TI DAC7574IDGSRG4

DAC7574
www.ti.com
SLAS375 – JUNE 2003
QUAD, 12-BIT, LOW-POWER, VOLTAGE OUTPUT,
I C INTERFACE DIGITAL-TO-ANALOG CONVERTER
2
FEATURES
DESCRIPTION
•
•
•
•
•
•
•
The DAC7574 is a low-power, quad channel, 12-bit
buffered voltage output DAC. Its on-chip precision output amplifier allows rail-to-rail output swing to be
achieved. The DAC7574 utilizes an I2C compatible two
wire serial interface supporting high-speed interface
mode with address support of up to four DAC7574s for
a total of 16 channels on the bus.
•
•
•
•
•
Micropower Operation: 600 µA at 5 V VDD
Power-On Reset to Zero
+2.7 V to +5.5 V Analog Power Supply
12-Bit Monotonic
I2C™ Interface Up to 3.4 Mbps
Data Transmit Capability
On-Chip Output Buffer Amplifier, Rail-to-Rail
Operation
Double-Buffered Input Register
Address Support for up to Four DAC7574s
Synchronous Update Support for up to 16
Channels
Operation From -40°C to 105°C
Small 10 Lead MSOP Package
APPLICATIONS
•
•
•
•
•
Process Control
Data Acquisition Systems
Closed-Loop Servo Control
PC Peripherals
Portable Instrumentation
The DAC7574 uses VDD and GND to set the output
range of the DAC. The DAC7574 incorporates a
power-on-reset circuit that ensures that the DAC output
powers up at zero volts and remains there until a valid
write takes place to the device. The DAC7574 contains
a power-down feature, accessed via the internal control
register, that reduces the current consumption of the
device to 200 nA at 5 V.
The low power consumption of this part in normal
operation makes it ideally suited to portable battery
operated equipment. The power consumption is less
than 3mW at VDD = 5 V reducing to 1 µW in power-down
mode.
The DAC7574 is available in a 10-lead MSOP package.
VDD
Data
Buffer A
DAC
Register A
DAC A
VOUTA
VOUTB
VOUTC
Data
Buffer D
DAC
Register D
Buffer
Control
Register
Control
DAC D
VOUTD
14
SCL
I2C Block
Power-Down
Control Logic
SDA
8
A0
A1
Resistor
Network
GND
I2C is a trademark of Philips Corporation.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments
semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include testing of all parameters.
Copyright © 2003, Texas Instruments Incorporated
DAC7574
www.ti.com
SLAS375 – JUNE 2003
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated
circuits be handled with appropriate precautions. Failure to observe proper handling and installation
procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision
integrated circuits may be more susceptible to damage because very small parametric changes could
cause the device not to meet its published specifications.
PACKAGE/ORDERING INFORMATION
PRODUCT
PACKAGE
PACKAGE
DRAWING
NUMBER
SPECIFICATION
TEMPERATURE
RANGE
PACKAGE
MARKING
DAC7574
10-MSOP
DGS
-40°C TO +105°C
D774
ORDERING
NUMBER
TRANSPORT MEDIA
DAC7574IDGS
80 Piece Tube
DAC7574IDGSR
2500 Piece Tape and Reel
PIN DESCRIPTIONS
DGS PACKAGE
(TOPVIEW)
PIN
NAME
VOUTA
1
10 A1
1
VOUTA
Analog output voltage from DAC A
VOUTB
2
9 A0
2
VOUTB
Analog output voltage from DAC B
GND
3
8 VDD
3
GND
VOUTC 4
7 SDA
4
VOUTC
Analog output voltage from DAC C
VOUTD 5
6 SCL
5
VOUTD
Analog output voltage from DAC D
6
SCL
Serial clock input
7
SDA
Serial data input and output
8
VDD
Analog voltage supply input
9
A0
Device address select - I2C
10
A1
Device address select - I2C
DAC7574
DESCRIPTION
Ground reference point for all circuitry on the
part
ABSOLUTE MAXIMUM RATINGS (1)
VDD to GND
–0.3 V to +6 V
Digital input voltage to GND
–0.3 V to VDD + 0.3 V
VOUT to GND
–0.3 V to VDD + 0.3 V
Operating temperature range
– 40°C to +105°C
Storage temperature range
– 65°C to +150°C
Junction temperature range (TJ max)
Power dissipation:
Lead temperature, soldering:
(1)
2
+150°C
Thermal impedance (ΘJA)
270°C/W
Thermal impedance (ΘJC)
77°C/W
Vapor phase (60s)
215°C
Infrared (15s)
220°C
Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to absolute
maximum conditions for extended periods may affect device reliability.
DAC7574
www.ti.com
SLAS375 – JUNE 2003
ELECTRICAL CHARACTERISTICS
VDD = 2.7 V to 5.5 V, RL = 2 kΩ to GND; CL = 200 pF to GND; all specifications -40°C to +105°C, unless otherwise specified.
PARAMETER
STATIC PERFORMANCE (1)
TEST CONDITIONS
Resolution
MIN
TYP
MAX
UNITS
±8
LSB
±1
LSB
12
Bits
Relative accuracy
Differential nonlinearity
Specified monotonic by design
Zero-scale error
5
20
mV
Full-scale error
-0.15
±1.0
% of FSR
± 1.0
% of FSR
Gain error
Zero code error drift
±7
µV/°C
Gain temperature coefficient
±3
ppm of
FSR/°C
OUTPUT CHARACTERISTICS (2)
Output voltage range
Output voltage settling time (full scale)
0
Digital-to-analog glitch impulse
12
µs
1
V/µs
0.25
LSB
-100
dB
1 kHz Sine Wave
RL= ∞
470
pF
RL= 2 kΩ
1000
pF
1 LSB change around major
carry
12
nV-s
0.3
nV-s
1
Ω
VDD= 5 V
50
mA
VDD= 3 V
20
mA
Coming out of power-down
mode, VDD= +5 V
2.5
µs
Coming out of power-down
mode, VDD= +3 V
5
µs
Digital feedthrough
DC output impedance
Short-circuit current
Power-up time
µs
RL = ∞ ; CL = 500 pF
DC crosstalk (channel-to-channel)
Capacitive load stability
V
10
8
Slew rate
AC crosstalk (channel-to-channel)
VDD
RL = ∞; 0 pF < CL < 200 pF
LOGIC INPUTS (2)
±1
Input current
VIN_L, Input low voltage
VIN_H, Input high voltage
0.3xVDD
VDD= 3 V
0.7xVDD
µA
V
V
Pin Capacitance
3
pF
5.5
V
POWER REQUIREMENTS
VDD
2.7
IDD(normal operation), including reference current
Excluding load current
IDD@ VDD=+3.6V to +5.5V
VIH= VDD and VIL=GND
600
900
µA
IDD@ VDD =+2.7V to +3.6V
VIH= VDD and VIL=GND
550
750
µA
IDD (all power-down modes)
IDD@ VDD=+3.6V to +5.5V
VIH= VDD and VIL=GND
0.2
1
µA
IDD@ VDD =+2.7V to +3.6V
VIH= VDD and VIL=GND
0.05
1
µA
ILOAD= 2 mA, VDD= +5 V
93%
POWER EFFICIENCY
IOUT/IDD
(1)
(2)
Linearity tested using a reduced code range of 48 to 4047; output unloaded.
Specified by design and characterization, not production tested.
3
DAC7574
www.ti.com
SLAS375 – JUNE 2003
ELECTRICAL CHARACTERISTICS (continued)
VDD = 2.7 V to 5.5 V, RL = 2 kΩ to GND; CL = 200 pF to GND; all specifications -40°C to +105°C, unless otherwise specified.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNITS
+105
°C
TEMPERATURE RANGE
Specified performance
-40
TIMING CHARACTERISTICS
VDD = 2.7 V to 5.5 V, RL = 2 kΩ to GND; all specifications -40°C to +105°C, unless otherwise specified.
