规格书编号 SPEC NO : 产品 规 格书 SPECIFICATION CUSTOMER 客 户： PRODUCT 产 品： SAW FILTER MODEL NO 型 号： HDBF14009C63 SF6-3 PREPARED 编 制： CHECKED 审 核： APPROVED 批 准： D A T E 日 期： 2009-2-26 客户确认 CUSTOMER RECEIVED: 审核 CHECKED 批准 APPROVED 日期 DATE 无锡市好达电子有限公司 Shoulder Electronics Limited www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 1 of 8 SAW FILTER HDBF14009C63 SF6-3 更改历史记录 History Record 更改日期 Date www.shoulder.cn 规格书编号 Spec. No. 产品型号 Part No. 客户产品型号 Customer No. Tel:0755-82916880 Fax:0755-82916881 更改内容描述 Modify Content E-mail:[email protected] 备注 Remark Page 2 of 8 SAW FILTER HDBF14009C63 SF6-3 1. SCOPE This specification shall cover the characteristics of SAW filter BF14009C63 2. ELECTRICAL SPECIFICATION DC Voltage VDC AC Voltage Vpp Operation temperature Storage temperature RF Power Dissipation 10V 10V50Hz/60Hz -40℃ to +85℃ -40℃ to +85℃ 0dBm 2.2Electronic Characteristics Parameter Min Center Frequency 139.92 Insertion Loss -1dB Bandwidth 9.1 -3dB Bandwidth 9.3 -40dB Bandwidth -50dB Bandwidth Phase Linearity(over 1 dB Bandwidth) Group Delay Variation (over 1 dB Bandwidth) Passband Variation Absolute Delay Ultimate Rejection 50 Subatrate Material Ambient Temperature www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 Typ 140 25 9.15 9.39 10.23 10.32 7 65 Max 140.08 26.5 10.3 11.5 3 80 1.0 3.63 51 112LT 25 1.1 3.75 - E-mail:[email protected] Units MHz dB MHz MHz MHz MHz degree nsec dB usec dB ℃ Page 3 of 8 SAW FILTER HDBF14009C63 SF6-3 3. DIMENSION 4.TEST CIRCUIT L1=L2=33nH C1=51pF;C2=47pF 5. ENVIRONMENTAL CHARACTERISTICS 5-1 High temperature exposure Subject the device to +85℃ for 16 hours. Then release the filter into the room conditions www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 4 of 8 SAW FILTER HDBF14009C63 SF6-3 for 24 hours prior to the measurement. It shall fulfill the specifications in 2.2. 5-2 Low temperature exposure Subject the device to -40℃ for 16 hours. Then release the device into the room conditions for 24 hours prior to the measurement. It shall fulfill the specifications in 2.2. 5-3 Temperature cycling Subject the device to a low temperature of -40℃ for 30 minutes. Following by a high temperature of +85℃ for 30 Minutes. Then release the device into the room conditions for 24 hours prior to the measurement. It shall meet the specifications in 2.2. 5-4 Resistance to solder heat Dip the device terminals no closer than 1.5mm into the solder bath at 260℃ ±10℃ for 10±1 sec. Then release the device into the room conditions for 4 hours. The device shall meet the specifications in 2.2. 5-5 Solderability Subject the device terminals into the solder bath at 245℃ ±5℃ for 5s, More than 95% area of the terminals must be covered with new solder. It shall meet the specifications in 2.2. 5-6 Mechanical shock Drop the device randomly onto the concrete floor from the height of 1m 3 times. the device shall fulfill the specifications in 2.2. 5-7 Vibration Subject the device to the vibration for 1 hour each in x,y and z axes with the amplitude of 1.5 mm at 10 to 55 Hz. The device shall fulfill the specifications in 2.2. 6.Typical frequency response www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 5 of 8 SAW FILTER www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 HDBF14009C63 E-mail:[email protected] SF6-3 Page 6 of 8 SAW FILTER www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 HDBF14009C63 E-mail:[email protected] SF6-3 Page 7 of 8 SAW FILTER HDBF14009C63 SF6-3 7. REMARK 7.1 Static voltage Static voltage between signal load & ground may cause deterioration &destruction of the component. Please avoid static voltage. 7.2 Ultrasonic cleaning Ultrasonic vibration may cause deterioration & destruction of the component. Please avoid ultrasonic cleaning 7.3 Soldering Only leads of component may be soldered. Please avoid soldering another part of component. www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 8 of 8