise stated)
IP78M12LCC4, IP140ME-12
Symbols
Parameters
Test Conditions
IOUT = 100mA
VO
Output Voltage
VIN = 19V
P ≤ PMAX, 5mA ≤ IO ≤ 350mA,
VIN = 14.8V to 27V
∆VO
Line Regulation (2)
IO = 200mA
Min.
Typ
Max.
11.5
12
12.5
V
●
11.4
12.6
14.5V ≤ VIN ≤ 30V
16V ≤ VIN ≤ 30V
IO = 500mA
16V ≤ VIN ≤ 22V
60
30
●
Load Regulation (2)
VIN = 19V
5mA ≤ IO ≤ 500mA
●
IQ
Quiescent Current
VIN = 19V
IO = 350mA
●
VIN = 19V
5mA ≤ IO ≤ 500mA
●
0.5
14.8V ≤ VIN ≤ 30V
IO = 200mA
●
0.8
VIN = 19V
10Hz ≤ f ≤ 100KHz
f = 120Hz
IO = 300mA
15V ≤ VIN≤ 25V
IO = 100mA
Quiescent Current Change
VN
Output Noise Voltage (3)
∆VIN
∆VO
Ripple Rejection
VD
Drop Out Voltage
ISC
Short-Circuit Current
VIN = 35V
IPK
Short-Circuit Current
VIN = 19V
Average TC of Vo (3)
IO = 5mA
mV
120
∆VO
∆IQ
Units
120
4
75
6
480
55
●
mA
µV
dB
55
IO = 350mA
0.7
2.5
V
300
600
mA
1.0
1.6
A
1.2
mV/°C
Notes
The ● denotes the specifications which apply over the full operating temperature range.
(1)
All characteristics are measured with a capacitor across the input of 0.22µF and a capacitor across the output of 0.1µF. Although power
dissipation is internally limited, theses specifications are applicable to maximum power dissipation PMAX = 2W, IMAX = 0.5A, TJ = 25°C
(2)
Regulation is measured at constant junction temperature, using pulse testing at a low duty cycle. Changes in output voltage due to heating
effects must be taken into account separately.
(3)
By design, not a production test.
Semelab Limited
Coventry Road, Lutterworth, Leicestershire, LE17 4JB
Telephone +44 (0) 1455 556565
Fax +44 (0) 1455 552612
Email: [email protected]
Website: http://www.semelab-tt.com
Document Number 2832
Issue 2
Page 4 of 8
POSITIVE FIXED
VOLTAGE REGULATOR
IP140ME/MAE, IP78M00/ALCC4 SERIES
ELECTRICAL CHARACTERISTICS(1) (TC = 25°C unless otherwise stated)
IP78M12ALCC4, IP140MAE-12
Symbols
Parameters
Test Conditions
IOUT = 100mA
VO
Output Voltage
VIN = 19V
P ≤ PMAX, 5mA ≤ IO ≤ 350mA,
VIN = 14.8V to 27V
∆VO
Line Regulation (2)
IO = 200mA
Min.
Typ
Max.
11.88
12
12.12
V
●
11.64
14.5V ≤ VIN ≤ 30V
16V ≤ VIN ≤ 30V
IO = 500mA
16V ≤ VIN ≤ 22V
●
12.36
4
18
4
18
4
18
∆VO
Load Regulation (2)
VIN = 19V
5mA ≤ IO ≤ 500mA
●
10
60
IQ
Quiescent Current
VIN = 19V
IO = 350mA
●
4
6
VIN = 19V
5mA ≤ IO ≤ 500mA
●
0.1
0.5
14.8V ≤ VIN ≤ 30V
IO = 200mA
●
0.2
0.8
VIN = 19V
10Hz ≤ f ≤ 100KHz
75
480
f = 120Hz
IO = 300mA
15V ≤ VIN≤ 25V
IO = 100mA
∆IQ
Quiescent Current Change
VN
Output Noise Voltage (3)
∆VIN
∆VO
Ripple Rejection
VD
Drop Out Voltage
ISC
IPK
Units
●
58
72
58
72
mV
mA
µV
dB
IO = 350mA
2
2.5
V
Short-Circuit Current
VIN = 35V
300
600
mA
Short-Circuit Current
VIN = 19V
1.0
1.4
A
Average TC of Vo (3)
IO = 5mA
1.2
4.8
mV/°C
0.7
Notes
The ● denotes the specifications which apply over the full operating temperature range.