SYMBOL
fSCL
tBUF
tHD; tSTA
tLOW
tHIGH
tSU; tSTA
tSU; tDAT
tHD; tDAT
tRCL
tRCL1
tFCL
4
PARAMETER
SCL clock frequency
Bus free time between a
STOP and START condition
Hold time (repeated) START
condition
LOW period of the SCL clock
HIGH period of the SCL clock
Setup time for a repeated
START condition
Data setup time
Data hold time
Rise time of SCL signal
Rise time of SCL signal after
a repeated START condition
and after an acknowledge
BIT
Fall time of SCL signal
TEST CONDITIONS
MAX
UNITS
Standard mode
MIN
TYP
100
kHz
Fast mode
400
kHz
High-Speed Mode, CB = 100 pF max
3.4
MHz
High-speed mode, CB = 400 pF max
1.7
MHz
Standard mode
4.7
µs
µs
Fast mode
1.3
Standard mode
4.0
µs
Fast mode
600
ns
High-speed mode
160
ns
Standard mode
4.7
µs
Fast mode
1.3
µs
High-speed mode, CB = 100 pF max
160
ns
High-speed mode, CB = 400 pF max
320
ns
Standard mode
4.0
µs
Fast mode
600
ns
High-Speed Mode, CB = 100 pF max
60
ns
High-speed mode, CB = 400 pF max
120
ns
Standard mode
4.7
µs
Fast mode
600
ns
High-speed mode
160
ns
Standard mode
250
ns
Fast mode
100
ns
High-speed mode
10
Standard mode
0
3.45
µs
Fast mode
0
0.9
µs
High-speed mode, CB = 100 pF max
0
70
ns
High-speed mode, CB = 400 pF max
0
150
ns
Standard mode
20 × 0.1CB
1000
ns
Fast mode
ns
20 × 0.1CB
300
ns
High-speed mode, CB = 100 pF max
10
40
ns
High-speed mode, CB = 400 pF max
20
80
ns
Standard mode
20 × 0.1CB
1000
ns
Fast mode
20 × 0.1CB
300
ns
High-speed mode, CB = 100 pF max
10
80
ns
High-speed mode, CB = 400 pF max
20
160
ns
Standard mode
20 × 0.1CB
300
ns
Fast mode
20 × 0.1CB
300
ns
High-speed mode, CB = 100 pF max
10
40
ns
High-speed mode, CB = 400 pF max
20
80
ns
DAC7574
www.ti.com
SLAS375 – JUNE 2003
TIMING CHARACTERISTICS (continued)
VDD = 2.7 V to 5.5 V, RL = 2 kΩ to GND; all specifications -40°C to +105°C, unless otherwise specified.
SYMBOL
tRDA
PARAMETER
Rise time of SDA signal
TEST CONDITIONS
Fall time of SDA signal
tSU; tSTO
Setup time for STOP condition
CB
Capacitive load for SDA and
SCL
tSP
Pulse width of spike suppressed
VNH
Noise margin at the HIGH
level for each connected device (including hysteresis)
VNL
Noise margin at the LOW
level for each connected device (including hysteresis)
TYP
MAX
UNITS
Standard mode
20 × 0.1CB
1000
ns
Fast mode
20 × 0.1CB
300
ns
10
80
ns
High-speed mode, CB = 100 pF max
High-speed mode, CB = 400 pF max
tFDA
MIN
20
160
ns
Standard mode
20 × 0.1CB
300
ns
Fast mode
20 × 0.1CB
300
ns
High-speed mode, CB = 100 pF max
10
80
ns
High-speed mode, CB = 400 pF max
20
160
ns
Standard mode
4.0
µs
Fast mode
600
ns
High-speed mode
160
ns
400
pF
Fast mode
50
ns
High-speed mode
10
ns
Standard mode
Fast mode
0.2 VDD
V
0.1 VDD
V
High-speed mode
Standard mode
Fast mode
High-speed mode
5
DAC7574
www.ti.com
SLAS375 – JUNE 2003
TYPICAL CHARACTERISTICS
At TA = +25°C, unless otherwise noted.
8
6
4
2
0
-2
-4
-6
-8
Channel A
VDD = 5 V
LINEARITY ERROR AND DIFFERENTIAL
LINEARITY ERROR vs DIGITAL INPUT CODE
LE - LSB
LE - LSB
LINEARITY ERROR AND DIFFERENTIAL
LINEARITY ERROR vs DIGITAL INPUT CODE
0.5
0.0
- 0.5
- 1.0
0.5
0.0
- 0.5
512
1024
1536
2048
2560
3072
3584
0
2048
2560
Figure 2.
Channel C
VDD = 5 V
3072
3584
LINEARITY ERROR AND DIFFERENTIAL
LINEARITY ERROR vs DIGITAL INPUT CODE
8
6
4
2
0
-2
-4
-6
-8
Channel D
VDD = 5 V
1.0
DLE - LSB
DLE - LSB
1536
Figure 1.
1.0
0.5
0.0
- 0.5
- 1.0
0.5
0.0
- 0.5
- 1.0
0
512
1024
1536
2048
2560
3072
3584
0
8
6
4
2
0
-2
-4
-6
-8
512
1024
1536
2048
2560
Digital Input Code
Digital Input Code
Figure 3.
Figure 4.
LINEARITY ERROR AND DIFFERENTIAL
LINEARITY ERROR vs DIGITAL INPUT CODE
Channel A
3072
3584
LINEARITY ERROR AND DIFFERENTIAL
LINEARITY ERROR vs DIGITAL INPUT CODE
VDD = 2.7 V
LE - LSB
LE - LSB
1024
Digital Input Code
LE - LSB
LE - LSB
8
6
4
2
0
-2
-4
-6
-8
512
Digital Input Code
LINEARITY ERROR AND DIFFERENTIAL
LINEARITY ERROR vs DIGITAL INPUT CODE
1.0
8
6
4
2
0
-2
-4
-6
-8
Channel B
VDD = 2.7 V
1.0
DLE - LSB
DLE - LSB
VDD = 5 V
- 1.0
0
0.5
0.0
- 0.5
- 1.0
0.5
0.0
- 0.5
- 1.0
0
6
Channel B
1.0
DLE - LSB
DLE - LSB
1.0
8
6
4
2
0
-2
-4
-6
-8
512
1024
1536
2048
2560
3072
3584
0
512
1024
1536
2048
2560
Digital Input Code
Digital Input Code
Figure 5.
Figure 6.
3072
3584
DAC7574
www.ti.com
SLAS375 – JUNE 2003
TYPICAL CHARACTERISTICS (continued)
At TA = +25°C, unless otherwise noted.
Channel C
VDD = 2.7 V
LINEARITY ERROR AND DIFFERENTIAL
LINEARITY ERROR vs DIGITAL INPUT CODE
LE - LSB
LE - LSB
LINEARITY ERROR AND DIFFERENTIAL
LINEARITY ERROR vs DIGITAL INPUT CODE
8
6
4
2
0
-2
-4
-6
-8
Channel D
0.5
0.0
- 0.5
- 1.0
0.5
0.0
- 0.5
- 1.0
0
512
1024
1536
2048
2560
3072
3584
0
512
1024
1536
2560
Digital Input Code
Figure 7.
Figure 8.
3072
3584
ZERO-SCALE ERROR
vs TEMPERATURE
20
15
VDD = 5 V
15
Zero-Scale Error - mV
VDD = 2.7 V
CH A
CH C
CH D
10
CH B
5
10
CH A
CH C
CH D
5
CH B
0
- 40
- 10
20
50
80
- 40
- 10
TA - Free - Air Temperature - °C
20
50
80
TA - Free - Air Temperature - °C
Figure 9.
Figure 10.
FULL-SCALE ERROR
vs TEMPERATURE
FULL-SCALE ERROR
vs TEMPERATURE
30
20
VDD = 5 V
VDD = 2.7 V
25
CH C
Full-Scale Error - mV
Full-Scale Error - mV
2048
Digital Input Code
ZERO-SCALE ERROR
vs TEMPERATURE
Zero-Scale Error - mV
VDD = 2.7 V
1.0
DLE - LSB
DLE - LSB
1.0
8
6
4
2
0
-2
-4
-6
-8
CH A
20
CH D
15
10
CH B
CH C
15
CH A
10
CH D
5
5
CH B
0
0
- 40
- 10
20
50
TA - Free - Air Temperature - °C
Figure 11.
80
- 40
- 10
20
50
80
TA - Free - Air Temperature - °C
Figure 12.
7
DAC7574
www.ti.com
SLAS375 – JUNE 2003
TYPICAL CHARACTERISTICS (continued)
At TA = +25°C, unless otherwise noted.
SINK CURRENT CAPABILITY
AT NEGATIVE RAIL
SOURCE CURRENT CAPABILITY
AT POSITIVE RAIL
0.150
5.50
Typical For All Channels
0.100
VOUT - Output Voltage - V
VOUT - Output Voltage - V
Typical For All Channels
0.125
VDD = 2.7 V
VDD = 5.5 V
0.075
0.050
0.025
5.45
5.40
5.35
DAC Loaded With FFFH
VDD = 5.5 V
DAC Loaded With 000H
0.000
5.30
0
1
2
3
4
0
5
1
ISINK - Sink Current - mA
2
Figure 13.
