规格书编号 SPEC NO : 产品规格书 SPECIFICATION CUSTOMER 客 户： PRODUCT 产 品： SAW FILTER MODEL NO 型 号： HDBF07009A24 PREPARED 编 制： CHECKED 审 核： Houshihong APPROVED 批 准： CHARLES D A T E 日 期： 2007-01-25 客户确认 CUSTOMER RECEIVED: 审核 CHECKED 批准 APPROVED 日期 DATE 无锡市好达电子有限公司 Shoulder Electronics Limited www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 1 of 8 SAW FILTER HDBF07009A24 更改历史记录 History Record 更改日期 Date www.shoulder.cn 规格书编号 Spec No 产品型号 Part No 客户产品型号 Customer No Tel:0755-82916880 Fax:0755-82916881 更改内容描述 Modify Content E-mail:[email protected] 备注 Remark Page 2 of 8 SAW FILTER HDBF07009A24 1. SCOPE This specification shall cover the characteristics of SAW filter with the page system. HDBF07009A24 used for 2. ELECTRICAL SPECIFICATION DC Voltage VDC AC Voltage Vpp Operation temperature Storage temperature RF Power Dissipation 10V 10V50Hz/60Hz -20℃ to +70℃ -40℃ to +85℃ 0dBm Electronic Characteristics Fo = 70.0 MHz Terminating source impedance: 50 ohm and matching network Terminating load impedance: 50 ohm and matching network Minimum Center Frequency MHz Insertion Loss dB 1dB Bandwidth 3dB Bandwidth 40dB Bandwidth Typical Maximum 69.8 70.0 70.2 - 10.8 12.0 MHz MHz MHz 8.2 8.9 - 8.3 9.0 11.5 11.8 Amplitude Ripple (Fo +/- 4.0 MHz) Group Delay Variation (Fo +/- 4.0 MHz) dB nsec - 0.6 70 1.0 120 Absolute Delay usec - 1.47 - Ultimate Rejection dB 40 45 - Temperature Coefficient of Frequency ppm/°C - -86 - www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 3 of 8 SAW FILTER www.shoulder.cn Tel:0755-82916880 HDBF07009A24 Fax:0755-82916881 E-mail:[email protected] Page 4 of 8 SAW FILTER www.shoulder.cn Tel:0755-82916880 HDBF07009A24 Fax:0755-82916881 E-mail:[email protected] Page 5 of 8 SAW FILTER www.shoulder.cn Tel:0755-82916880 HDBF07009A24 Fax:0755-82916881 E-mail:[email protected] Page 6 of 8 SAW FILTER HDBF07009A24 3. TEST CIRCUIT 4.DIMENSION Dimension Pin Configuration 11 Input 5 Output Other Ground www.shoulder.cn Tel:0755-82916880 A B C D E H P Fax:0755-82916881 E-mail:[email protected] min 13.1 6.3 1.21 0.72 mm typ 13.3 6.5 1.36 1.5 0.8 0.76 2.54 max 13.5 6.7 1.51 0.80 Page 7 of 8 SAW FILTER HDBF07009A24 5. ENVIRONMENTAL CHARACTERISTICS 5-1 Temperature cycling Subject the device to a low temperature of -40℃for 30 minutes. Following by a high temperature of +25℃ for 5 Minutes and a higher temperature of +85℃ for 30 Minutes. Then release the device into the room conditions for 1 to 2 hours prior to the measurement. It shall meet the specifications in table 1. 5-2 Resistance to solder heat Submerge the device terminals into the solder bath at 260℃ ±5℃ for 10±1 sec. Then release the device into the room conditions for 4 hours. It shall meet the specifications in table 1. 5-3 Solderability Submerge the device terminals into the solder bath at 245℃ ±5℃ for 5s, More than 95% area of the soldering pad must be covered with new solder. It shall meet the specifications in table 1. 5-4 Mechanical shock Drop the device randomly onto the concrete floor from the height of 1 m 3 times. the filter shall fulfill the specifications in table 1. 5-5 Vibration Subject the device to the vibration for 2 hour each in x,y and z axes with the amplitude of 1.5 mm at 10 to 55 hz. The filter shall fulfill the specifications in table 1. 6. REMARK 6.1 Static voltage Static voltage between signal load & ground may cause deterioration &destruction of the component. Please avoid static voltage. 6.2 Ultrasonic cleaning Ultrasonic vibration may cause deterioration & destruction of the component. Please avoid ultrasonic cleaning 6.3 Soldering Only leads of component may be soldered. Please avoid soldering another part of component. www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 8 of 8