AS8220A O bj e c t i v e D a ta S h e e t F l e x R a y TM B a s i s Tra n s c e i v e r 1 General Description 2 Key Features Data transfer up to 10 Mbps This objective data sheet describes the intended functionality of the AS8220A bus transceiver. As long the device is not fully qualified, the parameters are not characterized in the means that parameters may change or can be updated during final product qualification and characterization. This document shows the objective of the AS8220A and this document is subjected to change without notice. Compliant with FlexRay Electrical Physical Layer Specification V2.1 Rev. B Excellent EMC performances. High common mode range insure excellent EMI Enable pin for an optional bus guardian Automatic thermal shutdown protection The AS8220A is a high-speed automotive transceiver for fault tolerant and high speed applications, operating as the bi-directional interface between a generic communication controller and the twisted pair copper wires. The device enables two-way communication with the microcontroller with full mode handling, including the low-power modes. The transmission rates up to 10Mbps as well as the implemented Bus Guardian interface enables this transceiver the usage in fault tolerant and hard real-time applications in the stringent automotive environment. An extended diagnostic interface, offers advanced busfailure detection capabilities with the intelligent combination of bus-current measurement and logical comparators. A thermal sensor circuit with an integral shutdown mechanism prevents damage to the device in extreme temperature conditions. The symmetrical transient control for the high- and low-side driver for both the busminus and bus-plus line allows an ideal balance of communications over different network topologies, with excellent EMC performance. The product is available in SSOP14 package. Low standby current Supports 2.5, 3, 3.3, 5 V micro controllers and automatically adapts to interface levels Protection against damage due to short circuit conditions on the bus (positive and negative battery voltage) Operating temperature range -40ºC to +125ºC 3 Applications The device is ideal for high speed automotive bus systems, backbone bus and gateways, X-by-wire systems, redundant bus systems, bus topologies with Active Stars, and safety critical applications. Designed for FlexRay, where the basic features are demanded. Figure 1. Block Diagram AS8220A VIO STBN ERRN VIO RxD TxD TxEN BGE Bus Failure Detector Host Controller Interface Communication Controller Interface Transmitter Digital Logic Bus Guardian Interface BP BM Receiver www.austriamicrosystems.com Revision 17920-001-10a GND VIO VCC Power Supply Interface 1 - 33 AS8220A Objective Data Sheet - Applications Contents 1 General Description ............................................................................................................................... 1 2 Key Features ...........................................................................................................................................1 3 Applications ............................................................................................................................................ 1 4 Pin Assignments .................................................................................................................................... 4 4.1 Pin Descriptions ................................................................................................................................................4 5 Absolute Maximum Ratings .................................................................................................................. 5 6 Electrical Characteristics....................................................................................................................... 6 7 Typical Operating Characteristics ...................................................................................................... 11 8 Detailed Description ............................................................................................................................. 12 8.1 Block Description.............................................................................................................................................12 8.2 Events..............................................................................................................................................................12 8.3 Operating Modes .............................................................................................................................................12 8.3.1 NORMAL mode .....................................................................................................................................13 8.3.2 STANDBY mode ...................................................................................................................................13 8.4 Non Operating Mode .......................................................................................................................................13 8.4.1 Power Off .............................................................................................................................................13 8.5 Undervoltage Events .......................................................................................................................................13 8.5.1 Undervoltage VIO...................................................................................................................................13 8.5.2 Undervoltage VCC .................................................................................................................................13 8.6 Power On/Off Events.......................................................................................................................................14 8.7 System Description .........................................................................................................................................14 8.8 Fail Silent Behavior .........................................................................................................................................15 8.8.1 State transitions due to under voltage detection ...................................................................................15 8.8.2 State transitions due to voltage recovery detection ..............................................................................15 8.9 Mode Transitions .............................................................................................................................................15 8.9.1 ERRN Signalling ...................................................................................................................................16 8.10 Loss of ground...............................................................................................................................................16 