800
Typical For All Channels
700
IDD - Supply Current - µA
VOUT - Output Voltage - V
5
SUPPLY CURRENT
vs DIGITAL INPUT CODE
2.7
2.6
2.5
2.4
DAC Loaded With FFFH
VDD = 2.7 V
VDD = 5.5 V
600
500
400
VDD = 2.7 V
300
200
100
2.3
All Channels Powered, No Load
0
0
1
2
3
4
5
0
512
1024 1536 2048 2560 3072 3584 4096
ISOURCE - Source Current - mA
Digital Input Code
Figure 15.
Figure 16.
SUPPLY CURRENT
vs TEMPERATURE
SUPPLY CURRENT
vs SUPPLY VOLTAGE
700
700
650
600
IDD - Supply Current - µA
IDD - Supply Current - µA
4
Figure 14.
SOURCE CURRENT CAPABILITY
AT POSITIVE RAIL
VDD = 5.5 V
500
400
VDD = 2.7 V
300
200
100
600
550
500
450
400
350
300
250
All Channels Powered, No Load
0
All DACs Powered, No Load
200
- 40
- 10
20
50
TA - Free - Air Temperature - °C
Figure 17.
8
3
ISOURCE - Source Current - mA
80
110
2.7
3.1
3.5
3.9
4.3
4.7
VDD - Supply Voltage - V
Figure 18.
5.1
5.5
DAC7574
www.ti.com
SLAS375 – JUNE 2003
TYPICAL CHARACTERISTICS (continued)
At TA = +25°C, unless otherwise noted.
SUPPLY CURRENT
vs LOGIC INPUT VOLTAGE
HISTOGRAM
OF CURRENT CONSUMPTION
2000
TA = 25°C
SCL Input (All Other Inputs = GND)
VDD = 5 V
1000
1500
Frequency
IDD - Supply Current - µA
1200
800
VDD = 5.5 V
600
1000
500
400
VDD = 2.7 V
200
0
0
1
2
3
4
500 520 540 560 580 600 620 640 660 680 700 720 740
5
IDD - Current Consumption - µA
VLogic - Logic Input Voltage - V
Figure 19.
Figure 20.
HISTOGRAM
OF CURRENT CONSUMPTION
EXITING
POWER-DOWN MODE
2000
6
VOUT - Output Voltage - V
VDD = 2.7 V
Frequency
1500
1000
500
0
5
VDD = 5 V
Powerup to Code 4000
4
3
2
1
0
-1
400 420 440 460 480 500 520 540 560 580 600 620
Time (2 µs/div)
IDD - Current Consumption - µA
Figure 21.
Figure 22.
2.54
2.52
VDD = 5 V
Code 7FFH to 800H to 7FFH
(Glitch Occurs Every N*256 Code Boundary)
2.50
2.48
2.46
2.44
2.42
2.40
OUTPUT GLITCH (Worst Case)
VOUT - Output Voltage - V (20 mV/div)
VOUT - Output Voltage - V (20 mV/div)
OUTPUT GLITCH (Mid-Scale)
2.56
4.74
4.72
4.70
4.68
VDD = 5 V
Code EFFH to F00H to EFFH
(Glitch Occurs Every N*256 Code
Boundary)
4.66
4.64
4.62
4.60
4.58
4.56
Time (15 µs/div)
Time (15 µs/div)
Figure 23.
Figure 24.
9
DAC7574
www.ti.com
SLAS375 – JUNE 2003
TYPICAL CHARACTERISTICS (continued)
At TA = +25°C, unless otherwise noted.
ABSOLUTE ERROR
ABSOLUTE ERROR
24
18
VDD = 5 V
TA = 25°C
14
Channel A Output
16
12
8
Channel C Output
Output Error - mV
Output Error - mV
20
Channel B Output
10
6
2
-6
0
512
1024
1536
2048
2560
3072
3584
0
Figure 25.
1024
1536
2048
2560
Figure 26.
LARGE SIGNAL
SETTLING TIME
LARGE SIGNAL
SETTLING TIME
3.0
4
VDD = 5 V
Output Loaded with
200 pF to GND
10% to 90% FSR
2
1
0
VOUT - Output Voltage - V
5
VOUT - Output Voltage - V
512
Digital Input Code
Digital Input Code
10
Channel C Output
-2
Channel D Output
0
3
Channel A Output
Channel D Output
Channel B Output
4
VDD = 2.7 V
TA = 25°C
2.5
2.0
1.5
VDD = 2.7 V
Output Loaded with
200 pF to GND
10% to 90% FSR
1.0
0.5
0.0
Time (25 µs/div)
Time (25 µs/div)
Figure 27.
Figure 28.
3072
3584
DAC7574
www.ti.com
SLAS375 – JUNE 2003
THEORY OF OPERATION
D/A SECTION
The architecture of the DAC7574 consists of a string DAC followed by an output buffer amplifier. Figure 29
shows a generalized block diagram of the DAC architecture.
VDD
50 k
50 k
70 k
_
Ref+
Resistor String
Ref-
DAC Register
+
VOUT
GND
Figure 29. R-String DAC Architecture
The input coding to the DAC7574 is unsigned binary, which gives the ideal output voltage as:
V OUT VDD D
4096
(1)
Where D = decimal equivalent of the binary code that is loaded to the DAC register; it can range from 0 to 4095.
RESISTOR STRING
The resistor string section is shown in Figure 30. It is basically a divide-by-2 resistor, followed by a string of
resistors, each of value R. The code loaded into the DAC register determines at which node on the string the
voltage is tapped off to be fed into the output amplifier by closing one of the switches connecting the string to the
amplifier. Because the architecture consists of a string of resistors, it is specified monotonic.
To Output
Amplifier
VDD
GND
R
R
R
R
Figure 30. Typical Resistor String
Output Amplifier
The output buffer is a gain-of-2 noninverting amplifiers, capable of generating rail-to-rail voltages on its output,
which gives an output range of 0V to VDD. It is capable of driving a load of 2 kΩ in parallel with 1000 pF to GND.
The source and sink capabilities of the output amplifier can be seen in the typical curves. The slew rate is 1 V/µs
with a half-scale settling time of 8 µs with the output unloaded.
I2C Interface
I2C is a 2-wire serial interface developed by Philips Semiconductor (see I2C-Bus Specification, Version 2.1,
January 2000). The bus consists of a data line (SDA) and a clock line (SCL) with pullup structures. When the bus
is idle, both SDA and SCL lines are pulled high. All the I2C compatible devices connect to the I2C bus through
open drain I/O pins, SDA and SCL. A master device, usually a microcontroller or a digital signal processor,
controls the bus. The master is responsible for generating the SCL signal and device addresses. The master also
generates specific conditions that indicate the START and STOP of data transfer. A slave device receives and/or
transmits data on the bus under control of the master device.
11
DAC7574
SLAS375 – JUNE 2003
www.ti.com
THEORY OF OPERATION (continued)
The DAC7574 works as a slave and supports the following data transfer modes, as defined in the I2C-Bus
Specification: standard mode (100 kbps), fast mode (400 kbps), and high-speed mode (3.4 Mbps). The data
transfer protocol for standard and fast modes is exactly the same, therefore they are referred to as F/S-mode in
this document. The protocol for high-speed mode is different from the F/S-mode, and it is referred to as
H/S-mode. The DAC7574 supports 7-bit addressing; 10-bit addressing and general call address are not
supported.
F/S-Mode Protocol
•
•
•
•
The master initiates data transfer by generating a start condition. The start condition is when a high-to-low
transition occurs on the SDA line while SCL is high, as shown in Figure 31. All I2C-compatible devices should
recognize a start condition.
The master then generates the SCL pulses, and transmits the 7-bit address and the read/write direction bit
R/W on the SDA line. During all transmissions, the master ensures that data is valid. A valid data condition
requires the SDA line to be stable during the entire high period of the clock pulse (see Figure 32). All devices
recognize the address sent by the master and compare it to their internal fixed addresses. Only the slave
device with a matching address generates an acknowledge (see Figure 33) by pulling the SDA line low
during the entire high period of the 9th SCL cycle. Upon detecting this acknowledge, the master knows that
communication link with a slave has been established.
