TOSHIBA TLP250

TLP250
TOSHIBA Photocoupler GaAlAs Ired & Photo−IC
TLP250
Transistor Inverter
Inverter For Air Conditionor
IGBT Gate Drive
Power MOS FET Gate Drive
Unit in mm
The TOSHIBA TLP250 consists of a GaAlAs light emitting diode and a
integrated photodetector.
This unit is 8−lead DIP package.
TLP250 is suitable for gate driving circuit of IGBT or power MOS FET.
•
Input threshold current: IF=5mA(max.)
•
Supply current (ICC): 11mA(max.)
•
Supply voltage (VCC): 10−35V
•
Output current (IO): ±1.5A (max.)
•
Switching time (tpLH/tpHL): 1.5µs(max.)
•
Isolation voltage: 2500Vrms(min.)
•
UL recognized: UL1577, file No.E67349
•
Option (D4) type
VDE approved: DIN VDE0884/06.92,certificate No.76823
Maximum operating insulation voltage: 630VPK
TOSHIBA
Weight: 0.54 g
11−10C4
Highest permissible over voltage: 4000VPK
•
(Note) When a VDE0884 approved type is needed,
please designate the "option (D4)"
Creepage distance: 6.4mm(min.)
Clearance: 6.4mm(min.)
Schmatic
Pin Configuration (top view)
ICC
VCC
8
(Tr 1)
IF
2+
7
VF
3IO
(Tr 2)
6
8
2
7
3
6
4
5
VO
VO
GND
A 0.1µF bypass capcitor must be
connected between pin 8 and 5 (See Note 5).
1
5
1 : N.C.
2 : Anode
3 : Cathode
4 : N.C.
5 : GND
6 : VO (Output)
7 : VO
8 : VCC
Truth Table
Input
LED
Tr1
Tr2
On
On
Off
Off
Off
On
1
2004-06-25
TLP250
Absolute Maximum Ratings (Ta = 25°C)
Characteristic
Symbol
Rating
Unit
IF
20
mA
∆IF / ∆Ta
−0.36
mA / °C
IFPT
1
A
Reverse voltage
VR
5
V
Junction temperature
Tj
125
°C
Forward current
LED
Forward current derating (Ta ≥ 70°C)
Peak transient forward curent
(Note 1)
“H”peak output current (PW ≤ 2.5µs,f ≤ 15kHz)
(Note 2)
IOPH
−1.5
A
“L”peak output current (PW ≤ 2.5µs,f ≤ 15kHz)
(Note 2)
IOPL
+1.5
A
(Ta ≤ 70°C)
Detector
Output voltage
(Ta = 85°C)
(Ta ≤ 70°C)
Supply voltage
35
VO
24
35
VCC
(Ta = 85°C)
24
V
V
Output voltage derating (Ta ≥ 70°C)
∆VO / ∆Ta
−0.73
V / °C
Supply voltage derating (Ta ≥ 70°C)
∆VCC / ∆Ta
−0.73
V / °C
Tj
125
°C
f
25
kHz
Operating temperature range
Topr
−20~85
°C
Storage temperature range
Tstg
−55~125
°C
Junction temperature
Operating frequency
(Note 3)
Lead soldering temperature (10 s)
(Note 4)
Tsol
260
°C
Isolation voltage (AC, 1 min., R.H.≤ 60%)
(Note 5)
BVS
2500
Vrms
Note 1:
Pulse width PW ≤ 1µs, 300pps
Note 2:
Exporenential wavefom
Note 3:
Exporenential wavefom, IOPH ≤ −1.0A( ≤ 2.5µs), IOPL ≤ +1.0A( ≤ 2.5µs)
Note 4:
It is 2 mm or more from a lead root.
Note 5:
Device considerd a two terminal device: Pins 1, 2, 3 and 4 shorted together, and pins 5, 6, 7 and 8 shorted
together.
Note 6:
A ceramic capacitor(0.1µF) should be connected from pin 8 to pin 5 to stabilize the operation of the high
gain linear amplifier. Failure to provide the bypassing may impair the switching proparty. The total lead
length between capacitor and coupler should not exceed 1cm.
Recommended Operating Conditions
Characteristic
Input current, on
Input voltage, off
Supply voltage
Peak output current
Operating temperature
(Note 7)
Symbol
Min.
Typ.
Max.
Unit
IF(ON)
7
8
10
mA
VF(OFF)
0
―
0.8
V
VCC
15
―
IOPH/IOPL
―
―
Topr
−20
25
30
20
±0.5
70
V
A
85
°C
Note 7: Input signal rise time (fall time) < 0.5 µs.
2
2004-06-25
TLP250
Electrical Characteristics (Ta = −20~70°C, unless otherwise specified)
Symbol
Test
Cir−
cuit
VF
―
IF = 10 mA , Ta = 25°C
∆VF / ∆Ta
―
IF = 10 mA
Input reverse current
IR
―
VR = 5V, Ta = 25°C
Input capacitance
CT
―
V = 0 , f = 1MHz , Ta = 25°C
“H” level
IOPH
3
“L” level
IOPL
2
“H” level
VOH
“L” level
“H” level
Characteristic
Input forward voltage
Temperature coefficient of
forward voltage
Typ.*
Max.
Unit
1.6
1.8
V
−2.0
―
mV / °C
―
10
µA
―
45
250
pF
IF = 10 mA
V8−6 = 4V
−0.5
−1.5
―
IF = 0
V6−5 = 2.5V
0.5
2
―
4
VCC1 = +15V, VEE1 = −15V
RL = 200Ω, IF = 5mA
11
12.8
―
VOL
5
VCC1 = +15V, VEE1 = −15V
RL = 200Ω, VF = 0.8V
―
−14.2
−12.5
ICCH
―
VCC = 30V, IF = 10mA
Ta = 25°C
―
7
―
VCC = 30V, IF = 10mA
―
―
11
VCC = 30V, IF = 0mA
Ta = 25°C