8.11 Error Flags Description ..................................................................................................................................16 8.11.1 Bus error .............................................................................................................................................16 8.11.2 Low current on BP high side driver .....................................................................................................16 8.11.3 Low current on BP low side driver.......................................................................................................16 8.11.4 Low current on BM high side driver.....................................................................................................16 8.11.5 Low current on BM low side driver ......................................................................................................16 8.11.6 High current on BP high side driver ....................................................................................................16 8.11.7 High current on BP low side driver ......................................................................................................16 8.11.8 High current on BM high side driver ....................................................................................................17 8.11.9 High current on BM low side driver .....................................................................................................17 8.11.10 BP open line ......................................................................................................................................17 8.11.11 BM open line .....................................................................................................................................17 8.11.12 BP short circuit to VCC .......................................................................................................................17 8.11.13 BP short circuit to GND .....................................................................................................................17 8.11.14 BM short circuit toVCC .......................................................................................................................17 8.11.15 BM short circuit to GND ....................................................................................................................17 8.11.16 Short circuit between BP and BM .....................................................................................................17 8.11.17 Over temperature ..............................................................................................................................17 www.austriamicrosystems.com Revision 17920-001-10a 2 - 33 AS8220A Objective Data Sheet - Applications 8.11.18 TxEN_BGE timeout ...........................................................................................................................17 8.11.19 Error flag ...........................................................................................................................................17 8.12 Status Flags Description................................................................................................................................17 8.12.1 Power on flag ......................................................................................................................................17 8.13 Transmitter ....................................................................................................................................................18 8.14 Receiver ........................................................................................................................................................20 8.14.1 8.14.2 8.14.3 8.14.4 Bus activity and idle detection (only in NORMAL mode).....................................................................20 Bus data detection (NORMAL mode)..................................................................................................20 Receiver test signal .............................................................................................................................22 Transceiver Timing..............................................................................................................................23 8.15 Test Circuits ...................................................................................................................................................24 9 Appendix ............................................................................................................................................... 25 10 Package Drawings and Markings...................................................................................................... 31 11 Ordering Information.......................................................................................................................... 32 www.austriamicrosystems.com Revision 17920-001-10a 3 - 33 AS8220A Objective Data Sheet - Pin Assignments 4 Pin Assignments Figure 2. Pin Assignments SSOP14 Package VIO 1 14 VCC TxD 2 13 BP TxEN 3 12 BM RxD 4 11 GND BGE 5 10 ERRN STBN 6 9 7 8 AS8220A Pin Descriptions Table 1. Pin Descriptions Pin Name VIO TxD TxEN RxD BGE STBN ERRN GND BM BP VCC www.austriamicrosystems.com Pin Number 1 2 3 4 5 6 10 11 12 13 14 Description I/O supply voltage Transmit data input Transmitter enable input Receive data output Bus guardian enable input Standby input Error diagnosis output Ground Bus line Minus Bus line Plus Supply Voltage Revision 17920-001-10a 4 - 33 AS8220A Objective Data Sheet - Absolute Maximum Ratings 5 Absolute Maximum Ratings Stresses beyond those listed in Table 2 may cause permanent damage to the device. These are stress ratings only. Functional operation of the device at these or any other conditions beyond those indicated in Section 6 Electrical Characteristics on page 6 is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Table 2. Absolute Maximum Ratings Parameter Min Max Units Supply Voltage (VCC) -0.3 +7.0 V Supply Voltage (VIO) -0.3 +7.0 V DC Voltage at EN, STBN, ERRN, TxD, RxD, TxEN, BGE, RxEN -0.3 VIO + 0.3 V DC Voltage at BP and BM -40 +50 V Input current (latchup immunity) -100 100 mA According to JEDEC 78 Electrostatic discharge at bus lines BP and BM -4 +4 kV According to AEC-Q100-002 Electrostatic discharge -2 +2 kV According to AEC-Q100-002 Transient voltage on BP, BM -200 +200 V According to ISO7637 part3 test pulses a and b; class C; RL=45 W, CL= 100 pF; (see Figure 17 on page 24). 