The master generates further SCL cycles to either transmit data to the slave (R/W bit 1) or receive data from
the slave (R/W bit 0). In either case, the receiver needs to acknowledge the data sent by the transmitter. So
acknowledge signal can either be generated by the master or by the slave, depending on which one is the
receiver. 9-bit valid data sequences consisting of 8-bit data and 1-bit acknowledge can continue as long as
necessary.
To signal the end of the data transfer, the master generates a stop condition by pulling the SDA line from low
to high while the SCL line is high (see Figure 31). This releases the bus and stops the communication link
with the addressed slave. All I2C compatible devices must recognize the stop condition. Upon the receipt of a
stop condition, all devices know that the bus is released, and they wait for a start condition followed by a
matching address.
H/S-Mode Protocol
•
•
•
12
When the bus is idle, both SDA and SCL lines are pulled high by the pullup devices.
The master generates a start condition followed by a valid serial byte containing H/S master code
00001XXX. This transmission is made in F/S-mode at no more than 400 Kbps. No device is allowed to
acknowledge the H/S master code, but all devices must recognize it and switch their internal setting to
support 3.4 Mbps operation.
The master then generates a repeated start condition (a repeated start condition has the same timing as the
start condition). After this repeated start condition, the protocol is the same as F/S-mode, except that
transmission speeds up to 3.4 Mbps are allowed. A stop condition ends the H/S-mode and switches all the
internal settings of the slave devices to support the F/S-mode. Instead of using a stop condition, repeated
start conditions should be used to secure the bus in H/S-mode.
DAC7574
www.ti.com
SLAS375 – JUNE 2003
THEORY OF OPERATION (continued)
SDA
SDA
SCL
SCL
S
P
Start
Condition
Stop
Condition
Figure 31. START and STOP Conditions
SDA
SCL
Data Line
Stable;
Data Valid
Change of Data Allowed
Figure 32. Bit Transfer on the I2C Bus
Data Output
by Transmitter
Not Acknowledge
Data Output
by Receiver
Acknowledge
SCL From
Master
1
2
S
8
9
Clock Pulse for
Acknowledgement
START
Condition
Figure 33. Acknowledge on the I2C Bus
13
DAC7574
www.ti.com
SLAS375 – JUNE 2003
Recognize STOP or
REPEATED START
Condition
Recognize START or
REPEATED START
Condition
Generate ACKNOWLEDGE
Signal
P
SDA
MSB
Acknowledgement
Signal From Slave
Sr
Address
R/W
SCL
S
or
Sr
1
2
7
8
9
ACK
1
2
3-8
9
ACK
Sr
or
P
Clock Line Held Low While
Interrupts are Serviced
START or
Repeated START
Condition
STOP or
Repeated START
Condition
Figure 34. Bus Protocol
DAC7574 I2C Update Sequence
The DAC7574 requires a start condition, a valid I2C address, a control byte, an MSB byte, and an LSB byte for a
single update. After the receipt of each byte, DAC7574 acknowledges by pulling the SDA line low during the high
period of a single clock pulse. A valid I2C address selects the DAC7574. The control byte sets the operational
mode of the selected DAC7574. Once the operational mode is selected by the control byte, DAC7574 expects an
MSB byte followed by an LSB byte for data update to occur. DAC7574 performs an update on the falling edge of
the acknowledge signal that follows the LSB byte.
Control byte needs not to be resent until a change in operational mode is required. The bits of the control byte
continuously determine the type of update performed. Thus, for the first update, DAC7574 requires a start
condition, a valid I2C address, a control byte, an MSB byte and an LSB byte. For all consecutive updates,
DAC7574 needs an MSB byte and an LSB byte as long as the control command remains the same.
Using the I2C high-speed mode (fscl= 3.4 MHz), the clock running at 3.4 MHz, each 12-bit DAC update other than
the first update can be done within 18 clock cycles (MSB byte, acknowledge signal, LSB byte, acknowledge
signal), at 188.88 KSPS. Using the fast mode (fscl= 400 kHz), clock running at 400 kHz, maximum DAC update
rate is limited to 22.22 KSPS. Once a stop condition is received DAC7574 releases the I2C bus and awaits a new
start condition.
Address Byte
MSB
1
LSB
0
0
1
1
A1
A0
R/W
The address byte is the first byte received following the START condition from the master device. The first five
bits (MSBs) of the address are factory preset to 10011. The next two bits of the address are the device select
bits A1 and A0. The A1, A0 address inputs can be connected to VDD or digital GND, or can be actively driven by
TTL/CMOS logic levels. The device address is set by the state of these pins during the power-up sequence of
the DAC7574. Up to 4 devices (DAC7574) can still be connected to the same I2C-Bus.
14
DAC7574
www.ti.com
SLAS375 – JUNE 2003
Broadcast Address Byte
MSB
LSB
1
0
0
1
0
0
0
0
Broadcast addressing is also supported by DAC7574. Broadcast addressing can be used for synchronously
updating or powering down multiple DAC7574 devices. DAC7574 is designed to work with other members of the
DAC857x and DAC757x families to support multichannel synchronous update. Using the broadcast address,
DAC7574 responds regardless of the states of the address pins. Broadcast is supported only in write mode
(Master writes to DAC7574).
Control Byte
MSB
LSB
0
0
L1
L0
X
Sel1
Sel0
PD0
Table 1. Control Register Bit Descriptions
Bit Name
Bit Number/Description
L1
Load1 (Mode Select) Bit
L2
Load0 (Mode Select) Bit
00
Store I2C data. The contents of MS-BYTE and LS-BYTE (or power down information) are stored in the
temporary register of a selected channel. This mode does not change the DAC output of the selected
channel.
01
Update selected DAC with I2C data. Most commonly utilized mode. The contents of MS-BYTE and
LS-BYTE (or power down information) are stored in the temporary register and in the DAC register of
the selected channel. This mode changes the DAC output of the selected channel with the new data.
10
4-Channel synchronous update. The contents of MS-BYTE and LS-BYTE (or power down information)
are stored in the temporary register and in the DAC register of the selected channel. Simultaneously,
the other three channels get updated with previously stored data from the temporary register. This
mode updates all four channels together.
11
Broadcast update mode. This mode has two functions. In broadcast mode, DAC7574 responds
regardless of local address matching, and channel selection becomes irrelevant as all channels update.
This mode is intended to enable up to 16 channels simultaneous update, if used with the I2C broadcast
address (1001 0000).
Sel1
Buff Sel1 Bit
Sel0
Buff Sel0 Bit
PD0
Are used for selecting the update mode.
If Sel1=0
All four channels are updated with the contents of their temporary register
data.
If Sel1=1
All four channels are updated with the MS-BYTE and LS-BYTE data or
powerdown.
Channel Select Bits
00
Channel A
01
Channel B
10
Channel C
11
Channel D
Power Down Flag
0
Normal operation
1
Power-down flag (MSB7 and MSB6 indicate a power-down operation, as shown in Table 2).
15
DAC7574
www.ti.com
SLAS375 – JUNE 2003
Table 2. Control Byte
C7
0
C6
0
C5
C4
C3
Load1
Load0
Don’t
Care
C2
Ch Sel 1
0
0
X
0
0
0
0
C1
C0
MSB7
MSB6
MSB5...
Ch Sel 0
PD0
MSB
(PD1)
MSB-1
(PD2)
MSB-2
...LSB
0
0
0
Data
Write to temporary
register A (TRA) with
data
X
0
1
0
Data
Write to temporary
register B (TRB) with
data
0
X
1
0
0
Data
Write to temporary
register C (TRC) with
data
0
X
1
1
0
Data
Write to temporary
register D (TRD) with
data
DESCRIPTION
(Address
Select)
(00, 01, 10, or 11)
0
0
X
0
1
X
0
1
X
1
0
X
1
0
X
1
see Table 8
0
(00, 01, 10, or 11)
0
Write to TRx (selected
by C2 &C1 and load
DACx w/data
Data
(00, 01, 10, or 11)
1
see Table 8
0
(00, 01, 10, or 11)
0
see Table 8
Power-down DACx
(selected by C2 and
C1)
Write to TRx (selected
by C2 &C1 w/ data and
load all DACs
Data
(00, 01, 10, or 11)
1
Write to TRx (selected
by C2 &C1
w/Powerdown Command
0
Power-down DACx
(selected by C2 and
C1) & load all DACs
Broadcast Modes (controls up to 4 devices on a single serial bus)
X
X
1
1
X
0
X
X
X
Update all DACs, all
devices with previously
stored TRx data
X
X
1
1
X
1
X
0
Data
Update all DACs, all
devices with MSB[7:0]
and LSB[7:0] data
X
X
1
1
X
1
X
1
see Table 8
0
Power-down all DACs,
all devices
Most Significant Byte
Most Significant Byte MSB[7:0] consists of eight most significant bits of 12-bit unsigned binary D/A conversion
data. C0=1, MSB[7], MSB[6] indicate a powerdown operation as shown in Table 8.
