ITC100P Integrated Telecom Circuits Hook Switch Breakdown Voltage Bridge Rectifier Reverse Voltage Darlington Collector Current ITC100P 350 Units V 350 120 V mA Features • Small 16 Pin SOIC Package (PCMCIA Compatible) • Board Space and Cost Savings • No Moving Parts • 3750VRMS Input/Output Isolation • FCC Compatible Part 68 • Photodarlington Hook Switch • Full-Wave Bridge Rectifier • Darlington Transistor for Electronic Inductor “Dry” Circuits • Half Wave Current Detector for Ring Signal or Loop Current Detect • JEDEC Standard Pin Out Applications • Data/Fax Modem • Voice Mail Systems • Telephone Sets • Computer Telephony Integration • Set Top Box Modems Description The Integrated Telecom Circuit combines a high voltage optically isolated photodarlington, bridge rectifier, Darlington transistor and optocoupler into one 16 pin SOIC package, consolidating designs and reducing component count in telecom applications. The ITC100’s optocoupler provides for half wave detection of ring signals. Approvals • UL Recognized • EN 60950 Ordering Information Part # Description ITC100P ITC100PTR 16 Pin SOIC (50/Tube) 16 Pin SOIC (1000/Reel) Pin Configuration NC 1 16 Photodarlington LED 2 Anode Photodarlington LED 3 Cathode 15 Photodarlington Emitter 13 Bridge Output (-) NC 5 12 Bridge Input Collector -Phototransistor 7 Emitter -Phototransistor 8 www.clare.com 14 Darlington Base NC 4 NC 6 DS-ITC100P-R1.2 Darlington Emitter 11 Bridge Input 10 Phototransistor LED Anode 9 Phototransistor LED Cathode 1 ITC100P Absolute Maximum Ratings (@ 25˚ C) Parameter Total Package Dissipation Isolation Voltage Input to Output Operational Temperature Storage Temperature Soldering Temperature (10 Seconds Max.) 1 Min - Typ Max Units 11 W 3750 -40 -40 - - Absolute Maximum Ratings are stress ratings. Stresses in excess of these ratings can cause permanent damage to the device. Functional operation of the device at conditions beyond those indicated in the operational sections of this data sheet is not implied. VRMS +85 °C +125 °C +220 °C Above 25˚ derate linerity 8.33mw/˚C Total Power Dissipation (PD): PD=PHOOKSWITCH + PBRIDGE + PDARLINGTON + PLED PD=(RDS(on)) (I2L) + 2(VF)(IL) + (VCE)(IL) + (VLED)(IF) WHERE: RDS(on) = Maximum realy on resistance IL = Maximum loop current VF = Maximum diode forward voltage VCE = Maximum voltage collector to emitter VLED = Maximum LED forward voltage IF = Maximum LED current Electrical Characteristics Parameter Photodarlington Portion Collector-Emitter Breakdown voltage Collector Dark Current Collector Emitter Saturation Voltage Current Gain LED Input control Current LED input Voltage Drop LED Reverse Input Voltage LED Reverse Input Current Phototransistor Portion Phototransitor Blocking Voltage Phototransistor Dark Current Saturation Voltage Current Transfer Ratio LED Input control Current LED input Voltage Drop LED Input Current (Detector must be off) Bridge Rectifier Portion Reverse Voltage Forward Voltage Drop 2 Condition Symbol Min Typ Max Units IC = 100uA VCE = 200V IC = 100mA IB = 150uA Hfe IF = 5mA IR = 5V BVCEO ICEO VCE(S) 350 - - 100 1.2 V nA V IC= 40mA VCE =2V IF VF VR IR 2500 5 0.9 - 1.2 - 40000 50 1.4 5 10 mA V V mA IC = 10uA VCC = 5V IF = 0mA IC = 2mA IF = 16mA VCE = 0.5V IF = 6mA VCE = 0.5V IC = 2mA IF = 5mA VCE = 5V IC = 10uA BVCEO ICEO 20 - 50 50 500 V mA VSAT - 0.3 0.5 V CTR 33 400 - % IF 6 2 100 mA VF IF 0.9 5 1.2 25 1.4 - V uA IFD = 120mA VRD VFD - - 350 1.1 V V www.clare.com Rev. 1.2 ITC100P Electrical Characteristics Parameter Reverse Leakage Current Forward Current Continuous Forward Current Peak Darlington Portion Collector Emitter Voltage Collector Current Continous Off – State Collector Emitter Leakage Current DC Gain Current Saturation Voltage Total Harmonic Distortion Rev. 1.2 Condition TJ= 25oC VR = 350V TJ= 85oC T= 10mS IC=10mA DC IB=0 VC=3.5V VCE=10V IB=0mA VCE=5VDC IC=100mA IC=120mA F0=300Hz @ -10dBm IC=40mA Symbol IRD Min - Typ - Max 10 Units uA IFD IFD - - 50 140 0.5 uA mA A VCEO 20 - - V IC ICEX - - 120 1 mA uA hFE 300 - - - VCE(SAT) - - - 1.5 -80 V dB www.clare.com 3 MECHANICAL DIMENSIONS 10.160 0.381 (0.400 0.015) 16 Pin SOIC (“P” Suffix) PC Board Pattern (Top View) 1.270 TYP. (0.050 TYP.) 1.270 (0.050) 1.981 TYP. (0.078 TYP.) 2.108 MAX. (0.083 MAX.) 7.493 (0.295 1.016 TYP. (0.040 TYP.) 0.254 (0.010 0.127 0.005) 10.363 0.127 (0.408 0.005) 9.728 0.051 (0.383 0.002) 0.0127 0.0005) 1.193 (0.047) 0.406 TYP. (0.016) TYP. 0.787 (0.031) 8.890 TYP. (0.350 TYP.) Tape and Reel Packaging for 16 Pin SOIC Package 330.2 DIA. (13.00 DIA.) Top Cover Tape Thickness 0.102 MAX. (0.004 MAX.) 1 16 16.30 MAX. (0.642 MAX.) 10.70 (0.421) Top Cover Tape 12.00 (0.172) Embossed Carrier Embossment 2.70 (0.106) 10.90 (0.430) User Direction of Feed 4.90 (0.193) Dimensions mm (inches) For additional information please visit our website at: www.clare.com Clare, Inc. makes no representations or warranties with respect to the accuracy or completeness of the contents of this publication and reserves the right to make changes to specifications and product descriptions at any time without notice. Neither circuit patent licenses nor indemnity are expressed or implied. Except as set forth in Clare’s Standard Terms and Conditions of Sale, Clare, Inc. assumes no liability whatsoever, and disclaims any express or implied warranty, relating to its products including, but not limited to, the implied warranty of merchantability, fitness for a particular purpose, or infringement of any intellectual property right. The products described in this document are not designed, intended, authorized or warranted for use as components in systems intended for surgical implant into the body, or in other applications intended to support or sustain life, or where malfunction of Clare’s product may result in direct physical harm, injury, or death to a person or severe property or environmental damage. Clare, Inc. reserves the right to discontinue or make changes to its products at any time without notice. Specification: DS-ITC100P-R1.2 ©Copyright 2003, Clare, Inc. OptoMOS® is a registered trademark of Clare, Inc. All rights reserved. Printed in USA. 2/24/03