150 mW Total power dissipation (all supplies and outputs) Storage temperature -55 +150 ºC Junction temperature -40 +150 ºC 250 ºC 85 % 1 Package body temperature Humidity non-condensing 5 Notes VIO < VCC 1. The reflow peak soldering temperature (body temperature) specified is in accordance with IPC/JEDEC J-STD020C “Moisture/Reflow Sensitivity Classification for Non-Hermetic Solid State Surface Mount Devices”. The lead finish for Pb-free leaded packages is matte tin (100% Sn). www.austriamicrosystems.com Revision 17920-001-10a 5 - 33 AS8220A Objective Data Sheet - Electrical Characteristics 6 Electrical Characteristics Tvj = -40 to +150 ºC, VCC = +4.75V to +5.25V, VIO = +2.2 to VCC, RL= 45Ω, CL= 100 pF unless otherwise specified. Table 3. Electrical Characteristics Symbol Parameter Conditions Min Typ Max Units Supply Voltage Tamb Ambient temperature -40 +125 ºC VCC-VIO Difference of supplies -0.1 3.05 V STANDBY Mode VCC = 0V to +5.25V -5 30 µA NORMAL mode, driver enabled 0 45 mA NORMAL Mode, driver enabled, RBUS = ∞Ω 0 15 mA NORMAL mode, driver disabled 0 10 mA STANDBY mode VIO = 0V to +5.25V -5 5 µA NORMAL Mode 0 1 mA 1 50 µs 1 ICC VCC current consumption 1 IIO VIO current consumption State Transitions tSTBN_RxD Delay STBN high to RxD high with wake flag set tSTANDBY go-to STANDBY hold time INH1 low = 20% VBAT 10 70 µs VBUS_DIFF_D0 Differential bus voltage low in NORMAL mode (Data0) VBPdata0 - VBMdata0; 40Ω < RL < 55Ω -2 -0.6 V VBUS_DIFF_D1 Differential bus voltage high in NORMAL mode (Data1) VBPdata1 - VBMdata1; 40Ω < RL < 55Ω 0.6 2 V ΔVBUS_DIFF Matching between Data0 and Data1 differential bus voltage in NORMAL mode VBUS_DIFF_D0 - VBUS_DIFF_D1 40Ω < RL < 55Ω -200 200 mV VBUS_COM_D0 Common mode bus voltage in case of Data0 in NORMAL mode VBPdata0/2 + VBMdata0/2 40Ω < RL < 55Ω 0.4 * VCC 0.6 * VCC V VBUS_COM_D1 Common mode bus voltage in case of Data1 in NORMAL mode VBPdata1/2 + VBMdata1/2 40Ω < RL < 55Ω 0.4 * VCC 0.6 * VCC V -200 200 mV 30 mV Transmitter ΔVBUS_COM Matching between Data0 V BUS_COM_D0 - VBUS_COM_D1 and Data1 common mode 40Ω < RL < 55Ω voltage VBUS_DIFF_Idle Absolute differential bus voltage in idle mode IBPBMShortMax IBMBPShortMax Absolute max current when BP is shorted to BM VBP=VBM +100 mA IBPGNDShortMax Absolute max current when BP is shorted to GND VBP= 0V +100 mA IBMGNDShortMax Absolute max current when BM is shorted to GND VBM= 0V +100 mA www.austriamicrosystems.com Revision 17920-001-10a 6 - 33 AS8220A Objective Data Sheet - Electrical Characteristics Table 3. Electrical Characteristics Symbol Parameter Conditions IBP-5VShortMax Absolute max current when BP is shorted to -5 V IBM-5VShortMax Min Typ Max Units VBP= -5V +100 mA Absolute max current when BM is shorted to -5 V VBM= -5V +100 mA IBP27VShortMax Absolute max current when BP is shorted to 27 V VBP= 27V +100 mA IBM27VShortMax Absolute max current when BM is shorted to 27 V VBM= 27V +100 mA IBP48VShortMax Absolute max current when BP is shorted to 48 V VBP= 48V +100 mA IBM48VShortMax Absolute max current when BM is shorted to 48 V VBM= 48V +100 mA tTxD_BUS01 Delay time from TxD to BUS positive edge tTxD_RISE = 5ns 50 ns tTxD_BUS10 Delay time from TxD to BUS negative edge tTxD_FALL = 5ns 50 ns tTxD_MISMATCH Delay time from TxD to BUS mismatch tTxD_BUS10 - tTxD_BUS01 -4 4 ns tBUS10 Fall time differential bus voltage 80% - 20% of VBUS 3.75 18.75 ns tBUS01 Rise time differential bus voltage 20% - 80% of VBUS 3.75 18.75 ns tTxEN_BUS_Idle_Active Delay time from TxEN to bus active 50 ns tTxEN_BUS_Active_Idle Delay time from TxEN to bus idle 50 ns tTxEN_MISMATCH Delay time from TxEN to bus mismatch 50 ns tBGE_BUS_Idle_Active Delay time from BGE to bus active 50 ns tBGE_BUS_Active_Idle Delay time from BGE to bus idle 50 ns tBUS_Idle_Active Differential bus voltage transition time: idle to active 30 ns tBUS_Active_Idle Differential bus voltage transition time: active to idle 30 ns tTxEN_timeout TxEN timeout 0.64 3.07 ms |tTxEN_BUS_Idle_Active tTxEN_BUS_Active_Idle| Receiver RBP, RBM BP, BM input resistance Idle mode; RBUS=∞ 10 40 KΩ RDIFF BP, BM differential input resistance Idle mode; RBUS=∞ 20 80 KΩ VBPidle, VBMidle Idle voltage in NORMAL mode on pin BP, BM NORMAL mode; VTxEN = VIO 0.4* VCC 0.5* VCC 0.6* VCC V VBPidle_low, VBMidle_low Idle voltage in STANDBY mode on pin BP, BM STANDBY mode -0.2 0 +0.2 V www.austriamicrosystems.com Revision 17920-001-10a 7 - 33 AS8220A Objective Data Sheet - Electrical Characteristics Table 3. Electrical Characteristics Symbol Parameter Conditions Min IBPidle Absolute idle output current on pin BP -40V < VBP < 50V IBMidle Absolute idle output current on pin BM IBPleak, IBMleak Max Units 0 7.5 mA -40V < VBM < 50V 0 7.5 mA Absolute leakage current, when not powered VBP = VBM = 5V, VCC = 0V, VBAT = 0V; VIO = 0V 0 +10 uA VBUSActiveHigh Activity detection differential input voltage high NORMAL mode -10V < (VBP , VBM) < 15V 150 225 400 mV VBUSActiveLow Activity detection differential input voltage low NORMAL mode -10V < (VBP , VBM)< 15V -400 -225 -150 mV VData1 Data1 detection differential input voltage Pre-condition: activity already detected. NORMAL mode. -10V < (VBP , VBM)< 15V 150 225 300 mV VData0 Data0 detection differential input voltage Pre-condition: activity already detected. NORMAL mode. -10V < (VBP , VBM)< 15V -300 -225 -150 mV VDataErr Mismatch between Data0 and Data1 differential input voltage 10 % tBUS_RxD10 Delay from BUS to RxD negative edge CRxD = 15 pF 3 80 ns tBUS_RxD01 Delay from BUS to RxD positive edge CRxD = 15 pF 3 80 ns tBIT Bit time CRxD = 15 pF 3 tRxD_ASYM Delay time from BUS to RxD mismatch tRxD_FALL Fall time RxD voltage tRxD_RISE Rise time RxD voltage tBUSIdleDetection Idle detection time VBUS: 400mV → 0V tBUSActivitiyDetection Activity detection time tBUSIdleReaction tBUSActivityReaction 2 x (⎜⎜VData0⎜- ⎜VData1⎜⎜) / (⎜VData0⎜+⎜VData1⎜) 2 Typ 54 CRXD=15 pF; ns 5 ns 5 ns 5 ns 50 200 ns VBUS: 0V → 400mV 100 250 ns Idle reaction time VBUS: 400mV → 0V 50 300 ns Activity reaction time VBUS: 0V → 400mV 100 350 ns |tBUS_RxD10- tBUS_RxD01| 3 80% - 20% of VRxD; CRxD=15 pF 3 20% - 80% of VRxD; CRxD=15 pF 3 Supply Voltage Monitor VCCTHH VCC under-voltage recovery threshold 3.5 4.5 V VCCTHL VCC undervoltage detection threshold 2.5 3.5 V VIOTHH VIO undervoltage recovery threshold 1.25 2.0 V VIOTHL VIO undervoltage detection threshold 0.75 1.5 V www.austriamicrosystems.com Revision 17920-001-10a 8 - 33 AS8220A Objective Data Sheet - Electrical Characteristics Table 3. Electrical Characteristics Symbol Parameter Conditions tUV_DETECT Detection time for undervoltage at VBAT, VCC, VIO tUV_REC Detection time for undervoltage recovery at VCC, VIO Min Typ Max Units 100 700 ms 0.7 5 ms Bus Error Detection ITHL Absolute bus current for low current detection NORMAL mode, Transmitter enabled 5 mA ITHH Absolute bus current for high current detection NORMAL mode, Transmitter enabled 40 mA VSHORT Differential voltage on BP and BM for detecting short circuit between bus lines NORMAL mode, Transmitter enabled 225 mV tBUS_ERROR Bus error detection time NORMAL mode, Transmitter enabled 20 µs Over Temperature OTTH Over temperature threshold 150 180 ºC OTTL Over temperature