Least Significant Byte
Least Significant Byte LSB[7:0] consists of the 4 least significant bits of the 12-bit unsigned binary D/A
conversion data, followed by 4 don’t care bits. DAC7574 updates at the falling edge of the acknowledge signal
that follows the LSB[0] bit.
Default Readback Condition
If the user initiates a readback of a specified channel without first writing data to that specified channel, the
default readback is all zeros, since the readback register is initialized to 0 during the power on reset phase.
16
DAC7574
www.ti.com
SLAS375 – JUNE 2003
LDAC Functionality
Depending on the control byte, DACs are synchronously updated on the falling edge of the acknowledge signal
that follows LS byte. The LDAC pin is required only when an external timing signal is used to update all the
channels of the DAC asynchronously. LDAC is a positive edge triggered asynchronous input that allows four
DAC output voltages to be updated simultaneously with temporary register data. The LDAC trigger should only
be used after the buffers temporary registers are properly updated through software.
DAC7574 Registers
Table 3. DAC7574 Architecture Register Descriptions
Register
Description
CTRL[7:0]
Stores 8-bit wide control byte sent by the master
MSB[7:0]
Stores the 8 most significant bits of unsigned binary data sent by the master. Can also store 2-bit
power-down data.
LSB[7:0]
Stores the 4 least significant bits of unsigned binary data sent by the master.
TRA[13:0], TRB[13:0],
TRC[13:0], TRD[13:0]
14-bit temporary storage registers assigned to each channel. Two MSBs store power-down information, 12
LSBs store data.
DRA[13:0], DRB[13:0],
DRC[13:0], DRD[13:0]
14-bit DAC registers for each channel. Two MSBs store power-down information, 12 LSBs store DAC data.
An update of this register means a DAC update with data or power-down.
DAC7574 as a Slave Receiver - Standard and Fast Mode
Figure 35 shows the standard and fast mode master transmitter addressing a DAC7574 Slave Receiver with a
7-bit address.
S SLAVE ADDRESS R/W A Ctrl-Byte A MS-Byte A LS-Byte
”0” (write)
A/A
P
Data Transferred
(n* Words + Acknowledge)
Word = 12 Bit
From Master to DAC7574
DAC7574 I2C-SLAVE ADDRESS:
From DAC7574 to Master
MSB
A =
A =
S =
Sr =
P =
Acknowledge (SDA LOW)
Not Acknowledge (SDA HIGH)
START Condition
Repeated START Condition
STOP Condition
1
LSB
0
0
1
1
A1
A0
R/W
‘0’ = Write to DAC7574
‘1’ = Read from DAC7574
Factory Preset
A0 = I2C Address Pin
A1 = I2C Address Pin
Figure 35. Standard and Fast Mode: Slave Receiver
17
DAC7574
www.ti.com
SLAS375 – JUNE 2003
DAC7574 as a Slave Receiver - High-Speed Mode
Figure 36 shows the high-speed mode master transmitter addressing a DAC7574 Slave Receiver with a 7-bit
address.
F/S-Mode
S
HS-Mode
HS-Master Code
A Sr Slave Address
F/S-Mode
R/W A Ctrl-Byte A MS-Byte A LS-Byte
Data Transferred
(n* Words + Acknowledge)
Word = 12 Bit
”0” (write)
HS-Mode Master Code:
0
0
0
1
X
X
R/X
Control Byte:
LSB
0
0
L1
L0
X
Sel1 Sel2 PD0
MS-Byte:
MSB
LSB
D10
D9
D8
D7
D6
D5
D1
D0
X
X
X
D4
LS-Byte:
MSB
D3
L1
L0
Sel1
Sel0
PD0
=
=
=
=
=
Load1 (Mode Select) Bit
Load0 (Mode Select) Bit
Buff Sel1 (Channel) Select Bit
Buff Sel0 (Channel) Select Bit
Power Down Flag
X
= Don’t Care
LSB
D2
X
D11 - D0 = Data Bits
Figure 36. High-Speed Mode: Slave Receiver
18
HS-Mode Continues
LSB
MSB
D11
P
Sr Slave Address
MSB
0
A/A
DAC7574
www.ti.com
SLAS375 – JUNE 2003
Master Transmitter Writing to a Slave Receiver (DAC7574) in Standard/Fast Modes
All write access sequences begin with the device address (with R/W = 0) followed by the control byte. This
control byte specifies the operation mode of DAC7574 and determines which channel of DAC7574 is being
accessed in the subsequent read/write operation. The LSB of the control byte (PD0-Bit) determines if the
following data is power-down data or regular data.
With (PD0-Bit = 0) the DAC7574 expects to receive data in the following sequence HIGH-BYTE –LOW-BYTE –
HIGH-BYTE – LOW-BYTE..., until a STOP Condition or REPEATED START Condition on the I2C-Bus is
recognized (refer to the DATA INPUT MODE section of Table 4).
With (PD0-Bit = 1) the DAC7574 expects to receive 2 Bytes of power-down data (refer to the POWER DOWN
MODE section of Table 4).
Table 4. Write Sequence in F/S Mode
DATA INPUT MODE
Transmitter
MSB
6
5
4
1
0
0
1
Master
Master
0
0
Load 1
D11
D10
D9
LSB
1
Comment
A1
A0
R/W
Write addressing (R/W=0)
Buff Sel 0
PD0
Control byte (PD0=0)
D5
D4
Writing data word, high byte
x
x
Writing data word, low byte
Begin sequence
Load 0
x
Buff Sel 1
DAC7574 Acknowledges
DAC7574
Master
1
DAC7574 Acknowledges
DAC7574
Master
2
Start
DAC7574
Master
3
D8
D7
D6
DAC7574 Acknowledges
D3
D2
D1
DAC7574
D0
x
x
DAC7574 Acknowledges
Data or Stop or Repeated Start (1)
Master
Data or done (2)
POWER DOWN MODE
Transmitter
MSB
6
5
4
Master
Master
1
0
0
0
0
Load 1
DAC7574
Master
DAC7574
Master
(1)
(2)
1
LSB
1
1
Comment
Begin sequence
A1
A0
R/W
Write addressing (R/W=0)
Load 0
x
Buff Sel 0
PD0
Control byte (PD0 = 1)
0
0
0
Writing data word, high byte
x
x
x
Writing data word, low byte
Buff Sel 1
DAC7574 Acknowledges
PD1
PD2
0
DAC7574
Master
2
DAC7574 Acknowledges
DAC7574
Master
3
Start
0
0
DAC7574 Acknowledges
0
0
0
0
x
DAC7574 Acknowledges
Stop or Repeated Start (1)
Done
Use repeated START to secure bus operation and loop back to the stage of write addressing for next Write.
Once DAC7574 is properly addressed and control byte is sent, HIGH–BYTE–LOW–BYTE sequences can repeat until a STOP
condition or repeated START condition is received.
19
DAC7574
www.ti.com
SLAS375 – JUNE 2003
Master Transmitter Writing to a Slave Receiver (DAC7574) in HS Mode
When writing data to the DAC7574 in HS-mode, the master begins to transmit what is called the HS-Master
Code (0000 1XXX) in F/S-mode. No device is allowed to acknowledge the HS-Master Code, so the HS-Master
Code is followed by a NOT acknowledge.
The master then switches to HS-mode and issues a repeated start condition, followed by the address byte (with
R/W = 0) after which the DAC7574 acknowledges by pulling SDA low. This address byte is usually followed by
the control byte, which is also acknowledged by the DAC7574. The LSB of the control byte (PD0-Bit) determines
if the following data is power-down data or regular data.
With (PD0-Bit = 0) the DAC7574 expects to receive data in the following sequence HIGH-BYTE – LOW-BYTE –
HIGH-BYTE – LOW-BYTE...., until a STOP condition or repeated start condition on the I2C-Bus is recognized
(refer to Table 5 HS-MODE WRITE SEQUENCE - DATA).