(1)
All characteristics are measured with a capacitor across the input of 0.22µF and a capacitor across the output of 0.1µF. Although power
dissipation is internally limited, theses specifications are applicable to maximum power dissipation PMAX = 2W, IMAX = 0.5A, TJ = 25°C
(2)
Regulation is measured at constant junction temperature, using pulse testing at a low duty cycle. Changes in output voltage due to heating
effects must be taken into account separately.
(3)
By design, not a production test.
Semelab Limited
Coventry Road, Lutterworth, Leicestershire, LE17 4JB
Telephone +44 (0) 1455 556565
Fax +44 (0) 1455 552612
Email: [email protected]
Website: http://www.semelab-tt.com
Document Number 2832
Issue 2
Page 5 of 8
POSITIVE FIXED
VOLTAGE REGULATOR
IP140ME/MAE, IP78M00/ALCC4 SERIES
ELECTRICAL CHARACTERISTICS(1) (TC = 25°C unless otherwise stated)
IP78M15LCC4, IP140ME-15
Symbols
Parameters
Test Conditions
IOUT = 100mA
VO
Output Voltage
VIN = 23V
P ≤ PMAX, 5mA ≤ IO ≤ 350mA,
VIN = 18V to 30V
∆VO
Line Regulation (2)
IO = 200mA
Min.
Typ
Max.
14.4
15
15.6
V
●
14.25
15.75
17.5V ≤ VIN ≤ 30V
20V ≤ VIN ≤ 30V
IO = 500mA
20V ≤ VIN ≤ 26V
60
30
●
Load Regulation (2)
VIN = 23V
5mA ≤ IO ≤ 500mA
●
IQ
Quiescent Current
VIN = 23V
IO = 350mA
●
VIN = 23V
5mA ≤ IO ≤ 500mA
●
0.5
18V ≤ VIN ≤ 30V
IO = 200mA
●
0.8
VIN = 23V
10Hz ≤ f ≤ 100KHz
f = 120Hz
IO = 300mA
18.5V ≤ VIN≤ 28.5V
IO = 100mA
Quiescent Current Change
VN
Output Noise Voltage (3)
∆VIN
∆VO
Ripple Rejection
VD
Drop Out Voltage
ISC
Short-Circuit Current
VIN = 35V
IPK
Short-Circuit Current
VIN = 23V
Average TC of Vo (3)
IO = 5mA
mV
150
∆VO
∆IQ
Units
150
4
90
6
600
54
●
mA
µV
dB
54
IO = 350mA
0.7
2.5
V
300
600
mA
1.0
1.6
A
1.5
mV/°C
Notes
The ● denotes the specifications which apply over the full operating temperature range.
(1)
All characteristics are measured with a capacitor across the input of 0.22µF and a capacitor across the output of 0.1µF. Although power
dissipation is internally limited, theses specifications are applicable to maximum power dissipation PMAX = 2W, IMAX = 0.5A, TJ = 25°C
(2)
Regulation is measured at constant junction temperature, using pulse testing at a low duty cycle. Changes in output voltage due to heating
effects must be taken into account separately.
(3)
By design, not a production test.
Semelab Limited
Coventry Road, Lutterworth, Leicestershire, LE17 4JB
Telephone +44 (0) 1455 556565
Fax +44 (0) 1455 552612
Email: [email protected]
Website: http://www.semelab-tt.com
Document Number 2832
Issue 2
Page 6 of 8
POSITIVE FIXED
VOLTAGE REGULATOR
IP140ME/MAE, IP78M00/ALCC4 SERIES
ELECTRICAL CHARACTERISTICS(1) (TC = 25°C unless otherwise stated)
IP78M15ALCC4, IP140MAE-15
Symbols
Parameters
Test Conditions
IOUT = 100mA
VO
Output Voltage
VIN = 23V
P ≤ PMAX, 5mA ≤ IO ≤ 350mA,
VIN = 18V to 30V
∆VO
Line Regulation (2)
IO = 200mA
Min.