7.5

VCC = 30V, IF = 0mA
―
―
11
―
1.2
5
mA
0.8
―
―
V
10
―
35
V
―
1.0
2.0
pF
―
Ω
Output current
Output voltage
Supply current
“L” level
ICCL
―
Test Condition
VCC = 30V
(*1)
―
Threshold input
current
“Output
L→H”
IFLH
―
VCC1 = +15V, VEE1 = −15V
RL = 200Ω, VO > 0V
Threshold input
voltage
“Output
H→L”
IFHL
―
VCC1 = +15V, VEE1 = −15V
RL = 200Ω, VO < 0V
VCC
―
Supply voltage
Capacitance
(input−output)
CS
―
VS = 0 , f = 1MHz
Ta = 25℃
Resistance(input−output)
RS
―
VS = 500V , Ta = 25°C
R.H.≤ 60%
* All typical values are at Ta = 25°C
Min.
A
V
12
1×10
14
10
mA
(*1): Duration of IO time ≤ 50µs
3
2004-06-25
TLP250
Switching Characteristics (Ta = −20~70°C , unless otherwise specified)
Characteristic
Propagation
delay time
Symbol
L→H
Test
Cir−
cuit
Test Condition
tpLH
H→L
tpHL
Output rise time
tr
Output fall time
tf
6
IF = 8mA (Note 7)
VCC1 = +15V, VEE1 = −15V
RL = 200Ω
Min.
Typ.*
Max.
―
0.15
0.5
―
0.15
0.5
―
―
―
―
―
―
Unit
µs
Common mode transient
immunity at high level
output
CMH
7
VCM = 600V, IF = 8mA
VCC = 30V, Ta = 25°C
−5000
―
―
V / µs
Common mode transient
immunity at low level
output
CML
7
VCM = 600V, IF = 0mA
VCC = 30V, Ta = 25°C
5000
―
―
V / µs
* All typical values are at Ta = 25°C
Note 7: Input signal rise time (fall time) < 0.5 µs.
4
2004-06-25
TLP250
Test Circuit 1 :
Test Circuit 2 : IOPL
8
1
1
8
0.1µF
VCC
A
4
IOPL
4
5
Test Circuit 3 : IOPH
V6-5
Test Circuit 4 : VOH
8
8
1
1
VCC1
VCC
0.1µF
0.1µF
V8-6
IF
IF
RL
A
V VOH
IOPH
4
4
VEE1
Test Circuit 5 : VOL
8
1
VCC1
0.1µF
VF
RL
V
VOL
4
VEE1
5
2004-06-25
TLP250
Test Circuit 6: tpLH, tpHL, tr tf
8
IF
IF
0.1µF
tr
tf
VCC1
VOH
VO
RL
VO
GND
VOL
tpLH
100Ω
80%
80%
tpHL
VEE1
Test Circuit 7: CMH, CML
8
1
SW IF
A
0.1µF
VCC
B
VO
4
VCM
+
-
600V
VCM
90%
10%
tf
tr
CML = 480 (V)
tr (µs)
SW :A(IF=8mA)
CMH = 480 (V)
tf (µs)
CMH
VO
3V
SW :B(IF=0)
26V
CHL
CML(CMH) is the maximum rate of rise (fall) of the common mode voltage that can be sustained with the output
voltage in the low (high) state.
6
2004-06-25
TLP250
IF – VF
Forward current IF
(mA)
50
30
ΔVF / ΔTa – IF
-2.6
Ta = 25 °C
Forward voltage temperature
coefficient ΔVF / ΔTa (mV / °C)
100
10
5
3
1
0.5
0.3
0.1
0.05
0.03
0.01
1.0
1.4
1.2
1.8
1.6
Forward voltage
VF
-2.4
-2.2
-2.0
-1.8
-1.6
-1.4
0.1
2.0
1
0.3 0.5
(V)
Forward current
IF – Ta
3
5
IF
(mA)
10
30
VCC – Ta
40
30
Allowable supply voltage VCC
Allowable forward current
IF (mA)
(V)
40
20
10
0
0
20
40
60
30
20
10
0
80
100
0
Ambient temperature Ta (°C)
20
40
60
80
100
Ambient temperature Ta (°C)
IOPH, IOPL – Ta
Allowable peak output current
IOPH, IOPL (A)
PW ≦ 2.5 µs, f ≦ 15 KHz
2
1
0
0
20
40
60
80
100
Ambient Temperature Ta (°C)
7
2004-06-25
TLP250
RESTRICTIONS ON PRODUCT USE
• The information contained herein is subject to change without notice.
• The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed
by TOSHIBA for any infringements of patents or other rights of the third parties which may result from its use. No license is
granted by implication or otherwise under any patent or patent rights of TOSHIBA or others.
• TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in
general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility
of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire
system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life,
bodily injury or damage to property.
In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the
most recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the
“Handling Guide for Semiconductor Devices,” or “TOSHIBA Semiconductor Reliability Handbook” etc..
• The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal
equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.). These TOSHIBA products
are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a
malfunction or failure of which may cause loss of human life or bodily injury (“Unintended Usage”). Unintended Usage include
atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments,
combustion control instruments, medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products
listed in this document shall be made at the customer’s own risk.
• The products described in this document are subject to the foreign exchange and foreign trade laws.
• TOSHIBA products should not be embedded to the downstream products which are prohibited to be produced and sold, under
any law and regulations.
• GaAs(Gallium Arsenide) is used in this product. The dust or vapor is harmful to the human body. Do not break, cut, crush or
dissolve chemically.
8
2004-06-25