With (PD0-Bit = 1) the DAC7574 expects to receive 2 bytes of power-down data (refer to Table 5 HS-MODE
WRITE SEQUENCE - POWER DOWN).
Table 5. Master Transmitter Writes to Slave Receiver (DAC7574) in HS-Mode
HS MODE WRITE SEQUENCE - DATA
Transmitter
MSB
6
5
4
Master
Master
0
0
0
0
NONE
0
0
1
0
0
Load 1
Comment
Begin sequence
1
X
X
X
HS Mode Master Code
No device may acknowledge HS master code
1
A1
A0
R/W
Write addressing (R/W=0)
Load 0
0
Buff Sel 1
Buff Sel 0
PD0
Control byte (PD0=0)
D5
D4
Writing data word, MSB
x
x
Writing data word, LSB
DAC7574 Acknowledges
D11
D10
D9
DAC7574
Master
LSB
DAC7574 Acknowledges
DAC7574
Master
1
Repeated Start
1
DAC7574
Master
2
Not Acknowledge
Master
Master
3
Start
D8
D7
D6
DAC7574 Acknowledges
D3
D2
D1
DAC7574
D0
x
x
DAC7574 Acknowledges
Data or Stop or Repeated Start (1)
Master
Data or done (2)
HS MODE WRITE SEQUENCE - POWER DOWN
Transmitter
MSB
6
5
4
0
0
0
0
Master
Master
0
0
0
0
Load 1
Master
(1)
(2)
20
X
X
Begin sequence
1
HS Mode Master Code
No device may acknowledge HS master code
1
1
A1
A0
R/W
Write addressing (R/W = 0)
Load 2
0
Buff Sel 0
PD0
Control Byte (PD0=1)
0
0
0
Writing data word, high byte
x
x
x
Writing data word, low byte
Buff Sel 1
DAC7574 Acknowledges
PD1
PD2
0
0
0
0
DAC7574
DAC7574
X
Comment
DAC7574 Acknowledges
DAC7574
Master
LSB
Repeated Start
1
DAC7574
Master
1
Not Acknowledge
Master
Master
2
Start
NONE
Master
3
0
0
DAC7574 Acknowledges
0
x
DAC7574 Acknowledges
Stop or repeated start (1)
Done
Use repeated start to secure bus operation and loop back to the stage of write addressing for next Write.
Once DAC7574 is properly addressed and control byte is sent, high-byte-low-byte sequences can repeat until a stop or repeated start
condition is received.
DAC7574
www.ti.com
SLAS375 – JUNE 2003
DAC7574 as a Slave Transmitter - Standard and Fast Mode
Figure 37 shows the standard and fast mode master transmitter addressing a DAC7574 Slave Transmitter with a
7-bit address.
(DAC7574)
(DAC7574)
(MASTER)
(DAC7574)
S SLAVE ADDRESS R/W A Ctrl <7:1> PD0 A Sr Slave Address
R/W A MS-Byte A LS-Byte A P
’1’ (read)
’0’ (write)
’0’ = (Normal Mode)
Data Transferred
(2 Bytes + Acknowledge)
(DAC7574)
PD0 A Sr Slave Address
’1’ = (Power Down Flag)
(MASTER)
R/W A PDN-Byte A
(MASTER)
(MASTER)
MS-Byte A LS-Byte A P
Data Transferred
(3 Bytes + Acknowledge)
’1’ (read)
PDN-Byte:
MSB
(MASTER)
LSB
PD1 PD2
1
1
1
1
1
1
PD1 = Power-Down Bit
PD2 = Power-Down Bit
Figure 37. Standard and Fast Mode: Slave Transmitter
DAC7574 as a Slave Transmitter - High-Speed Mode
Figure 38 shows an I2C-Master addressing DAC7574 in high-speed mode (with a 7-bit address), as a Slave
Transmitter.
F/S-Mode
S
HS-Master Code
A
HS-Mode
(DAC7574)
Sr
Slave Address
(DAC7574)
R/W A Ctrl <7:1> PD0 A
Sr
(DAC7574)
Slave Address
’0’ = (Normal Mode)
Data Transferred
(2 Bytes + Acknowledge)
(DAC7574)
PD0 A Sr Slave Address
’1’ = (Power -Down Flag)
(MASTER)
R/W A MS-Byte A LS-Byte A P
’1’ (read)
’0’ (write)
(MASTER)
(MASTER)
R/W A PDN-Byte A
’1’ (read)
(MASTER)
(MASTER)
MS-Byte A LS-Byte A P
Data Transferred
(3 Bytes + Acknowledge)
Figure 38. High-Speed Mode: Slave Transmitter
21
DAC7574
www.ti.com
SLAS375 – JUNE 2003
Master Receiver Reading From a Slave Transmitter (DAC7574) in Standard/Fast Modes
When reading data back from the DAC7574, the user begins with an address byte (with R/W = 0) after which the
DAC7574 will acknowledge by pulling SDA low. This address byte is usually followed by the Control Byte, which
is also acknowledged by the DAC7574. Following this there is a REPEATED START condition by the Master and
the address is resent with (R/W = 1). This is acknowledged by the DAC7574, indicating that it is prepared to
transmit data. Two or three bytes of data are then read back from the DAC7574, depending on the (PD0-Bit).
The value of Buff-Sel1 and Buff-Sel0 determines, which channel data is read back. A STOP Condition follows.
With the (PD0-Bit = 0) the DAC7574 transmits 2 bytes of data, HIGH-BYTE followed by the LOW-BYTE (refer to
Table 2. Data Readback Mode - 2 bytes).
With the (PD0-Bit = 1) the DAC7574 transmits 3 bytes of data, POWER-DOWN-BYTE followed by the
HIGH-BYTE followed by the LOW-BYTE (refer to Table 2. Data Readback Mode - 3 bytes).
Table 6. Read Sequence in F/S Mode
DATA READBACK MODE - 2 BYTES
Transmitter
MSB
6
5
4
1
0
0
1
3
Master
Master
0
0
Load 1
Comment
A0
R/W
Write addressing (R/W=0)
Buff Sel 1
Buff Sel 0
PD0
Control byte (PD0=0)
A1
A0
R/W
Read addressing (R/W = 1)
D6
D5
D4
x
x
x
Begin sequence
x
DAC7574 Acknowledges
Repeated Start
1
0
0
D11
D10
D9
DAC7574
1
1
DAC7574 Acknowledges
Master
DAC7574
A1
1
Load 0
Master
DAC7574
LSB
DAC7574 Acknowledges
DAC7574
Master
1
Start
DAC7574
Master
2
D8
D7
Reading data word, high byte
Master Acknowledges
D3
D2
D1
Master
D0
x
Master Not Acknowledges
Stop or Repeated Start (1)
Master
Reading data word, low byte
Master signal end of read
Done
DATA READBACK MODE - 3 BYTES
Transmitter
MSB
6
5
4
3
Master
Master
1
0
0
1
0
0
Load 1
Load 0
DAC7574
Master
0
0
PD1
PD2
1
D11
D10
D9
Master
(1)
22
A0
R/W
Write addressing (R/W=0)
Buff Sel 1
Buff Sel 0
PD0
Control byte (PD0=1)
A1
A0
R/W
Read addressing (R/W = 1)
1
1
1
D6
D5
D4
x
x
x
Begin sequence
x
1
1
1
1
Read power down byte
Master Acknowledges
Master
Master
A1
1
DAC7574 Acknowledges
Master
DAC7574
Comment
Repeated Start
1
DAC7574
DAC7574
LSB
DAC7574 Acknowledges
Master
DAC7574
1
DAC7574 Acknowledges
DAC7574
Master
2
Start
D8
D7
Reading data word, high byte
Master Acknowledges
D3
D2
D1
D0
x
Master Not Acknowledges
Stop or Repeated Start (1)
Reading data word, low byte
Master signal end of read
Done
Use repeated start to secure bus operation and loop back to the stage of write addressing for next Write.
DAC7574
www.ti.com
SLAS375 – JUNE 2003
Master Receiver Reading From a Slave Transmitter (DAC7574) in HS-Mode
When reading data to the DAC7574 in HS-MODE, the master begins to transmit, what is called the HS-Master
Code (0000 1XXX) in F/S-mode. No device is allowed to acknowledge the HS-Master Code, so the HS-Master
Code is followed by a NOT acknowledge.
The Master then switches to HS-mode and issues a REPEATED START condition, followed by the address byte
(with R/W = 0) after which the DAC7574 acknowledges by pulling SDA low. This address byte is usually followed
by the control byte, which is also acknowledged by the DAC7574.