Typ
Max.
14.85
15
15.15
V
●
14.55
17.5V ≤ VIN ≤ 30V
20V ≤ VIN ≤ 30V
IO = 500mA
20V ≤ VIN ≤ 26V
●
15.45
4
22
4
22
4
22
∆VO
Load Regulation (2)
VIN = 23V
5mA ≤ IO ≤ 500mA
●
12
75
IQ
Quiescent Current
VIN = 23V
IO = 350mA
●
4
6
VIN = 23V
5mA ≤ IO ≤ 500mA
●
0.1
0.5
18V ≤ VIN ≤ 30V
IO = 200mA
●
0.2
0.8
VIN = 23V
10Hz ≤ f ≤ 100KHz
90
600
f = 120Hz
IO = 300mA
18.5V ≤ VIN≤ 28.5V
IO = 100mA
∆IQ
Quiescent Current Change
VN
Output Noise Voltage (3)
∆VIN
∆VO
Ripple Rejection
VD
Drop Out Voltage
ISC
IPK
Units
●
57
70
57
70
mV
mA
µV
dB
IO = 350mA
2
2.5
V
Short-Circuit Current
VIN = 35V
300
600
mA
Short-Circuit Current
VIN = 23V
1.0
1.4
A
Average TC of Vo (3)
IO = 5mA
1.5
6
mV/°C
0.7
Notes
The ● denotes the specifications which apply over the full operating temperature range.
(1)
All characteristics are measured with a capacitor across the input of 0.22µF and a capacitor across the output of 0.1µF. Although power
dissipation is internally limited, theses specifications are applicable to maximum power dissipation PMAX = 2W, IMAX = 0.5A, TJ = 25°C
(2)
Regulation is measured at constant junction temperature, using pulse testing at a low duty cycle. Changes in output voltage due to heating
effects must be taken into account separately.
(3)
By design, not a production test.
Semelab Limited
Coventry Road, Lutterworth, Leicestershire, LE17 4JB
Telephone +44 (0) 1455 556565
Fax +44 (0) 1455 552612
Email: [email protected]
Website: http://www.semelab-tt.com
Document Number 2832
Issue 2
Page 7 of 8
POSITIVE FIXED
VOLTAGE REGULATOR
IP140ME/MAE, IP78M00/ALCC4 SERIES
APPLICATIONS INFORMATION
Fixed Output Regulator
VIN
VOUT
VOUT
VIN
REG
GND
+
+
0.22uF
Cin
GND
(a)
(b)
Cin required if regulator is located an appropriate distance from power supply filter.
Cout required for stability for given value.
MECHANICAL DATA
Dimensions in mm (inches)
9.14 (0.360)
8.64 (0.340)
1.27 (0.050)
1.07 (0.040)
≈ 2.16 (0.085)
12 13 14 15 16
1.39 (0.055)
1.02 (0.040)
7.62 (0.300)
7.12 (0.280)
11
17
10
18
9
1
8
2
7
6
5
1.39 (0.055)
1.15 (0.045)
4
0.76 (0.030)
0.51 (0.020)
0.33 (0.013)
Rad.
0.08 (0.003)
3
0.43 (0.017)
0.18 (0.007 Rad.
1.65 (0.065)
1.40 (0.055)
LCC4
Underside View
Pads
Pads 4, 5
Pads 6, 7, 8, 9, 10, 11, 12, 13
Pads 1, 2, 15, 16, 17, 18
Pads 3, 14
Connection
VIN
VOUT
GND
No Connection
Semelab Limited
Coventry Road, Lutterworth, Leicestershire, LE17 4JB
Telephone +44 (0) 1455 556565
Fax +44 (0) 1455 552612
Email: [email protected]
Website: http://www.semelab-tt.com
Document Number 2832
Issue 2
Page 8 of 8