hysteresis 10 20 ºC 0.7* VIO V Communication Controller Interface VTxDIH Threshold for detecting TxD as on logical high VTxDIL Threshold for detecting TxD as on logical low 0.3* VIO ITxDIH TxD high level input current 30 100 µA ITxDIL TxD low level input current -5 5 µA VTxENIH Threshold for detecting TxEN as on logical high 0.7* VIO V VTXENIL Threshold for detecting TxEN as on logical low 0.3* VIO ITxENIH TxEN high level input current -5 5 µA ITxENIL TxEN low level input current -100 -30 µA VRxDOH RxD high level output voltage IRxD = -4mA, VIO = 5V 0.8* VIO 1.0* VIO V VRxDOL RxD low level output voltage IRxD = 4mA, VIO = 5V 0 0.2* VIO V 0.7* VIO V V V Host Interface VSTBNIH Threshold for detecting STBN as on logical high VSTBNIL Threshold for detecting STBN as on logical low 0.3* VIO ISTBNIH STBN high level input current 30 www.austriamicrosystems.com Revision 17920-001-10a V 100 µA 9 - 33 AS8220A Objective Data Sheet - Electrical Characteristics Table 3. Electrical Characteristics Symbol Parameter Conditions ISTBNIL STBN low level input current tSTBN_DEB_STBY Min Typ Max Units -5 5 µA STBN de-bouncing time STANDBY mode 0.1 40 µs tSTBN_DEB_NORM STBN de-bouncing time NORMAL mode 0.1 2 µs VERRNOH ERRN high level output voltage IERRN = -4mA, VIO = 5V 0.8* VIO 1.0* VIO V VERRNOL ERRN low level output voltage IERRN = 4mA, VIO = 5V 0 0.2* VIO V 0.7* VIO V Bus Guardian Interface VBGEIH Threshold for detecting BGE as on logical high VBGEIL Threshold for detecting BGE as on logical low 0.3* VIO IBGEIH BGE high level input current 30 100 µA IBGEIL BGE low level input current -5 5 µA V 1. STBN, ERRN, TxD, RxD, TxEN, and BGE open 2. Test condition: (VBP + VBM) / 2 = 2,5V ± 5% 3. For test signal (see Figure 15) www.austriamicrosystems.com Revision 17920-001-10a 10 - 33 AS8220A Objective Data Sheet - Ty p i c a l O p e r a t i n g C h a r a c t e r i s t i c s 7 Typical Operating Characteristics Figure 3. Figure 4. Figure 5. Figure 6. Figure 7. Figure 8. www.austriamicrosystems.com Revision 17920-001-10a 11 - 33 AS8220A Objective Data Sheet - Detailed Description 8 Detailed Description The AS8220A is a high-speed fault tolerant device operating as an interface between a generic controller and the copper wire physical bus. The AS8220A is designed to extend the application range for high speed and safety critical time triggered bus systems in an automotive environment. The drivers are short circuit protected against the positive and negative supply voltage to increase the robustness and reliability of automotive systems. The AS8220A operates at baudrates up to 10 Mbps to increase the bandwidth for automotive applications. Block Description The electrical AS8220A high-speed bus-system transceiver is the interface between a FlexRay™ network node module and the channel. The transceiver provides differential transmit and receive capability to the bus, allowing the node module bidirectional time multiplexed binary data stream transfer. Besides the transmit and receive function, the transceiver provides low power management, supply voltage monitoring (under voltage detection) as well as bus failure detection and represents a ESD-protection barrier between the bus and the ECU. The AS8220A consists of 8 different functional blocks (see Figure 1): Table 4. Functional Blocks Functional Block Host Controller Interface (HCI) Short Description Digital interface between the transceiver and the host controller (HC) The host interface comprises the read out handler, which delivers failure and status information via the ERRN pin to the host controller. Communication Controller Interface Digital interface between the transceiver and the FlexRay communication (CCI) controller (CC) Bus Guarding Interface (BGI) Power Supply Interface (PSI) Digital interface between the transceiver and the FlexRay bus guardian (BG) The power supply interface consists of an sub functional block, the voltage monitor (VM) and includes two analogue inhibit outputs for signalling the internal state of the transceiver Internal Logic (IL) The digital signals from the functional blocks of the device are fed into the internal logic where the forwarding of FlexRay messages from analogue side to digital interfaces and vice versa is done. The state machine is performed in this block and is dealing the error, wake and power-on flags. Bus Failure Detector (BFD) Temperature Protection (TP) The bus failure detector is directly connected to the bus pins, in order to detect several external failure conditions which may occur on the bus. The temperature protection turns off the output driver when reaching the specified internal temperature in order to protect the device. Transmitter Receiver The transmitter provides the bus signals as specified on the bus lines. The receiver captures FlexRay valid signals on the bus lines and provides received data streams to the internal logic Events Transitions in order to change between the operation modes are possible only when events are detected. The device supports two type of events, events on the host controller interface (STBN) and detection of undervoltage or supply voltage recovery. Whenever an event is recognized, a transition can be performed. Operating Modes The AS8220A provides the following operating modes: NORMAL: non low power mode STANDBY: low power mode www.austriamicrosystems.com Revision 17920-001-10a 12 - 33 AS8220A Objective Data Sheet - Detailed Description NORMAL mode In this mode the transceiver is able to send and receive data signals on the bus. TxEN and BGE control the state of the transmitter. RxD reflects the bus data and reflect the bus state. In this mode, the transmitter state can be selected as shown in the Table 5. In case the over-temperature flag is set the transmitter is disabled. The bus wires are terminated to VCC/2 via receiver input resistances. Table 5. Transmitter State BGE TxEN TxD Transmitter state Bus State H L H Enabled Data1 (BP is driven high, BM is driven low) H L L Enabled Data0 (BP is driven low, BM is driven High) X H X Disabled Idle (BP and BM are not driven) L X X Disabled Idle (BP and BM are not driven) If the differential bus voltage is higher than VBUSActivehigh or lower than VBUSActivelow for a time longer than tBUSActhen activity is detected on the bus (Bus = active), RxD is released. tivityDetection, If, after the activity detection, the differential bus voltage is higher than VData1, RxD is high. If, after the activity detection, the differential bus voltage is lover than VData0, RxD is low. If the absolute differential bus voltage is lower than VBUSActivehigh and higher than VBUSActivelow for a time longer than tBUSIdleDetection, then idle is detected on the bus (Bus=idle), RxD is switched to logical “high” STANDBY mode In this mode the transceiver is not able to send and receive data signals from the bus. The power consumption is significantly reduced respect the NORMAL mode. The