Then there is a REPEATED START condition initiated by the master and the address is resent with (R/W = 1).
This is acknowledged by the DAC7574, indicating that it is prepared to transmit data. Two or Three bytes of data
are then read back from the DAC7574, depending on the (PD0-Bit). The value of Buff-Sel1 and Buff-Sel0
determines, which channel data is read back. A STOP condition follows.
With the (PD0-Bit = 0) the DAC7574 transmits 2 bytes of data, HIGH-BYTE followed by LOW-BYTE (refer to
Table 7 HS-Mode Readback Sequence).
With the (PD0-Bit = 1) the DAC7574 transmits 3 bytes of data, POWER-DOWN-BYTE followed by the
HIGH-BYTE followed by the LOW-BYTE (refer to Table 7 HS-Mode Readback Sequence).
Table 7. Master Receiver Reading Slave Transmitter (DAC7574) in HS-Mode
HS MODE READBACK SEQUENCE
Transmitter
MSB
6
5
4
0
0
0
0
3
Master
Master
0
0
1
0
0
Load 1
X
HS Mode Master Code
No device may acknowledge HS
master code
1
A1
A0
R/W
Write addressing (R/W=0)
Load 0
X
Buff Sel 1
Buff Sel 0
PD0
Control byte (PD0 = 1)
A0
R/W
Read addressing (R/W=1)
1
1
Power-down byte
D5
D4
Reading data word, high byte
x
x
Reading data word, low byte
DAC7574 Acknowledges
Repeated Start
1
0
0
PD1
PD2
1
DAC7574
1
1
A1
DAC7574 Acknowledges
Master
1
1
1
Master Acknowledges
D11
D10
D9
Master
DAC7574
X
DAC7574 Acknowledges
Master
DAC7574
X
Repeated Start
1
DAC7574
DAC7574
Comment
Not Acknowledge
DAC7574
Master
LSB
Begin sequence
1
Master
Master
1
Start
NONE
Master
2
D8
D7
D6
Master Acknowledges
D3
D2
D1
D0
x
x
Master
Master Not Acknowledges
Master signal end of read
Master
Stop or Repeated Start
Done
Power-On Reset
The DAC7574 contains a power-on-reset circuit that controls the output voltage during power up. On power up,
the DAC register is filled with zeros and the output voltage is 0 V; it remains there until a valid write sequence is
made to the DAC. This is useful in applications where it is important to know the state of the output of the DAC
while it is in the process of powering up. No device pin should be brought high before supply is applied.
23
DAC7574
www.ti.com
SLAS375 – JUNE 2003
Power-Down Modes
The DAC7574 contains four separate power-down modes of operation. The modes are programmable via two
most significant bits of the MSB byte, while (CTRL[0] = PD0 = 1). Table 8 shows how the state of these bits
correspond to the mode of operation of the device.
Table 8. Power-Down Modes of Operation for the DAC7574
CTRL[0]
MSB[7]
MSB[6]
OPERATING MODE
1
0
0
High Impedance Output
1
0
1
1 kΩ to GND
1
1
0
100 kΩ to GND
1
1
1
High Impedance
When (CTRL[0] = PD0 = 0), the device works normally with its normal power consumption of 150 µA at 5 V per
channel. However, for the three power-down modes, the supply current falls to 200 nA at 5 V (50 nA at 3 V). Not
only does the supply current fall but also the output stage is also internally switched from the output of the
amplifier to a resistor network of known values. This has the advantage that the output impedance of the device
is known while in power-down mode. There are three different options: The output is connected internally to GND
through a 1 kΩ resistor, a 100 kΩ resistor or left open-circuit (high impedance). The output stage is illustrated in
Figure 39.
Amplifier
Resistor
String DAC
VOUT
Powerdown
Circuitry
Resistor
Network
Figure 39. Output Stage During Power Down
All linear circuitry is shut down when the power-down mode is activated. However, the contents of the DAC
register are unaffected when in power-down. The time to exit power down is typically 2.5 µs for VDD = 5 V and 5
µs for VDD = 3 V. (See the Typical Curves section for additional information.)
The DAC7574 offers a flexible power-down interface based on channel register operation. A channel consists of
a single 12 bit DAC with power-down circuitry, a temporary storage register (TR) and a DAC register (DR). TR
and DR are both 14 bits wide. Two MSBs represent the power-down condition and the 12 LSBs represent data
for TR and DR. By using bits 13 and 14 of TR and DR, a power-down condition can be temporarily stored and
used just like data. Internal circuits ensure that MSB[7] and MSB[6] get transferred to TR[13] and TR[12] (DR[13]
and DR[12]) when the power-down flag (CTRL[0] = PD0) is set. Therefore, DAC7574 treats power-down
conditions like data and all the operational modes are still valid for power down. It is possible to broadcast a
power-down condition to all the DAC7574s in the system, or it is possible to simultaneously power down a
channel while updating data on other channels.
CURRENT CONSUMPTION
The DAC7574 typically consumes 150µA at VDD = 5 V and 125µA at VDD = 3 V for each active channel, including
reference current consumption. Additional current consumption can occur at the digital inputs if VIH << VDD. For
most efficient power operation, CMOS logic levels are recommended at the digital inputs to the DAC. In
power-down mode, typical current consumption is 200 nA. A delay time of 10 to 20 ms after a power-down
command is issued to the DAC is typically sufficient for the power-down current to drop below 10 µA.
24
www.ti.com
DAC7574
SLAS375 – JUNE 2003
DRIVING RESISTIVE AND CAPACITIVE LOADS
The DAC7574 output stage is capable of driving loads of up to 1000 pF while remaining stable. Within the offset
and gain error margins, the DAC7574 can operate rail-to-rail when driving a capacitive load. Resistive loads of 2
kΩ can be driven by the DAC7574 while achieving a typical load regulation of 1%. As the load resistance drops
below 2 kΩ, the load regulation error increases. When the outputs of the DAC are driven to the positive rail under
resistive loading, the PMOS transistor of each Class-AB output stage can enter into the linear region. When this
occurs, the added IR voltage drop deteriorates the linearity performance of the DAC. This only occurs within
approximately the top 20 mV of the DAC’s digital input-to-voltage output transfer characteristic. The reference
voltage applied to the DAC7574 may be reduced below the supply voltage applied to VDD in order to eliminate
this condition if good linearity is a requirement at full scale (under resistive loading conditions).
CROSSTALK
The DAC7574 architecture uses separate resistor strings for each DAC channel in order to achieve ultra-low
crosstalk performance. DC crosstalk seen at one channel during a full-scale change on the neighboring channel
is typically less than 0.5 LSBs. The ac crosstalk measured (for a full-scale, 1 kHz sine wave output generated at
one channel, and measured at the remaining output channel) is typically under -100 dB.
OUTPUT VOLTAGE STABILITY
The DAC7574 exhibits excellent temperature stability of ±3 ppm/°C typical output voltage drift over the specified
temperature range of the device. This enables the output voltage of each channel to stay within a ±25 µV window
for a ±1°C ambient temperature change. Combined with good dc noise performance and true 12-bit differential
linearity, the DAC7574 becomes a perfect choice for closed-loop control applications.
SETTLING TIME AND OUTPUT GLITCH PERFORMANCE
Settling time to within the 12-bit accurate range of the DAC7574 is achievable within 10 µs for a full-scale code
change at the input. Worst case settling times between consecutive code changes is typically less than 2 µs. The
high-speed serial interface of the DAC7574 is designed in order to support up to 188ksps update rate. For
full-scale output swings, the output stage of each DAC7574 channel typically exhibits less than 100 mV of
overshoot and undershoot when driving a 200 pF capacitive load. Code-to-code change glitches are extremely
low (~10 µV) given that the code-to-code transition does not cross an Nx256 code boundary. Due to internal
segmentation of the DAC7574, code-to-code glitches occur at each crossing of an Nx256 code boundary. These
glitches can approach 100 mVs for N = 15, but settle out within ~2 µs. Sufficient bypass capacitance is required
to ensure 10 µs settling under capacitive loading. To observe the settling performance under resistive load
conditions, the power supply (hence DAC7574 reference supply) must settle quicker than the DAC7574.
25
DAC7574
www.ti.com
SLAS375 – JUNE 2003
APPLICATION INFORMATION
The following sections give example circuits and tips for using the DAC7574 in various applications. For more
information, contact your local TI representative, or visit the Texas Instruments website at http://www.ti.com.
