SKYWORKS SKY13322-375LF-EVB

DATA SHEET
SKY13322-375LF: 0.1-6.0 GHz GaAs SP4T Switch
Applications
Description
 Multiband telecommunications up to 6 GHz
The SKY13322-375LF is a GaAs FET I/C single-pole, four-throw
(SP4T) switch. This general purpose switch is an ideal choice for
a variety of multiband telecommunication applications up to
6 GHz.
Features
 Broadband frequency range: 0.1-6.0 GHz
 Low insertion loss: 0.45 dB @ 1 GHz
 Very high isolation: 28 dB @ 1 GHz
 Excellent linearity peformance: P1dB = +30 dBm @ 3.3 V
 Operating voltage range from 1.8 to 5.0 V
 Small, MLPD (10-pin, 2 x 3 mm) package (MSL1, 260 C per
JEDEC J-STD-020)
J2
J4
RFC
J1
J3
The switch is manufactured in a compact, 2 x 3 mm, 10-pin
exposed pad plastic Micro Leadframe Package Dual (MLPD)
package.
A functional block diagram is shown in Figure 1. The pin
configuration and package are shown in Figure 2. Signal pin
assignments and functional pin descriptions are provided in
Table 1.
J2
1
10
J4
V2
2
9
V4
N/C
3
8
RFC
V1
4
7
V3
J1
5
6
J3
S1537
Figure 1. SKY13322-375LF Block Diagram
S1538
Figure 2. SKY13322-375LF Pinout – 10-Pin MLPD
(Top View)
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
201098C • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • August 4, 2010
1
DATA SHEET • SKY13322-375LF SP4T SWITCH
Table 1. SKY13322-375LF Signal Descriptions
Pin #
Name
Description
Pin #
6
Name
J3
Description
1
J2
RF output (Note 1)
RF output (Note 1)
2
V2
DC control voltage
7
V3
DC control voltage
3
N/C
No connection
8
RFC
RF common input (Note 1)
4
V1
DC control voltage
9
V4
DC control voltage
5
J1
RF output (Note 1)
10
J4
RF output (Note 1)
Note 1: A 47 pF blocking capacitor is required for >1 GHz operation. Use larger value capacitors for lower frequency operation.
Table 2. SKY13322-375LF Absolute Maximum Ratings
Parameter
Symbol
Minimum
Typical
Maximum
Units
Input power
PIN
+33
dBm
Voltage range
VCTL
6
V
Storage temperature
TSTG
–65
+150
C
Operating temperature
TOP
–40
+85
C
Note:
Exposure to maximum rating conditions for extended periods may reduce device reliability. There is no damage to device with only one parameter set at the limit and all other
parameters set at or below their nominal value. Exceeding any of the limits listed here may result in permanent damage to the device.
CAUTION: Although this device is designed to be as robust as possible, Electrostatic Discharge (ESD) can damage this device. This device
must be protected at all times from ESD. Static charges may easily produce potentials of several kilovolts on the human body
or equipment, which can discharge without detection. Industry-standard ESD precautions should be used at all times.
Table 3. SKY13322-375LF Recommended Operating Conditions
Parameter
Symbol
Minimum
Frequency
f
0.1
Control voltage:
Low
High
VCTL_L
VCTL_H
0
1.8
Electrical and Mechanical Specifications
The absolute maximum ratings of the SKY13322-375LF are
provided in Table 2. The recommended operating conditions are
specified in Table 3 and electrical specifications are provided in
Table 4.
Typical
3.3
Maximum
Units
6.0
GHz
0.2
5.0
V
V
Typical performance characteristics of the SKY13322-375LF are
illustrated in Figures 3 through 8.
The state of the SKY13322-375LF is determined by the logic
provided in Table 5.
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
2
August 4, 2010 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 201098C
DATA SHEET • SKY13322-375LF SP4T SWITCH
Table 4. SKY13322-375LF Electrical Specifications (Note 1)
(VCTL = 0 V and +3.3 V, TOP = +25 C, PIN = 0 dBm, Characteristic Impedance [ZO] = 50 Ω, Unless Otherwise Noted)
Parameter
Symbol
Test Condition
Min
Typical
Max
Units
0.45
0.60
0.75
1.00
2.00
0.60
0.75
0.95
1.25
dB
dB
dB
dB
dB
Insertion loss
IL
0.1-1.0 GHz
1.0-2.5 GHz
2.5-3.0 GHz
3.0-4.0 GHz
4.0-6.0 GHz
Isolation
Iso
0.1-1.0 GHz
1.0-2.5 GHz
2.5-3.0 GHz
3.0-4.0 GHz
4.0-6.0 GHz
26
23
23
23
28
26
27
27
18
dB
dB
dB
dB
dB
0.1-1.0 GHz
1.0-2.5 GHz
2.5-3.0 GHz
3.0-4.0 GHz
4.0-6.0 GHz
15
15
15
10
22
22
22
13
7.5
dB
dB
dB
dB
dB
60
60
ns
ns
40
mV
VCTL = 0 V/1.8 V,
VCTL = 0 V/2.7 V
VCTL = 0 V/3.3 V
+21.0
+27.5
+30.0
dBm
dBm
dBm
f = 48 MHz,
VCTL = 0 V/2.7 V
+23.5
dBm
VCTL = 0 V/1.8 V,
VCTL = 0 V/2.7 V
VCTL = 0 V/3.3 V
+17.5
+24.5
+27.0
dBm
dBm
dBm
f = 48 MHz,
VCTL = 0 V/2.7 V
+19.5
dBm
+54
+51
dBm
dBm
76
70
dBc
dBc
f = 0.9 GHz
f = 2.45 GHz
70
65
dBc
dBc
VCTL = 1.8 V to 5.0 V
5
μA
Return loss (insertion loss state)
Switching characteristics:
Rise/fall time
On/off time
10/90% or 90/10% RF
50% VCTL to 90/10% RF
Video feedthrough
1 dB Input Compression Point
0.1 dB Input Compression Point
Input IP3
IP1dB
IP0.1dB
IIP3
f = 0.9 GHz/2.45 GHz
f = 0.9 GHz/2.45 GHz
PIN = +15 dBm/tone,
tone spacing = 1 MHz
f = 0.9 GHz,
f = 2.45 GHz
2nd harmonic
2fo
PIN = +17 dBm
f = 0.9 GHz
f = 2.45 GHz
3rd harmonic
Supply current
3fo
ICC
PIN = +17 dBm
Note 1: Performance is guaranteed only under the conditions listed in this Table.
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
201098C • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • August 4, 2010
3
DATA SHEET • SKY13322-375LF SP4T SWITCH
Typical Performance Characteristics
(VCTL = 0 V and +3.3 V, TOP = +25 C, PIN = 0 dBm, Characteristic Impedance [ZO] = 50 Ω, Blocking Capacitors = 47 pF,
Unless Otherwise Noted)
0
0
–10
–0.5
Isolation (dB)
Insertion Loss (dB)
–20
–1.0
RFC to J1
RFC to J2
RFC to J3
RFC to J4
–1.5
–30
–40
RFC to J2
RFC to J3
RFC to J4
–50
–2.0
–60
–70
–2.5
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
0
0.5
1.0
1.5
2.0
Frequency (GHz)
3.5
4.0
4.5
5.0
5.5
6.0
4.5
5.0
5.5
6.0
Figure 4. Isolation vs Frequency
(RFC to J1 Insertion Loss State)
0
0
–10
–10
–20
–20
Isolation (dB)
Isolation (dB)
3.0
Frequency (GHz)
Figure 3. Insertion Loss vs Frequency
–30
–40
RFC to J1
RFC to J3
RFC to J4
–50
2.5
–30
–40
RFC to J1
RFC to J2
RFC to J4
–50
–60
–60
–70
–70
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
0
6.0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
Frequency (GHz)
Frequency (GHz)
Figure 6. Isolation vs Frequency
(RFC to J3 Insertion Loss State)
Figure 5. Isolation vs Frequency
(RFC to J2 Insertion Loss State)
0
0
–5
–10
–10
–15
Return Loss (dB)
Isolation (dB)
–20
–30
–40
–60
–25
RFC to J1
RFC to J2
RFC to J3
RFC to J4
–30
–35
RFC to J1
RFC to J2
RFC to J3
–50
–20
–40
–45
–50
–70
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
Frequency (GHz)
Figure 7. Isolation vs Frequency
(RFC to J4 Insertion Loss State)
5.0
5.5
6.0
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
Frequency (GHz)
Figure 8. RFC Return Loss vs Frequency
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
4
August 4, 2010 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 201098C
5.0
5.5
6.0
DATA SHEET • SKY13322-375LF SP4T SWITCH
Table 5. SKY13322-375LF Truth Table
V1 (Pin 4)
V2 (Pin 2)
1
Note:
V3 (Pin 7)
V4 (Pin 9)
RFC to J1
RFC to J2
0
0
0
Insertion loss
Isolation
0
1
0
0
Isolation
0
0
1
0
Isolation
0
0
0
1
Isolation
RFC to J3
RFC to J4
Isolation
Isolation
Insertion loss
Isolation
Isolation
Isolation
Insertion loss
Isolation
Isolation
Isolation
Insertion loss
“1” = +1.8 V to +5 V. “0” = 0 V to +0.2 V. Any state other than described in this Table places the switch into an undefined state. An undefined state will not damage the device.
Evaluation Board Description
Package and Handling Information
The SKY13322-375LF Evaluation Board is used to test the
performance of the SKY13322-375LF SPDT Switch. An Evaluation
Board schematic diagram is provided in Figure 9. An assembly
drawing for the Evaluation Board is shown in Figure 10.
Since the device package is sensitive to moisture absorption, it is
baked and vacuum packed before shipping. Instructions on the
shipping container label regarding exposure to moisture after the
container seal is broken must be followed. Otherwise, problems
related to moisture absorption may occur when the part is
subjected to high temperature during solder assembly.
Package Dimensions
The PCB layout footprint for the SKY13322-375LF is provided in
Figure 11. Typical case markings are shown in Figure 12.
Package dimensions for the 10-pin MLPD are shown in Figure 13,
and tape and reel dimensions are provided in Figure 14.
CBL
THE SKY13322-375LF is rated to Moisture Sensitivity Level 1
(MSL1) at 260 C. It can be used for lead or lead-free soldering.
Care must be taken when attaching this product, whether it is
done manually or in a production solder reflow environment.
Production quantities of this product are shipped in a standard
tape and reel format.
10
1
RF Output
J2
J4
V2
V4
N/C
RFC
V1
V3
J1
J3
2
DC Control
Voltage (1.8-5.0 V)
CBL
RF Output
8
4
DC Control
Voltage (1.8-5.0 V)
RF Output
9
3
×
CBL
CBL
7
5
6
CBL
DC Control
Voltage (1.8-5.0 V)
RF Common
Input
DC Control
Voltage (1.8-5.0 V)
RF Output
CBL = 47 pF for >1 GHz operation.
Exposed ground paddle should be grounded
for best performance.
Use 10 nF blocking capacitors (CBL) for <50 MHz operation.
S1551
Figure 9. SKY13322-375LF Evaluation Board Schematic
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
201098C • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • August 4, 2010
5
DATA SHEET • SKY13322-375LF SP4T SWITCH
J4
J2
C BL
C BL
V4
V2
RFC
V1
V3
GND
C BL
C BL
J3
J1
S1539
Figure 10. SKY13322-375LF Evaluation Board Assembly Diagram
Component Outline
10X 0.60
Exposed Soldering
Area, Typ.
10X 0.55
10X 0.25
0.50
Pitch
2X 1.20
Pin 10
Pin 1
R0.20
2X 0.38
S1540
Figure 11. SKY13322-375LF PCB Layout Footprint
(Top View)
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
6
August 4, 2010 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 201098C
DATA SHEET • SKY13322-375LF SP4T SWITCH
Pin 1
Indicator
Skyworks Part #
Lot #
Date Code:
(Y = Calendar Year
WW = Week)
Figure 12. Typical Case Markings
(Top View)
C
Seating Plane
10X 0.20 Min.
0.10 C 2X
0.02 +0.03/–0.02
Detail C
0.10 C 2X
1.20 +0.05/–0.07
Detail B
2 Places
2.40 +0.10/–0.15
3.0
–B–
Pin 1
Indicator
4X
3
Exposed Pad
0.38 +0.05/–0.07
0.08 C
B
0.41/0.50
R0.20
Pin 1 Ind.
0.10 C
2.0
A
Top View
Side View
0.40 ± 0.10
0.75 +0.10/–0.15
Bottom View
CL
–A–
0.5 Pitch
0.25 +0.05/–0.07 5
0.10 M C A B
R0.12 Typ.
Detail B
Detail C
10 Places
All measurements are in millimeters.
Dimensioning and tolerancing according to ASME Y14.5M-1994.
Coplanarity applies to the exposed heat sink slug as well as the terminals..
Plating requirement per source control drawing (SCD) 2504.
Dimension applies to metalized terminal and is measured between 0.15 mm and 0.30 mm from terminal tip.
S1541
Figure 13. SKY13322-375LF 6-Pin QFN Package Dimensions
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
201098C • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • August 4, 2010
7
DATA SHEET • SKY13322-375LF SP4T SWITCH
4.00
2.00 ± 0.05 (See Note 3)
ϕ1.50 +0.1/–0
ϕ0.50 Min.
0.30 ± 0.05
1.75 ± 0.10
A
R 0.20 Max
5.50 ± 0.05
(See Note 3)
Bo
Ko
Ao
R 0.3 Typ.
12.0 +0.3
4.00 (See Note 1)
A
Section A
Notes:
1. 10 sprocket hole pitch cumulative tolerance ±0.2.
2. Chambre in compliance with EIA 481.
3. Pocket position relative to sprocket hole measured
as true position of pocket, not pocket hole.
4. Carrier tape: black conductive polycarbonate or polystyrene.
5. Cover tape material: transparent conductive PSA.
6. Cover tape size: 9.3mm width.
7. All measurements are in millimeters.
Ao = 2.30
Bo = 3.30
Ko = 0.75
S1552
Figure 14. SKY13322-375LF Tape and Reel Dimensions
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
8
August 4, 2010 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 201098C
DATA SHEET • SKY13322-375LF SP4T SWITCH
Ordering Information
Model Name
SKY13322-375LF SP4T Switch
Manufacturing Part Number
SKY13322-375LF
Evaluation Kit Part Number
SKY13322-375LF-EVB
Copyright © 2009, 2010 Skyworks Solutions, Inc. All Rights Reserved.
Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein, are provided by
Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the
information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to
update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes.
No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or
information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks Terms and Conditions
of Sale.
THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A
PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY
DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS
SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION,
LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGE.
Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury,
death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any
damages resulting from such improper use or sale.
Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of
products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for
applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifications or parameters.
Skyworks, the Skyworks symbol, and “Breakthrough Simplicity” are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries. Third-party brands
and names are for identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com,
are incorporated by reference.
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
201098C • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • August 4, 2010
9