bus wires are terminated to GND (bus state: Idle_LP). Non Operating Mode The AS8220A provides the following non operating mode: Power Off In this mode the transceiver is not able to operate. RxD is set to high and ERRN is set to low. The bus wires are not connected to GND (bus state: Idle_HZ). Undervoltage Events Undervoltage VIO When VIO voltage falls below VIOTHL for a time longer than tUV_DETECT then the undervoltage VIO flag is set and it is reset when VIO exceeds the voltage threshold VIOTHH for a time longer than tUV_REC. The flag can be set or reset in all the operation modes. The flag is reset at power off. Undervoltage VCC When VCC voltage falls below VCCTHL for a time longer than tUV_DETECT then the undervoltage VCC flag is set and it is reset when VCC exceeds the voltage threshold VCCTHH for a time longer than tUV_REC. The flag can be set or reset in all the operation modes. The flag is reset at power off. www.austriamicrosystems.com Revision 17920-001-10a 13 - 33 AS8220A Objective Data Sheet - Detailed Description Power On/Off Events Starting from power off mode a power on event occurs in case undervoltage flag is reset. Starting from every operation mode a power off event occurs in case VCC undervoltage flag is set. System Description Figure 9. State Diagram Normal VREC_VCC UV_VIO OR STBN=0 Power Off VREC_VIO WHILE (STBN=1) OR STBN=1 UV Input: STBN = 1 C _V C UV_VCC UV_VCC Standby Input: STBN = 0 VREC_VIO WHILE (STBN=0) Note: In Table 7 the corresponding transition table is shown Prefix of “WHILE” is always the event and suffix in brackets checks the flags or in case of STBN the input condition. For example: VREC_VBAT WHILE (STBN=1) After the event VIO supply voltage recovery is detected, the transition is performed if STBN is “high”. Legend: UV_VIO: Undervoltage event and/or flag for VIO supply voltage UV_VCC: Undervoltage event and/or flag for VCC supply voltage VREC_VIO: Voltage recovery event and/or flag for VIO supply voltage VREC_VCC: Voltage recovery event and/or flag for VCC supply voltage www.austriamicrosystems.com Revision 17920-001-10a 14 - 33 AS8220A Objective Data Sheet - Detailed Description Fail Silent Behavior In order to be fail silent, undervoltage detection on the two power supplies VIO and VCC is implemented VIO: Supply voltage for I/O digital level adaptation VCC: Supply voltage (+5V) State transitions due to under voltage detection In case of VIO undervoltage is detected, STANDBY mode will be entered regardless of the voltage present on pin STBN. In case VCC undervoltage is present, the device will enter power off mode (bus state: Idle_HZ), regardless on supply voltage at VIO and the voltage present on STBN. State transitions due to voltage recovery detection Starting from the power off, the device enters STANDBY mode only in case VCC undervoltage flag is reset.. When VCC ≤ VCCTHL the device is in power off state and the bus wires are not terminated (bus state: Idle_HZ). Mode Transitions In case all the undervoltage flags are reset the operation mode is selected by STBN according to Table 6. Table 6. Pin Signalling and Operating modes Inputs OutPut Operation Mode STBN H NORMAL L STANDBY RxD RxEN L Bus = Data_0 L Bus = Active H Bus = Idle or Data_1 H Bus = Idle H H Where: H = Digital level high L = Digital level low x = Do not care Float = The analog output is not driven Table 7. Transition Table Supply Voltage Flag Event Intial Mode Host Event VIO VCC STBN L L H→L L→H L X H→L L H L L L→H Power Off X H→L X Standby Any X L→H X Power Off Normal Standby www.austriamicrosystems.com Revision 17920-001-10a Next Mode Standby Normal 15 - 33 AS8220A Objective Data Sheet - Detailed Description ERRN Signalling The ERRN signalling is shown in Table 8. Table 8. ERRN signalling HOST COMMAND SUPPLY VOLTAGE FLAG EVENT VIO STBN ERRN L H not failure L L H L X L Note: ERROR means the logic OR of the error flags Loss of ground In case the ground of the device is disconnected and the host pins are open, the bus lines are switched to Idle_HZ. Error Flags Description Bus error The bus error flag is set when 2 consecutive rising edges on the TxD pin without any rising edge on the RxD pin are detected or when 2 consecutive falling edges on the TxD pin without any falling edge on the RxD pin are detected. This flag is reset when a rising edge on the TxD pin is followed by a rising edge on RxD pin before of the next TxD rising edge or when a falling edge on the TxD pin is followed by a falling edge on RxD pin before of the next TxD falling edge. This flag can be set or reset only in NORMAL mode when the transmitter is enabled. The flag is reset at power off. Low current on BP high side driver This flag can only be set/reset in NORMAL mode when the driver is enabled and during the transmission of a stable Data1 longer than tBUS_ERROR. If the absolute value of the BP pin current is lower than ITHL after tBUS_ERROR since the driver enable signal then the flag is set otherwise it is reset. The flag is reset at power off. Low current on BP low side driver This flag can only be set/reset in NORMAL mode when the driver is enabled and during the transmission of a stable Data0 longer than tBUS_ERROR. If the absolute value of the BP pin current is lower than ITHL after tBUS_ERROR since the driver enable signal then the flag is set otherwise it is reset. The flag is reset at power off. Low current on BM high side driver This flag can only be set/reset in NORMAL mode when the driver is enabled and during the transmission of a stable Data0 longer than tBUS_ERROR. If the absolute value of the BM pin current is lower than ITHL after tBUS_ERROR since the driver enable signal then the flag is set otherwise it is reset. The flag is reset at power off. Low current on BM low side driver This flag can only be set/reset in NORMAL mode when the driver is enabled and during the transmission of a stable Data1 longer than tBUS_ERROR. If the absolute value of the BM pin current is lower than ITHL after tBUS_ERROR since the driver enable signal then the flag is set otherwise it is reset. The flag is reset at power off. High current on BP high side driver This flag can only be set/reset in NORMAL mode when the driver is enabled and during the transmission of a stable Data1 longer than tBUS_ERROR. If the absolute value of the BP pin current is higher than ITHH after tBUS_ERROR since the driver enable signal then the flag is set otherwise it is reset. The flag is reset at power off. High current on BP low side driver This flag can only be set/reset in NORMAL mode when the driver is enabled and during the transmission of a stable Data0 longer than tBUS_ERROR. If the absolute value of the BP pin current is higher than ITHH after tBUS_ERROR since the driver enable signal then the flag is set otherwise it is reset. The flag is reset at power off. www.austriamicrosystems.com Revision 17920-001-10a 16 - 33 AS8220A Objective Data Sheet - Detailed Description High current on BM high side driver This flag can only be set/reset in NORMAL mode when the driver is enabled and during the transmission of a stable Data0 longer than tBUS_ERROR. If the absolute value of the BM pin current is higher than ITHH after tBUS_ERROR since the driver enable signal then the flag is set otherwise it is reset. The flag is reset at power off. High current on BM low side driver This flag can only be set/reset in NORMAL mode when the driver is enabled and during the transmission of a stable Data1 longer than tBUS_ERROR. If the absolute value of the BM pin current is higher than ITHH after tBUS_ERROR since the driver enable signal then the flag is set otherwise it is reset. The flag is reset at power off. BP open line This flag is the logical “AND” between: low current on BP high side and low current on BP low side. BM open line This flag is the logical “AND” between: low current on BM high side and low current on BM low side. BP short circuit to VCC This flag is the logical “AND” between: low current on BP high side and high current on BP low side. BP short circuit to GND This flag is the logical “AND” between: high current on BP high side and low current on BP low side. BM short circuit toVCC This flag is the logical “AND” between: low current on BM high side and high current on BM low side. BM short circuit to GND This flag is the logical “AND” between: high current on BM high side and low current on BM low side. Short circuit between BP and BM This flag can only be set or reset in NORMAL mode when the driver is enabled. After a time tBUS_ERROR since TxD edge if the absolute value of the differential bus voltage is lower than VSHORT then the flag is set otherwise it is reset. he flag is reset at power off. Over temperature This flag can only be set or reset in the non low power modes. The flag is set when the junction temperature exceeds OTTH and it is reset when the junction temperature falls below OTTL. TxEN_BGE timeout This flag can only be set in NORMAL mode when the driver is enabled (TxEN is low and BGE is high) for a time longer than tTxEN_max. It is reset every transition on TxEN or BGE or if the device exits NORMAL mode. If the flag is set the driver is disabled. Error flag This flag is set if at least one error flag or if VIO flag is set and it is reset if none of the previous flag is set. Status Flags Description Power on flag The power on flag is set leaving the power off state and it is reset entering a low power mode after a non low power mode. www.austriamicrosystems.com Revision 17920-001-10a 17 - 33 AS8220A Objective Data Sheet - Detailed Description Transmitter The transmitter generates out of a digital input signal on TxD the FlexRay differential bus voltage. The transmitter is only active in NORMAL mode when BGE is on logical high and TxEN is on logical low. Figure 10. Transmitter characteristics (TxD → BUS) VTxD 70% * VIO 30% * VIO Data1: x * tBIT Data0: x * tBIT VBUS tTxD_BUS01 tTxD_BUS10 tBUS01 tBUS01 VBUS_DIFF_D1 80% * VBUS_DIFF + VBUS_DIFF_Idle - VBUS_DIFF_Idle 20% * VBUS_DIFF VBUS_DIFF_D0 Data1: x * tBIT Data0: x * tBIT Figure 11. Transmitter characteristics (TxEN → BUS) VTxEN 70% * VIO 30% * VIO < tTxEN_timeout < tTxEN_timeout VBUS tTxEN_BUS_Active_Idle tTxEN_BUS_Idle_Active tBUS_Active_Idle tBUS_Idle_Active VBUS_DIFF_D1 300 mV + VBUS_DIFF_Idle - VBUS_DIFF_Idle - 300 mV VBUS_DIFF_D0 www.austriamicrosystems.com Revision 17920-001-10a 18 - 33 AS8220A Objective Data Sheet - Detailed Description Figure 12. Timing characteristics (BGE → BUS) VBGE 70% * VIO 30% * VIO < tTxEN_timeout < tTxEN_timeout VBUS tBGE_BUS_Active_Idle tBGE_BUS_Idle_Active tBUS_Active_Idle tBUS_Idle_Active VBUS_DIFF_D1 300 mV + VBUS_DIFF_Idle - VBUS_DIFF_Idle - 300 mV VBUS_DIFF_D0 In NORMAL mode the transmitter drives on the bus Idle in case no data are transmitted. In STANDBY mode the transmitter drives Idle_LP (idle low power) on the bus pins. In POWER OFF mode the bus pins shows Idle_HZ (idle high impedance). www.austriamicrosystems.com Revision 17920-001-10a 19 - 33 AS8220A Objective Data Sheet - Detailed Description Receiver The receiver generates from the FlexRay differential bus voltage a digital signal on the RxD pin. RxD shows the data (Data0 and Data1). The receiver is only active in NORMAL mode. Figure 13. Timing characteristics of the bus signals to RxD VBUS VBUS_ ActiveHigh VData1 +VBUS_DIFF_Idle - VBUS_DIFF_Idle VBUS_ ActiveLow VData0 VRxD Data0: x * tBIT Data1: x *tBIT tBUS_RxD10 tBUS_RxD01 tRxD_FALL tRxD_RISE 70% *VIO 30% *VIO Bus activity and idle detection (only in NORMAL mode) If the absolute differential bus voltage is higher than VBUSActiveLow and less than VBUSActiveHigh for a time longer than tBUSIdleDetection, bus Idle is detected, RxD is switched to logical high after a time tBUSIdleReaction. If the absolute differential bus voltage is higher than VBUSActiveHigh or lower than VBUSActiveLow for a time loner than tBUSActivitiyDetection, bus Activity is detected, RxD is following the detected bus data states as indicated below with a time tBUSActivityReaction. Table 9. Logic table for receiver bus signal detection Receiver Operation mode NORMAL mode Bus signals RxD Idle H Data0 L Data1 H Bus data detection (NORMAL mode) If, after the activity detection the differential bus voltage is higher than VData1, RxD will be high after a time tBUS_RxD01. If, after the activity detection the differential bus voltage is lower than VData0, RxD will be low after a time tBUS_RxD10. www.austriamicrosystems.com Revision 17920-001-10a 20 - 33 AS8220A Objective Data Sheet - Detailed Description Figure 14. Receiver characteristics (BUS → RxD, ) VRxD VBUS VBUS VBUS_ ActiveLow VData0 Data0 Activity www.austriamicrosystems.com VBUS_ ActiveHigh VData1 Idle Revision 17920-001-10a Data1 Activity 21 - 33 AS8220A Objective Data Sheet - Detailed Description Receiver test signal Figure 15. Receiver test signal V BUS 22 ns 22 ns 400 mV 300 mV -300 mV -400 mV tBIT tBUS_RxD01 RxD V BUS tBUS_RxD10 22 ns 22 ns 400 mV 300 mV -300 mV -400 mV tBIT RxD www.austriamicrosystems.com tBUS_RxD10 Revision 17920-001-10a tBUS_RxD01 22 - 33 www.austriamicrosystems.com Revision 17920-001-10a RxD VBUS TxEN BGE TxD 0.3 * VIO 0.7 * VIO 300 mV 0.3 * Vcc 0.7 * Vcc 0.3 * Vcc 0.7 * Vcc tTxD_BUS01 tBUS_RxD01 tTxD_BUS10 tBUS_RxD10 -300 mV 30 mV tBUSIdleReaction tBGE_BUS_Active_Idle tBUS_Idle_Active tBUSActivityReaction -300 mV tBGE_BUS_Idle_Active tBUS_Active_Idle 30 mV tTxEN_BUS_Active_Idle tTxEN_BUS_Idle_Active -300 mV tBUS01 tBUS10 20 % 80 % AS8220A Objective Data Sheet - Detailed Description Transceiver Timing Figure 16. Timing Diagram 23 - 33 AS8220A Objective Data Sheet - Detailed Description Test Circuits Figure 17. Test Circuit for Automotive Transients +5V Transients in accordance with ISO: 7637 test pulses 1, 2, 3a, 3b, 4, 5 Test conditions : Normal mode bus idle Normal mode bus active(TXD=5 MHz, TXEN=1kHz) 100nF 14 VCC 1 VIO 4 RXD 15pF AS8220 1nF 13 BP ISO7637 PULSE GENERATOR 12 BM RL CL 1nF Figure 18. Test circuit for dynamic characteristics +5V 100nF 14 VCC 1 VIO RXD 15pF AS 8220 BP BM www.austriamicrosystems.com 4 Revision 17920-001-10a 13 12 RL CL 24 - 33 AS8220A Objective Data Sheet - Appendix 9 Appendix The following table shows the comparison of conventions used in AS8220A datasheet and FlexRay Electrical Physical Layer Specification V2.1 Rev. B. Table 10. Comparison table FlexRay Electrical Physical Layer Specification V2.1 RevB AS8220A Datasheet Symbol Parameter Name Description - Battery Supply Voltage (VBAT) - - - Supply Voltage (VCC) - - - Supply Voltage (VIO) - - - DC Voltage at EN, STBN, ERRN, TxD, RxD, TxEN, BGE, RxEN - - - DC Voltage on pin WAKE, INH1, INH2 - - - DC Voltage at BP and BM - - - Input current (latchup immunity) - - - Electrostatic discharge at bus lines BP, BM, VBAT, WAKE uESDExt ESD protection on pins that lead to ECU external terminals - Electrostatic discharge uESDint ESD on all other pins - Transient voltage on BP, BM - - - Transient voltage on VBAT - - - Total power dissipation (all supplies and outputs) - - - Storage temperature - - - Junction temperature - - - Package body temperature - - - Humidity non-condensing - - Tamb Ambient temperature T Ambient temperature VCC - VIO Difference of supplies - - ICC VCC current consumption - - IIO VIO current consumption - - tSTBN_RxD Delay STBN high to RxD high with wake flag set - - tSTANDBY go-to STANDBY hold time - - VBUS_DIFF_D0 Differential bus voltage low in NORMAL mode (Data0) - - VBUS_DIFF_D1 Differential bus voltage high in NORMAL mode (Data1) - - General Parameters Supply Voltage State Transitions Transmitter www.austriamicrosystems.com Revision 17920-001-10a 25 - 33 AS8220A Objective Data Sheet - Appendix Table 10. Comparison table FlexRay Electrical Physical Layer Specification V2.1 RevB AS8220A Datasheet Symbol Parameter Name Description VBUS_DIFF Matching between Data0 and Data1 differential bus voltage in NORMAL mode - - VBUS_COM_D0 Common mode bus voltage in case of Data0 in NORMAL mode - - VBUS_COM_D1 Common mode bus voltage in case of Data1 in NORMAL mode - - VBUS_COM Matching between Data0 and Data1 common mode voltage - - VBUS_DIFF_Idle Absolute differential bus voltage in idle mode uBDTxidle Absolute value of uBus, while Idle IBPBMShortMax IBMBPShortMax Absolute max current when BP is shorted to BM IBPBMShortMax IBMBPShortMax Absolute maximum output current when BP shorted to BM IBPGNDShortMax Absolute max current when BP is shorted to GND IBPGNDShortMax Absolute maximum output current when shorted to GND IBMGNDShortMax Absolute max current when BM is shorted to GND IBMGNDShortMax Absolute maximum output current when shorted to GND IBP-5VShortMax Absolute max current when BP is shorted to -5 V IBP-5VShortMax Absolute maximum output current when shorted to -5V IBM-5VShortMax Absolute max current when BM is shorted to -5 V IBM-5VShortMax A Absolute maximum output current when shorted to -5V IBP27VShortMax Absolute max current when BP is shorted to 27 V IBPBAT27VShortMax Absolute maximum output current when shorted to 27V IBM27VShortMax Absolute max current when BM is shorted to 27 V IBMBAT27VShortMax Absolute maximum output current when shorted to 27V IBP48VShortMax Absolute max current when BP is shorted to 48 V IBPBAT48VShortMax Absolute maximum output current when shorted to 48V IBM48VShortMax Absolute max current when BM is shorted to 48 V IBMBAT48VShortMax Absolute maximum output current when shorted to 48V tTxD_BUS01 Delay time from TxD to BUS positive edge dBDTx10 Transmitter delay, negative edge tTxD_BUS10 Delay time from TxD to BUS negative edge dBDTx01 Transmitter delay, positive edge tTxD_MISMATCH Delay time from TxD to BUS mismatch dTxAsym Transmitter delay mismatch | dBDTx10 - dBDTx01 | tBUS_10 Fall time differential bus voltage dBusTx10 Fall time differential bus voltage (80% → 20%) tBUS_01 Rise time differential bus voltage dBusTx01 Rise time differential bus voltage (20% → 80%) www.austriamicrosystems.com Revision 17920-001-10a 26 - 33 AS8220A Objective Data Sheet - Appendix Table 10. Comparison table FlexRay Electrical Physical Layer Specification V2.1 RevB AS8220A Datasheet Symbol Parameter Name Description tTxEN_BUS_Idle_Acti Delay time from TxEN to bus active dBDTxia Propagation delay idle →active tTxEN_BUS_Active_Id Delay time from TxEN to bus idle dBDTxai Propagation delay active → idle tTxEN_MISMATCH Delay time from TxEN to bus mismatch dBDTxDM | dBDTxia - dBDTxai | tBGE_BUS_Idle_Activ Delay time from BGE to bus active dBDTxia Propagation delay idle → active tBGE_BUS_Active_Idl Delay time from BGE to bus idle dBDTXai Propagation delay active → idle tBUS_Idle_Active Differential bus voltage transition time: idle to active dBusTxia Transition time idle → active tBUS_Active_Idle Differential bus voltage transition time: active to idle dBusTxai Transition time active → idle tTxEN_timeout TxEN timeout - - RBP, RBM BP, BM input resistance RCM1, RCM2 Receiver common mode input resistance RDIFF BP, BM differential input resistance - - VBPidle, VBMidle Idle voltage in NORMAL mode on pin BP,BM uBias Bus bias voltage during BD_Normal mode VBPidle_low, VBMidle_low Idle voltage in NORMAL mode on pin BP, BM uBias Bus bias voltage during low power modes IBPidle Absolute idle output current on pin BP - - IBMidle Absolute idle output current on pin BM - - IBPleak, IBMleak Absolute leakage current, when not powered iBPLeak, iBMLeak Absolute leakage current, when not powered VBUSActiveHigh Activity detection differential input voltage high uBusActiveHigh Upper receiver threshold for detecting activity VBUSActiveLow Activity detection differential input voltage low uBusActiveLow Lower receiver threshold for detecting activity VData1 Data1 detection differential input voltage uData1 Receiver threshold for detecting Data_1 VData0 Data0 detection differential input voltage uData0 Receiver threshold for detecting Data_0 VDataErr Mismatch between Data0 and Data1 differential input voltage uData Mismatch of receiver thresholds tBUS_RxD10 Delay from bus to RxD negative edge dBDRx10 Receiver delay, negative edge tBUS_RxD01 Delay from bus to RxD positive edge dBDRx01 Receiver delay, positive edge ve le e e Receiver www.austriamicrosystems.com Revision 17920-001-10a 27 - 33 AS8220A Objective Data Sheet - Appendix Table 10. Comparison table FlexRay Electrical Physical Layer Specification V2.1 RevB AS8220A Datasheet Symbol Parameter Name Description tBIT Bit time - - tRxD_ASYM Delay time from bus to RxD mismatch dRxAsym Receiver delay mismatch | dBDRx10 – dBDRx01 | tBUSIdleDetection Idle detection time dIdleDetection Filter-time for idle detection tBUSActivityDetection Activity detection time dActivityDetection Filter-time for activity detection tBUSIdleReaction Idle reaction time dBDRxai Idle reaction time tBUSActivityReaction Activity reaction time dBDRxia Activity reaction time VCCTHH VCC undervoltage recovery threshold - - VCCTHL VCC undervoltage detection threshold uUVCC Undervoltage detection threshold VIOTHH VIO undervoltage recovery threshold - - VIOTHL VIO undervoltage detection threshold uUVIO Undervoltage detection threshold tUV_DETECT Detection time for undervoltage at VCC, VIO dUVCC, dUVIO Undervoltage reaction time tUV_REC Detection time for undervoltage recovery at VCC, VIO - - ITHL Absolute bus current for low current detection - - ITHH Absolute bus current for high current detection - - VSHORT Differential voltage on BP and BM for detecting short circuit between bus lines - - tBUS_ERROR Bus error detection time - Detection only required while actively transmitting a data frame, error indication to host latest when transmission stops. OTTH Over temperature threshold - - OTTL Over temperature hysteresis - - uVIO-IN-HIGH Threshold for detecting a digital input as on logical high Supply Voltage Monitor Bus Error Detection Over Temperature Communication Controller Interface VTxDIH Threshold for detecting TxD as on logical high www.austriamicrosystems.com Revision 17920-001-10a 28 - 33 AS8220A Objective Data Sheet - Appendix Table 10. Comparison table FlexRay Electrical Physical Layer Specification V2.1 RevB AS8220A Datasheet Symbol Parameter Name Description VTxDIL Threshold for detecting TxD as on logical low uVIO-IN-LOW Threshold for detecting a digital input as on logical low ITxDIH TxD high level input current - - ITxDIL TxD low level input current - - VTxENIH Threshold for detecting TxEN as on logical high uVIO-IN-HIGH Threshold for detecting a digital input as on logical high VTXENIL Threshold for detecting TxEN as on logical low uVIO-IN-LOW Threshold for detecting a digital input as on logical low ITxENIH TxEN high level input current - - ITxENIL TxEN low level input current - - VRxDOH RxD high level output voltage uVIO-OUT-HIGH Output voltage on a digital output, when in logical high state VRxDOL RxD low level output voltage uVIO-OUT-LOW Output voltage on a digital output, when in logical low state VSTBNIH Threshold for detecting STBN as on logical high uVIO-IN-HIGH Threshold for detecting a digital input as on logical high VSTBNIL Threshold for detecting STBN as on logical low uVIO-IN-LOW Threshold for detecting a digital input as on logical low ISTBNIH STBN high level input current - - ISTBNIL STBN low level input current - - tSTBN_DEB_LP STBN de-bouncing time low power modes - - tSTBN_DEB_NLP STBN de-bouncing time non low power modes - - VERRNOH ERRN high level output voltage uVIO-OUT-HIGH Output voltage on a digital output, when in logical high state VERRNOL ERRN low level output voltage uVIO-OUT-LOW Output voltage on a digital output, when in logical low state uVIO-IN-HIGH Threshold for detecting a digital input as on logical high Host Interface Bus Guardian Interface VBGEIH Threshold for detecting BGE as on logical high www.austriamicrosystems.com Revision 17920-001-10a 29 - 33 AS8220A Objective Data Sheet - Appendix Table 10. Comparison table FlexRay Electrical Physical Layer Specification V2.1 RevB AS8220A Datasheet Symbol Parameter Name Description VBGEIL Threshold for detecting BGE as on logical low uVIO-IN-LOW Threshold for detecting a digital input as on logical low IBGEIH BGE high level input current - - IBGEIL BGE low level input current - - www.austriamicrosystems.com Revision 17920-001-10a 30 - 33 AS8220A Objective Data Sheet - Package Drawings and Markings 10 Package Drawings and Markings Figure 19. package Diagram Table 11. package Dimensions Symbol Min Typ A 1.73 1.86 A1 0.05 0.13 A2 1.68 1.73 b 0.25 b1 0.25 0.30 C 0.09 C1 0.09 0.15 D See Variations E 5.20 5.30 e 0.65 BSC H 7.65 7.80 Max 1.99 0.21 1.78 0.38 0.33 0.20 0.16 5.38 7.90 Symbol L L1 N R AA AB AC AD AE AF Min 0.63 0º 0.09 6.07 6.07 7.07 8.07 10.07 10.07 Typ 0.75 1.25 REF See Variations 4º 0.15 6.20 6.20 7.20 8.20 10.20 10.20 Max 0.95 8º 6.33 6.33 7.33 8.33 10.33 10.33 Note: 1. Dimensioning and tolerancing conform to ASME Y14.5M-1994. 2. All dimensions are in millimeters, angle is in degrees. 3. N is the total number of terminals. www.austriamicrosystems.com Revision 17920-001-10a 31 - 33 AS8220A Objective Data Sheet - Ordering Information 11 Ordering Information Table 12. Ordering Information Type Marking www.austriamicrosystems.com Description Revision 17920-001-10a Delivery Form Package 32 - 33 AS8220A Objective Data Sheet - Ordering Information Copyrights Copyright © 1997-2008, austriamicrosystems AG, Schloss Premstaetten, 8141 Unterpremstaetten, Austria-Europe. Trademarks Registered ®. All rights reserved. The material herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. All products and companies mentioned are trademarks or registered trademarks of their respective companies. Disclaimer Devices sold by austriamicrosystems AG are covered by the warranty and patent indemnification provisions appearing in its Term of Sale. austriamicrosystems AG makes no warranty, express, statutory, implied, or by description regarding the information set forth herein or regarding the freedom of the described devices from patent infringement. austriamicrosystems AG reserves the right to change specifications and prices at any time and without notice. Therefore, prior to designing this product into a system, it is necessary to check with austriamicrosystems AG for current information. This product is intended for use in normal commercial applications. Applications requiring extended temperature range, unusual environmental requirements, or high reliability applications, such as military, medical life-support or life-sustaining equipment are specifically not recommended without additional processing by austriamicrosystems AG for each application. For shipments of less than 100 parts the manufacturing flow might show deviations from the standard production flow, such as test flow or test location. The information furnished here by austriamicrosystems AG is believed to be correct and accurate. However, austriamicrosystems AG shall not be liable to recipient or any third party for any damages, including but not limited to personal injury, property damage, loss of profits, loss of use, interruption of business or indirect, special, incidental or consequential damages, of any kind, in connection with or arising out of the furnishing, performance or use of the technical data herein. No obligation or liability to recipient or any third party shall arise or flow out of austriamicrosystems AG rendering of technical or other services. Contact Information Headquarters austriamicrosystems AG A-8141 Schloss Premstaetten, Austria Tel: +43 (0) 3136 500 0 Fax: +43 (0) 3136 525 01 For Sales Offices, Distributors and Representatives, please visit: http://www.austriamicrosystems.com/contact www.austriamicrosystems.com B Revision 17920-001-10a 33 - 33