BASIC CONNNECTIONS
For many applications, connecting the DAC7574 is extremely simple. A basic connection diagram for the
DAC7574 is shown in Figure 40. The 0.1 µF bypass capacitors help provide the momentary bursts of extra
current needed from the supplies.
DAC7574
I2C Pullup Resistors
1 kΩ to 10 kΩ (typical)
VDD
1 VOUTA
A1 10
2 VOUTB
A0
9
3 GND
VDD 8
4 VOUTC
SDA 7
5 VOUTD
SCL 6
Microcontroller or
Microprocessor With
I2C Port
SCL
SDA
NOTE: DAC7574 power and input/output connections are omitted for clarity, except IC Inputs.
Figure 40. Typical DAC7574 Connections
The DAC7574 interfaces directly to standard mode, fast mode and high-speed mode I2C controllers. Any
microcontroller’s I2C peripheral, including master-only and non-multiple-master I2C peripherals, work with the
DAC7574. The DAC7574 does not perform clock-stretching (i.e., it never pulls the clock line low), so it is not
necessary to provide for this unless other devices are on the same I2C bus.
Pullup resistors are necessary on both the SDA and SCL lines because I2C bus drivers are open-drain. The size
of the these resistors depend on the bus operating speed and capacitance on the bus lines. Higher-value
resistors consume less power, but increase the transition times on the bus, limiting the bus speed. Lower-value
resistors allow higher speed at the expense of higher power consumption. Long bus lines have higher
capacitance and require smaller pullup resistors to compensate. If the pullup resistors are too small the bus
drivers may not be able to pull the bus line low.
USING GPIO PORTS FOR I2C
Most microcontrollers have programmable input/output pins that can be set in software to act as inputs or
outputs. If an I2C controller is not available, the DAC7574 can be connected to GPIO pins, and the I2C bus
protocol simulated, or bit-banged, in software. An example of this for a single DAC7574 is shown in Figure 41.
26
DAC7574
www.ti.com
SLAS375 – JUNE 2003
APPLICATION INFORMATION (continued)
DAC7574
VDD
1 VOUTA
A1 10
2 VOUTB
A0
9
3 GND
VDD
8
4 VOUTC
SDA 7
5 VOUTD
SCL 6
Microcontroller or
Microprocessor
GPIO-1
GPIO-2
NOTE: DAC7574 power and input/output connections are omitted for clarity, except IC Inputs.
Figure 41. Using GPIO With a Single DAC7574
Bit-banging I2C with GPIO pins can be done by setting the GPIO line to zero and toggling it between input and
output modes to apply the proper bus states. To drive the line low, the pin is set to output a zero; to let the line
go high, the pin is set to input. When the pin is set to input, the state of the pin can be read; if another device is
pulling the line low, this reads as a zero in the port’s input register.
Note that no pullup resistor is shown on the SCL line. In this simple case the resistor is not needed. The
microcontroller can simply leave the line on output, and set it to one or zero as appropriate. It can do this
because the DAC7574 never drives its clock line low. This technique can also be used with multiple devices, and
has the advantage of lower current consumption due to the absence of a resistive pullup.
If there are any devices on the bus that may drive their clock lines low, the above method should not be used.
The SCL line should be high-Z or zero, and a pullup resistor provided as usual. Note also that this cannot be
done on the SDA line in any case, because the DAC7574 drives the SDA line low from time to time, as all I2C
devices do.
Some microcontrollers have selectable strong pullup circuits built in to their GPIO ports. In some cases, these
can be switched on and used in place of an external pullup resistor. Weak pullups are also provided on some
microcontrollers, but usually these are too weak for I2C communication. Test any circuit before committing it to
production.
27
DAC7574
www.ti.com
SLAS375 – JUNE 2003
APPLICATION INFORMATION (continued)
POWER SUPPLY REJECTION
The positive reference voltage input of DAC7574 is internally tied to the power supply pin of the device. This
increases I2C system flexibility, creating room for an extra I2C address pin in a low pin-count package. To
eliminate the supply noise appearing at the DAC output, the user must pay close attention to how DAC7574 is
powered. The supply to DAC7574 must be clean and well regulated. For best performance, use of a precision
voltage reference is recommended to supply power to DAC7574. This is equivalent to providing a precision
external reference to the device. Due to low power consumption of DAC7574, load regulation errors are
negligible. In order to avoid excess power consumption at the Schmitt-triggered inputs of DAC7574, the precision
reference voltage should be close to the I2C bus pullup voltage. For 3-V, 3.3-V and 5-V I2C bus pullup voltages,
REF2930, REF2933 and REF02 precision voltage references are recommended respectively. These precision
voltage references can be used to supply power for multiple devices on a system.
USING REF02 AS A POWER SUPPLY FOR DAC7574
Due to the extremely low supply current required by the DAC7574, a possible configuration is to use a REF02
+5 V precision voltage reference to supply the required voltage to the DAC7574’s supply input as well as the
reference input, as shown in Figure 42. This is especially useful if the power supply is quite noisy or if the system
supply voltages are at some value other than 5 V. The REF02 outputs a steady supply voltage for the DAC7574.
If the REF02 is used, the current it needs to supply to the DAC7574 is 600 µA typical and 900 µA max for
VDD = 5 V. When a DAC output is loaded, the REF02 also needs to supply the current to the load. The total
typical current required (with a 5-kΩ load on a single DAC output) is:
600 µA + (5 V / 5 kΩ) = 1.6 mA
The load regulation of the REF02 is typically 0.005%/mA, which results in an error of 400µV for 1.6-mA of current
drawn from it. This corresponds to a 0.33 LSB error for a 0 V to 5 V output range.
15 V
REF02
5V
1.6 mA
I2C
Interface
SCL
SDA
VDD
DAC7574
VOUT = 0 V to 5 V
Figure 42. REF02 Power Supply
LAYOUT
A precision analog component requires careful layout, adequate bypassing, and clean, well-regulated power
supplies.
The power applied to VDD should be well-regulated and low noise. Switching power supplies and dc/dc
converters often have high-frequency glitches or spikes riding on the output voltage. In addition, digital
components can create similar high-frequency spikes as their internal logic switches states. This noise can easily
couple into the DAC output voltage through various paths between the power connections and analog output.
28
www.ti.com
DAC7574
SLAS375 – JUNE 2003
As with the GND connection, VDD should be connected to a positive power-supply plane or trace that is separate
from the connection for digital logic until they are connected at the power-entry point. In addition, a 1 µF to 10 µF
capacitor in parallel with a 0.1 µF bypass capacitor is strongly recommended. In some situations, additional
bypassing may be required, such as a 100 µF electrolytic capacitor or even a Pi filter made up of inductors and
capacitors—all designed to essentially low-pass filter the –5 V supply, removing the high-frequency noise.
29
PACKAGE OPTION ADDENDUM
www.ti.com
3-Mar-2013
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package Qty
Drawing
Eco Plan
Lead/Ball Finish
(2)
MSL Peak Temp
Op Temp (°C)
Top-Side Markings
(3)
(4)
DAC7574IDGS
ACTIVE
VSSOP
DGS
10
80
Green (RoHS CU NIPDAUAG Level-2-260C-1 YEAR
& no Sb/Br)
-40 to 105
D774
DAC7574IDGSG4
ACTIVE
VSSOP
DGS
10
80
Green (RoHS CU NIPDAUAG Level-2-260C-1 YEAR
& no Sb/Br)
-40 to 105
D774
DAC7574IDGSR
ACTIVE
VSSOP
DGS
10
2500
Green (RoHS CU NIPDAUAG Level-2-260C-1 YEAR
& no Sb/Br)
-40 to 105
D774
DAC7574IDGSRG4
ACTIVE
VSSOP
DGS
10
2500
Green (RoHS CU NIPDAUAG Level-2-260C-1 YEAR
& no Sb/Br)
-40 to 105
D774
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
Only one of markings shown within the brackets will appear on the physical device.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
3-Mar-2013
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
19-Nov-2012
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
DAC7574IDGSR
Package Package Pins
Type Drawing
VSSOP
DGS
10
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
2500
330.0
12.4
Pack Materials-Page 1
5.3
B0
(mm)
K0
(mm)
P1
(mm)
3.4
1.4
8.0
W
Pin1
(mm) Quadrant
12.0
Q1
PACKAGE MATERIALS INFORMATION
www.ti.com
19-Nov-2012
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
DAC7574IDGSR
VSSOP
DGS
10
2500
367.0
367.0
35.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated